SZ DJI TECHNOLOGY M1P1607 Mavic Pro User Manual x

Download:
Mirror Download [FCC.gov]
Document ID	3146119
Application ID	n5mb413u5ZHFUpj3KIOrFg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	42.24kB (527987 bits)
Date Submitted	2016-09-25 00:00:00
Date Available	2017-03-21 00:00:00
Creation Date	2017-12-15 04:04:56
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-15 04:04:56
Document Title	Microsoft Word - user manual.docx
Document Creator	PScript5.dll Version 5.2
Document Author:	elena

User Manual
Setting Up Aircraft and Batteries
The arms of the aircraft is folded on its delivery. Follow the instructions below to unfold the arms of the aircraft.
Setting Up Aircraft
1.
Rotate anti‐clockwise to unfold front arms towards the nose of the aircraft.
2.
Rotate anti‐clockwise to unfold rear arms of the aircraft.
3. Unfold all propeller blades and ensure all blades are aligned.
4. Ensure the Intelligent Flight Battery securely attached to the aircraft. The Intelligent Flight
Battery must be fully charged on its first use.
Setting Up Remote Controller
Unfold the mobile holder clamps and adjust the position of the antennas.
1. Insert the mobile devices into the space between the two mobile holder clamps.
2. Push the mobile holder clamps against the mobile device to secure its position.
3.Connect your mobile device with the a USB cable. You may also connect the mobile device to
the charging port of the remote controller with the supplied multi‐purpose USB cable.
Aircraft Diagram
1.
2.
3.
4.
GPS
Obstacle Sensing System
Motor
Gimbal
5.
6.
7.
Front LED Indicator
Vision Positioning Sensors
Aircraft Status Indicator
8. Control Mode Switch
9. Camera Micro SD Card Slot
10. Linking Button
11. Camera Micro SD Card Slot
Remote Controller Diagram
[1] Antennas
Relays aircraft control and video signal.
[2] Power Button
Used to power on or off the remote controller
[3]Control Stick
Controls the orientation and movement of the aircraft.
[4] App Button
Gain quick access to the feature in the DJI GO app.
[5] Mobile Holder Clamp
Adjust its width to accommodate the mobile device.
[6] Intelligent Flight Pause Button
Press once to allow the aircraft to exit from TapFly, ActiveTrack and Advanced mode.
[7] Return Home (RTH) Button
Press and hold the button to initiate Return to Home (RTH).
[8] Remote Controller Status Screen
Display system status of the remote controller.
[9] USB Port
Connect to mobile device for running the DJI GO app.
[10] C2 Button
[11] Camera Settings Dial
Turn the dial to adjust camera settings. (Only functions when the remote controller is connected
to a mobile device running the DJI GO app. )
[12] Shutter Button
Press to take a photo. If burst mode is selected, the set number of photos will be taken with one
press.
[13] Video Recording Button
Press to start recording video. Press again to stop recording.
[14] Gimbal Dial
Use this dial to control the tilt of the gimbal.
[15] C1 Button
Press C1 button once to launch the DJI GO app from the mobile device.
[16] Lanyard Hole
Used to secure the position of your lanyard.
[17] Flight Mode Switch
Switch between P‐mode, S‐mode
[18] Charging Port
Connect to the supplied charging cable for charging the battery. Connect to the supplied
mulit‐purpose USB cable for accessing to mobile device.
Using Remote Controller
Remote controller comes with a rechargeable battery. The battery level is displayed on the
remote controller system status screen. Follow the steps below to power on the remote
controller:
1. Press once and release to check the current battery level.
2. Press and hold the Power Button to turn on the remote controller.
3. The remote controller will beep when it is turned on, in addition, the battery level is displayed
on the remote controller status screen.
4. Repeat Step 2 to turn off the remote controller.
Intelligent Flight Battery
Power on or off the Intelligent Flight Battery
Turning On: Press the Power Button once, then press again and hold for 2 seconds to turn on.
The Power LED will turn red and the remote controller system status screen will display the
current battery level.
Turning Off: Press the Power Button once, then press again and hold for 2 seconds to turn off.
Power level indicators turn off when it is power down.
Switch
Charging
1.Connect the Battery Charger to a power source (100‐240 V 50/60 Hz).
2.Connect one end of the charger to the Intelligent Flight Battery to the Battery Charger. If the
battery level is above 95%, turn on the battery before charging.
3.The Battery Level Indicator will display the current battery level as it is charging.
4.The Intelligent Flight Battery is fully charged when the Battery Level Indicators are all off.
Disconnect the Intelligent Flight Battery from the Battery Charger.
5.Air‐cool the Intelligent Flight Battery after each flight. Allow its temperature to drop to room
temperature before storing it for an extended period.
6. The charger will stop charging the battery if the battery cell’s temperature is not within the
operating range (0°C ~ 40°C ).
Powering on the Aircraft and Remote Controller
1. Unfold the front and rear arms and propellers.
2. Power on the remote controller follow by the Intelligent Flight Battery.
3. Launch the DJI GO app and enter the “Camera” view.
Starting and Stopping the Motors
Starting the Motors
Push both sticks to the bottom inner or outer corners to start the motors. Once the motors have started spinning, release both
sticks simultaneously.
Stopping the Motors
There are two methods to stop the motors. When the aircraft has landed, push the throttle down ① , then conduct the same
CSC that was used to start the motors, as described above . Motors will stop immediately. Release both sticks once the motors
stop. Method 2: When the aircraft has landed, push and hold the throttle down. The motors will stop after3
seconds.
Using Mobile Device for Aircraft Control
You may choose control the aircraft via the WiFi connection below the mobile device and the
aircraft. Follow the steps below to learn how to use the mobile devices to control your M1P
aircraft.
1. Power off the Intelligent Flight Battery then slide the Control Mode Switch to enable
controlling the aircraft through mobile device.
2. Power on the remote controller then power on the Intelligent Flight Battery.
3. Enable WiFi connection on the mobile device, select “DJI Aircraft” from WiFi network list,
and enter the default password “12341234”.
4. Launch DJI GO app from the mobile device and select “Camera” view. Connection is
established if live view from the camera is displayed on the screen.
5. Virtual control sticks are displayed on screen, use these sticks to maneuver the aircraft.
Specifications
Aircraft
Model
M1P
Weight gimbal excluded
737 g
Weight gimbal included
746 g
Max Ascent Speed
5 m/s
Max Descent Speed
3 m/s
Max Speed
18 m/s
19685 feet ( 6000 m ) ( Software altitude limit: 400
Max Service Ceiling Above
feet above take‐off point )
Sea Level
Max Flight Time
Approx. 25 minutes
Operating
Range
32° to 104° F ( 0° to 40° C )
Temperature
Satellite Systems
GPS/GLONASS
Gimbal
Controllable Range
Pitch: ‐ 90° to + 30°
Obstacle Sensing System
Obstacle Sensory Range
2 ‐ 49 feet ( 0.7 ‐ 15 m )
Operating Environment
Surface with clear pattern and adequate lighting ( lux > 15 )
Vision Positioning System
Altitude Range
Velocity Range ≤10 m/s ( 2 m above ground )
Altitude Range
0.3 meter ‐ 10 meter (0 ‐ 33 feet)
Operating Range
0.3 meter ‐ 10 meter (0 ‐ 33 feet)
Operating Environment
Surface with clear pattern and adequate lighting ( lux > 15 )
Camera
Sensor
1/2.3” Effective pixels:12 M
Lens
FOV ( Field Of View ) 94° 20 mm ( 35 mm format equivalent ) f/2.8
focus at ∞
ISO Range
100‐3200(video) 100‐1600(photo)
Electronic Shutter Speed
1/8 ‐ 1/8000 s
Max Image Size
4000×3000
Still Photography Mode
ingle shot
Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB)
Time‐lapse
HDR
Video Recording Modes
3/5 Bracketed frames at 0.7EV Bias
UHD: 4096×2160 4K 24 / 25p
3840×2160 4K 24 / 25 / 30p
2704×1520 2.7K
24 / 25 / 30p
FHD: 1920×1080
24 / 25 / 30 / 48 / 50 / 60 / 120p
HD: 1280×720
24 / 25 / 30 / 48 / 50 / 60p
Max. Bitrate Of Video Storage
60 Mbps
≤ 32 GB ；exFAT
Supported File Formtas
FAT32
Photo
JPEG，DNG
Video
MP4/MOV MPEG‐4 AVC/H.264
Supported SD Card Types
Micro SD
Max capacity: 64 GB. Class 10 or UHS‐1 rating required
Operating Temperature
32° to 104° F ( 0° to 40° C )
> 32 GB
RAW
Remote Controller
Operating Frequency
Max
Distance
2.400 ‐ 2.483 GHz
Transmission FCC: around 7 km ； CE: around 4 km
interference
Operating Temperate
32° to 104° F ( 0° to 40° C )
Unobstructed, free of
Battery
2970 mAh
Transmitter Power EIRP
FCC:
Operating Voltage
700 mA @3.7 V
30 dBm； CE: 19 dBm
Charger
Voltage
13.05 V
Rated Power
50 W
Intelligent Flight Battery
Capacity
3830 mAh
Voltage
11.4 V
Battery Type
LiPo 3S
Energy
43.6 Wh
Weight
around 235 g
Operating Temperature
32° to 104° F ( 0° to 40° C )
Max Charging Power
100 W
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure
Info
ormation
This M1P complies with FCC radiation
exp
posure limits set forth for an uncontrolled environm
ment.
In order to avoid
d the possibiility of exceeeding the FCC
C radio frequ
uency exposu
ure limits, hu
uman
proxximity to the antenna
shall not be less than
20cm du
uring normal operation.
IC RSSS Warning
This device comp
plies with Ind
dustry Canada licence‐exe
empt RSS stan
ndard (s). Op
peration is subject
to th
nd (2) this device
he following two conditio
ons: (1) this device
may not
n cause intterference, an
musst accept anyy interferencee,including in
nterference th
hat may causse undesired operation of
o the
device.
Le présent
appareil est confforme aux CN
NR d'Industriie Canada ap
pplicables au
ux appareils radio
exem
mpts de licence.
L'exp
ploitation estt autorisée au
ux deux conditions suivanttes:
(1) l''appareil ne doit
d pas produire de brouiillage, et
(2) l'utilisateur de
d l'appareill doit acceptter tout bro
ouillage radio
oélectrique ssubi, même si le
brou
uillage est sussceptible d'en
n comprometttre le fonctio
onnement.
IC Raadiation Expo
osure Statement:
This equipment complies wiith IC RF rad
diation exposure limits set
s forth forr an uncontrrolled
environment. This transmitter must not bee co‐located or operating in conjunctio
on with any other
anteenna or transmitter.
This M1P should be installed and operated with minim
mum distancee 20cm betweeen the radiaator&
yourr body.
Cet appareil est
confo
orme aux limiteesd'exposition de
d rayonnemen
nt RF IC établiesspour un enviro
onnement non contrôlé.
Cetémetteur ne doiit pas être co‐im
mplanté oufoncctionner en conjonction avec toute
autreanteenne ou transm
mett
eur.
M doit être in
nstallé et utilisééavec une distance minimale de
d 20cm entre leradiateur
& vo
otre corps.
Cet M1P
Any Changes or modification
ns not expresssly approved
d by the partty responsiblle for compliiance
could void the usser’s authority to operate the equipme
ent.
EU Compliance
Statement:
S DJI TECHNOLOGY CO., LTD. hereby declares that this device is in
SZ
com
mpliance with the essential requirements and other relevant provvisions of thee R&TTE Direcctive.
A co
opy of the EU Declaration of
o Conformityy is available online at ww
ww.dji.com/eu
uro‐complian
nce
addreess: DJI GmbH
H, Industrie Sttrasse. 12, 97
7618, Niederllauer, Germany
EU contact

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : elena
Create Date                     : 2016:08:31 15:46:41+08:00
Modify Date                     : 2016:09:22 13:44:31-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2016:09:22 13:44:31-07:00
Format                          : application/pdf
Title                           : Microsoft Word - user manual.docx
Creator                         : elena
Document ID                     : uuid:6494acac-69e5-4d74-b139-6508984975bc
Instance ID                     : uuid:f6280037-0b2a-421d-93bd-21c8938062d1
Page Count                      : 14

EXIF Metadata provided by EXIF.tools