ST Microelectronics S R L SPBT40DP SPBT4.0DP Bluetooth Dual Radio Module User Manual SPBT40DP Datasheet r0 15 Rizzoli

ST Microelectronics S.R.L. SPBT4.0DP Bluetooth Dual Radio Module SPBT40DP Datasheet r0 15 Rizzoli

Datasheet

 July  2015  DocID0xxxxx Rev 0.15   This is preliminary information on a new product now in development or undergoing   evaluation.  Details are subject to change  without notice. www.st.com SPBT4.0DP    Bluetooth® Smart Ready module    Datasheet – preliminary data  Features  • •Bluetooth® radio o  Fully  embedded  Bluetooth®  v4.0  with SPP and Low Energy profiles o  Embedded support for MFI iAP2 profile o  Class 2 module o  Complete RF ready module o  128-bit encryption security o  Integrated antenna •  ST micro Cortex-M4 microprocessor  o  up to 104 MHz  o  512 KB Flash o  128 KB RAM memory •  Supported transmission speed with SPP o  Up to 800KBits •  General I/O o  8 general purpose I/Os •  User interface o  AT command Data Package (DP) o  Firmware upgrade over UART •  ETSI, FCC, IC and Bluetooth® qualified •  Single voltage supply: 3.3 V typical •  Micro-sized form factor: 11.6 x 13.5 x 2.9 mm •  Operating temperature range: -40 °C to 85 °C
   Contents 1 Description .......................................................................................................................... 5 2 RoHS compliance ................................................................................................................ 6 3 Applications ......................................................................................................................... 6 4 Software architecture .......................................................................................................... 7 4.1 BT stack layers ................................................................................................................. 7 4.2 Supported Profile ............................................................................................................. 7 4.3 AT Command DATA PACKAGE ....................................................................................... 7 5 Hardware specifications...................................................................................................... 8 5.1 Recommended operating conditions .............................................................................. 8 5.2 Absolute maximum ratings .............................................................................................. 8 5.3 Modulei current absorption ............................................................................................. 8 5.4 Pin assignment ................................................................................................................. 9 5.5  Mechanical dimensions ................................................................................................. 10 6 Hardware design .................................................................................................................... 12 6.1 Reflow soldering ............................................................................................................. 12 6.2 UART interface ............................................................................................................... 14 7 Regulatory compliance ..................................................................................................... 15 7.1 FCC  certification ............................................................................................................ 15 7.1.1 Labeling instructions ............................................................................................... 15 7.1.2 Product manual instructions ................................................................................... 16 7.2 IC certification ................................................................................................................. 17 7.2.1 Labeling instructions ............................................................................................... 17 7.2.2 Product manual instructions ................................................................................... 18 7.3 Bluetooth certification .................................................................................................... 19 7.4 CE certification ............................................................................................................... 19 8 Traceability ......................................................................................................................... 20 9 Ordering information ......................................................................................................... 21 10 Revision history ................................................................................................................. 22
List of tables  3 | P a g e    List of tables    Table 1.  Recommended operating conditions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8 Table 2.  Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8 Table 3.  Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9 Table 4.  Soldering . . . .  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Table 5.  Traceability information. . . .  . .  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  Table 6.  Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Table 7.  Document revision history  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
List of figures  4 | P a g e    List of figures    Figure 1.  Pin connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9 Figure 2.  Mechanical dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 3.  Recommend land pattern top view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 4.  Soldering profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 5.  Connection to host device  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 6.  Typical RS232 circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
 5 | P a g e    1  Description   The SPBT4.0DP  is an easy to use Bluetooth Smart Ready module, compliant with Bluetooth v4.0.  The  module  is  among  the  smallest  form  factor  available  which  provides  a  complete  RF platform.  The  SPBT4.0DP  enables  electronic  devices  with  wireless  connectivity,  not requiring  any  RF  experience  or  expertise  for  integration  into  the  final  product.  The SPBT4.0DP   module, being a  certified solution, optimizes the  time to  market of  the  final applications.  The module is designed for maximum performance in a minimal space including fast speed UART and 8 general purpose I/O lines, several serial interface options, and up to 800 kbps transmission speed with SPP service active, 250kbps with iAP2 service active.  Optimized design allows the integration of a complete working Bluetooth modem, including antenna,  in  the  minimum  possible  size;  only  an  additional  external  LPO  (low  power oscillator) is required to enable low power mode capability.  The SPBT4.0DP  is a surface mount PCB module that provides fully embedded, ready to use  Bluetooth  wireless  technology.  The  reprogrammable  Flash  memory  contains embedded  firmware  for  serial  cable  replacement  using  the  Bluetooth  SPP  profile. Embedded Bluetooth DATA PACKAGE (DP) firmware is a friendly interface, which realizes a simple control for cable replacement. The SPBT4.0DP supporting SPP, iAP2 and Bluetooth Low  Energy proprietary Data  Exchange  profiles,  it  provides communication with  Android, smartphone, and the newest Apple® iOS Bluetooth enabled devices.    An Apple authentication IC is required to exchange data with an Apple device or access an Apple  device  application.  The  DP  FW  includes  the  Bluetooth  iAP2  profile  capable  of recognizing the Apple authentication chip.  Customers using the Apple authentication IC must register as developers to become an Apple  certified  MFI  member.  License  fees  may  apply,  for  additional  information visit: http://developer.apple.com/programs/which-program/index.html.  Certified MFI developers developing electronic accessories that connect to the iPod®, iPhone®, and iPad® gain access to technical documentation, hardware components, technical support and certification logos.  Customized  firmware  for  peripheral  device  interaction,  power  optimization,  security,  and other proprietary features may be supported and can be ordered pre-loaded and configured.
 6 | P a g e    2  RoHS compliance   ST Bluetooth modules comply with the ECOPACK2 level of RoHS compliance grade.     3  Applications  The SPBT4.0DP  is suitable for a wide range of application like:  •  Serial cable replacement •  M2M industrial control •  Service diagnostic •  Data acquisition equipment •  Machine control •  Sensor monitoring •  Security system •  Mobile health
 7 | P a g e    4  Software architecture   4.1  BT stack layers  •  Bluetooth v4.0 •  Device power modes: active, sleep and deep sleep •  Wake on Bluetooth feature optimized power consumption of host CPU •  Authentication and encryption •  Encryption key length from 8 bits to 128 bits •  Persistent Flash memory for BD address and user parameter storage •  All ACL (asynchronous connection less) packet types •  Sniff mode: fully supported to maximum allowed intervals •  Master slave switch supported during connection and post connection •  Dedicated inquiry access code for improved inquiry scan performance •  Dynamic packet selection channel quality driven data rate to optimize link performance •  Dynamic power control •  Bluetooth radio natively supports 802.11b co-existence AFH •  RFCOMM, SDP, and L2CAP supported   4.2  Supported Profile     Bluetooth Classic: •  Serial Port Profile (SPP)  •  iPOD Accessory Protocol 2 (iAP2)  Bluetooth Low Energy: •  Proprietary Data Exchange Profile (DEP)       4.3  AT Command DATA PACKAGE  The complete command list  is reported in the AT Command DATA PACKAGE user manual.
 8 | P a g e   5  Hardware specifications   General conditions (VIN = 3.3 V and 25 °C).   5.1  Recommended operating conditions   Table 1. Recommended operating conditions  Rating Min. Typical Max. Unit Operating temperature range -40 -          + 85 °C Supply voltage VIN 2.3 3.3 3.6 V Signal pin voltage - 2.1 - V RF frequency 2402 -  2480 MHz   5.2  Absolute maximum ratings   Table 2. Absolute maximum ratings  Rating Min. Typical Max. Unit Storage temperature range -40 - +  85 °C Supply voltage, VIN -0.3 -  + 5.5 V I/O pin voltage, VIO -0.3  +2.1    +5 V RF max. input power GFSK - - 10 dBm RF max. input power DQPSK - - 6 dBm RF max. input power DPSK - - -3 dBm      5.3  Module current  absorption (Average & Typical)   Table 3. Module average D.C. current absorption  Test Conditions Min. Typical Max. Unit CPU = 84Mhz IDLE STATE (WAIT FOR  COMMANDS)  10.62  mA CPU = 84Mhz Tx (65500kb/s)  Transmission state (Continuos Transmission)  37  mA CPU = 84Mhz Rx (35500kb/s) Receiving state  27  mA
 9 | P a g e     5.4  Pin assignment   Figure 1. Pin connection                                  Table 4. Pin assignment  Pin  Name  Description  I/O  Note 1  GPIO1_BTCS  GPIO indicating BT Connection Status -  When high, BT connection is active -  When low, BT connection is not active O   2  GPIO2  General purpose I/O  I/O  5V tolerant 3  GPIO3  General purpose I/O  I/O  5V tolerant 4  GPIO4_MLPS  GPIO indicating Module Low Power Status -  When high, device is in active mode -  When low, device is in low power mode O   5  GPIO5   General purpose I/O   I/O  5V tolerant 6  GPIO6   General purpose I/O   I/O  5V tolerant 7  GND  Reference ground  NA   8  Vin  Main power supply input   NA   9  Boot 0  Boot 0 pin  I  5V tolerant 10  RESETn  Reset input (active low for 5ms)  I   11  CTS /  I2C SCL  Request to send (active low) or I2C_SCL line for MFI chip  I   12  RTS / I2C SDA  Clear to send (active low) or I2C_SDA line for MFI chip  O  5V tolerant 13  RXD  Receive Data  I  5V tolerant 14  TXD  Transmit Data  O   15  LPO  Low power 32KHz oscillator input  I   16  GPIO7  General purpose I/O  I/O  5V tolerant 17  GPIO8  General purpose I/O  I/O  5V tolerant 18  +2.1V OUT  +2.1V out (max 10mA)  NA
 10 | P a g e     5.5   Mechanical dimensions  Figure 2. Mechanical dimensions
 11 | P a g e    Figure 3. Recommend land pattern top view
 12 | P a g e   6 Hardware design  SPBT4.0DP  module with DP command embedded FW supports UART, I2C and GPIO hardware interfaces.  Note: -  All unused pins should be left floating; do not ground.  •  All GND pins must be well grounded.  •  The area around the module should be free of any ground planes, power planes, trace routings, or metal for 6 mm from the module antenna position, in all directions.  •  Traces should not be routed underneath the module.   6.1 Reflow soldering  The SPBT4.0DP is a high temperature strength surface mount Bluetooth® module supplied on an 18 pin, 6-layer PCB. The final assembly recommended reflow profiles are indicated here below.  Soldering  phase  must  be  executed  with  care:  in  order  to  avoid  undesired  melting phenomenon, particular attention must be paid to the set-up of the peak temperature.  Here  following  some  suggestions  for  the  temperature  profile  based  on  the  following recommendations.      Table 5. Soldering   Profile feature PB-free assembly Average ramp-up rate (TSMAX to TP) 3 °C/sec max Preheat: – Temperature min. (TS min.) – Temperature max. (TS max.) – Time (ts min. to ts max.)(ts)  150 °C 200 °C 60-100 sec Time maintained above: – Temperature TL – Temperature TL  217 °C 60-70 sec Peak temperature (TP)  240 + 0 °C Time within 5 °C of actual peak temperature (TP)  10-20 sec Ramp-down rate  6 °C/sec Time from 25 °C to peak temperature  8 minutes max.
 13 | P a g e    Figure 4. Soldering profile                           $012026Y1
 14 | P a g e    6.2  UART interface  The UART is compatible with the 16550 industry standard. Four signals are provided with the UART interface. The TXD and RXD pins are used for data while the CTS and RTS pins are used for flow control.  Figure 5. Connection to host device       Host Bluetooth module      $012027Y1  Figure 6. Typical RS232 circuit                      $012028Y1
 15 | P a g e    7  Regulatory compliance   7.1  FCC  certification  This module has been tested and found to comply with the FCC part 15 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference may not occur in a particular installation.  This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:  1  This device may not cause harmful interference,  and  2  this device must accept any interference received, including interference that may cause undesired operation.  Modifications or changes to this equipment not expressly approved by STMicroelectronics may render void the user's authority to operate this equipment.  Modular approval  FCC ID: S9NSPBT40DP  In accordance with FCC part 15, the SPBT4.0DP is listed as a modular transmitter device.  This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with colocation and RF exposure requirements in accordance with FCC multi-transmitter product procedures. Collocated transmitters operating in portable RF Exposure conditions (e.g. <20 cm from persons including but not limited to body worn and hand held devices) may require separate approval.  7.1.1 Labeling instructions  When integrating the SPBT4.0DP  into the final product, the OEM must ensure that the FCC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning):  Contains FCC ID: S9NSPBT40DP  OR  This product contains FCC ID: S9NSPBT40DP  The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  1  this device may not cause harmful interference, and  2  this device must accept any interference received, including any interference that may cause undesired operation.
 16 | P a g e      7.1.2 Product manual instructions  This section applies to OEM final products containing the SPBT4.0DP  module, subject to FCC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning):  Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (Part. 15.21)  In the case where an OEM seeks Class B (residential) limits for the final product, the following statement must be included in the final product manual:  Note:       This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  •  Reorient or relocate the receiving antenna.  •  Increase the separation between the equipment and receiver.  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  •  Consult the dealer or an experienced radio/TV technician for help.   In the case where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual:  Note:       This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense.
 17 | P a g e      7.2 IC certification  The SPBT4.0DP module has been tested and found compliant with the IC RSS-210 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference may not occur in a particular installation.  This device complies with RSS-210 of the IC rules. Operation is subject to the following two conditions:  1  this device may not cause harmful interference, and  2  this device must accept any interference received, including interference that may cause undesired operation.   Modifications or changes to this equipment not expressly approved by STMicroelectronics may render void the user's authority to operate this equipment.  Modular approval  IC: 8976C-SPBT40DP In accordance with IC RSS-210, the SPBT4.0DP is listed as a modular transmitter device.  This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with colocation and RF exposure requirements in accordance with IC multi-transmitter product procedures. Collocated transmitters operating in portable RF Exposure conditions (e.g. <20cm from persons including but not limited to body worn and hand held devices) may require separate approval.    7.2.1 Labeling instructions  When integrating the SPBT4.0DP  into the final product, the OEM must ensure that the IC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates that the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning):  Contains IC: 8976C-SPBT40DP   OR   This product contains IC: 8976C-SPBT40DP  The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches):  This device complies with RSS-210 of the IC Rules. Operation is subject to the following two conditions:  1  this device may not cause harmful interference, and  2  this device must accept any interference received, including any interference that may cause undesired operation.
 18 | P a g e       7.2.2 Product manual instructions  This section applies to OEM final products containing the SPBT4.0DP  module, subject to IC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning):  Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (RSS-210)  In the case where an OEM seeks Class B (residential) limits for the final product, the following statement must be included in the final product manual:  Note:       This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to RSS-210 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  •  Reorient or relocate the receiving antenna.  •  Increase the separation between the equipment and receiver.  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  •  Consult the dealer or an experienced radio/TV technician for help.   In the case where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual:  Note:       This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to RSS-210 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense.
 19 | P a g e   7.3 Bluetooth certification  Module with embedded stack and profile has been qualified according to SIG qualification rules: –  Bluetooth SIG Declaration ID: zzzzzz –  Product type: End Product –  Core spec version: 4.0 –  Product descriptions: Bluetooth module, spec V4.0   7.4  CE certification  Module has been certified according to following certification rules: –  CE Expert opinion: 0564-ARSP00100 –  Measurements have been performed in accordance with (report available on request): –  EN 300 328 v 1.8.1 (2012-06) ; v1.9.1 (2015-02) –  EN 301 489-17 V 2.2.1 (2012-09) -–  EN 62479 (2010-09)  -–  EN60950- 1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 CE certified:
 20 | P a g e    8 Traceability   Each module is univocally identified by serial number stored in a 2D data matrix laser marked on the bottom side of the module itself.  The serial number has the following format:  WW YY D FF NNN   Table 5. Traceability information  Letter  Meaning  WW  week YY  year D  Product ID number FF  Production panel coordinate identification  NN  Progressive serial number    Each module bulk is identified by a bulk ID. BULK ID and module 2D data matrix are linked by a reciprocal traceability link. The module 2D data matrix traces the lot number of any raw material used.
 21 | P a g e   9  Ordering information    Table 6. Ordering information   Order code Description Packing MOQ SPBT4.0DP   Class 2 OEM Bluetooth antenna module Jedec tray  2448 pcs
 22 | P a g e    10  Revision history   Table 7. Document revision history   Date Revision     Changes 07-July- 2015 0.14  First release. 31 – July - 2015 0.15 Modified table 3
 23 | P a g e                                    IMPORTANT NOTICE  - PLEASE READ CAREFULLY:    STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement  Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products   No license, express or implied, to any intellectual property rights is granted by ST herein.   Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.   ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.   Information in this document supersedes and replaces information previously supplied in any prior versions of this document.   © 2015 STMicroelectronics - All rights reserved    www.st.com

Navigation menu