STL WP-2 Wireless Pendant User Manual WP2 Instrux

Download:
Mirror Download [FCC.gov]
Document ID	445646
Application ID	Z2LX33aWp0qs4FtqeoNFtA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.32kB (16527 bits)
Date Submitted	2004-07-01 00:00:00
Date Available	2004-06-29 00:00:00
Creation Date	2004-05-28 11:58:31
Producing Software	Acrobat PDFWriter 3.03 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	WP2 Instrux.PDF
Document Creator	Corel VENTURA 8 - [WP2 Instrux]

Wireless Pendant™ WP-2
Operating Instructions
NOTE: The Pendant is water-resistant, that is, it can withstand
limited exposure to liquids. However, it is not waterproof,
and should not be immersed in any liquid.
Universal Medical Products’ Wireless Pendant™ can be used in
place of or along with a Transmitter (model WT-2) in the UMP
Wireless Sentry™ monitoring system to send an emergency alarm
signal to the Receiver (model WR-3 or WR-4). It can be worn either
around the neck or on the wrist. It operates on three LR44 1.5V
button cell batteries (included). On Standby status, these batteries
will last for approximately 3 years. We recommend that you test the
Pendant periodically to be sure the batteries are working. If the
communication distance or the brightness of the alarm LED is
reduced, replace all three batteries with new ones.
To replace batteries
1. Remove the two screws on the back of the Pendant and lift
off the front of the casing.
2. Pry out the old batteries with a pen or small screwdriver.
3. Place the new batteries into position, being sure to align the
polarities correctly. Match the “+”sign on the batteries with
the “+”marked in the battery compartment.
4. Before screwing the front of the unit back into place, press
the blue circle to be sure the batteries have been installed
correctly and are operational. The LED should go on.
5. Reprogram the device if necessary (see below).
Programming
The Pendant can activate the Receiver after being programmed
as described below:
1. Press and hold the PROGRAM button of the Receiver until
the green PROGRAM LED lights up. The LED indicating
the first empty station location will flash.
2. Press the PROGRAM button to select the desired empty
location. The LED of each empty station will light up in turn
each time the button is pushed.
3. Press and hold the ALARM button (blue circle) on the
Pendant until you hear a long beep from the Receiver and
the station LED stops flashing.
4. Press the PROGRAM button to program the next empty
station,
OR
Press CONFIRM on the Receiver to return to normal
monitor mode.
Operation
In an emergency, the Receiver can be activated using the Pendant.
Pressing the ALARM button once will transmit the alarm signal to
the Receiver for approximately 3 minutes. The alarm sound on the
Receiver will be activated. The LED on the Pendant will flash to help
the caregiver identify the source of the alarm signal.
To stop the alarm sound on the Receiver, press the ALARM RESET
button on the Receiver. The corresponding location LED will also go
off. The Pendant will be disabled for about 6 seconds after sending
the alarm signal. After this time, the Pendant will reset itself
automatically and can then be used again.
For more details on the operation of the Wireless Sentry system,
see the Operator’s Manual included with the Receiver.
FCC Warning
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
Radio Frequency Interference
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that on which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
UNIVERSAL MEDICAL PRODUCTS, INC., guarantees the quality
and workmanship of the Wireless Sentry™ Receiver and each
Transmitter (including Pendant) and Charger for a period of one (1)
year from date of purchase. This warranty is in force provided there
is no evidence of misuse or improper installation.
Under the conditions of this warranty, UNIVERSAL MEDICAL
PRODUCTS, INC., agrees to repair and return any defective or
inoperative Wireless Sentry™ units, components, or parts within 30
days without charge.
Units, components or parts that are determined not to be covered by
this warranty because of time, abuse/misuse, or improper
installation, will be repaired or replaced on an established cost
repair basis within 30 days.
UNIVERSAL MEDICAL PRODUCTS, INC., DOES NOT CLAIM
THAT THE WIRELESS SENTRY™ SYSTEM WILL PREVENT
BED- AND CHAIR-RELATED FALLS WITHOUT FAIL. IT DOES
CLAIM THAT, WITH A COORDINATED EFFORT FROM THE
INSTITUTION NURSING STAFF AND AN ACCEPTABLE FALLS
PREVENTION PROGRAM, THE WIRELESS SENTRY™ SYSTEM
CAN HELP TO REDUCE THE NUMBER OF FALLS THAT OCCUR
WITHIN AN INSTITUTION.
All questions or inquiries should be directed to:
UNIVERSAL MEDICAL PRODUCTS, INC.
th
1620 N. 20 Circle
Lincoln, NE 68503-1103
Tel.: (888) 716-0077 (Toll Free) or (718) 499-0020
Fax: (732) 583-6923 or (718) 499-6494
Printed in China

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 4
Creator                         : Corel VENTURA 8 - [WP2 Instrux]
Create Date                     : 2004:05:28 11:58:31
Title                           : WP2 Instrux.PDF
Author                          : 
Producer                        : Acrobat PDFWriter 3.03 for Windows NT
Subject                         : 

EXIF Metadata provided by EXIF.tools