ST Microelectronics S R L ZB260A ZigBee Module User Manual SPZB260

Download:
Mirror Download [FCC.gov]
Document ID	859653
Application ID	VvpdG+U50TZxrl/1yYm0Bg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.81kB (322597 bits)
Date Submitted	2007-10-25 00:00:00
Date Available	2007-10-25 00:00:00
Creation Date	2005-10-20 10:47:30
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2007-09-21 15:10:01
Document Title	SPZB260.fm
Document Creator	FrameMaker 7.2
Document Author:	antonio zizzo-uni

SPZB260
ZigBee module
Features
■
Integrated 2.4GHz ,IEEE 802,15,4-compliant
transceiver:
– 0 dBm nominal TX output power
– -92 dBm RX sensitivity
– + 2 dBm in boost mode
– RX filtering for co-existence with IEEE
802.11g and Bluetooth devices
– Integrated VCO and loop filter
■
Integrated IEEE 802.15.4 PHY and MAC
■
Controlled by a Standard Serial Line for an
easy interface of host microcontrollers (SPI)
Description
■
Embedded flash and integrated RAM for
program and data storage
■
On board 24 MHz stable Xtal
SPZB260 is a low power consumption ZigBee
module optimized for embedded applications. It
enables OEMs to easily add wireless capability to
electronic devices.
■
Integrated RC oscillator ( typ 10KHz) for low
power operation
■
1 µA power consumption in Deep sleep mode
■
Watchdog timer and power on reset
■
Pins available for Non-intrusive debug
interface (SIF)
■
Single supply voltage 2.1 to 3.6 Vdc.
■
Available Link and Activity outputs for external
■
Indication / monitor
■
CE compliant
■
FCC compliant ( FCC ID:S9NZB260A )
Applications
■
Industrial controls
■
Sensor networking
■
Monitoring of remote systems
■
Home applications
■
Security systems
■
Lighting controls
September 2007
The module is based on SN260 ZigBee Network
Processor which integrates a 2.4GHz, IEEE
802.15.4-compliant transceiver as well as IEEE
802.15.4 PHY and MAC.
24 MHz high stability Xtal is available aboard the
module to perform the timing requirements as per
ZigBee specifications.
A single supply voltage is requested to power the
module. An integrated 2.5 GHz specific Murata
antenna is aboard. The voltage supply also
determines the I/O ports level allowing an easy
interface with the host system.
The module is controlled by means of a standard
serial interface (SPI) allowing the connections to a
variety of Host microcontrollers.
( for other information and details, please refer to
SN260 Datasheet available at www.st.com )
Rev 1
1/14
www.st.com
14
Contents
SPZB260
Contents
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2
Operating ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1
DC electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2
DC I/O specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.3
RF electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mechanical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Appendix A FCC statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2/14
A.1
Label instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A.2
Special requirement for Modular application . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SPZB260
Block diagram
Block diagram
Figure 1.
Block diagram
Vdd
24 MHz
XTAL
SIF
SN 260
Tranceiver
SPI
RF
antenna
Balun
Filter
CONTR SIGN
Pin settings
2.1
Pin connections
Figure 2.
Pin connection diagram
3/14
Pin settings
2.2
SPZB260
Pin description
Table 1.
4/14
Pin description
Pin n
Pin name
Direction
Description
RSTB
Active low reset ( an internal pull-up of 30 kohm typ is provided)
HOST_INT
Host Interrupt Signal ( from ZB Module to Host)
SPI_SSEL
SPI Slave Select ( from Host to ZB Module)
SPI MOSI
SPI Data , Master Out / Slave In ( from host to ZB Module)
SPI MISO
SPI Data , Master In / Slave Out ( from ZB Module to host)
SPI_CLK
SPI clock
GND
---
Ground
VDD
---
Input power supply
SIF_CLK
Non-intrusive debug Interface
Serial interface Clock Signal ( internal pulldown)
10
SIF_MISO
Non-intrusive debug Interface
Serial interface Master IN/ Slave Out
Non-intrusive debug Interface
Serial interface Master Out/ Slave In
To guarantee a proper signal level when in deep sleep mode
connect a 10kΩ resistor to GND
11
SIF_MOSI
12
SIF_LOADB
I/O
Non-intrusive debug Interface
Serial interface Load strobe ( Open collector with internal pull-up)
To improve noise immunity connect a 10kΩ resistor to VDD
13
PTI_EN
Frame Signal of Packet Trace Interface (PTI)
14
PTI_DATA
Data Signal of Packet Trace Interface (PTI)
15
WAKE
Wake Interrupt Signal from Host to ZB Module
16
ACTIVITY
Activity signal for application debug /monitor
17
SDBG
SPZB260
Maximum ratings
Maximum ratings
3.1
Absolute maximum ratings
Table 2.
Absolute maximum ratings
Values
Symbol
3.2
Parameter
Unit
Min
Max
VDD
Module supply voltage
-0.3
3.6
VIN
Input voltage on any digital pin
-0.3
Vdd+0.3
Tstg
Storage temperature
-40
+85
°C
Tsold
Soldering temperature < 10s
240
Operating ranges
Table 3.
Operating ranges
Values
Symbol
Parameter
VDD
Module supply voltage
Tstg
Operating ambient
temperature
Conditions
- 20°C < T < 70 °C
Unit
Min
Typ
Max
2.1
3.3
3.6
+70
°C
-20
5/14
Electrical characteristics
SPZB260
Electrical characteristics
4.1
DC electrical characteristics
Table 4.
DC electrical characteristics
Values
Symbol
Parameter
Conditions
Unit
Min
Typ
Max
IRX
RX current ( boost mode)
Vdd = 3.0 V, T = 25 °C
38
mA
IRX
RX current ( normal mode) Vdd = 3.0 V, T = 25 °C
36
mA
ITX
TX current ( boost mode)
Vdd = 3.0 V, T = 25 °C
42
mA
ITX
TX current (normal mode)
Vdd = 3.0 V, T = 25 °C
36
mA
IDS
Deep sleep current
2.1 < Vdd < 3.6 V
T = 25°C
4.2
DC I/O specification
Table 5.
DC Input / Output specification
µA
Values
Symbol
Parameter
Conditions
Unit
Min
VIL
Low Level Input Voltage
2.1 < Vdd < 3.6 V
VIH
High level input voltage
Iil
Iih
Typ
Max
0.2 x Vdd
2.1 < Vdd < 3.6 V 0.8 x Vdd
Vdd
Input current for logic 0
2.1 < Vdd < 3.6 V
-0.5
mA
Input current for logic 1
2.1 < Vdd < 3.6 V
0.5
mA
Ripu
Input pull-up resistor
30
kΩ
Ripd
Input pull-down resistor
30
kΩ
VOL
Low level output voltage
0.18 x Vdd
VOH
High level output voltage
0.82 x Vdd
Vdd
IOHS
Output source current
mA
IOLS
Output sink current
mA
IOHH
Output source current (pin 15,16,17)
mA
IOLH
Output sink current (pin 15,16,17)
mA
IOTot
Total output current for I/O
40
mA
6/14
SPZB260
4.3
Electrical characteristics
RF electrical characteristics
Table 6.
RF electrical characteristics
Values
Symbol
Parameter
Conditions
Unit
Min
Frequency range
2.1 < Vdd < 3.6 V
Typ
2405
2480
TX
Output power
RX
Sensitivity
Vdd = 3.0V, 1% PER
Carrier frequency error
Vdd=3.0V -20 / + 70 °C
Error Vector magnitude
Normal / boost mode
15
Adjacent channel rejection
+/- 5 MHz
+/- 10 MHZ
35
40
CFE
Max
MHz
dBm
-92
dBm
-40
40
ppm
25
dBm
7/14
Mechanical dimensions
SPZB260
Mechanical dimensions
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect . The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
Figure 3.
8/14
Mechanical dimensions
SPZB260
Mechanical dimensions
Figure 4.
Solder pad layout
9/14
FCC statement
SPZB260
Appendix A
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
●
Reorient or relocate the receiving antenna
●
Increase the separation between the equipment and receiver
●
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Antenna
Our module type SPZB260 is for OEM integrations only. The end-user product will be
professionally installed in such a manner that only the authorized antennas are used.
Caution
Any changes or modifications not expressed approved by the part responsible for
compliance could cause the module to cease to comply with FCC rules part 15, and thus
void the user’s authority to operate the equipment.
10/14
SPZB260
A.1
FCC statement
Label instruction
Instruction manual for FCC ID labeling
Module type:
ZigBee module
FCC-ID:
S9NZB260A
SPZB260
This intends to inform you how to specify the FCC ID of our ZigBee module SPZB260 on
your final product.
Based on the Public Notice from FCC, the product into which our transmitter module is
installed must display a label referring to the enclosed module.
The label should use wording such as “Contains Transmitter module FCC ID: S9NZB260A
or “Contains FCC ID: S9NZB260A , any similar wording that expressed the same meaning
may be use.
It shows an example below
Contains FCC ID: S9NZB260A
A.2
Special requirement for Modular application
The following requirements are fulfilled:
1.
The modular transmitter must have its own RF shielding:
The RF module used on the board fulfils the emission requirements of the FCC rules
without additional shielding.
2.
The modular transmitter must have buffered modulation/data inputs:
The module has a memory management unit inside of the IC. The processor
interfacing with the external application by means general purpose I/O ( GPIO) , Uart,
SPI. The processor interfaces also the RF part of the module exchanging data and
command with it. Inside the processor a flash memory is available to download the
customer application and the ZigBee profiles.
3.
The modular transmitter must have its own power supply regulation:
The IC contains an own voltage regulation. In case of changes in the supply voltage
VCC (for example caused by temperature changes or other effects), the internal
voltage will be stabilized.
4.
The modular transmitter must comply with the antenna requirements of Section 15.203
and 15.204:
The RF module is for OEM (Original Equipment Manufacturer) integration only. The
end-user product will be professionally installed in such a manner that only the
authorized antenna is used.
5.
The modular transmitter must be tested in a stand-alone configuration:
The RF module was tested in a stand-alone configuration.
6.
The modular transmitter must be labelled with its own FCC ID number:
The RF module will be labelled with its own FCC ID number. When the module is
installed inside the end-product, the label is not visible. The OEM manufacturer is
instructed how to apply the exterior label.
11/14
FCC statement
SPZB260
7.
The modular transmitter must comply with any specific rule or operating requirements
applicable to the transmitter and the manufacturer must provide adequate instructions
along with the module to explain any such requirements:
The EUT is compliant with all applicable FCC rules. Detail instructions are given in the
product Users Guide.
8.
The modular transmitter must comply with any applicable RF exposure requirements.
●
Maximum measured power output: 3,08 mW
●
Maximum antenna gain: 0,6 dBi = numeric gain 1,148 (see also FCC test report)
Maximum permissible exposure defined in 47 CFR 1.1310: 1 mW/cm².
The RF module operates at low power level so it does not exceed the Commission’s RF
exposure guidelines limits; furthermore, Spread spectrum transmitters operate according to
the Section 15.247 are categorically excluded from routine environmental evaluation.
12/14
SPZB260
Revision history
Revision history
Table 7.
Document revision history
Date
Revision
07-Sep-2007
Changes
First release
13/14
SPZB260
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
14/14

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 14
Page Mode                       : UseOutlines
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:e43319b9-bbf8-4a88-9752-7ab5049d9868
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : FrameMaker 7.2
Modify Date                     : 2007:09:21 15:10:01Z
Create Date                     : 2005:10:20 10:47:30Z
Document ID                     : uuid:5bd9b5a4-a90c-462d-ac0f-7f31d7956e53
Format                          : application/pdf
Title                           : SPZB260.fm
Creator                         : antonio zizzo-uni
Author                          : antonio zizzo-uni

EXIF Metadata provided by EXIF.tools