ST Microelectronics S R L SPWFS04 SPWF04SA / C Wi-Fi Module User Manual Serial to Wi Fi b g n intelligent modules
ST Microelectronics S.R.L. SPWF04SA / C Wi-Fi Module Serial to Wi Fi b g n intelligent modules
Users manual
SPWF04SA SPWF04SC Serial-to-Wi-Fi b/g/n intelligent modules Preliminary Datasheet – 13.7 dBm @ 54 Mbps OFDM RX sensitivity – -96.0 dBm @ 1 Mbps DSSS – -74.5 dBm @ 54 Mbps OFDM 16 configurable GPIOs available UART and SPI interface to host system Advanced low-power modes – Standby with RTC: 0.8mA (TBC) – Sleep connected (DTIM=1): 19 mA – RX traffic 113 mA typical – TX traffic 248 mA typical @ 18 dBm Features 2.4 GHz IEEE 802.11 b/g/n transceiver STM32 ARM Cortex-M4, with 256 KB RAM and 2 MB Flash memory Integrated TCP/IP protocol stack – 2 (TBC) simultaneous TCP or UDP clients and 2 (TBC) socket server – supporting up to TLS 1.2, including common encryption algorithms: AES (128, 256), hash (MD5, SHA-1, SHA256) and public key algorithms (RSA, ECC) – Web server supporting dynamic web pages WEP/WPA/WPA2 personal and enterprice security System modes: Station, IBSS, and miniAP miniAP easily provisioned (SSID, PWD) Small form factor: 26.92 x 15.24 x 2.35 mm Single voltage supply (3.3 V typical) Multiple antenna options: – Integrated antenna (SPWF04SA versions) – Integrated u.fl connector (SPWF04SC versions) Industrial temperature range: -40 °C to 85 °C FCC/CE/IC/SRRC certified RoHS compliant Surface mount PCB module Applications Fast Wi-Fi reassociation after reset Firmware update via UART and Over The Air (FOTA TX power – 18.3 dBm @ 1 Mbps DSSS Simple AT command set host interface through UART Smart appliances Industrial control and data acquisition Home automation and security systems Wireless sensors Cable replacement Medical equipment Machine-to-machine communication April 2016 DocID025635 Rev 7 1/18 www.st.com Description SPWF04SA, SPWF04SC Description The SPWF04SA and the SPWF04SC intelligent Wi-Fi modules represent a plug-and-play and standalone 802.11 b/g/n solution for easy integration of wireless Internet connectivity features into existing or new products. Configured around a single-chip 802.11 transceiver with integrated PA and comprehensive power management subsystem, and an STM32 microcontroller with an extensive GPIO suite, the modules also incorporate timing clocks and voltage regulators. Two different options exist based on the integrated Flash memory. The module is available either configured with an embedded micro 2.45 GHz highly-efficient ISM band antenna (SPWF04SA), or with an u.fl connector for external antenna connection (SPWF04SC). With low power consumption and ultra-compact (2.7 x 1.5 cm) footprint, the modules are ideal for fixed and mobile wireless applications, as well as challenging battery-operated applications. The SPWF04Sx parts are released with an integrated full featured TCP/IP protocol stack with added web server and additional application service capabilities, such as REST API for accessing files on servers in the cloud and support for dynamic web pages with CGI/SSI functions to easily interact with the module and the host processor over the air. For secure end-to-end communication with the cloud, an SSL/TLS stack is embedded in every module with no licensing charge. See application note AN4683 (TBC) for details. The SW package also includes an AT command layer interface for user-friendly access to the stack functionalities via the UART serial port. For details, see user manual UM1695 (TBC). It is always possible to upgrade the module firmware via UART and Over The Air (FOTA). Inside of the 2 MB extended Flash available on the SPWF04S module, 1 MB of the Flash is dedicated to FW upgrade and to host proprietary files, organized in a file system image, accessible through the integrated web server. FOTA is also possible with the SPWF04Sx module. ST may update the FW provided with the modules at any time. ST recommends that users regularly check for documentation and the current FW version available at www.st.com/wifimodules. 2/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Description Figure 1. Block diagram DocID025635 Rev 7 3/18 General electrical specifications SPWF04SA, SPWF04SC General electrical specifications Table 1. Absolute maximum ratings Parameter Test condition/comment Voltage supply Min. Typ. -0.3 Vin for 5 V tolerant pins -0.3 Vin for all other pins Storage temperature range -0.3 -55 Max. Unit 4.0 5.5 3.6 105 °C Table 2. Operating conditions and input power specifications(1) Parameter Operating temperature range Test condition/comment Min. Typ. Max. Unit 85 °C 3.6 Industrial -40 Input supply voltage 3.3 V supply input 3.1 Standby Both the STM32 and the radio are in standby power states 0.8 mA Sleep The STM32 is in stop power state and the radio is in sleep power state 19 mA Low power state The STM32 is active and the radio is in sleep power state 52 mA 236 mA 802.11b TX power=10 dBm 250 mA TX power=18 dBm 344 mA TX power=0 dBm 210 mA 802.11g TX power=10 dBm 243 mA TX power=18 dBm 338 mA 802.11b 105 mA 802.11g 105 mA 3.3 V supply TX power=0 dBm 3.3 TX RX 1. Typical results are at room temperature only. 4/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Digital interface specifications Digital interface specifications Table 3. Digital interface specifications, I/O pins Parameter Inputs Test condition/comment Min. VIH 2.3 VIL VOH IOH=4 mA 2.4 VOL IOL=4 mA Outputs DocID025635 Rev 7 Typ. Max. Unit 3.6 0.9 3.6 0.4 5/18 RF characteristics SPWF04SA, SPWF04SC RF characteristics Table 4. RF characteristics Parameter RX sensitivity(1) Test condition/comment Typ. Max. Unit 11b, 1 Mbps -96 dBm 11b, 2 Mbps -93 dBm 11b, 5.5 Mbps -91 dBm 11b, 11 Mbps -87 dBm 11g, 9 Mbps -89.5 dBm 11g, 18 Mbps -86 dBm 11g, 36 Mbps -80 dBm 11g, 54 Mbps -74.5 dBm 11n, MCS1, 13 Mbps -86.5 dBm 11n, MCS3, 26 Mbps -81.5 dBm 11n, MCS5, 52 Mbps -74 dBm 11n, MCS7, 65 Mbps -71 dBm dB -20 dBm 11Mbps 38 dBc 9 Mbps 20 dBc 54 Mbps dBc MCS1 24 dBc MCS7 dBc 18.3 dBm 18.3 dBm Channel-to-channel de-sensitivity CH1 to 14 11g, 54 Mbps, 10%PER Maximum input signal CH7 11g, 54 Mbps Adjacent channel rejection Min. 11b, 1 Mbps @ 11b spectral mask 11b, 11 Mbps 11g, 9 Mbps @ 11g spectral mask 18.3 dBm 11g, 54 Mbps EVM = -27 dB, 4.5% 13.7 dBm 11n, MCS1 @ 11n spectral mask 18.3 dBm 11n, MCS7 EVM = -27 dB 13.5 dBm On-board antenna gain Average -1.2 dBi External antenna gain SG901-1066 average including cable loss 2.8 dBi TX output power (1) 1. Output power and sensitivities are measured with a 50 Ω connection at the antenna port. 6/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Pinout description Pinout description Table 5. Pinout description Signal name Type Pin number Main function Alternate functions(1) Notes GPIO - general purpose input/output GPIO[0] I/O 16 General purpose input/output Restore to factory settings(2) GPIO[1] I/O 17 General purpose input/output/ADC GPIO[2] I/O 19 General purpose input/output/PWM GPIO[3] I/O General purpose input/output GPIO[6] I/O 22 GPIO[4] I/O 18 GPIO[5] I/O 20 GPIO[7] I/O 13 GPIO[8] I/O GPIO[9] I/O General purpose input/output Wake Up/Sleep Inhibit(3) General purpose input/output Input pull down and 5V tolerant Input pull down and 5V tolerant Floating and 5V tolerant Input pull down and 5V tolerant Input pull down and 5V tolerant General purpose input/output General purpose input/output STA/Mini AP Switch/WPS Pushbutton (4) General purpose input/output General purpose input/output/SPI nHostInterrupt GPIO[11] I/O 11 GPIO[12] I/O 12 General purpose input/output GPIO[15] I/O 21 General purpose input/output/DAC Monitoring purpose with no alternate function GPIO[10] I/O Drives LED, Blinks while running GPIO[13] I/O 15 Drives LED, Wi-Fi link up DocID025635 Rev 7 7/18 Pinout description SPWF04SA, SPWF04SC Table 5. Pinout description (continued) Signal name Type Pin number Main function GPIO[14] I/O 14 LED drive, Power up Alternate functions(1) Notes UART pins RXD / MOSI TXD / MISO 5V tolerant 5V Tolerant CTS / nCS Active low, 5V tolerant RTS / CLK 10 5V tolerant Reset RESETn Active low for 5 ms with pull up to 2.5VDC. Not 5V tolerant Reset input Supply pins and paddle Decouple with 10uF capacitor 3.3 V 24 Voltage supply Ground 23 Ground LSE 34 HSE 35 SWD I/O 26 SWD CLK 29 GPIO16 27 Not available GPIO17 28 Not available GPIO18 30 Not available SDIO CLK / SPI CLK SDIO D0 / SPI MISO SDIO CMD / SPI MOSI 31 32 33 Ground Paddle 25 Ground Add plenty of ground vias for thermal dissipation and ground return Boot loader BOOT0 Boot loader (5) 1. The activation of ALT function depends upon the firmware version or upon the variable configuration. 2. To perform the factory reset of the variables, pin GPIO0 must be high during powerup. 3. GPIO function running when low power mode variable is enabled. 4. Introduced with the release 3.0 of AT Full stack. To enable the STAToMiniAP switch the GPIO[7] needs to be put low together with the HW reset 8/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Pinout description 5. To enable the firmware download, pin BOOT0 needs to be high during power up. RESETn need to be pulled low at least 5 ms to initiate the firmware download sequence. Application guidelines The HOST processor should control the RESETn pin of the module in order to recover from unexpected behavior using the HW reset. DocID025635 Rev 7 9/18 Module reflow SPWF04SA, SPWF04SC Module reflow The SPWF04SA and SPWF04SC are surface mount modules with a 6-layer PCB. The recommended final assembly reflow profiles are indicated below. The soldering phase must be executed with care: in order to prevent an undesired melting phenomenon, particular attention must be paid to the setup of the peak temperature. The following are some suggestions for the temperature profile based on the IPC/JEDEC JSTD-020C, July 2004 recommendations. Table 6. Soldering values Profile feature PB-free assembly Average ramp-up rate (TSMAX to TP) 3 °C/sec max Preheat: – Temperature min. (Ts min.) – Temperature max. (Ts max.) – Time (Ts min. to Ts max) (ts) 150 °C 200 °C 60-100 sec Critical zone: Temperature TL 217 °C 60-70 sec Time TL Peak temperature (TP) 240 + 0 °C Time within 5 °C of actual peak temperature (TP) 10-20 sec Ramp-down rate 6 °C/sec Time from 25 °C to peak temperature 8 minutes max. Figure 2. Soldering profile AM17477v1 10/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Regulatory compliance Regulatory compliance RF compliance The RF certifications obtained are described in Table 7 below. Table 7. RF certification summary Comment FCC ID S9NSPWFS04 On board antenna and external ANTENOVA TITANIS with connector version IC ID 8976C-SPWFS04 On board antenna and external ANTENOVA TITANIS with connector version ETSI Compliant Approved with on board antenna and connector version This radio transmitter IC ID 8976-SPWFS04 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Note: The TITANIS antenna from ANTENOVA. is the only approved antenna using the u.fl connector version. SPWF04SA, SPWF04SC Regulatory compliance *Note all data provided in this table are based on the Antenova reference board FCC and IC This module has been tested and complies with the FCC part 15 and IC RSS-247 regulations. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. The device must not cause harmful interference. and 2. The device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by the party responsible for compliance may render void the user's authority to operate this equipment. The safe user distance, for RF Exposure, is ≥ 50mm (in compliance with 447498 D01 General RF Exposure Guidance v06 and RSS-102 Issue 5). Modular approval, FCC and IC FCC ID: S9NSPWFS04 IC: 8976C-SPWFS04 In accordance with FCC part 15, the modules SPWF04SA and SPWF04SC are listed above as a modular transmitter device. DocID025635 Rev 7 11/18 Regulatory compliance SPWF04SA, SPWF04SC Labeling instructions When integrating the SPWF04SA and SPWF04SC into the final product, it must be ensured that the FCC and IC labeling requirements specified below are satisfied. Based on the Public Notice from FCC, the product into which the ST transmitter module is installed must display a label referring to the enclosed module. The label should use wording like the following: Contains Transmitter Module FCC ID: S9NSPWFS04 IC: 8976C-SPWFS04 Any similar wording that expresses the same meaning may also be used. CE This module complies with the following European EMI/EMC and safety directives and standards: – ETSI EN 300 328 V1.8.1:2012 – EN 301 489-1 V1.9.2:2011 + EN 301 489-17 V2.2.1:2009 – EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 – EN 62479:2010 Figure 3. CE certified SRRC (T.B.C.) The SPWF04Sx module complies with Chinese SRRC certification. – SRRC CMIIT ID: (T.B.D.) (See the A.1 at the bottom of this document for the French translation) 12/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Figure 4. Top view of the module shield Shield CE Logo Figure 5. Bottom view of the module Data Matrix Board Design Reference Model Series Name zone FCC and IC ID zone DocID025635 Rev 7 13/18 Package information SPWF04SA, SPWF04SC Figure 6. Wi-Fi module dimensions Note: 14/18 An antenna area of 217 x 520 mils must be free of any ground metalization or traces under the unit. The area extending away from the antenna should be free from metal on the PCB and housing to meet expected performance levels. Pin 25 is the required paddle ground and is not shown in this diagram. DocID025635 Rev 7 SPWF04SA, SPWF04SC Package information Figure 7. Wi-Fi module footprint PCB design requires a detailed review of the center exposed pad. This pad requires good thermal conductivity. Soldering coverage should be maximized and checked via x-ray for proper design. There is a trade-off between providing enough soldering for conductivity and applying too much, which allows the module to “float” on the paddle creating reliability issues. ST recommends two approaches, a large center via that allows excess solder to flow down into the host PCB with smaller vias around it, or many smaller vias with just enough space for the viscosity of the chosen solder/flux to allow some solder to flow into the smaller vias. Either of these approaches must result in 60% or more full contact solder coverage on the paddle after reflow. ST strongly encourages PCB layout teams to work with their EMS providers to ensure vias and solder paste designs that will result in satisfactory performance. DocID025635 Rev 7 15/18 Regulatory compliance SPWF04SA/C Ordering information Table 8. Ordering information Order codes Note: Description SPWF04SA Wi-Fi module with integrated antenna, 1 MB of Flash and Wi-Fi full stack SPWF04SC Wi-Fi module with integrated ufl connector, 1 MB of Flash and Wi-Fi full stack Refer to the user manual for a complete list of features and commands available in the Wi-Fi full stack. Regulatory compliance SPWF04SA/C Déclaration de conformité A.1 Certification FCC Le module SPWF04SA/C a été testé et déclaré conforme avec la section 15 de la Règlementation FCC. Ces limitations sont stipulées afin de procurer une protection raisonnable contre les interférences gênantes dans les installations approuvées. Cet appareil génère, utilise et diffuse des ondes radio et, s’il n’est pas installé et utilisé en conformité avec les instructions dont il fait l’objet, peut causer des interférences gênantes sur les communications radio. Il n’y a cependant pas de garantie qu’une interférence ne se produira pas dans une installation particulière. Cet appareil est en conformité avec la section 15 des règlements FCC. L’utilisation est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences nocives, et (2) Cet appareil doit supporter toute interférence reçue, y compris des interférences qui peuvent provoquer un fonctionnement non désiré. Tout changement ou modification fait(e) à cet appareil et non expressément approuvé(e) par STMicroelectronics peut annuler l’autorisation pour l’utilisateur de faire fonctionner l’appareil. Approbation du module FCC ID: S9NSPWFS04 Conformément à la section 15 des règlements FCC, le module SPWF04SA/C est répertorié comme un dispositif émetteur modulaire. Ce module n’est évalué que pour une utilisation autonome. Les produits finis incorporant plusieurs émetteurs doivent être conformes à la colocation et aux exigences d'exposition RF en concordance avec les procédures FCC multi-émetteurs. D’autres émetteurs fonctionnant dans des dispositifs portables exposés aux RF (par exemple, situés à moins de 20 cm des personnes avec dispositifs portatifs ou portés contre le corps) peuvent nécessiter d'une approbation séparée. A.1.1 Instructions d'étiquetage Lors de l'intégration du module SPWF04SA/C dans le produit final, le fabricant doit s’assurer que les exigences en matière d'étiquetage de la FCC sont satisfaites . Une déclaration doit être placée sur l’étiquette extérieure du produit final indiquant que le produit comprend un module certifié. L'étiquette doit comporter les informations suivantes (ou une mention analogue que recouvre la même notion): OU Contient FCC ID: S9NSPWFS04 Ce produit contient FCC ID: S9NSPWFS04 Le sous-traitant doit inclure les énoncés suivants sur l’étiquette extérieure du produit final à moins que le produit ne soit trop petit (par exemple moins de 4 x 4 pouces): Cet appareil est en conformité avec la section 15 des règlements FCC. L’utilisation est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences nocives, et (2) Cet appareil doit supporter toute interférence reçue, y compris des interférences qui peuvent provoquer un fonctionnement non désiré. A1 DocID temporary Rev1 Regulatory compliance A.1.2 SPWF04SA, SPWF04SC Instructions pour l’utilisation du produit La présente section concerne les produits finis contenant le module SPWF04SA/C, assujettis aux normes FCC. Le manuel du produit final doit contenir la déclaration suivante (ou une mention analogue que recouvre la même notion): “ Avertissement: Les changements ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'autorisation de l'utilisateur de faire fonctionner cet équipement. (Section 15.21)” Dans le cas où le produit finis d’un fabriquant OEM rentre dans les limites de la Classe B (résidentiel), les énoncés suivants doivent être inclus dans le manuel du produit finis: “Remarque : Cet équipement a été testé et déclaré conforme aux limitations prévues dans le cadre de la classe B des appareils numériques, définies par la section 15 du règlement de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre toute interférence dangereuse issue d'une installation résidentielle. Cet équipement produit, utilise et peut émettre de l'énergie radio électrique et, s'il n'est pas installé et utilisé conformément aux présentes instructions, peut causer des interférences nuisibles aux communications radio. Cependant, il se peut que des interférences se produisent dans une installation particulière. Si cet appareil cause des interférences nuisibles à la réception des signaux de radio ou de télévision, ce qui peut être déterminé en allumant et en éteignant l'appareil, on encourage l'utilisateur d'essayer de corriger ces interférences par l'un des moyens suivants: – Réorienter ou repositionner l'antenne de réception. – Augmenter la distance séparant l’équipement du récepteur. – Connecter l’équipement à une prise appartenant à un circuit différent de celui sur lequel le récepteur est connecté. – Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.” Dans le cas où le produit fini d’un sous-traitant rentre dans les limites imposées aux appareils numériques de classe A, les énoncés suivants doivent être inclus dans le manuel du produit finis: “REMARQUE : Cet appareil a été testé et certifié conforme aux spécifications d'un appareil électronique de classe A (class A digital device), conformément à la partie 15 du règlement de la FCC. Ces contraintes sont destinées à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est utilisé dans une installation commerciale. Cet équipement produit, utilise et peut émettre de l'énergie radio électrique et, s'il n'est pas installé et utilisé conformément aux présentes instructions, peut causer des interférences nuisibles aux communications radio. L'utilisation de cet appareil dans une installation résidentielle peut entraîner des interférences nuisibles et l'utilisateur devra corriger les interférences à ses propres frais.” Regulatory compliance A.2 SPWF04SA, SPWF04SC Certification IC (a) Le module SPWF04SA/C a été testé et déclaré conforme avec la Règlementation IC CNR-210. Ces limitations sont stipulées afin de procurer une protection raisonnable contre les interférences gênantes en installations approuvées. Cet appareil génère, utilise et diffuse des ondes radio et, s’il n’est pas installé et utilisé en conformité avec les instructions dont il fait l’objet, peut causer des interférences gênantes sur les communications radio. Il n’y a cependant pas de garantie qu’une interférence ne se produira pas dans une installation particulière. Ce produit répond aux exigences de la norme CNR-210 d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences nocives, et (2) Cet appareil doit supporter toute interférence reçue, y compris des interférences qui peuvent provoquer un fonctionnement non désiré. Tout changement ou modification fait(e) à cet appareil et non expressément approuvé(e) par STMicroelectronics peut annuler l’autorisation pour l’utilisateur de faire fonctionner l’appareil. Approbation du module IC: 8976C-SPWFS04 Conformément à IC CNR-210, le module SPWF04SA/C est répertorié comme un dispositif émetteur modulaire Ce module n’est évalué que pour une utilisation autonome. Les produits finis incorporant plusieurs émetteurs doivent être conformes à la colocation et aux exigences d'exposition RF en concordance avec les procédures FCC multi-émetteurs. D’autres émetteurs fonctionnant dans des dispositifs portables exposés aux RF (par exemple, situés à moins de 20 cm des personnes avec dispositifs portatifs ou portés contre le corps) peuvent nécessiter d'une approbation séparée. A.2.1 Instructions d'étiquetage Lors de l'intégration du module SPWF04SA/C dans le produit final, le fabricant doit s’assurer que les exigences en matière d'étiquetage de la IC sont satisfaites . Une déclaration doit être placée sur l’étiquette extérieure du produit final indiquant que le produit comprend un module certifié. L'étiquette doit comporter les informations suivantes (ou une mention analogue que recouvre la même notion): Contient IC ID: 8976C-SPWFS04 OU Ce produit contient IC ID: 8976C-SPWFS04 Le sous-traitant doit inclure les énoncés suivants sur l’étiquette extérieure du produit final à moins que le produit ne soit trop petit (par exemple moins de 4 x 4 pouces): Cet appareil est en conformité aux normes IC. L’utilisation est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences nocives, et (2) Cet appareil doit supporter toute interférence reçue, y compris des interférences qui peuvent provoquer un fonctionnement non désiré Regulatory compliance A.2.2 SPWF04SA, SPWF04SC Instructions pour l’utilisation du produit La présente section concerne les produits finis contenant le module SPWF04SA/C, assujettis aux normes IC. Le manuel du produit final doit contenir la déclaration suivante (ou une mention analogue que recouvre la même notion): “Avertissement: Les changements ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'autorisation de l'utilisateur de faire fonctionner cet équipement. (CNR-210)” Dans le cas où le produit finis d’un fabriquant OEM rentre dans les limites de la Classe B (résidentiel), les énoncés suivants doivent être inclus dans le manuel du produit finis: “ Remarque : Cet équipement a été testé et déclaré conforme aux limitations prévues dans le cadre de la classe B des appareils numériques, définies par la norme CNR-210 d'Industrie Canada. Regulatory compliance SPWF04SA, SPWF04SC Ces limites sont conçues pour fournir une protection raisonnable contre toute interférence dangereuse issue d'une installation résidentielle. Cet équipement produit, utilise et peut émettre de l'énergie radio électrique et, s'il n'est pas installé et utilisé conformément aux présentes instructions, peut causer des interférences nuisibles aux communications radio. Cependant, il se peut que des interférences se produisent dans une installation particulière. Si cet appareil cause des interférences nuisibles à la réception des signaux de radio ou de télévision, ce qui peut être déterminé en allumant et en éteignant l'appareil, nous encourageons l'utilisateur à essayer de corriger ces interférences par l'un des moyens suivants: – Réorienter ou repositionner l'antenne de réception. – Augmenter la distance séparant l’équipement du récepteur. – Connecter l’équipement à une prise appartenant à un circuit différent de celui sur lequel le récepteur est connecté. – Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.” Dans le cas où le produit finis d’un fabriquant OEM rentre dans le cadre des limites imposées aux appareils numériques de classe A, les énoncés suivants doivent être inclus dans le manuel du produit finis: “ REMARQUE: Cet appareil a été testé et certifié conforme aux spécifications d'un appareil électronique de classe A (class A digital device), conformément à la norme CNR-210 d'Industrie Canada. Ces contraintes sont destinées à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est utilisé dans une installation commerciale. Cet équipement produit, utilise et peut émettre de l'énergie radio électrique et, s'il n'est pas installé et utilisé conformément aux présentes instructions, peut causer des interférences nuisibles aux communications radio. L'utilisation de cet appareil dans une installation résidentielle peut entraîner des interférences nuisibles et l'utilisateur devra corriger les interférences à ses propres frais.” A.3 Certification CE Le module SPWF04SA/C a obtenu une certification de conformité aux normes suivantes: – EN 300 328 V1.8.1 :2012 – EN 300 328 V1.9.1 :2015 – EN 301 489-17 V2.2.1 :2009 – EN 301 489-1 V1.9.2:2011 – EN 62479 :2010 – EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2 :2013 Le module est certifié CE: Regulatory compliance A1 SPWF04SA, SPWF04SC SPWF04SA, SPWF04SC 10 Revision history Revision history Table 9. Document revision history Date Revision 27-Apr-2016 Changes Initial release. – DocID025635 Rev 7 17/18 SPWF04SA, SPWF04SC IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 18/18 DocID025635 Rev 7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 25 Language : it-IT Title : Serial-to-Wi-Fi b/g/n intelligent modules Author : STMICROELECTRONICS Subject : - Keywords : Technical Literature, 025635, Product Development, Specification, Datasheet, SPWF01SA, SPWF01SC Creator : Microsoft® Office Word 2007 Create Date : 2016:06:10 12:11:21+02:00 Modify Date : 2016:06:10 12:11:21+02:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools