Safety Instruments ILUVMYZ7 Viking Z Seven SCBA User Manual Avon Viking Z Seven6 07

International Safety Instruments, Inc. Viking Z Seven SCBA Avon Viking Z Seven6 07

Users Manual

COPYRIGHT 2007 AVON - ISI 1PREFACEWARNINGS, CAUTIONS AND NOTESPlease read all carefully.Failure to properly use and maintain thisproduct could result in injury or death.INTENTThis manual is intended to acquaint owners and users withthe operation of the VIKING Z SEVEN, CBRN models of Self-Contained Breathing Apparatus, and to provide importantsafety information and limitations. All information, illustrationsand specifications in this manual are based on the latestproduct information available at the time of printing. The rightis reserved to make changes at any time without notice.IMPORTANTALL PERSONNEL USING THIS APPARATUS SHALL BETHOROUGHLY TRAINED BY A QUALIFIED INSTRUCTORIN DONNING, OPERATION, INSPECTION AND EMERGEN-CY OPERATION.Equipment should be thoroughly INSPECTED, FUNCTION-ALLY checked and cleaned after EACH exposure to intenseheat or harsh chemicals. UNDER A KNOWN CBRN CON-TAMINATION EXPOSURE, proper DECONTAMINATIONAND DISPOSAL PROCEDURES MUST BE FOLLOWED inaccordance with local government instructions and/or proce-dures. IF CONTAMINATED WITH LIQUID CHEMICAL WAR-FARE AGENTS, DISPOSE OF THE SCBA AFTER DECON-TAMINATION.The VIKING SCBA is designed to be simple to use and easyto maintain and will operate for many years if properly main-tained and cleaned. The instructions for care and use givenin this manual must be read, understood and carefully fol-lowed before the apparatus is used.The procedures in this manual DO NOT render AVON-ISI lia-ble for any losses or injury arising from any actions based onuse of same.Spare parts and accessories are available through your localAVON-ISI authorized distributor. Service beyond the scope ofthis manual is not recommended. If a problem persists, theapparatus should be removed from service, tagged for repair,and forwarded to an AVON-ISI Certified Service Center or tothe AVON-ISI factory for evaluation and/or repair. Do notmark the unit with inks or paints, which might be flammable,or cover any approved labels, such as NIOSH labels.TRAININGAVON-ISI strongly recommends that the training programused be consistent with NFPA 1500, Standard on Fire De-partment Occupational Safety and Health Programs andNFPA 1852, Standards on Selection, Care, and Maintenanceof Open –Circuit SCBA’s. Training and servicing programsare available upon request. Please contact AVON-ISI or yourlocal distributor for further details.APPROVALSAll Viking Z SEVEN SCBA are CBRN certified and NIOSH ap-proved, meeting the NFPA 1981 Standard, 2007 Edition andthe NFPA 1982 Standard, 2007 Edition (when equipped withPASS) requirements.NIOSH/OSHA WARNINGSThe following warnings are given in accordance with accept-ed safety conventions and/or NIOSH/OSHA requirements,and apply to the use of breathing apparatus in general.HEALTH LIMITATIONS: Wearers of the SCBA should becertified medically fit prior to use. In addition, there are bothphysiological and psychological limitations which should beconsidered before using SCBA. They include, but are not lim-ited to:• Emphysema• Chronic obstructive pulmonary disease• Bronchial asthma• X-ray evidence of pneumonia• Evidence of reduced pulmonary function• Coronary artery disease• Severe or progressive hypertension• Epilepsy (grand mal or petit mal)• Pernicious anemia• Diabetes (insipidus or mellitus)• Breathing difficulties when wearing an SCBA• Claustrophobia or anxiety when wearing an SCBA• Abnormal EKG results from resting or stress tests• Punctured or ruptured ear drumWORKING TEMPERATURES: The VIKING SCBA is ap-proved for respiratory protection during entry into or escapefrom oxygen deficient atmospheres, gases, and vapors attemperatures above -25°F. When used below freezing, caremust be exercised to prevent moisture from entering the de-mand exhalation valve. The facemask should remain on thedocking hook when not in use. On the AirSwitch model, theslide should be stored in the up position when not in use. Forthe RDV demand valve, the RDV should be stored on thedocking station found on the waistbelt. This includes whencylinders are being changed.DURATION OF USE: Although the VIKING has been ap-proved as either a 30-minute, 45-minute, or 60-minute breath-ing apparatus, the wearer’s varying work rate, physical condi-tion and other factors could substantially shorten the actualusable duration of the unit.SCBA LIMITATIONS: An SCBA can only protect the wear-er’s respiratory system. Other protection may be neces-sary to avoid contamination through skin absorption. Ifthese types of materials are suspected, an effective full-body covering of impermeable material must be wornwith the SCBA. A universal Level A HazMat suit is avail-able for the VIKING SCBA from HazMat suit manufactur-ers.FACIAL HAIR: Facial hair or any other items which may in-terfere with the facemask-to-face seal, including the nosecup,or the operation of the exhalation valve, must not be allowed.These include beards, sideburns, mustaches, bangs, headcoverings, or anything else that may interfere with the correctseal of the facemask and/or nosecup to the face.
COPYRIGHT 2007 AVON - ISI2EYE WEAR: Eye glasses shall not be used when the templebars interfere with the proper seal of the facemask to theface. If a user must wear corrective lenses while wearing theSCBA, they can be mounted in the facemask using a speciallens mounting kit (AVON-ISI p/n 136003) available fromAVON-ISI or through your local AVON-ISI authorized distribu-tor.MANUAL BYPASS: In compliance with NIOSH requirements,the Viking SCBA has a manually operated bypass which pro-vides a continuous flow of air to the facemask when required,independent of normal operation of the regulator. The bypassis opened by turning the red knob on the AirSwitch 90 de-grees in the direction shown by the knob arrow. The RDV by-pass opens by turning towards the user. Use of the bypasswill shorten the duration of the SCBA.CAUTIONS AND LIMITATIONS FOR VIKINGZ SEVEN MODELD - Airline respirators can be used only when the respirators are suppliedwith respirable air meeting the requirements of CGA G-7.1 Grade D orhigher quality.E - Use only the pressure ranges and hose lengths specified in the User'sInstructions.I - Contains electrical parts which have not been evaluated as an ignitionsource in flammable or explosive atmospheres by MSHA/NIOSH.J - Failure to properly use and maintain this product could result in injuryor death.M - All approved respirators shall be selected, fitted, used and maintained inaccordance with MSHA, OSHA, and other applicable regulations.N - Never substitute, modify, add, or omit parts. Use only exact replacementparts in the configuration as specified by the manufacturer.O - Refer to User's Instructions and/or maintenance manuals for informationon use and maintenance of these respirators.S - Special or critical User's Instructions and/or specific use limitationsapply. Refer to User's Instructions before donning.CAUTIONS AND LIMITATIONS FOR VIKING Z SEVENMODEL WITH CBRN PROTECTION APPROVALI - Contains electrical parts which have not been evaluated as an ignitionsource in flammable or explosive atmospheres by MSHA/NIOSH.J- Failure to properly use and maintain this product could result in injuryor death.M - All approved respirators shall be selected, fitted, used and maintained inaccordance with MSHA, OSHA, and other applicable regulations.N - Never substitute, modify, add, or omit parts. Use only exact replacementparts in the configuration as specified by the manufacturer.O - Refer to User's Instructions and/or maintenance manuals for informationon use and maintenance of these respirators.S - Special or critical User's Instructions and/or specific use limitationsapply. Refer to User's Instructions before donning.Q - Use in conjunction with personal protective ensembles that provideappropriate levels of protection against dermal hazards.R - Some CBRN agents may not present immediate effects from exposure,but can result in delayed impairment, illness or death.T - Direct contact with CBRN agents requires proper handling of the SCBAafter each use and between multiple entries during the same use.Decontamination and disposal procedures must be followed. Ifcontaminated with liquid chemical warfare agents, dispose of the SCBAafter decontamination.U - The respirator should not be used beyond 6 hours after initial exposureto chemical warfare agents to avoid possibility of agent permeation.WARNINGONLY THOSE SCBA UNITS THAT DISPLAY THEBELOW LABEL ON THE BACKFRAME AT THE AT-TACHMENT OF THE CYLINDER SPOON ARE CERTI-FIED AS CBRN AGENT APPROVED.Note: If your department has both CBRN and non-CBRN ap-proved units, be sure to check the backframe for this labelprior to donning an SCBA when using in environments wherethere is the possibility of cbrn agents beingpresent. Failure to do so may result ininjury or death.AVON-ISI ALSO DISPLAYS THISCBRN LABEL ON THE FACEMASKOF CBRN AGENT APPROVEDUNITS. THE CBRN FACEMASK LA-BELS ARE LOCATED INSIDE THE VISOR ON BOTHTHE RIGHT AND LEFT LOWER CORNERS.ANY FACEMASK THAT DOES NOT HAVE THISABOVE LABEL ON THE INSIDE VISOR SHOULDNOT BE USED IN ENVIRONMENTS WHERE THEREIS THE POSSIBILITY OF CHEMICAL WARFAREAGENTS BEING PRESENT.FACEMASKS, BACKFRAMES, O-RINGS, AND SEALSON AN AVON-ISI CBRN APPROVED VIKING SCBAARE NOT COMPATIBLE WITH NON-CBRN AP-PROVED UNITS. DO NOT INTERCHANGE PARTSWHEN DOING REPAIRS OR MAINTENANCE. CON-SULT AVON-ISI CUSTOMER SERVICE FOR FUR-THER DETAILS ON CBRN APPROVED PARTS.S- SPECIAL OR CRITICAL USER’S INSTRUCTIONS• Special or critical User's Instructions and/or specific uselimitations apply. Refer to User's Instructions before donning.• Approved for respiratory protection during entry into or escape foroxygen deficient atmospheres, gases and vapors at temperatures above -25°F.• Approved only when compressed gas container is charged withair meeting the requirements of CGA G-7.1 Grade D or higherquality that has a dew point of -65°F or lower and a maximumparticulate level of 5 mg/m3 air.• The compressed gas container shall meet applicable DOTspecifications.• When used as a combination apparatus, only 20% of the servicepressure may be used on entry.
COPYRIGHT 2007 AVON - ISI 3All Viking Z SEVEN SCBA are NIOSH CBRN agent approved,NIOSH approved and NFPA 1981Standard, 2007 Editioncompliant. The Viking Z SEVEN features a heads-up display(HUD) that monitors cylinder pressure and an emergency RICconnector that is used to refill the air of a down fire fighter.The Viking Z SEVEN model has VAS (Voice AmplificationSystem) as a standard feature. Additional options of the ZSEVEN model include radio interface, voice activatedcommunications, integrated PASS with data logging, buddybreather, and airline. All Vikings are available with lightweight carbon cylinders in 30, 45 or 60 minute rateddurations.The AVON-ISI Viking Z SEVEN is a self-contained, open-cir-cuit, compressed-air breathing apparatus, which is approvedby the National Institute of Occupational Safety and Health(NIOSH) and certified compliant to NFPA 1981Standard onOpen-Circuit Self-Contained Breathing Apparatus for Fire andEmergency Service, 2007 Edition. Positive pressure insidethe facemask, both during inhalation and exhalation, ensuresthat any leakage due to improper fit or component failure willbe an outward flow of air.The Viking Z SEVEN SCBA consists of several major compo-nents described in the following paragraphs.1.1 FACEMASKThe AVON-ISI full facemask as-sembly has a two point pull-for-ward Nomex net harness with anoptically-corrected, double curvehigh-impact polycarbonate visor.The visor’s scratch-resistant coat-ing conforms to NFPA standards.The interior of the visor has a per-manent anti-fog coating. Thefacemask standard seal is high-strength butyl blend and has apatented blended shape whichfits the firefighter's helmet withoutreadjustment. A standard blackinner-mask nosecup reducesdead-air space and CO2 buildup. The facemask has CBRN la-bels affixed at both lower corners of the visor.1.0 DESCRIPTION OF VIKING Z SEVEN SCBAAn in-mask HUD is mount-ed to the inner-mask nose-cup. The mask display in-cludes five LEDs: red = ¼full, yellow = ½ full, 1stgreen = ¾ full, 2nd green =full, and the last elevatedyellow = low battery indica-tor. The HUD indicates re-maining cylinder pressureand provides the primaryend-of-service time alarm.The HUD can also provideadditional status indicatorsdepending upon the op-tions ordered.1.2 AIRSWITCH® REGULATORThe patented AirSwitch second stage regulator is incorporat-ed into the facemask and combines the demand and exhala-tion valves to greatly reduce breathing resistance. This alsoallows for a longer duration of cylinder use. A speech dia-phragm provides excellent clarity and voice reproductionwhile incorporating the exhalation valve.The AirSwitch features a fresh air mode which allows usersto go from cylinder air to outside air by depressing the twocontrol slide tabs inward and then raising the slide upwardsfully. Push down for cylinder or supplied air. The AirSwitchshould stay open prior to donning and doffing of the VIKINGSCBA. The AirSwitch is made of high performance engi-neered plastics and incorporates a true manual bypass con-trol for emergency use.S- SPECIAL OR CRITICAL USER’S INSTRUCTIONS,CONTINUED• This approval applies only when the device is supplied withrespirable breathing air through 6 to 300 feet of hose at airpressures between 80 to 120 pounds per square inch gauge orfrom self contained air supply.Note: Viking CBRN SCBAs are not approved for supplied air usein confirmed or potential CBRN environments.• If the supplied air fails, open the cylinder valve, unplug supply airand proceed to fresh air immediately.• Use adequate skin protection when worn in gases and vaporsthat poison by absorption (example: hydrocyanic-acid gas).yellow(low battery)greenyellowredDOWN FOR SUPPLIED AIRUP FOR AMBIENT AIR
COPYRIGHT 2007 AVON - ISI41.3 REMOVABLE DEMAND VALVE (RDV) REGULATORThe Viking RDV regulator is a mask mounted second stageregulator with a 1/8th turn positive locking mechanism, whichsecures into the facemask. The RDV facemask incorporates aspeech diaphragm that provides excellent speech clarity evenunder heavy breathing. The standard HUD is still inside thefacemask with themicrophone. Dockingthe RDV on thefacemask also alignsthe electronicconnection in onesimple step. Afterremoving the RDV fromthe facemask, it shouldbe stored in thedocking station on thewaistbelt strap to keepfree of dirt and debris.1.4 FIRST STAGE PRESSURE REDUCERAir leaves the cylinder, passes through a sintered bronze filterin the handwheel elbow assembly, and then continues onthrough a high pressure flexiblehose to the first-stage pressurereducer where it is reduced to ap-proximately 125 psi. The reduceris a simple piston type that re-quires no adjustment and incorpo-rates an automatic, self-seatingpressure relief valve to protect thelow-pressure components down-stream. It is made of high qualityaluminum, and is securely mount-ed inside the backframe assem-bly.1.5 END-OF-SERVICEINDICATORSThe primary End-of-Service indi-cator is incorporated into the HUD. The display will flash asingle red LED at 23% to 27% of rated cylinder pressure perNIOSH requirements. The primary end-of-service alarmmeets NFPA 1981, 2007 Edition requirements.The secondary End-of-Service indicator is a bellmounted inside the back-frame which is set to acti-vate at 23-27% of ratedcylinder pressure perNIOSH and NFPA re-quirements.1.6 BACKFRAME AND HARNESSThe backframe and harness assembly utilize ergonomic de-sign principles to produce a comfortable, low profile unit thatevenly distributes the SCBA weight between the wearer’ships and shoulders.The unique double-wallbackframe of the Vikingprotects major airlines,the first stage reducer,bell alarm and digitalcomponents. A quick-re-lease cylinder band fits awide range of cylinderswith an infinitely adjust-able latch to ensure atight fitting cylinder.The harness material is NFPA compliant, custom wovenKEVLAR®. The upper harness has very resilient foam rubberpadding for added comfort and PBI/KEVLAR cover for maxi-mum durability and protection. There is an optional back-frame plate that can be ordered (p/n 099038) to reinforce theupper harness straps for departments that do heavy simula-tion training of fire fighter rescue operations. A lower lumbarpad is standard for added comfort and support.1.7 CONTROL CONSOLEThe control console and PASSassembly communicate with eachother through a wireless network.The network uses a discreet fre-quency that eliminates noise andresistance to other radio frequen-cies. This wireless network joinsthe Control Console and PASSassembly together, allowing forconstant data to be exchanged.There are two motion sensors onthe Z SEVEN, one in the ControlConsole and one in the PASS assembly inside the back-frame. When one assembly detects motion, the PASS will re-set for 25 seconds.Note: Only Duracell MN 1500 or Energizer E911.5 volt AA batteries are to be used with the batterypacks. Be sure to place batteries in the direction asindicated on the battery compartment in order to pro-long battery and fuse life.red end of servicealarm
COPYRIGHT 2007 AVON - ISI 51.7.1 SERVICING CYLINDER VALVEAfter each use, and prior to recharging, the cylinder valvemust be inspected for damage. If a new valve is replacing avalve that was damaged in use, it will be necessary to hy-drotest the cylinder before installing the new valve.Note: Any maintenance on the valve that requiresdisassembly should be conducted by an AVON-ISIAuthorized personnel or an AVON-ISI technician whois well trained in the hazards of high pressureequipment. Never attempt to remove the valve fromthe cylinder while there is any pressure in thecylinder. Open the valve completely to be sure it isempty. If the gauge shows pressure but you think thecylinder is empty, contact the AVON-ISI factory foradvice by calling 888-474-7233.Note: Prior to revalving a cylinder, you must perform the fol-lowing inspection:• Remove o-ring from sealing threads on cylinder valve.• Clean threads to remove any lubricant.• Inspect the cylinder threads, ensuring the threads are notdistorted or cracked.• Inspect the valve threads, ensuring the threads are notdistorted or cracked.1.8 CYLINDER AND VALVE ASSEMBLYA range of cylinder types and capacities are available on theVIKING 2216 psi and 4500 psi models. (Please see the tablein Section 1.10 for specifics.)The cylinder valve is of aluminum construction with a perma-nent teflon coating. The valve outlet is a standard CGA-346fitting on 2216 psi cylinders, and a standard CGA-347 fittingon 4500 psi cylinders. Each valve has a dual-reading pres-sure gauge. Valve protection is provided by an elastomericbumper. See section 2.3.2 for inspection prior to use.The valve can be used with AVON- ISI cylinder assembliesbetween 23 cubic feet and 87 cubic feel. The cylinder valvehas a burst disc type safety device to protect the cylinderfrom over pressurization.The cylinders and valve are matched according to pressure.The maximum pressure on the gauge built into the cylindervalve should match the pressure rating on the cylinder. A2216 psi valve will not fit into a 4500 psi cylinder and viceversa. For easy recognition AVON- ISI has made 4500 psihandwheels red and a 2216 psi handwheel black. (Exception:all Viking ST models will have black handwheels no matterwhat the pressure rating of the cylinder.)The cylinder valve has two sets of male threads - one willscrew into the cylinder and the other is used to attach to thepneumatics of the SCBA. The latter threads are referred to asCGA (Compressed Gas Association) threads. It is importantto protect the CGA threads so that the pneumatics will alwaysscrew onto them without doing damage to the handwheel onthe pneumatics.If any threads are distorted or cracked, the parts should betagged “Out of Service” and be condemned.HANDLING PRECAUTIONS:NEVER LIFT OR CARRY UNIT BY THE HIGH PRES-SURE HOSES. IF A HIGH PRESSURE HOSE BE-COMES KINKED OR OTHERWISE DAMAGED, ITSHOULD BE REPLACED. CHECK FOR DAMAGENEXT TO THE METAL ENDS OF THE HOSE.1.9 RAPID INTERVENTION CREW (RIC) FITTINGEvery Viking Z SEVEN has a RIC fitting attached near thehandwheel that allows a downed fire fighter to have their cyl-inder charged from an outside source. NFPA 1981, 2007 Edi-tion requires this fitting on all SCBA’s manufactured for firefighters. The RIC fitting is compatible with other manufactur-ers and is intended as an emergency refill only. The RIC fit-ting will not work as a transfill system between two SCBA’s.There is a dust cap cover for the fitting to prevent debris onthe fitting. See section 4.7 for detailed working instructions.
COPYRIGHT 2007 AVON - ISI61.10 VIKING CYLINDER TABLEaAll Carbon Cylinders have 5 year hydrostatic intervals.024.037.00 2216 Aluminum 1287 liters, 45 cu. ft. 30 min. 20.5 lbs. 6.9 in. 5 years Life024.035.00 2216 Hoop-Wrapped Glass 1301 liters, 45.5 cu. ft. 30 min. 16.0 lbs. 6.9 in. 3 years 15 years124001 2216 Full Wrapped Carbon 1301 liters, 45 cu. ft. 30 min. 10.4 lbs. 6.8 in. 5 yearsa15 years024.098.00 4500 Hoop-Wrapped Glass 1287 liters, 45 cu. ft. 30 min 15.9 lbs. 5.5 in. 3 years 15 years124002 4500 Full Wrapped Carbon 1287 liters, 45 cu. ft. 30 min. 11.0 lbs. 5.4 in. 5 yearsa15 years124003 4500 Full Wrapped Carbon 1887 liters, 66 cu. ft. 45 min. 14.8 lbs. 6.8 in. 5 yearsa15 years124004 4500 Full Wrapped Carbon 2516 liters, 88 cu. ft. 60 min. 19.2 lbs. 7.1 in. 5 yearsa15 years124027 4500 Hoop-Wrapped Glass 1287 liters, 45 cu. ft. 30 min 15.9 lbs. 4.0 in. 3 years 15 years124028 4500 Full Wrapped Carbon 1287 liters, 45 cu. ft. 30 min 11.0 lbs. 5.4 in. 5 yearsa15 years124029 4500 Full Wrapped Carbon 1887 liters, 66 cu. ft. 45 min 14.8 lbs. 56.8 in. 5 yearsa15 years124030 4500 Full Wrapped Carbon 2516 liters, 88 cu. ft. 60 min 19.2 lbs. 7.1 in. 5 yearsa15 years024.066.00 4500 Full Wrapped Glass 1282 liters, 45.3 cu. ft. 30 min 14.1 lbs. 5.6 in. 3 years 15 years024.085.00 4500 Full Wrapped Glass 1854 liters, 65.5 cu. ft. 45 min 18.9 lbs. 6.8 in. 3 years 15 yearsPart Pressure Material Free Air Capacity NIOSH Rated Cylinder & Cylinder Hydrostatic CylinderNumber PSIG Duration @ Valve Charged Diameter Interval Lifeb 2.1 UNPACKINGOpen the storage case or shipping container. Observe therelative position and placement of the various components forfuture repacking. Remove the SCBA from the container andplace on a clean dry surface. Remove the facemask fromprotective bag. Remove battery pack from protective bag. In-stall battery pack into backframe according to battery pack in-stallation instruction in section 8.3. Install control console bat-teries according to installation instructions in section 8.3.2.2 INVENTORY AND EXAMINATIONExamine unit for physical condition and appearance of allcomponents. Be sure the following major components are in-cluded:•Facemask and regulator assembly in storage bag•Backframe and harness assembly•Cylinder and valve assembly•Batteries for control console•Backframe battery pack with batteries if equipped withPASS•Options ordered with unit: buddy breather, airline, etc.2.3 ROUTINE CHECKS AND INSPECTIONSThe following procedure shall be used for new incoming unitsand daily inspections of the apparatus. An SCBA not routine-ly used, but kept for emergency use, shall be inspected atleast monthly. All other breathing apparatus shall additionallybe inspected after each use.NOTE: BLACK KELAR CYLINDER BAGS (PART #: 138082, 138091, 138092, 138093) ARE OPTIONAL COSMETIC COVERS THAT MAY BE PURCHASED TO COVER CYLINDERS.2.0 ROUTINE CHECKSWARNINGTHE APPARATUS MUST NOT BE USED UNTIL THEFOLLOWING TESTS HAVE BEEN SUCCESSFULLYCOMPLETED. ANY DISCREPANCY NOTED DURINGTHE PRE-USE CHECK AND INSPECTION SHALL BECORRECTED ONLY BY AUTHORIZED PERSONNELPRIOR TO USE OF THE APPARATUS.2.3.1 Visually inspect complete apparatus for worn oraged parts and damaged components.2.3.2 Basic cylinder inspection shall include:A. Inspect gauge for damage.B. Inspect cylinder for mechanical damage (cracks,dents, gouges) or signs of heat or chemical damage.(Refer to CGA C-6.2 Guideline for Visual Inspectionand Requalification of Fiber Reinforced HighPressure Cylinders for all wrapped cylinders.)C. Check that hydrostatic test date on cylinder iscurrent.D. Check that cylinder valve threads are notdamaged.E. Check that the valve body is not bent.F. Check that the burst disc outlet is clean and freeof debris.G. If any item listed above is noted, depressurizecylinder to a slight positive pressure, tag, and takeout of service.
COPYRIGHT 2007 AVON - ISI 72.3.3 AirSwitch:Open controlslide onAirSwitch bypressing inwardand upward ontwo protrudingtabs on bothsides of controlslide. Also makesure the redbypass knob isin the closed position (i.e. fully turned clockwisewhen looking at front of mask). See paragraph3.1.9 for connection instructions.RDV: Push inwardon the RDV FirstBreath Button. Also,make sure the redbypass knob is inthe closed position.2.3.4 Ensure high pres-sure handwheel is tightened completely prior toopening the cylinder valve. Open the cylinder valveslowly by turning the cylinder valve knob counter-clockwise to the fully open position. The consoleshould emit an audible chirp. The bell should acti-vate and then shut off. There should be no air flowfrom the facemask. If air is flowing, check that thebypass valve is closed.WARNINGENSURE THAT ONLY A 2216 PSI CYLINDER ISUSED WITH LOW PRESSURE PNEUMATICS AND A4500 PSI CYLINDER IS USED WITH HIGH PRES-SURE PNEUMATICS.2.3.5 CHECK CYLINDER PRESSURE: The heads-updisplay will have four lights "on" when the cylinderis full. When the cylinderpressure is between 3/4and 7/8, the top greenlight will be flashing andthe analog pressuregauge readout shouldread at or above the 7/8thlevel. If the top greenlight is "off" or below thespecified levels, refill thecylinder or replace with afully charged cylinder.2.3.6 AirSwitch: While holding the facemask, pushdown on the top of the control slide to close the Air-Switch and QUICKLY push back to the UP position.First 4 lights ofthe HUD showscylinder pressurebypass latchThere should be a rush of air when the slide ispushed down, and the air flow should stop when theslide is in the UP position.RDV: RDV can be attached from either left or rightorientation. Dock RDV into facemask by turning theRDV until the bypass knob is facing either the 1o'clock or 4 o'clock position depending on user com-fort. Place RDV into mask and rotate till latch is in the12 o'clock position (1/8th turn to lock). Inhale to ac-tive airflow. Attempt to rotate RDV to ensure RDV islocked.2.3.7 Open bypass and check for constant air flow. Closebypass.2.3.8 BATTERY CHECK: If the batteries are low, the topyellow LED on the HUD will be "ON". In addition, ifequipped with PASS, the control console will make abeeping noise every 15 seconds to alert the status ofthe PASS battery and the console LED will be red.See paragraph 8.3 to replace the batteries.2.3.9 LEAK TEST: For the Airswitch, ensure the controlslide is in the up position and the bypass is closed.For the RDV, push inward on the first breath button tostop airflow and make sure bypass is closed. Using afull cylinder, open the cylinder valve slowly until thepneumatics are completely pressurized. Allow pres-sure to stabilize for 30 seconds. Close cylinder valvefor one minute. Open cylinder valve slowly and ob-serve the analog gauge needle movement. If the nee-dle on the gauge moves more than 1/8th inch, the Vi-king should be removed from service and tagged forrepair.
COPYRIGHT 2007 AVON - ISI8TECHNICIAN MAINTENANCEAT LEAST ONCE PER YEAR, THE ENTIRE SCBASHOULD BE PLACED OUT OF SERVICE ANDTAGGED FOR ANNUAL FLOW TESTING BY ANAVON-ISI AUTHORIZED TRAINED TECHNICIAN.2.4 SCBA RETIREMENTOver the course of time, the Viking SCBA needs to be evalu-ated on its' overall condition. Inspect the Viking's harness as-sembly for frayed, deteriorating harness', stress cracks in thebackframe and in general, it's overall condition. Another con-sideration is passing the annual dynamic flow testing require-ments. Over time components may need to be replaced orconsideration must be made to retire the SCBA.Fire Department that plans on retiring their SCBA's or nolonger meet the current NFPA requirements, should reviewNFPA 1852, 2002 Edition, section 4.3 and 4.6 for guidelineson retiring an SCBA.3.1 DONNING PROCEDURES3.1.1 Position the VIKING SCBA on the ground with thecylinder valve facing away from the wearer.3.1.2 Spread the shoulder straps and fold open the sidearms. Ensure all strap assemblies (side and waist)are fully extended and waist belt buckle assembly isnot connected. Reach inside the harness assemblyand grasp the frame with both hands.3.1.3Swing the unit up and over the head, making sure thatthe elbows extend through the loops formed by theshoulder straps. Allow the unit to slide down the back.3.1.4 Pull directly down on the shoulder straps to adjustposition of unit on back, attach chest strap.3.1.5 Connect the waistbelt buckle and adjust waistbelt toa comfortable snug fit by pulling simultaneously on both leftand right adjustment straps. Tuck the excess waistbelt andshoulder strap pull-downs inside the waistbelt.2.3.10 LOW PRESSURE ALARM TEST: Gradually reducethe system pressure by slightly opening the bypassvalve. Verify that the bell sounds and the mask dis-play blinks a single red LED as the needle from theanalog gauge is at the 1/4th increment.2.3.11 Check the RIC fitting to ensure the dust cover is inplace.IMPORTANTCOMPLETE ALL ROUTINE CHECKS AND INSPECTIONPROCEDURES OUTLINED IN SECTION 2 BEFORE START-ING DONNING PROCEDURES, SECTION 3.WARNINGIF ANY OF THE PREVIOUS TESTS FAIL, REMOVEAPPARATUS FROM SERVICE, TAG, AND RETURNFOR REPAIR BY AVON-ISI AUTHORIZEDPERSONNEL.3.0 DONNING PROCEDURES AND SAFETY CHECKS
COPYRIGHT 2007 AVON - ISI 93.1.8 To connect the facemask to the Viking unit, connectelectronics plug partially into socket, then connectfacemask plug into connector. Press firmly in to lockboth fittings into each socket. A click should beheard when it is locked in place securely.Note: When connecting the facemask hose to theconnector, make sure both hoses are connected andthe socket sleeve has moved forward. If socketsleeve has moved forward without the facemaskhose connected, air will leak out of the socketconnector.For the RDV mask, the HUD electronic connectionis made when the RDV is docked into the facemask.Prior to donning the RDV, ensure that the contactpins are free of any debris.Note: In an IDLH atmosphere, such as a CBRN response,ensure that the facemask is connected to thepneumatic connection prior to entering thehazardous area to prevent contamination.Note: Prior to docking the RDV, the user can perform anegative pressure check on the AVON-ISI mask.Place your hand to block off the RDV opening in thefacemask. Inhale slightly and hold your breath.Facemask should move inward slightly and stay inthat position unit user exhales. It may be difficult toperform this with a gloved hand. Annual fit testing isrequired to ensure proper fit.Note: It is not necessary to perform a negative pressurecheck on the AirSwitch because it is designed as apositive pressure facemask. AVON-ISI recommendsannual fit testing to ensure a proper fitting facemask.Pull strapsFORWARDon netharness3.1.6 Don AirSwitch mask: With the control slide in the"up" position and with one hand on the head harnessstraps, put chin into facemask first and then pullharness straps over head. Position facemask so thatchin fits snugly into chin cup and pull the twoharness adjusters forward evenly. Pull net towardbase of the skull to ensure it is seated fully.Don RDV mask: Do not dock the RDV regulator untilafter the mask is donned. With one hand on thehead harness straps, place chin into facemask andthen pull harness strap over users head. Positionfacemask so the chin fits securely in the chin cupand pull the two harness adjusters forward evenly.Pull net toward base of the skull to ensure it isseated fully.IMPORTANTDO NOT OVERTIGHTEN THE FACEMASK. DOING SO MAYCAUSE DISCOMFORT OR FACEMASK DEFORMATIONAND LEAKAGE.3.1.7 Ensure the AirSwitch control slide is in the UP(open) position, and the bypass valve is closed.WARNINGBE SURE TO ALIGN THE CONNECTOR AND FACE-MASK PLUG CORRECTLY AS SHOWN ABOVE.DAMAGE WILL RESULT TO THE PIN IN THE CON-NECTOR IF THE ELECTRONICS PLUG IS MISTAK-ENLY PUSHED INTO IT.facemask plugelectronicsplugconnectorcontactpins
COPYRIGHT 2007 AVON - ISI10AVON-ISI offers facemasks in three different sizes toensure a proper fit. Refer to the AVON-ISI InstructionSheet for the Viking Facemask (p/n 084022, a/wA49022) for proper sizing of the facemask.3.1.9 Ensure high pressure handwheel is tightened com-pletely prior to opening the cylinder valve. Open the cylindervalve slowly by turning the cylinder valve counterclockwise tothe fully OPEN position. The control console should emit anaudible chirp.If equipped with PASS, the PASS should emitan audible chirp. The bell should activate and then shut offand the HUD should be "on", showing quarter increments ofcylinder pressure. The yellow "low battery" LED will light andthen turn off.Note: On the RDV, the HUD will activate AFTER the RDVis docked into the facemask.3.1.10 AirSwitch: To activate cylinder airflow push downon the control slide.RDV: To activate air flow, remove RDV from dockingstation on waistbelt and dock the RDV on the face-mask by orientating the bypass valve in the 1 o'clockor 4 o'clock position, push RDV into the front open-ing, and rotate 1/8th turn. Inhale to activate airflow.WARNINGIF USER IS UNABLE TO ACTIVATE THE “FIRSTBREATH” OPEN BYPASS IMMEDIATELY, REMOVERDV, CLOSE CYLINDER VALVE AND TAG “OUT OFSERVICE”.3.2 SAFETY CHECKSWARNINGTHESE SAFETY CHECKS MUST BE PERFORMEDBEFORE ENTERING A HAZARDOUS AREA. FAIL-URE TO PERFORM THESE CHECKS MAY RESULTIN RESPIRATORY INJURY OR DEATH.3.2.1 AirSwitch positive pressure fit check: With cylin-der valve open, push down on the control slide to activate airsupply and breathe normally.RDV positive pressure fit check: With the maskdonned and the RDV docked, inhale to activate air-flow.Insert two fingers between the facemask and face. Gently liftthe facemask seal away from the face and ensure a goodoutward flow of air, showing that the facemask pressure ispositive. Reseal facemask and stop breathing for 3 seconds.There should be no sound of air leaking from the regulator,and there should be no airflow sensed in the eye region ofthe mask.3.2.2 ALARM CHECK: Close the cylinder valve and con-tinue to breathe normally. As the air reaches the ¼ full levelthe red LED light should flash rapidly and all other lightsshould be out. The secondary bell alarm should also activate.3.2.3 Open cylinder valve. Take two to three deep breathsto ensure you are getting adequate air into the facemask. Thefacemask should not move towards your face.3.2.4 AIRSWITCH BYPASS CHECK: The red bypassknob is located in the center of the AirSwitch. Turn the by-pass knob clockwise as viewed inside the mask (the directionshown by the knob arrow) to open the bypass valve. A con-stant flow of air should pass into the facemask. Turn the knobin the opposite direction to turn the bypass valve off.RDV BYPASS CHECK: The bypass knob on theRDV is located on the right side (from the wearerview). To open, rotate knob towards the user fully. Aconstant flow of air should pass into the facemask.Turn the knob in the opposite direction to close.3.2.5 RECHECK CYLINDER PRESSURE: Check theheads-up display. Four lights should be "on". Thetop green light may be flashing, indicating at least 7/8th full.Verify the analog gauge is at or above the 7/8th level.bypass
COPYRIGHT 2007 AVON - ISI 11IMPORTANTTHE USER SHOULD BE TRAINED ON HOW TO HANDLE APOSSIBLE EMERGENCY BEFORE ENTERING A HAZARD-OUS AREA.The Viking SCBA can be equipped with a variety of fully-inte-grated solid state features that offer safety and communica-tion advantages for the user. Review section 9 for detailed in-structions of available options.4.1 READING THE HEADS-UP DISPLAY (HUD)4.1.1 The HUD includes five LED lights: two green, twoyellow and one red. Each of the 4 LEDs in a row represents aquarter increment of the rated service pressure. As cylinderpressure decreases, the LEDs change status. At full ratedservice pressure, all four LEDs are on. As cylinder pressuredrops below full, the top green LED begins blinking. At ¾rated service pressure, the top green LED turns off and thenext green LED begins blinking. At ½ rated service pressure,the second green LED turns off and the yellow LED beginsblinking. At ¼ rated service pressure, the yellow LED turnsoff, and the red LED blinks at a fast rate. The top offsetyellow light is a low battery indicator. Refer to the followingtable for more information regarding mask pressure displayinterpretation.3.2.6 BATTERY CHECK: The top yellow LED will be "ON"when the control console batteries are low. If thepass batteries are low, displays red LED on consoleand the pass alarm will chirp every 15 seconds. TheLED on the console will be red. If the SCBA shows alow battery warning, replace batteries in accordancewith section 8.3.3.2.7 VAS CHECK3.2.7.1 Turn SCBA on by either opening cylinder valve or bymanually depressing on buttons.3.2.7.2 Hold mask up to face and speak into mask.3.2.7.3 Listen to speech emanating from VAS speaker andensure its intelligibility and function.WARNINGSIF ANY OF THE ABOVE CHECKS FAIL, DO NOTPROCEED. REMOVE THE APPARATUS FROM SER-VICE, TAG, AND RETURN FOR REPAIR BY AVON-ISI AUTHORIZED PERSONNEL.USE OF THE BYPASS IN NON-EMERGENCY SITUA-TIONS WILL SUBSTANTIALLY REDUCE DURATIONOF THE APPARATUS.THE BYPASS WILL NOT FUNCTION IF THE CYLIN-DER IS OUT OF AIR.4.0 DURING USERemainingCylinderPressureFullFull → 3/43/4 → 1/21/2 → 1/4Below 1/4 Low battery:consoleRED••••YEL-LOW•••GREEN•••GREEN YEL-LOW• = On = Blinking = Off•4.2 NORMAL USE4.2.1 Monitor cylinder pressure for remaining air supplyusing the HUD. Cylinder pressure can also be moni-tored with the analog pressure gauge. Refer to chartin paragraph 4.1.1 for the LED light sequence.4.2.2 The end-of-service-time alarms (mask display andbell) activate when there is approximately 25% of thefull air supply remaining. Egress when alarms acti-vate. WARNING: 25% OF A FULL CYLINDER MAYBE INSUFFICIENT IN SOME CIRCUMSTANCES TOSAFELY EXIT FROM AN IDLH ATMOSPHERE. Oneexample would be a long-distance ingress through acontinuous IDLH atmosphere. In such situations, be-gin egress prior to activation of the end-of-service-time indicator.4.3 CBRN SPECIFIC ACTIONSHazardous materials, such as CBRN agents, maynot present immediate effects from exposure, butcan result in delayed impairment, illness, or death.Use the AVON-ISI Viking with CBRN agent approvalin conjunction with personal protective ensemblesthat provide appropriate levels of protection againstdermal hazards. Refer to page 2 of this manual,yellowyellow (B)(low battery)greenred
COPYRIGHT 2007 AVON - ISI12Cautions and Limitations for CBRN Protection Ap-proval.4.4 INSTRUCTIONS FOR CHANGING CYLINDERS4.4.1 Make sure cylinder valve is closed and all air is re-leased from the pneumatic system.4.4.2 Pull outward on the upper portion of the lockinglatch to release tension.4.4.3 Disconnect handwheel from cylinder valve and re-move cylinder by sliding cylinder upward throughcylinder band.4.4.4 Insert new full cylinder by sliding down through cyl-inder band until cylinder rests against bottom retain-er. Connect handwheel to cylinder valve and posi-tion cylinder.4.4.5 Close the locking latch.4.5 CYLINDER BAND ADJUSTMENT4.5.1 Pull outward on the upper portion of the lockinglatch to release tension.4.5.2 To loosen the cylinder band, grab the inner cylinder-band strap and pull out/away from the adjustmentlatch.To tighten the cylinder band, grab the outer cylinderband trap and pull up/away from the adjustmentlatch. Slide the slack across the inner strap.4.5.3 Further adjust cylinder band length until tight. Makesure that the locking latch is in the open position. Slide the slack across the lower strap.4.5.4 Close the locking latch.Note: Over tightening latch can break the latch. Cylinderband should hold cylinder firmly.4.6 EMERGENCY EGRESS INDICATORSIf any of the following situations occur, egress immediately:A. Exposure to flashoverB. Exposure to high temperatureC. Harness failureD. Chattering or unusual noises from SCBAE. Submersion in water (Note: In this situation the VI-KING will continue to supply air on demand to adepth of at least 3 meters.)F. SCBA subjected to high impact such as a fallG. Air flow decreases such that the facemask moves in-ward toward the face during inhalation (Note: In thissituation, open bypass to provide extra, constantflow.)H. Air flows constantly at a high rate (Note: In this situa-tion, adjust the flow rate by slowly closing the cylin-der valve until a comfortable flow rate is established.The flow rate should match the bypass flow rate dur-ing normal operation.)
COPYRIGHT 2007 AVON - ISI 13II. Digital pressure gauge, mask pressure display, orother digital options cease to function properly.J. End-of-service indicators activate.K. Chemical agent egress indicators:1. Dizziness2. Partial loss of vision3. Shortness of breath4. Restricted breathing5. Localized pain6. Redness of skin4.7 RIC FITTING PROCEDURESThe RIC fitting is designed as an emergency refill only andhas specific uses and functions per NFPA 1981, 2007Edition. The system can only be used to fill approved SCBAcylinders. The RIC fitting has an internal balanced pistonthat prevents over pressurization of a cylinder. A check valveprevents fire fighters from transfilling SCBA’s, or any otherunapproved use on AVON-ISI products. Users will be able tohave a 4500 psi cylinder as a supplied air system andconnect to a 2216 psi SCBA RIC connector. Air will stopflowing automatically from the high-pressure cylinder whenthe correct pressure (2216 or 4500) is achieved.To recharge a cylinder on a downed fire fighter, an approvedcharging hose must be used. The AVON-ISI Rescuer usesthe following approved hoses: a 3 foot RIC Charging Hose(p/n 162051), a 6 foot RIC Charging Hose (p/n 162052), or a10 foot RIC Charging Hose (p/n 162053) for filling thecylinder in IDLH atmospheres.4.7.1 Open cylinder valve of supplied air and remove thedust cap from the RIC charging hose. Inspect thefire fighters cylinder for damage and ensure that thecylinder valve is fully opened.WARNINGCYLINDERS THAT ARE DAMAGED MAY SUDDEN-CYLINDERS THAT ARE DAMAGED MAY SUDDEN-CYLINDERS THAT ARE DAMAGED MAY SUDDEN-CYLINDERS THAT ARE DAMAGED MAY SUDDEN-CYLINDERS THAT ARE DAMAGED MAY SUDDEN-LY RUPTURE IF CHARGED.LY RUPTURE IF CHARGED.LY RUPTURE IF CHARGED.LY RUPTURE IF CHARGED.LY RUPTURE IF CHARGED.4.7.2 Remove dust cap from the RIC fitting on the SCBAand attach the RIC charging hose to it. Listen forleaks on the SCBA that is being filled. Rechargingwill take between 2-4 minutes, depending on thecylinder duration and pressure. When the pres-sures equalize, unplug the charging hose from theSCBA and replace dust covers and exit. During a pro-longed rescue, users can leave the supplied air cylin-der plugged into the downed fire fighter’s SCBA, add-ing additional duration to the cylinder.Note: If any time during charging, a leak is detected; dis-continue charging and exit IDLH atmosphere immedi-ately.Note: In a non-emergency situation, cylinders shall not berefilled through the RIC. 4.7.3 Once clear of an IDLH atmosphere, close the cylindervalve on the RIC charging hose. Ensure there is nodebris in the dust cap prior to pushing on the dustcap. The bottom of the dust cap reads "press to re-lieve". With dust cap in place, push down on dust capon a hard surface to bleed pressure.4.7.4 Top off cylinder attached to charging hose beforenext use to ensure proper service time.IMPORTANTDO NOT REMOVE ANY EQUIPMENT UNTIL YOU ARECLEAR OF AN IDLH ATMOSPHERE.bottom of RICcharging hose
COPYRIGHT 2007 AVON - ISI145.1 DOFFING5.1.1 AirSwitch: Push the control slide UP on the Air-Switch.5.1.2 RDV: Push first breath button inward to stop airflow.Push locking latch outward and rotate 1/8th turn toremove RDV.RDV: Dock on RDV docking station on waistbelt.5.1.3 Loosen head harness straps fully and remove face-mask.5.1.4 Close the cylinder valve by turning it fully clockwise.5.1.5 Release air pressure in the system by opening thebypass until the air flow stops, then closing it.5.1.6 Turn off all the electronics on the Z SEVEN model bysimultaneously depressing the buttons on both sideof the control console.5.1.7 Place facemask on the shoulder harness clip.5.1.8 Unfasten the waistbelt and loosen shoulder straps.Extend shoulder straps and waistbelt fully. Unhookchest strap.5.1.9 Remove the apparatus.WARNINGDURING COLD WEATHER OPERATIONS, THE AIR-SWITCH REGULATOR SHOULD BE STORED IN THECLOSED POSITION (CONTROL SLIDE DOWN) TOPREVENT ICE BUILDUP INSIDE THE REGULATOR.THIS PRACTICE IS NECESSARY AS ICE MAY IN-TERFERE WITH THE SEALS OF THE AIRSWITCHREGULATOR WHILE IN USE.5.1.10 Remove the cylinder and tag it for refilling. See Sec-tion 8.2 for instructions.5.1.11 Do not store or place apparatus in ready position un-til after performing “After Use Cleaning” Section 6.WARNINGSCBA USED IN A HAZMAT OR CBRN ENVIRON-MENTS MUST GO THROUGH DECONTAMINATIONPROCEDURES. IF THE SCBA IS CONTAMINATEDWITH CBRN AGENTS, DISPOSE OF THE SCBA AF-TER DECONTAMINATION, IN ACCORDANCE WITHLOCAL GOVERNMENT INSTRUCTIONS OR PROCE-DURES.USE IN CONJUNCTION WITH PERSONAL PROTEC-TIVE ENSEMBLES THAT PROVIDE APPROPRIATELEVELS OF PROTECTION AGAINST DERMAL HAZ-ARDS.SOME CBRN AGENTS MAY NOT PRESENT IMMEDI-ATE EFFECTS FROM EXPOSURE, BUT CAN RE-SULT IN DELAYED IMPAIRMENT, ILLNESS, ORDEATH. DIRECT CONTACT WITH CBRN AGENTSREQUIRES PROPER HANDLING OF THE SCBA AF-TER EACH USE AND BETWEEN MULTIPLE EN-TRIES DURING THE SAME USE. DECONTAMINA-TION AND DISPOSAL PROCEDURES MUST BE FOL-LOWED. IF CONTAMINATED WITH LIQUID CHEMI-CAL WARFARE AGENTS, DISPOSE OF THE SCBAAFTER DECONTAMINATION IN ACCORDANCEWITH LOCAL GOVERNMENT INSTRUCTIONS ORPROCEDURES.THE RESPIRATOR SHOULD NOT BE USED BE-YOND 6 HOURS AFTER INITIAL EXPOSURE TO5.0 AFTER USE PROCEDURES
COPYRIGHT 2007 AVON - ISI 15CHEMICAL WARFARE AGENTS TO AVOID POSSI-BILITY OF AGENT PERMEATION.IMPORTANTDirect contact with CBRN agents requires proper handling ofthe SCBA after each use and between multiple entries duringthe same use. Decontamination and disposal proceduresmust be followed. If contaminated with liquid chemical war-fare agents, dispose of the SCBA after decontamination. Forcomplete instructions on decontamination procedures for achemical environment, please reference National InstituteStandard Technology (NIST) Special Publication 981 atwww.counterterrorism.org/pdf/nistspecialpub981.pdf.WARNINGTO AVOID DAMAGE TO THE VISOR, DO NOTPLACE THE FACEMASK DOWN ON ROUGH SUR-FACES.6.1 CLEANING AIRSWITCH REGULATOR ANDFACEMASK6.1.1 Disconnect facemask hose by pushing connectorinto socket and pulling back on the socket sleeve.The electronics will unplug with the facemask hose.Open the AirSwitch.6.1.2 Wash the facemask in cool to warm soapy water.Use a mild, non-detergent, dish washing soap (e.g.Ivory). The heads-up display is completely submers-ible.Note: Do not immerse the hose end and electrical connec-tor in water.6.1.3 After rinsing, shake to remove excess water, pluginto low pressure line and close AirSwitch to allowfree-flow for a few seconds. Repeat process severaltimes.NOTE: Where further cleaning due to heavy contaminationis required, clean with AVON-ISI recommended dis-infectant/cleaner (p/n 013004) after rinsing the face-mask. Use of other disinfectants may cause damageto SCBA components.6.1.4 When dry, polish the visor inside and out with a softclean, lint-free cloth.6.1.5 Ensure all head harness straps are fully extended,6.0 AFTER USE CLEANINGready for use.electricalconnector
COPYRIGHT 2007 AVON - ISI16NOTE: Cylinders that are tagged for repair should always bestored empty with the cylinder valve closed to preventcontamination or condensation inside the cylinder.8.2.2 Prior to filling cylinder, follow the basic inspectionprocedures outlined in paragraph 8.1.18.2.3 Cylinder air shall meet or exceed the standards inNFPA 1500, paragraph 7.9.1.8.2.4 Fill cylinder to maximum rated pressure (FULL).Wait at least 30 minutes to allow cylinder to cool,then add extra air to return to full at room tempera-ture. (Note: pressure drops when cylinder tempera-ture drops.)8.3 BATTERY PACKSBATTERIES FOR CONTROL CONSOLE: Thecontrol console battery pack powers the HUD, VASand radio interface. The battery pack accommodatessix alkaline batteries. The low battery indicator is thein-mask HUD offset top yellow light, displaying a solidyellow light. The LED light on the console will be red.BATTERIES FOR PASS: The PASS battery packwithin the backframe powers only the PASS option. Itaccommodates two sets of four AA alkaline batteries.Each set of four is independent of the other in case of abattery failure. As battery voltage drops, each set of fourbatteries switch to the highest voltage side available untilthe HUD low battery indicator shows that all eightbatteries need replacing. The low battery indicator is thein-mask HUD offset top yellow light, displaying a solidyellow light. The control console will also emit an audibleNOTE: The Viking SCBA facemask and elastomers should beinspected periodically for cracks, abrasions, cuts and signsof heat or chemical damage. If detected, the unit should betaken out of service until repaired.8.1 MAINTENANCE INTERVALS8.1.1 Perform annual dynamic flow test using Posichek IIIwith AVON-ISI software as outlined in NFPA 1852.8.1.2 Every three years disassemble, clean and inspect o-rings on major components.8.2 CYLINDER FILLING PROCEDURES8.2.1 Basic cylinder inspection shall include:A. Inspect gauge for damage.B. Inspect cylinder for mechanical damage (cracks,dents, gouges) or signs of heat or chemicaldamage. (Refer to CGA C-6.2 "Guideline forVisual Inspection and Requalification of FiberReinforced High Pressure Cylinders" for allwrapped cylinders.)C. Check that hydrostatic test date on cylinder iscurrent.D. Check that cylinder valve threads are notdamaged.E. Check that the valve body is not bent.F. Check that the burst disc outlet is clean and freeof debris.G. If any item listed above is noted, depressurizecylinder to a slight positive pressure, tag, andtake out of service.7.1 SCBA STORAGE7.1.1 Complete routine checks and inspection proceduresoutlined in Section 2.3 of this manual.7.1.2 Ensure complete apparatus is clean and dry.7.1.3 Ensure AirSwitch is in the UP position, and the by-pass knob is in the CLOSED position.7.1.4 Ensure RDV is stored in RDV docking station.7.1.5 Ensure facemask and head harness straps are fullyextended. Unplug facemask assembly and store incase, positioned to avoid distortion.7.1.6 Ensure shoulder and waistbelt straps are fully ex-tended.7.1.7 Place the complete apparatus in the storage case orsuitable storage place so it can be easily reached foremergency use.7.1.8 Mounting SCBA in vehicle: When storing the SCBAusing mounting brackets, ensure that brackets are se-cure and that no sharp objects will come in contact withthe SCBA. Ensure that the brackets do not interferewith the backframe components.7.1.9 Ensure control console is turned off and is clean anddry.7.0 SCBA STORAGE8.0 USER MAINTENANCE
COPYRIGHT 2007 AVON - ISI 17chirp every 12 seconds and the console LED passlight will be red.Note: Electronics will operate at least two hours in lowbattery mode.Battery life depends on many variables. Some firedepartments may use the Viking once every day forsix months before they have to change batteries.Another fire department may only use the Vikingonce a month. Both batteries may have to be re-placed within six months. The difference is theamount of power loss from using the electronic op-tions. The Viking Z SEVEN has several options thatcan increase battery consumption. The VAS drawsabout 700 ma. and radio communications drawsabout 250 ma. The rest of the lights that use LED’sdraw very little power. Heat and cold also affect bat-tery life. During internal heat tests (160 ºF) and coldtests (-25º F) battery life dropped by 50%.WARNINGWHEN REPLACING THE AA BATTERIES, ENSURETHAT THE BATTERIES ARE NOT INSTALLEDBACKWARDS WITHIN THE BATTERY PACK. RE-VERSING THE POLARITY OF THE BATTERY FOREVEN ONE SECOND CAN CAUSE THE BATTERYTO LEAK OVER TIME. IF A BATTERY IS IN-STALLED BACKWARDS, DO NOT USE THIS BAT-TERY BUT DISPOSE OF THIS BATTERY. FAILURETO REPLACE THIS BATTERY WILL CAUSE COR-ROSION OVER TIME AND CAUSE A COMPLETEBATTERY FAILURE.Note: Only Duracell MN 1500 or Energizer E91 AA batteries areapproved for use through intrinsic safety standards for useon the Viking SCBA.8.3.1 CONTROL CONSOLE BATTERY PACK REMOVAL:Remove the two screws on the back cover of theconsole. Seperate the cover from the console base.It may be necessary to carefully pry the cover off.The batteries are in pairs of two.8.3.2 CONTROL CONSOLE BATTERY REPLACEMENT:Remove old batteries, observice the polarity. Installnew batteries using new alkaline MN 1500 or E 91AA batteries. Ensure that each battery touches eachcontact point. Tighten screws to secure back con-sole cover. Do NOT over-tighten.8.3.3 PASS BATTERY PACK INSTALLATION: Ensurebattery pack seal is in place, free from debris, andthat the “T” guard between the battery clips is inplace, protecting against shorting out the batteryfuse. Push battery pack into battery compartmentsuch that the clips snap over the two brass contactpins. The control console will turn on, emit an audi-ble chirp, and then turn off. Secure battery pack tobackframe with four Torx screws.8.3.4 PASS BATTERY PACK REMOVAL: Completelyloosen four Torx screws which secure the batterypack to the backframe. Begin lifting battery pack outof the battery compartment by prying with a coin orflat-head screwdriver under the battery pack recess.8.3.5 PASS BATTERY REPLACEMENT: With the batterypack removed from the backframe, remove old batteries frombattery pack and replace with new AA alkaline batteries. En-sure that each battery is properly installed, noting polarity asshown in battery compartment and battery compartment tray.Ensure that each battery touches both battery pack contacts.Ensure battery pack seal is in place, free from debris. Prior toplacing the battery pack within the backframe, ensure that the“T” guard between the battery posts is in place, protectingagainst shorting out the battery fuse. Push battery pack intobattery compartment such that the clips snap over the twobrass contact pins. The control console will turn on, emit anaudible chirp, and then turn off. Secure battery pack to back-frame with four Torx screws.8.4 NET HEAD HARNESS REPLACEMENTTools Required: Harness tool8.4.1 Pull up on top retaining clip that holds head harnessin place. Slide harness through the clip and pullthrough bracket. Repeat on other side. Remove low-er strap from adjuster.8.4.2 Position new head harness to match up with face-mask.8.4.3 Slide head harness through the two top visor brack-ets using harness tool or jeweller screwdriver to pullharness through opening.8.4.4 Slide retaining clip through head harness and lock inplace.8.4.5 Attach lower straps through adjuster rollers.8.5 BACKFRAME HARNESS REMOVAL FORCLEANING AND DECONTAMINATION8.5.1 Upper Shoulder Strap Removal/Installation8.5.1.1 Separate lower shoulder straps from upper shoulderstraps by passing straps through buckles.8.5.1.2 Pull z-fold through plastic tabs on left shoulderstrap.
COPYRIGHT 2007 AVON - ISI18.5.1.3 Pull comm cable through Kevlar loops..5.1.4 Slide backframe cap up to provide access to uppershoulder strap brackets..5.1.5 Push upper shoulder straps into backframe approxi-mately one inch. Turn brackets upright and pull outof backframe..5.1.6 Pass upper shoulder straps through backframe capslots to remove backframe cap..5.1.7 For installation, reverse the above steps..5.2 Side Arm Removal/InstallationTools required: two T-25 torx, Loctite 222.5.2.1 Remove any accessory that is attached to waist beltstrap..5.2.2 Remove side arms by using two torx drivers to un-screw the bottom screw.9ToestoN9 98.5.2.3 To install, reverse the above steps and use Loctite222 on the lower sidearm screws before tightening.8.5.3 Lower Shoulder and Waistbelt Strap Removal andInstallation8.5.3.1 Separate lower shoulder straps from upper shoulderstraps by passing straps through buckles.8.5.3.2 Remove waistbelt straps by passing waistbelt strapsthrough lower shoulder strap buckles.8.5.3.3 The male belt buckle is attached to the left side ofthe backframe. The female belt buckle is attached tothe right side of the backframe (from the user's per-spective).8.5.3.4 Pass right lower shoulder strap through right sidearm. Starting on the outside, pass strap through sidearm until buckle is positioned 3" from side arm. Passback to the outside, then inside, then outside, andthen inside. Pass right lower shoulder strap throughright upper shoulder strap buckle. Do not pass strapthrough two slots at bottom of side arm. Repeat in-structions for left lower shoulder strap.# Description1 PASS Panic button2 Shift key: select voice level activation3 Function key: select On/Off for VAS4 Right LED: green = console power onred = low battery indicator5 Left LED: green = PASS onflashing red = PASS pre or full alarm6 PTT - push to talk button for radio com7 Center speaker for VAS and radio com8 PASS reset buttons power on/off buttons9 Radio interface connection10 Facemask interface power cable11 Pressure transducer connectionChart for Control Console Keys and Description.1 CONTROL CONSOLE KEYS & FUNCTIONS.1.1 The control console is mounted on the upper leftshoulder strap. As with the HUD, the console turnson automatically when the cylinder valve is opened.The control console has several function buttons.Please review the following diagram for locationsand the chart for function. All locations are fromthe user's perspective.9.0 VIKING Z SEVEN OPTIONSNote: At 3.8V, low battery indicators will display<120 psi = HUD will not display any lightsAuto off delay - after cylinder is closed, consolewill turn off automatically after 2 minutes on non-pass units.72356481118(not pictured)910
COPYRIGHT 2007 AVON - ISI 19Level HUD LED Pattern1 Flashing Red2 Red, Flashing Yellow3 Red, Yellow, Flashing Green4 Red, Yellow, Green, Flashing Green5 Red, Yellow, Green, Green6 Flashing Red, Low bat7 Red, Flashing Yellow, Low Bat8 Red, Yellow, Flashing Green, Low Bat9 Red, Yellow, Green, Flashing Green, Low Bat10 Red, Yellow, Green, Green, Low Bat1 2 3 4 5 6 7 8 9 109.1.2.3 RADIO INTERFACEWhen the Z SEVEN is equipped with radio interface,it has the ability to significantly decrease the back-ground noise of outgoing transmissions. This is dueto the placement of the sealed microphone insidethe nosecup, which is well insulated from ambientnoise. Incoming transmissions are broadcast fromthe console speaker. On units designed for use bylaw enforcement, incoming transmissions are re-cieved through an optional ear speaker.A separate radio lead is required to integrate theconsole to the radio. The radio connects to the inter-face cable on the lower control console.There are two ways to key the radio and transmit: inthe manual mode, press and hold the Push-To-Talkbutton (PTT) on the side of the console. As an indi-cation that the PTT button has been pressed, theright LED indicator light turns green on in the con-sole display and a solid green light on the HUD. IfVAS is installed with Radio Interface, the VAS is dis-abled whenever the radio is keyed.To activate the hands free VOX mode, press and re-lease the PTT button twice within one second (dou-ble click). A flashing red light will illuminate on thecontrol console display. In this mode, the radio iskeyed automatically whenever the SCBA sensesuser speech. The HUD will illuminate only the topgreen (full) light whenever user speech has keyedthe radio. When speech has ended, the unit auto-matically turns off the amplifier to conserve the bat-tery and the HUD again monitors cylinder pressure.To end the hands free mode, double click the PTTbutton again..1.2 COMMUNICATIONSThe Viking Z SEVEN is available with several communicationptions. The microphone is a standard feature and is mount-d inside the facemask on the nosecup. It offers excellentpeech clarity. All communications have a noise suppressoro reduce exhaled breathing air noise.Note: The Viking Z SEVEN electronics and pneumaticsturn on automatically when the cylinder valve isopened. The SCBA electronics can be turned onmanually by depressing the lower two ON/OFF but-tons on the console..1.2.1 VOICE AMPLIFICATION SYSTEM (VAS)The VAS uses a sealed, in-mask microphone to cap-ture the user's voice, amplifies it, and then broad-casts it from the speaker on the console. This is par-ticularly useful in communicating with other peoplenearby when the SCBA is in the positive pressuremode. VAS is preset to be voice activated. You mustspeak slightly louder than normal to activate VAS.The VAS is on standby mode whenever the SCBAcylinder is opened. When speech is sensed, it turnson the amplifier and sends it to the console. Shortlyafter speech ends, the amplifier goes back intostandby mode.VAS can be turned off if the user desires. To turn offthe VAS, the cylinder valve must be opened andpower activated to the control console. To disablethe VAS, push inward on the Function key and pushthe PTT button. An audible chirp should be heard.VAS is now in the off setting. To turn VAS back on,repeat the above function. When the Viking SCBA ispowered down, the system will defaut to VAS "on"when the electronics are activiated.9.1.2.2 VOICE ACTIVATION LEVELSThe microphone activation level is adjustable for in-dividual preference. Push the Shift button on thefront of the console inward and hold. The HUD face-mask display will flash the preset point of the voiceactivation level. To change the settings, while hold-ing the Shift key, push the PTT button once. This willraise the activation point. Continue to push the PTTto your personal preference. Release the Shift key toset activation level. To go from Level 4 to Level 1,hold the Shift key inward and push the PTT buttonagain.There are four set points for the voice activation lev-el. Level 1 is the most sensitive activation point up toa Level 4 being the least sensitive activation point.Each level will be displayed a specific number ofHUD light(s) that activate. With each increased level,less inhalation breathing noise is heard, but voicemust be raised higher to begin amplification in orderfor the microphone to detect speach. The settingsare a follows:Amount breathing noiseamplified
COPYRIGHT 2007 AVON - ISI209.1.3 VIKING Z SEVEN PASSThe PASS on the Viking Z Seven is an NFPA 1982compliant Personal Alert Safety System (PASS) thatis integrated with the SCBA and with the other elec-tronic systems. It requires no adjustments.The PASS is automatically activated when thecylinder is opened or may be manually turned on bypushing both "ON/OFF" side buttons on the consolesimultaneously. Once turned on, it normally operatesin the “sensing” mode where it looks for motion at theconsole.9.1.3.1 PASS Operating Instructions WARNINGALWAYS TEST THE PASS PRIOR TO ENTRY INTOA HAZARDOUS ATMOSPHERE. IF THE LOW BAT-TERY WARNING SIGNAL ACTIVATES, INSTALLNEW BATTERIES AFTER USE OR PRIOR TO USINGTHE VIKING Z SEVEN. THE CONTROL CONSOLEWITH PASS SHOULD BE POSITIONED FLATAGAINST THE SHOULDER STRAP.When the PASS is turned on, a chirp will be heard onthe control console speaker, followed by a chirp from thePASS alarm on the backpack. Additionally, the left LED usersprospective on the console display will slowly flash greenwhen PASS is on. When there is a lack of motion sensed atthe control console or PASS device in backframe for over 25seconds, the PASS will go into pre-alarm and sound an audi-ble warning that will progressively get louder until the PASSgoes into full alarm. While in pre-alarm, the red (¼ full) andtop green (full) lights on the HUD will flash and the PASS LEDlight on the console will change to rapidly flashing red. In pre-alarm, motion to the control console or pushing the side but-tons on the console will return the PASS to the sensing mode.If no motion is sensed for a full 35 seconds (including the pre-alarm warning), the PASS will go into full alarm and can onlybe reset by pushing in on the two side ON/OFF buttons on theconsole.9.1.3.2 PASS Safety Certification and Approval• The Viking Z SEVEN with PASS is Certified Intrinsi-cally Safe for use in Class 1, Division 1, Group A, B, Cand D Hazardous Locations.• NFPA Specification: Meets the current NFPA 1981,2007 edition specifications and NPFA 1982, 2007edition.• NIOSH Specification: Meets the standards of 42CFR,Part 849.1.3.3 PASS SpecificationsAlarm level: greater than 95 dbA @ 3 m (approximately10 ft)Visual / Audio Indicators:Turn ON Chirp from Console speaker, then chirp fromPASS alarm, and flashing green PASS light.Turn OFF Low beep from console speakerPre-alarm (No motion sensed for 25 seconds):PASS light turns from green to red and flashrate increasesEnd lights on mask display flash alternatelyPre-alarm warning with increasing soundlevelAlarm (No motion sensed for 35 seconds):PASS alarm soundsPASS LED light on console flashes redMask display shows cylinder pressureMaintenance After each use, clean the control console with adamp cloth and warm water. Do not use cleaningsolvents. Inspect each unit for signs of physicaldamage.Life Depending on the frequency of use, the PASSmay have to be retired from service if severelydamaged.9.1.3.4 PASS LimitationsThe VIKING Z SEVEN is designed to meet the de-sign and performance requirements for PersonalAlert Safety Systems (PASS) to be used by firefight-ers engaged in rescue, fire fighting, and other haz-ardous duties defined in the NFPA 1982 Standardon PASS, 2007 edition. Failure to ensure that the Vi-king Z SEVEN PASS is fully operational prior to usemay expose the user to serious injury or death. Al-though the Viking Z SEVEN PASS meets the currentstandards, there is no guarantee against PASS fail-ure. Most performance properties of the PASS can-not be tested by users in the field.9.1.3.5 PASS WarrantyAVON-ISI warrants the Viking Z SEVEN PASS to befree from defects in workmanship and materials for aperiod of one year from date of purchase. AVON-ISIwill not repair or replace any merchandise that hasbeen damaged from accident, misuse, or abusewhile in the possession of the end-user. AVON-ISIshall not be liable for any direct, incidental or otherconsequential loss or damage arising out of the fail-ure of the device to operate. PASS issues may bereported to AVON-ISI Customer Service at (888)474-7233. After working with the manufacturer to re-solve any issues, they may be reported to SEI at(703) 525-2354.9.2 VIKING STEALTH MODEThe Viking Z-ST model designed for law enforcement has thecapability of turning off the control console. The Stealth Modeis a standard feature of the Viking Z-ST.On units with the stealth mode option, depress the funtionkey and the PPT button on the control console for one sec-ond to turn off VAS. The HUD will still display cylinder pres-sure and acknowledge radio transmissions. All communica-tions will be received through the optional ear piece interfacecable. To reset to normal mode, depress the function key andPTT button on the control console for one second.
COPYRIGHT 2007 AVON - ISI 21Viking SCBA.9.3.2.1 The EAS tether is designed so you do not have tounplug the regulator hose from the facemask in anIDLH atmosphere. The EAS tether includes two feetof retractable hose stored within the backframe. Theend of the hose includes two couplings, one maleand one female, and a combination handle/dust cap.When stored, the EAS handle is located on the lowerright side of the backframe (from the user’s perspec-tive). In an emergency, the EAS tether is pulled outof the backframe and connected to another EAS teth-er forming a four foot long combined tether hose.9.3.2.2 If the EAS is used, egress immediately to a safe, re-spirable atmosphere. The rescuer must monitor theircylinder air closely due to increased air consumption.9.3.2.3 Although the EAS is a NIOSH accepted SCBA ac-cessory, NIOSH does not approve the use of EASdevices. Use of the EAS voids NIOSH approvalswhile in use.9.3.2.4 REMOVE THE EAS TETHER: Using your righthand, reach back above the cylinder valve knob andlocate the buddy breather handle. Pull down on thehandle and completely pull out the hose. The tetheris approximately two feet long.9.3.2.5 CONNECT TO ANOTHER EAS TETHER: EachEAS tether includes both male and female quickconnect couplings. Connect one coupling, eithermale or female, to the opposite coupling on the otherEAS tether. Air will start to flow immediately.9.3.2.6 Egress to a safe, respirable atmosphere and thendisconnect EAS tethers.9.3.2.7 To store EAS tether, while the SCBA pneumatics arepressurized, push the hose length back into thebackframe. Snap the handle into the backframe andreplace dust caps.IMPORTANT9.3 ADDITIONAL OPTIONS9.3.1 AIRLINE DESCRIPTION, LIMITATIONS &OPERATIONNote: Airline options are available on all models of the Vi-king SCBA.9.3.1.1 The Airline Attachment is located on the left waist-belt strap. It is approved with Hansen HK. HansenHK couplings include locking devices.IMPORTANTOnly Hansen HK airline fittings are offered on CBRN certifiedunits.The use of airline attachments on CBRN approved units arenot NIOSH CBRN approved for use in confirmed or potentialCBRN environments.9.3.1.2 When using supplied air, the user must ensure thatthe cylinder valve is closed. Failure to do so may re-sult in reduced cylinder duration.9.3.1.3 Airline respirators can be used only when the respi-rators are supplied with respirable air meeting the re-quirements of CGA G-7.1 Grade D or higher quality.9.3.1.4 When used as a combination apparatus, only 20% ofthe service pressure may be used on entry.9.3.1.5 This approval applies only when the device is sup-plied with respirable breathing air through 6 to 300feet of hose at air pressures between 80 to 120pounds per square inch gauge or from self containedair supply.9.3.1.6 Follow Donning Procedures located in Section 3.0and Safety Checks in Section 3.2.9.3.1.7 Plug airline hose from Viking into supplied airlinehose. Supplied air pressure shall be between 80 to120 psi. Close cylinder valve and continue tobreathe normally. If supplied air is interrupted, opencylinder valve fully, unplug airline hose and thenegress to a safe area.9.3.1.8 Take necessary actions to monitor the supplied airsource pressure while operating with supplied air.9.3.1.9 To transfer from supplied air to cylinder air, opencylinder valve first. Disconnect supplied air hose byretracting coupling sleeve.9.3.2 ESCAPES AIR SYSTEM (EAS) DESCRIPTION,LIMITATIONS & OPERATIONNote: The EAS option is available on all models of thePull Down
COPYRIGHT 2007 AVON - ISI22International Safety Instruments, Inc. (AVON-ISI) warrantsthe VIKING SCBA to the original owner to be free from de-fects in materials and workmanship from the date of shipmentfrom AVON-ISI’s factory for 15 years of this product. To main-tain this warranty, the purchaser must perform maintenanceand inspections as prescribed in the owner’s instruction man-ual, which shall include prompt replacement or repair of de-fective parts, and replacement of parts per the maintenanceschedule as prescribed in the owner’s instruction manual.This warranty does not apply to expendable or consumableparts whose normal life expectancy is less than one (1) year.AVON-ISI’s obligation under this warranty is limited to replac-ing or repairing, at AVON-ISI’s option, any defective part if re-turned to AVON-ISI in Lawrenceville, GA, or an AVON-ISI au-thorized service center. Shipping charges are to be prepaidby the buyer. Upon inspection, AVON-ISI will repair all prod-ucts that prove to have been defective due to defects in ma-terials and/or workmanship. AVON-ISI shall be released fromall obligations under this warranty in the event repairs ormodifications are made by persons other than its own or au-thorized service personnel, or if the warranty claim resultsfrom misuse of the product.AVON-ISI warrants the Viking Digital’s solid- state compo-nents to be free from defects in workmanship and materialsfor a period of one (1) year from the date of purchase.In addition, this warranty does not apply to elastomer or rub-ber components since they can be adversely affected by un-due exposure to heat, sun, water, chemicals, ozone, or otherdeteriorating elements. Also excluded from this warranty arefacemask lenses, compressed-air cylinders and parts that be-come defective through normal use. The decision as to whatconstitutes normal use shall be made solely by AVON-ISI.AVON-ISI will not repair or replace under warranty any mer-chandise that has been damaged from accident, alteration,misuse, or abuse while in the possession of the end-user.AVON-ISI shall not be liable for any direct, incidental or otherconsequential loss or damage arising out of the failure of thedevice to operate.THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHERWARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY,AND IS STRICTLY LIMITED TO THE TERMS HEREOF.AVON-ISI SPECIFICALLY DISCLAIMS ANY WARRANTY OFMERCHANTABILITY OR OF FITNESS FOR A PARTICULARPURPOSE. AVON-ISI neither assumes nor authorizes anyother person or firm to assume on AVON-ISI’s behalf any lia-bility in any way connected with the sale of AVON-ISI prod-ucts.To validate this warranty, the Warranty & Registration Cardsupplied with the apparatus MUST be detached, completed,and returned to AVON-ISI WITHIN 30 DAYS of purchase.10.0 VIKING SCBA WARRANTY
COPYRIGHT 2007 AVON - ISI 23If corrections by a Certified AVON-ISI Service Technician DO NOT resolve theproblem, tag the unit "Out of Service" and have the SCBA serviced by anAVON-ISI Certified Service Center.Pressure Display on wrong setting.May be on 2216 (low pressure) when4500 (high pressure) unit.Lights in the facemask turn onslowly as cylinder is opened. Badtransducer1. Radio2. Interface lead1. Facemask board2. Bad speaker or speaker wire3. Control Console4. Turn VAS "on"Poor facemask electronics contactTwo lights "on" with full cylinderCylinder pressure, slow reactingRadio interface interferenceVAS not workingVAS with static noiseTurn on Control Console and checkpressure: should read "22" for lowpressure and "45" for high pressure. Ifon wrong setting, remove battery pack,push and hold in PTT button andinstall battery pack. Cycle back andforth using PTT buttonTag for repair1. Check radio on another Viking2. Check interface lead on anotherViking. If background noise, touchlead at Viking connection to groundconnection. If noise stops, need newinterface lead.1. Tag for repair2. Tag for repair3. Tag for repair4. Tag for repairLubricate facemask electronics plugwith diolectric grease.PROBLEM POSSIBLE CAUSE CORRECTION11.0 TROUBLESHOOTING GUIDENote: Only AVON-ISI trained technicians are qualified to perform repairs that require any adjustments or replacement of parts. Thistroubleshooting guide is to help aid the user in determining the cause of the problem and not meant to be a quick guide in doing repairs.
COPYRIGHT 2007 AVON - ISITABLE OF CONTENTSPREFACE-IMPORTANT POINTS 1Intent 1Training 1Approvals 1NIOSH warnings 1Cautions and Limitations 2Special or Critical User Instructions 21.0 DESCRIPTION OF VIKING SCBA 31.1 Facemask 31.2 AirSwitch Regulator 31.3 RDV Regulator 31.4 First Stage Pressure Reducer 31.5 End-of-Service Alarms 41.6 Backframe and Harness 41.7 Control Console 41.8 Cylinder and Valve Assembly 41.9 Rapid Intervention Crew Fitting 51.10 Viking Cylinder Table 52.0 ROUTINE CHECKS 62.1 Unpacking 62.2 Inventory and Examination 62.3 Routine Checks and Inspections 62.4 SCBA Retirement 73.0 DONNING PROCEDURES AND SAFETYCHECKS 83.1 Donning Procedures 83.2 Safety Checks 104.0 DURING USE 114.1 Reading the Heads-Up Display 114.2 Normal Use 124.3 CBRN Specific Actions 124.4 Instructions for Changing Cylinders 124.5 Cylinder Band Adjustment 124.6 Emergency Egress Indicators 124.7 RIC Fitting Procedures 135.0 AFTER USE PROCEDURES 145.1 Doffing 146.0 AFTER USE CLEANING AND CYLINDERCHANGING 156.1 Clean AirSwitch Regulator/Facemask 156.2 Clean RDV Facemask 156.3 Cleaning SCBA 157.0 SCBA STORAGE 167.1 SCBA Storage 168.0 USER MAINTENANCE 168.1 Maintenance Intervals 168.2 Cylinder Filling Procedures 168.3 Battery Pack 168.4 Facemask Harness Replacement 178.5 Backframe Harness Removal 179.0 VIKING OPTIONS 189.1 Control Console Keys & Functions 189.2 Stealth Mode 209.3 Additional Options 2010.0 WARRANTY 2211.0 TROUBLESHOOTING GUIDE 23
COPYRIGHT 2007 AVON - ISIViking Z SEVEN SCBAUser's ManualAVON- ISI922 Hurricane Shoals RoadLawrenceville, GA 30043Phone: 770-962-2552Fax: 770-963-2797www.intsafety.comPart Number: 084126 Rev. AArtwork Number: A49257 Rev. AFebruary 19, 2007ISO 9001 Certified WARNINGDisassembly of the components beyond the procedures described herein shall not beperformed. Additional disassembly may cause component damage and shall only be per-formed by ISI authorized personnel or the factory.VIKING Z SEVEN CBRN MODELSVIKING Z SEVEN CBRN MODELSVIKING Z SEVEN CBRN MODELSVIKING Z SEVEN CBRN MODELSVIKING Z SEVEN CBRN MODELSVIKING Z SEVEN 2216 PSI, 30 MINUTENIOSH APPROVAL TC-13F-XXXVIKING Z SEVEN 4500 PSI, 30 MINUTENIOSH APPROVAL TC-13F-XXXVIKING Z SEVEN, 4500 PSI, 45 MINUTENIOSH APPROVAL TC-13F-XXXVIKING Z SEVEN, 4500 PSI, 60 MINUTENIOSH APPROVAL TC-13F-XXXAVON - ISI

Navigation menu