SZ DJI TECHNOLOGY ZT300G1604 DATALINK PRO 900 User Manual x
SZ DJI TECHNOLOGY CO., LTD DATALINK PRO 900 x
Users Manual
Disclaimer Thank you for purchasing the Datalink Pro hereinafter referred to as product . Read this disclaimer carefully before using this product. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. Please install and use this product in strict accordance with the User Manual. SZ DJI Technology Co., Ltd. and its affiliated companies assume no liability for damage s or injuries incurred directly or indirectly from using, installing or refitting this product improperly, including but not limited to using non‐designated accessories. DJI is the registered trademark of SZ DJI Technology Co., Ltd. abbreviated as DJI . Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. This product and manual are copyrighted by DJI with all rights reserved. No part of this product or manual shall be reproduced in any form without the prior written consent of or authorization from DJI. This disclaimer is produced in various languages. In the event of variance among different versions, the Chinese version shall prevail when the product in question is purchased in Mainland China, and the English version shall prevail when the product in question is purchased in any other region. Warnings Only use the Datalink Pro in the corresponding frequency band and in accordance with local laws and Ensure all modules are connected and the parameters are set correctly in DJI Assistant regulations. the Datalink Pro for the first time. when using DO NOT bend or fold the antennas excessively. Ensure the antennas for both the mobile station and the Base Station are unobstructed when used. Only use the Datalink Pro in an open environment free from radio interference. Only pair the Datalink Pro Base Station with a mobile station in the same frequency band. Note that the M Datalink Pro and M Datalink Pro are not compatible. When upgrading the firmware, toggle the ‐position switch to the COMBO_SW position, connect the To avoid interference, DO NOT use a two‐way transceiver or walkie‐talkie operating near the module to the PC, and then run DJI Assistant . band when operating the M Datalink Pro. MHz Only use genuine DJI parts or parts certified by DJI. Unauthorized parts or parts from non‐DJI‐certified manufacturers may cause system malfunctions and compromise safety. . Ensure the Datalink Pro and its components are free from contamination e.g. water, oil, soil and sand . Contents Disclaimer ..................................................................................................................................................................................................... Warnings ....................................................................................................................................................................................................... About............................................................................................................................................................................................................... Part Description * ...................................................................................................................................................................................... Installation and Connection .................................................................................................................................................................. Usage ............................................................................................................................................................................................................... Linking Procedures ......................................................................................................................................................................... Configuring Parameters Using the DJI Assistant ............................................................................................................. Using the DJI Ground Station ...................................................................................................................................................... Working Status LED ........................................................................................................................................................................ Appendix ....................................................................................................................................................................................................... Specifications ..................................................................................................................................................................................... Compliance Information ......................................................................................................................................................................... FCC Compliance Notice .................................................................................................................................................................. RF Exposure Information ............................................................................................................................................................. IC RSS Warning................................................................................................................................................................................ KCC Warning Message .................................................................................................................................................................. NCC Warning Message ................................................................................................................................................................. EU Compliance Statement .......................................................................................................................................................... About The Datalink Pro is used for wireless data transmission, including communication between the Mobile Station and Base Station. There are M and M versions to meet the requirements of different regions. The multi‐functional bidirectional transmission link is perfect for the DJI A flight control system, D‐RTK and Ground Station. Use frequency bands of near MHz and MHz to avoid radio interference with the DJI Lightbridge and remote controller. Support for multiple interfaces, such as USB, CAN and UART, offers additional connectivity. Part Description * Base Station Antenna Interface Linking Button B. Working Status Indicator to work at V long term . ‐pin Port B : Power DC V input CAN port with baud rate of Mbps. B : GND A : Power DC V input A : GND A : CAN‐H A : CAN‐L B : UART‐RX B : UART‐TX ‐position Switch C :UART_SW C :CAN_SW Mobile Station Base Station Antenna* bps, working in TTL level logic of . – . V compatible with V, but not recommended Micro USB A. UART port with baud rate up to USB_SW COMBO_SW Antenna Interface Linking Button Micro USB ‐pin Port Definition is the same as the Base Station ‐position Switch Definition is the same as the Base Station Working Status Indicator M Antenna M Antenna Mobile Station Antenna * M Antenna pcs for standby Accessories ‐pin Cable x M Antenna pcs for standby Micro USB Cable x Double‐sided tape *The M and M Datalink Pro use different antennas but have the same functions. Installation and Connection The following uses the M Datalink Pro, DJI Matrice illustrate a typical installation and connection. , D‐RTK and DJI Intelligent Flight Battery to Attach the Base Station antenna and install it on the D‐RTK Ground System’s base board with a screw included with the D‐RTK product . Then connect the Base Station and the D‐RTK Ground System via an ‐pin cable. Install the Mobile Station to the DJI Matrice with double‐sided tape. Attach the antennas to the Mobile Station and fix them to the landing gears with two clips. Then connect the Mobile Station and the D‐RTK Air System via an ‐pin cable. Notes: Be sure to toggle the ‐position switch to the UART_SW position if using the D‐RTK, otherwise the Refer to the D‐RTK Quick Start Guide for details if using the D‐RTK. D‐RTK may fail to receive data from the Datalink Pro. Usage Use the Datalink Pro in an open environment free from radio interference. Linking Procedures Base Station and Mobile Station are linked before leaving the factory. Note that frequency linking is required if any device is changed or added. Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Base Station. Hold the Base Station’s Linking Button for about Status LED blinks red and green alternatively. seconds to enter the linking mode with the Working Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Mobile Station. Hold the Mobile Station’s Linking Button for about seconds and wait for linking. The Base Station and Mobile Station will connect with each other if successfully linked. Follow procedures – to link other Mobile Stations to set up a single‐to‐multiple system. Configuring Parameters Using the DJI Assistant DJI Assistant should be used to upgrade the Datalink Pro. Full Duplex Mode and Broadcast Mode can be switched in DJI Assistant Download DJI Assistant from www.dji.com and install it on your computer. Toggle the ‐position switch to the COMBO_SW position, connect the Base Station to the computer with DJI Assistant launched, and then configure parameters according to the message prompts. . Configure the Mobile Station in the same way. If multiple Mobile Stations are used, you must configure each Mobile Station one by one. Notes: Power cycle the Datalink Pro, Flight Control System and D‐RTK after upgrading. Supports Windows or later or Mac OS X or later . Using the DJI Ground Station Ensure the A Flight Control System, Datalink Pro and D‐RTK are connected correctly before powering on. Connect the Base Station to the PC via a Micro USB cable, and then run the Ground Station. Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Base Station first. Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Mobile Station. Note: The DJI Ground Station supports up to five Air Systems in Full Duplex Mode. The ‐position switch should be set to the COMBO_SW position. Download the User Manual from www.dji.com to learn more. Refer to the DJI Ground Station User Manual for details if using the DJI Ground Station. Working Status LED LED Blinking Red Description Parameter error after powering on. If not resolved by power Blinking Purple cycling, contact your dealer. Connected to the Assistant successfully. Blinking Yellow Upgrading or preparing for upgrade. Second or connected device information is clear. Quickly Blinking Green for Solid Blue Solid Green Current system setting is saved Run mode changed successfully , Mobile Station: Working in Broadcast Mode. Base Station: Working in Broadcast Mode and receiving the data from Mobile Station. Mobile Station: Mobile Station connected correctly in Full Duplex Mode. Base Station: At least one Mobile Station connected to the Base Solid Red Station in Full Duplex Mode. Mobile Station: All Mobile Stations are disconnected in both Run Modes. Base Station: All Mobile Stations are disconnected in Full Duplex Blinking Red and Green Alternatively Blinking Yellow Twice Solid White for Second Appendix Specifications Mode. Linking in progress. ‐position switch is toggled successfully. Device is initializing, only displays when powering on. Type DATALINK PRO Outdoor/RF Line‐of‐Sight Range Approximately Performance Transmit Power China: Taiwan: Features Frequency Band MHz dBm Base Station: . W China: ‐ Taiwan: Antenna Options Supported Interfaces Supported DJI Products Max. ‐ ‐ CE: dBm Canada: 5dBm Australia: 5dBm bps Vertically polarized USB, UART, CAN DATALINK PRO FCC: 5dBm dBm Mobile Station: . South Korea: Serial Data Rate dBm South Korea: Power Consumption A , D‐RTK, Ground Station Japan: dBm Mobile Station: . Base Station: . W CE: FCC: 2‐ Canada: 2‐ Japan: . ‐ Australia: 5‐ Operating Temperature ° to ° to °F ° to °F ‐ °C ° to Storage Temperature ‐ Dimension without Antenna Base Station: mm x Weight without Antenna Base Station: Humidity Power Supply Voltage Max. Signal Current % to °C %, non‐condensing Mobile Station: Mobile Station: mm x mm x . mm . mm x . mm Base Station: DC V Transmitting Mobile Station: DC V mA Max. Current Receiving Signal mA mA Compliance Information FCC Compliance Notice This device complies with Part of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the anten nna shall not be b less than cm during norrmal operation n. IC RSSS Warning This device compllies with Industry Canada liicence‐exemptt RSS standard d s . Operatio on is subject to t the follow wing two cond ditions: th his device may y not cause intterference, and this device must accep pt any interrference,includ ding interference that may caause undesired d operation of the t device. Le présent appareil est conform me aux CNR d'IIndustrie Canaada applicabless aux appareills radio exemp pts de licen nce. L'exp ploitation est autorisée aux deux conditions suivantes: l'appareil ne do oit pas produirre de brouillage, et l'utilisateur dee l'appareil doit accepter tou ut brouillage radioélectriqu e subi, même si le brouillag ge est susceeptible d'en co ompromettre lee fonctionnement. IC Raadiation Expossure Statementt: This equipment co omplies with IC RF radiation n exposure lim mits set forth for f an uncontrrolled environment. This transmitter must not be co‐llocated or operating in conju unction with an ny other antenna or transmittter. This equipment should be installled and operatted with minim mum distance body y. cm between n the radiator& & your Any Changes or modifications not expressly approved by th he party respo onsible for com mpliance could d void the user’s authority y to operate th he equipment. KCC Warning Messaage 해 해당무선설비는 는 운용 중 전파혼신 가능성이 있으므 므로 인명안전 전과 관련된 서비스는 할 수 없습 습니다. 해당 무선설비는 는 운용 중 전파혼신 전 가능성 성이 있음 NCC Warning Message 低 率電波輻射性 性電機管理辦法 法 第十 十二條 經型式認 認證合格之低 率 率或變更原設計 計之特性及 第十 十四條 低 商號或使 使用者均不得擅 擅自變更頻率 大 率射 射頻電機之使用 用不得影響飛航 航安全及干擾合 合法通信 經發 發現有干擾現象 象時,應改善至 至無干 擾時 時方得繼續使用 用 或工 工業 率射頻電機,非經許可,公 公 能 前項合法通 通信,指依電信 信法規定作業之 之無線電通信 低 率射頻電 電機須忍受合法 法通信 科學及醫 醫療用電波輻射 射性電機設備之 之干擾 EU Compliance Stattement SZ DJI D TECHNOLO OGY CO., LTD. hereby declares that thiss device is in n compliance with the essential requ uirements and other relevantt provisions of the R&TTE Dirrective. A cop py of the EU Deeclaration of Conformity is av vailable onlinee at www.dji.co om/euro‐comp pliance EU contact address: DJI GmbH, Industrie Strasse. 制 造 商 地 址 服 , Niederlauer, Germany 深圳市大疆创新科技有限公 深圳市南山区高新南四道18 热线 创维半导体设计大厦西座14层 400-700-0303 Manufactured by: th floor, West Wing, Skyworth Semiconductor Design Building NO. District, Shenzhen, Guangdong, China Gaoxin South th Ave, Nanshan
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : elena Create Date : 2016:05:23 14:46:02+08:00 Modify Date : 2016:06:03 09:43:26-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Metadata Date : 2016:06:03 09:43:26-07:00 Format : application/pdf Title : Microsoft Word - user manual.docx Creator : elena Document ID : uuid:f735dce5-6942-4e73-977b-2cc1dc9e1033 Instance ID : uuid:fdaa05bf-5e6f-49d7-9f30-72fe2112fd07 Page Count : 11EXIF Metadata provided by EXIF.tools