SZ DJI TECHNOLOGY HG8001501 RONIN-M User Manual 5

SZ DJI TECHNOLOGY CO., LTD RONIN-M 5

User Manual 5

Ronin-M User Manual© 2015 DJI. All Rights Reserved. 31Remote Control FeaturesMODE: The MODE switch is used for toggling SmoothTrack. 1. In Position 1, Smooth Track is off. Remote control is freely position pan axis stops and holds the last input position of the pan axis control stick.2. In Position 2, Smooth Track is on. Remote control is freely position pan axis stops and holds the last input position of the pan axis control stick.3. In Position 3, Smooth Track is on. The gimbal will always point and reset pan to the forward facing direction once the pan axis control stick is let go.Position 1 -Free, SmoothTrack Off Position 2 -Free, SmoothTrack On Position3 -Reset to Center, SmoothTrack OnFUNCTION: 1. The FUNCTION switch is used to select the SmoothTrack speed. There are 3 possible selections: Fast, Normal and Slow. The value of each speed can be preset in the App or PC Assistant.Position 1 -Fast Position 2 -Normal Position3 -Slow2. Activating Motor Kill SwitchQuickly ip the FUNCTION Switch between Position 1 and Position 3 consecutively for 3 times and you will activate the motor kill switch. Do the same again to turn off the motor kill switch. Prior to re-activating the gimbal motors, be sure to position the camera in the standard operating position. The motor kill switch is useful in case the gimbal operator runs into an issue or you need to make a quick mechanical adjustment to the gimbal or camera setup.Left Stick: Horizontal movements on the left stick control the Roll axis. Vertical movements have no denition.Right Stick: Horizontal movements on the right stick control the Pan axis.Right Stick:Vertical movements on the right stick control the Tilt axis.These stick settings can be customized in the DJI Ronin-M Assistant App or PC Assistant.Adding3rdpartytransmitter/receiverRonin-M supports 3rd party transmitters/receivers, such as D-Bus or PPM. Connect the transmitter through the port (refer to Page 8 for the location of D-Bus/PPM port).
32 © 2015 DJI. All Rights Reserved. Operation ModesThere are three operation modes in the Ronin-M: underslung mode, upright mode and briefcase mode.Underslung ModeUnderslung mode is the standard, default mode. It can be used without any user input.Upright ModeFlip the gimbal forward 180 degrees and it will automatically change to upright mode. Alternatively, you can set the gimbal into upright mode before turning it on. Upright mode is ideal for car mounts or other high camera positions, as it allows you to shoot higher and/or at eye level. Upright mode can be used without any user input. Do not ip the gimbal over sideways going left or right to convert to upright mode.
Ronin-M User Manual© 2015 DJI. All Rights Reserved. 33Briefcase ModeBriefcase mode allows you to hold the Ronin-M in a slim prole close to your body. To enter briefcase mode, tilt the gimbal on the roll axis 90 degrees to the left or right. You may turn briefcase mode off in the gimbal app, in which case the Ronin-M will never automatically transform into briefcase mode. In briefcase mode, the remote control does not have pan, tilt, or roll control of the Ronin-M. MaintenanceThe gure to the right shows the proper way to transport the Ronin-M with the stand. Using the hook-and-loop straps, lock the Ronin-M gimbal in place as shown. Be sure to undo the straps prior to turning the Ronin-M on! Ronin-M is a precise machine, and it is not waterproof. Keep it away from sand and dust during usage. After use, it is recommended to wipe the Ronin-M down with a soft dry cloth. Never spray any cleaning liquids onto the Ronin-M.
34 © 2015 DJI. All Rights Reserved. TroubleshootingNO. The Problem What to Do1Motors appear to be weak After camera balancing, launch the Assistant App or the PC/MAC Assistant and start the Auto Tune Stability. Wait for the process to complete and the stiffness settings will be populated on the screen. 2If after tapping the Auto Tune Stability button and the gimbal is still vibrating(1) Check to make sure all knobs are very tight. Including the pan motor knob.(2) Check to make sure the camera securing screw is tight. Push on the camera plate to make sure it is not loose and sliding in the camera mount.(3) Try decreasing the stiffness of the each axis. You should be able to tell if there is one particular axis being affected by looking at the "power" of the axes.3Pan axis seems off center Go into the Assistant App or PC/MAC Assistant, tap/click the Calibrate Center and follow the on-screen instructions. 4Ronin seems to be drifting Place the Ronin-M on the tuning stand and in the Assistant App or the PC/MAC Assistant, tap/click the Calibrate System button. Let the process complete before picking up the Ronin-M.5SmoothTrack doesn’t work (1) Turn on the Remote control and be sure the MODE switch is not at Position 1 (the uppermost position).(2) SmoothTrack is turned off in the Assistant App or the PC/MAC Assistant software.(3) The SmoothTrack Deadband is turned up too high. Reduce the Deadband size in the SmoothTrack Menu.6Motors seem to shutoff automaticallyCheck your camera balance. If the power indicated in the Gimbal Motors Menu indicates 10 or more on any of the 3 axes, please rebalance your camera.7Gimbal shuts off and doesn’t come back onPower cycle the gimbal. This is a motor protection algorithm that’s built into the Ronin-M to save its own electronic components. If any particular motor goes into a self-protection mode (motor shuts off) 6 times within a 1 minute period, the Ronin-M will shut off power to the motors and will not come back to life unless power cycled.8Forgot the Bluetooth passwordConnect Ronin-M to the PC/MAC Assistant and click the "Reset Password" button to reset your password. 9Footage appears to wobble side to side or up and downSmoothTrack speed is too high or SmoothTrack deadband is too low. Decrease the SmoothTrack speed or increase the deadband.
© 2015 DJI. All Rights Reserved. 35SpecicationGeneralBuilt-In Functions Three Operation Modes Underslung Mode Upright ModeBriefcase Mode Built-in independent IMU module DJI Specialized Gimbal Drive Motors with Encoders Bluetooth Module USB Connection 2.4GHz Receiver Temperature Sensor DJI Advanced 32-Bit DSP Processor D-Bus/PPM Receiver SupportedPeripheralCamera Tray Dimensions Maximum depth at center of mass on camera base plate: 120mmMaximum height measured from top of camera base plate: 195mm Maximum width: 160mmAccessory Power Connections 12V regulated P-Tap x 2, USB 500mW x 1, DJI Lightbridge x 1 GCU Input Power 4S Ronin-M BatteryConnections 2.4GHz Remote Control, Bluetooth 4.0, USB 2.0PC/MAC Assistant Software RequirementsWindows XP SP3; Windows 7; Windows 8 (32 or 64 bit); Mac OS X 10.9 or aboveMobile Assistant Software RequirementsiOS version 6.1 or above Mobile Device; Android 4.3 or aboveMechanical & Electrical CharacteristicsWorking Current Static current: 300mA (@16V) Dynamic current: 600mA (@16V) Locked motor current: Max 10A (@16V)Operating Temperature -15oC ~ 50oC (-5oF ~ 120oF)Weight 2.3kg (5.07lbs) fully loaded with handlebar Gimbal Dimensions 500mm(W) x 210mm (D) x 420mm(H)Working PerformanceLoad Weight Capacity (Reference Value)2.5kg (5.5lbs)Control Angle Accuracy 0.02°Maximum Control Rotation SpeedPan axis: 90°/secTilt axis: 100°/secRoll axis: 30°/sec Mechanical Endpoint Range Pan axis control: 360°Tilt axis control: Up 105o to Down 165°Roll axis control: ± 110°Controlled Rotation Range Pan axis control: 360°Tilt axis control: Up 105° to Down 165°Roll axis control: ± 25°
User manual is subject to change without prior notice.http://www.dji.com/product/ronin-m/downloadYou may visit DJI ofcal website to obtain the latest version of user manual.© 2015 DJI. All Rights Reserved.
FCC statements: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada RSS exemptes de licence standard(s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil. The output power of this device is less than 20mW.The SAR test is not required.

Navigation menu