SZ DJI TECHNOLOGY RMTX11510 RONIN-M User Manual UnEncrypted
SZ DJI TECHNOLOGY CO., LTD RONIN-M UnEncrypted
UserManual.wiki
>
SZ DJI TECHNOLOGY
>
RMTX11510 User Manual
>
User Manual Part 1
Contents
1.
User Manual Part 1
2.
User Manual Part 2
User Manual Part 1
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![© 2015 DJI. All Rights Reserved. 7Ronin-M DiagramGetting StartedDJI Intelligent BatteryBefore you start using your Ronin-M, be sure to charge the battery. The DJI Intelligent Battery was specially designed for the Ronin-M. It has a capacity of 1580mAh, a voltage of 14.4V, and a variety of three hours.DJI Intelligent Battery Charger[1] Top Handle Bar [3] Quick Release Mount[4] Pan Motor [8] Bind Button [10] DJI Intelligent Battery[11] Roll Motor [12] Tilt Motor[13] Fore and Aft Adjustment[14] Tilt Vertical Adjustment[15] Roll Adjustment[16] IMU Port [20] DJI Lightbridge Port (rear side)[21] GCU Port (rear side)[1][2][4][3][8][][5][6][][10][11][12][14][15][13][16][][18][][20][21]](https://usermanual.wiki/SZ-DJI-TECHNOLOGY/RMTX11510.User-Manual-Part-1/User-Guide-2819074-Page-7.png)
![Ronin-M User Manual© 2015 DJI. All Rights Reserved. 9Using the DJI Intelligent Battery[1] Battery Level Indicators Checking the battery level: When the DJI Intelligent Battery is turned off, pressing the battery power button once will display the current battery level.Powering on: When the DJI Intelligent Battery is turned off, press and hold the power button for 1 second to turn on the DJI Intelligent Battery.Powering off: When the DJI Intelligent Battery is turned on, press and hold the power button for 1 second to turn off the DJI Intelligent Battery. Tuning Stand You can use the tuning stand during setup, or to store the gimbal. The following steps show how to use the tuning stand. 1. Hold the stand in the upright position as shown in the picture below.2. Press the buttons [1] on the outsides of the lower legs and rotate the legs downwards, away from the stand. Then press the buttons [2] on the outsides of the upper support arms and pull them upwards, as shown. 3. The upper half of this tuning stand can be removed by loosening the knob on the rear of the stand [4]. When mounting this section to a C-stand, always be sure to check the balance of the stand so that [1][2][5][4][3][3][1][2])JHI-PX #BUUFSZ-FWFM](https://usermanual.wiki/SZ-DJI-TECHNOLOGY/RMTX11510.User-Manual-Part-1/User-Guide-2819074-Page-9.png)
![Ronin-M User Manual© 2015 DJI. All Rights Reserved. 15Advanced Roll AdjustmentIf additional roll adjustment is needed in cases where the camera itself is too light in comparison to the tilt motor assembly, advanced roll adjustment can be achieved by loosening the indicated screws and pushing the assembly to the right or left.[1] [2]Balancing and backwards. adjustments are required to achieve the proper balance.3. Tighten the side clamp to lock the camera and mounting plate in position. If properly balanced, the camera should be able to remain steady at any given tilt angle.(#!&)*+ Ronin-M is front heavy or rear heavy. Tighten the clamp after balancing is completed.](https://usermanual.wiki/SZ-DJI-TECHNOLOGY/RMTX11510.User-Manual-Part-1/User-Guide-2819074-Page-15.png)
