SZ DJI TECHNOLOGY HG800TX15 RONIN-M TX User Manual 6

SZ DJI TECHNOLOGY CO., LTD RONIN-M TX 6

User Manual 6

34
© 2015 DJI. All Rights Reserved.
Troubleshooting
NO. The Problem What to Do
1Motors appear to be weak After camera balancing, launch the Assistant App or the PC/
MAC Assistant and start the Auto Tune Stability. Wait for
the process to complete and the stiffness settings will be
populated on the screen.
2If after tapping the Auto
Tune Stability button and
the gimbal is still vibrating
(1) Check to make sure all knobs are very tight. Including the
pan motor knob.
(2) Check to make sure the camera securing screw is tight.
Push on the camera plate to make sure it is not loose and
sliding in the camera mount.
(3) Try decreasing the stiffness of the each axis. You should
be able to tell if there is one particular axis being affected
by looking at the "power" of the axes.
3Pan axis seems off center Go into the Assistant App or PC/MAC Assistant, tap/click the
Calibrate Center and follow the on-screen instructions.
4Ronin seems to be drifting Place the Ronin-M on the tuning stand and in the Assistant App
or the PC/MAC Assistant, tap/click the Calibrate System button.
Let the process complete before picking up the Ronin-M.
5SmoothTrack doesn’t work (1) Turn on the Remote control and be sure the MODE switch
is not at Position 1 (the uppermost position).
(2) SmoothTrack is turned off in the Assistant App or the PC/
MAC Assistant software.
(3) The SmoothTrack Deadband is turned up too high.
Reduce the Deadband size in the SmoothTrack Menu.
6Motors seem to shutoff
automatically
Check your camera balance. If the power indicated in the
Gimbal Motors Menu indicates 10 or more on any of the 3
axes, please rebalance your camera.
7Gimbal shuts off and
doesn’t come back on
Power cycle the gimbal. This is a motor protection algorithm
that’s built into the Ronin-M to save its own electronic
components. If any particular motor goes into a self-protection
mode (motor shuts off) 6 times within a 1 minute period, the
Ronin-M will shut off power to the motors and will not come
back to life unless power cycled.
8Forgot the Bluetooth
password
Connect Ronin-M to the PC/MAC Assistant and click the
"Reset Password" button to reset your password.
9Footage appears to
wobble side to side or up
and down
SmoothTrack speed is too high or SmoothTrack deadband
is too low. Decrease the SmoothTrack speed or increase the
deadband.
© 2015 DJI. All Rights Reserved.
35
Specication
General
Built-In Functions Three Operation Modes
Underslung Mode
Upright Mode
Briefcase Mode
Built-in independent IMU module
DJI Specialized Gimbal Drive
Motors with Encoders
Bluetooth Module
USB Connection
2.4GHz Receiver
Temperature Sensor
DJI Advanced 32-Bit DSP Processor
D-Bus/PPM Receiver Supported
Peripheral
Camera Tray Dimensions Maximum depth at center of mass on camera base plate: 120mm
Maximum height measured from top of camera base plate:
195mm Maximum width: 160mm
Accessory Power Connections 12V regulated P-Tap x 2, USB 500mW x 1, DJI Lightbridge x 1
GCU Input Power 4S Ronin-M Battery
Connections 2.4GHz Remote Control, Bluetooth 4.0, USB 2.0
PC/MAC Assistant Software
Requirements
Windows XP SP3; Windows 7; Windows 8 (32 or 64 bit); Mac OS X
10.9 or above
Mobile Assistant Software
Requirements
iOS version 6.1 or above Mobile Device; Android 4.3 or above
Mechanical & Electrical Characteristics
Working Current Static current: 300mA (@16V)
Dynamic current: 600mA (@16V)
Locked motor current: Max 10A (@16V)
Operating Temperature -15oC ~ 50oC (-5oF ~ 120oF)
Weight 2.3kg (5.07lbs) fully loaded with handlebar
Gimbal Dimensions 500mm(W) x 210mm (D) x 420mm(H)
Working Performance
Load Weight Capacity
(Reference Value)
2.5kg (5.5lbs)
Control Angle Accuracy 0.02°
Maximum Control Rotation
Speed
Pan axis: 90°/sec
Tilt axis: 100°/sec
Roll axis: 30°/sec
Mechanical Endpoint Range Pan axis control: 360°
Tilt axis control: Up 105o to Down 165°
Roll axis control: ± 110°
Controlled Rotation Range Pan axis control: 360°
Tilt axis control: Up 105° to Down 165°
Roll axis control: ± 25°
FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications or changes to this equipment. Such modifications or
changes could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS exemptes de licence standard(s).
Son fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne peut pas provoquer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un
mauvais fonctionnement de l'appareil.
For model: R-6: The output power of this device is less than 20mW.The SAR test is not required.
For model: RONIN M-TX: The SAR limit of USA/CA (FCC/IC) is 1.6 W/kg averaged over one gram
of tissue.
It has also been tested against this SAR limit.
The highest SAR value reported under this standard during product certification for use when
properly worn on the body is 0.41 W/kg (FCC) and 0.41W/kg(IC) .

Navigation menu