ST Engineering Telematics Wireless FP200HH Dual Frequency Hand Held Reader User Manual Default Normal

Telematics Wireless Ltd. Dual Frequency Hand Held Reader Default Normal

Contents

Users Manual Revision 2

REV. ∆ DESCRIPTION E.C.N. DATE DRAWN CHECKED
A 086 22/01/05
B According to FCC remarks
C FCC remarks 4/26/2005
D FCC remarks 5/25/2005
PROPRIETARY INFORMATION
ALL RIGHTS RESERVD, NO PARTS OF THIS DOCUMENT MAY BE REPRODUCED, STORD IN
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC,
MECHANICAL PHOTOCOPYING, RECORDING OR OTHERWISE WITHOUT THE PRIOR WRITTEN
PERMISSION OF TELEMATICS WIRELESS LTD. NOR USED IN WHOLE OR IN PART FOR ANY
PURPOSE OR FOR ANY CUSTOMER EXCEPT TELEMATICS WIRELESS.
DESIGNED G.F.K. 10-Feb-2005 SHEET/OF
CHECKED Y.S. 14-Feb-2005
APPROVED M.N. 14-Feb-2005
NAME:
TDMA Reader-FP200HH
User Manual Q.A. A.S. 15-Feb-2005
1
8
PROD/PROJ: HANDHELD READER
2
1
4
0
7
2
0
1
7
0
0
0
SIZE
A
Note:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING! Changes or modifications to this unit not expressly approved by Telematics
Wireless Ltd. could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his,
own expense.
The antenna is printed on the circuit board and is an integral part of the unit.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
2140-72017-00-0A REV: D Page 2 Of 8
FP200HH User Manual
Table Of Contents
1. GENERAL INFORMATION ...............................................................................................4
1.1 INTRODUCTION.............................................................................................................................. 4
1.2 PURPOSE........................................................................................................................................ 4
1.3 PREPARATION................................................................................................................................4
2. CONTROLS AND INDICATORS .......................................................................................5
2.1 TDMA READER ............................................................................................................................ 5
2.2 CHARGING..................................................................................................................................... 7
2.3 ERRORS CONDITIONS .................................................................................................................... 8
2140-72017-00-0A REV: D Page 3 Of 8
FP200HH User Manual
1. General Information
1.1 Introduction
The Handheld Reader (HH Reader) is a dual frequency, TDMA reader to be used in mobile
application where the lightweight and friendly user interface is mandatory.
The HH Reader provides information access and setting for Telematics-Wireless electronic
seals and transponders.
Note: Everywhere 2.4 GHz is mentioned, the actual real frequency is 2.44 GHz.
1.2 Purpose
The purpose of this document is to provide detail instruction for activating the HH Reader.
1.3 Preparation
Before initializations of the HH Reader, make sure you have the following:
1. 1 x HH Reader
2. 1 x AC line charger
3. 1 x Dual frequency Telematics-Wireless electronic seal.
2140-72017-00-0A REV: D Page 4 Of 8
FP200HH User Manual
2. CONTROLS and INDICATORS
2.1 TDMA Reader
The ON/OFF switch of HH Reader is the ON/OFF switch of the iPAQ.
After turning the unit ON, the iPAQ will display the same display as before turning it OFF.
If the system window shown in Fig.1 appears, push the right upp er switch, Fig.2, of the iPAQ
lower part and get Fig.3 application screen.
ON/OFF switch
Application switch
Fig. 1: System screen Fig. 2: Application swich
Select “Enter” and get “Tag Search” screen – Fig.4
Select “Tag search” and get in the list, the tag that is being used in this procedure. – Fig.5
Fig. 3: Application screen Fig.4: Tag search screen Fig. 5: Tag list
2140-72017-00-0A REV: D Page 5 Of 8
FP200HH User Manual
Change frequency to 2.4 GHz – Fig.6
Select “Tag search” and get in the list, the tag that is being used in this procedure. – Fig.7
Fig. 6: 2.4 GHz Fig.7: 2.4 GHz Tag list
Select “exit” and exit the application to system screen
Now you can turn the power OFF.
2140-72017-00-0A REV: D Page 6 Of 8
FP200HH User Manual
2.2 Charging
The HH Reader has a single charger for both the iPAQ and the reader electronic board. The
charger connector is located in the HH Reader bottom side.
Open the black rubber cover on the bottom side of the HH Reader – See Fig.8.
Connect the charger to charger connector of the HH Reader, – See Fig.9.
Wait for the power indicator of the iPAQ, see Fig.10, to stop blinking and turn ON constantly.
Now the HH Reader is fully charged.
Note: When operating from battery, this indicator is OFF.
`
Charger
Connector
Bottom
Cover
Fig. 8: Bottom cover Fig.9: Charger connector
Fig.10: Charger indicator
2140-72017-00-0A REV: D Page 7 Of 8
FP200HH User Manual
2140-72017-00-0A REV: D Page 8 Of 8
2.3 Errors Conditions
Error message Reason To do
TDMA reader is off
Coomunication with
TDMA reader lost
1. Exit application
2. Turn TDMA reader on
3. Restart application
RF interference
Reader not pointing seal
Seal out of range
1. Make sure within range
2. Hold reader toward seal
3. Redo last operation

Navigation menu