Samsung Electro Mechanics CEMF11G01G0101 LTE Full Mini card Module User Manual SWL A70U Datasheet

Samsung Electro Mechanics LTE Full Mini card Module SWL A70U Datasheet

User manual

CEMF11G01G0101 User manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 1/8 CEMF11G01G0101 User Manual GCT GDM7240R1 LTE Solution REV 0.1 Samsung Electro-Mechanics 2011-11-11 Summary This description presents the general specifications of CEMF11G01G0101 which designed for 3GPP LTE Band 13. © 2011 Samsung Electro-Mechanics. All rights reserved The names of actual companies and products mentioned herein may be the trademarks of their respective owners. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Samsung Electro-Mechanics. This document is subject to change without notice.
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 2/8 1 Electrical Characteristics 1.1 Power Supply The CEMF11G01G0101 must be connected to a 3.3V power supply by PCI Express® Mini Card Electromechanical Specification Revision 1.2 Compliant. Requirement type Value Power Supply 3.3V Voltage range 3.1 ~ 3.6V Maximum Current (Max Power +23dBm) 850mA Table 1-1. Power Supply Requirements 1.2 General Characteristics Item LTE Remark Current consumption Typ. 180mA Connect with PC, With Test JIG Radio Frequency Tx : 777 ~ 787MHz Rx : 746 ~ 756MHz Band 13 Bandwidth 10MHz Frequency Type Earcfn DL : 5230 / UL : 23230 Maximum Throughput DL : 100Mbps UL : 50Mbps Category 3 Modulation Format DL : QPSK, 16QAM, 64QAM UL : QPSK, 16QAM Antenna Configuration 2 Rx Diversity 1 Tx - Main 2 Rx – Main, Diversity Table 1-2. General Characteristics M & SOFT AMERICA MAP CENTERTEL : 888-757-0010WEBSITE : www.mapnsoft.comMAP DATABASE HOTLINEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ,&:DUQLQJ7KLVGHYLFHFRPSOLHVZLWK,QGXVWU\&DQDGDOLFHQFHH[HPSW566VWDQGDUGV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQVWKLVGHYLFHPD\QRWFDXVHLQWHUIHUHQFHDQGWKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQRIWKHGHYLFH/HSUpVHQWDSSDUHLOHVWFRQIRUPHDX[&15G,QGXVWULH&DQDGDDSSOLFDEOHVDX[DSSDUHLOVUDGLRH[HPSWVGHOLFHQFH/H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQVVXLYDQWHVODSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJHHWOXWLOLVDWHXUGHODSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPrPHVLOHEURXLOODJHHVWVXVFHSWLEOHGHQFRPSURPHWWUHOHIRQFWLRQQHPHQW This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC. M & SOFT AMERICA MAP CENTERTEL : 888-757-0010WEBSITE : www.mapnsoft.comMAP DATABASE HOTLINEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ,&:DUQLQJ7KLVGHYLFHFRPSOLHVZLWK,QGXVWU\&DQDGDOLFHQFHH[HPSW566VWDQGDUGV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQVWKLVGHYLFHPD\QRWFDXVHLQWHUIHUHQFHDQGWKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQRIWKHGHYLFH/HSUpVHQWDSSDUHLOHVWFRQIRUPHDX[&15G,QGXVWULH&DQDGDDSSOLFDEOHVDX[DSSDUHLOVUDGLRH[HPSWVGHOLFHQFH/H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQVVXLYDQWHVODSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJHHWOXWLOLVDWHXUGHODSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPrPHVLOHEURXLOODJHHVWVXVFHSWLEOHGHQFRPSURPHWWUHOHIRQFWLRQQHPHQW This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 3/8 1.3 Storage Condition It needs proper condition for protecting the rust. - Temperature : 0 ~ +50°C - Humidity : lower level recommended, 25% ~ 65%RH - Max Storage Limit : Within 6 month form production
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 4/8 2 RF Specification 2.1 LTE Specification All measurements are made under nominal power supply and room temperature 25°C unless specified. Test Item Min Typ Max Unit Remark Tx Maximum Output Power +21.3 +23 +25.7 dBm No MPR +19.3 With MPR Occupied Bandwidth 0 10 MHz Spectrum Emission Mask -16.5 dB ΔfOOB : 15 ~ 85KHz -11.5 ΔfOOB : 150 ~ 950KHz -11.5 ΔfOOB : 1.5 ~ 9.5MHz -23.5 ΔfOOB : 10.5 ~ 14.5MHz ACLR_EUTRA -30 dB ACLR_UTRA -33 dB Freq Offset : 5MHz -36 Freq Offset : 15MHz Transmit Signal Quality EVM 0 17.5 % QPSK 12.5 16QAM Frequency Error -0.1 0.1 ppm IQ Offset -999 -25 dBc Rx Sensitivity 0 5 % @ -95dBm RSSI -34 -30 -26 dBm Main, Div -54 -50 -46 -84 -80 -76 Table 2-1. LTE RF Specification
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 5/8 2.2 Antenna Connection  2 RF Port : U.FL Connector Main ANT Connector : 1EA AUX ANT Connector : 1EA - Main ANT Connector is sharing the Tx and Rx. Figure 2-1. Antenna Connector Mechanical Dimension Attaching an antenna to the CEMF11G01G0101 :  Use a Hirose U.FL connector (Part No. : U.FL-R-SMT, CL No. : 331-0471-0-10) to attach an antenna to a connection point on the CEMF11G01G0101.  Match coaxial connections between the CEMF11G01G0101 and the antenna to 50 Ω.  Minimize RF cable losses between the CEMF11G01G0101 and the antenna to less than 0.5 dB. 2.3 Ground Connection Connecting the CEMF11G01G0101 to system ground :  Connect to system ground for preventing noise leakage.  Connect with host connector, two mounting holes, and PCI express® mini card connector.
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 6/8 3 Label Information 3.1 Module Label The Label contains Model Name, Product Code, FCC ID, IMEI and Serial Number. Figure 3-1. Module Label Information 3.1.1 S/N(Serial Number) Ex) S N F B 000001     S N F B 000001      Company S: Samsung Custom Model N : CEMF11G01G0101 Year F:2011 G:2012 Month 1~9:Jan~SEP A:OCT, B:Nov, C:Dec Serial No 000001 ~ FFFFFF (HEX) Table 3-1. Serial Number Information M & SOFT AMERICA MAP CENTERTEL : 888-757-0010WEBSITE : www.mapnsoft.comMAP DATABASE HOTLINEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ,&:DUQLQJ7KLVGHYLFHFRPSOLHVZLWK,QGXVWU\&DQDGDOLFHQFHH[HPSW566VWDQGDUGV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQVWKLVGHYLFHPD\QRWFDXVHLQWHUIHUHQFHDQGWKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQRIWKHGHYLFH/HSUpVHQWDSSDUHLOHVWFRQIRUPHDX[&15G,QGXVWULH&DQDGDDSSOLFDEOHVDX[DSSDUHLOVUDGLRH[HPSWVGHOLFHQFH/H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQVVXLYDQWHVODSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJHHWOXWLOLVDWHXUGHODSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPrPHVLOHEURXLOODJHHVWVXVFHSWLEOHGHQFRPSURPHWWUHOHIRQFWLRQQHPHQW This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 7/8 6 Safety Information 6.1 Certification FCC ID : E2XCEMF11G01G0101 Warning: Exposure to Radio Frequency Radiation The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20 cm during normal operation. The gain of the antenna for LTE band must not exceed 0 dBi. FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation. 6.2 Caution Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. M & SOFT AMERICA MAP CENTERTEL : 888-757-0010WEBSITE : www.mapnsoft.comMAP DATABASE HOTLINEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ,&:DUQLQJ7KLVGHYLFHFRPSOLHVZLWK,QGXVWU\&DQDGDOLFHQFHH[HPSW566VWDQGDUGV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQVWKLVGHYLFHPD\QRWFDXVHLQWHUIHUHQFHDQGWKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQRIWKHGHYLFH/HSUpVHQWDSSDUHLOHVWFRQIRUPHDX[&15G,QGXVWULH&DQDGDDSSOLFDEOHVDX[DSSDUHLOVUDGLRH[HPSWVGHOLFHQFH/H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQVVXLYDQWHVODSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJHHWOXWLOLVDWHXUGHODSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPrPHVLOHEURXLOODJHHVWVXVFHSWLEOHGHQFRPSURPHWWUHOHIRQFWLRQQHPHQW This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
CEMF11G01G0101 User Manual REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 8/8 M & SOFT AMERICA MAP CENTERTEL : 888-757-0010WEBSITE : www.mapnsoft.comMAP DATABASE HOTLINEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ,&:DUQLQJ7KLVGHYLFHFRPSOLHVZLWK,QGXVWU\&DQDGDOLFHQFHH[HPSW566VWDQGDUGV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQVWKLVGHYLFHPD\QRWFDXVHLQWHUIHUHQFHDQGWKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQRIWKHGHYLFH/HSUpVHQWDSSDUHLOHVWFRQIRUPHDX[&15G,QGXVWULH&DQDGDDSSOLFDEOHVDX[DSSDUHLOVUDGLRH[HPSWVGHOLFHQFH/H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQVVXLYDQWHVODSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJHHWOXWLOLVDWHXUGHODSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPrPHVLOHEURXLOODJHHVWVXVFHSWLEOHGHQFRPSURPHWWUHOHIRQFWLRQQHPHQW This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. d your body. )RUODEHOUHTXLUHPHQWZKHQWUDQVPLWWHUPRGXOHLVLQVWDOOHGLQDKRVWWKHKRVWVKDOOKDYHDQDGGLWLRQDOSHUPDQHQWODEHOUHIHUULQJWRWKHHQFORVHGPRGXOH³&RQWDLQV7UDQVPLWWHU0RGXOH)&&,'%(-7:)0%'´)RUODEHOUHTXLUHPHQWZKHQWUDQVPLWWHUPRGXOHLVLQVWDOOHGLQDKRVWWKHKRVWVKDOOKDYHDQDGGLWLRQDOSHUPDQHQWODEHOUHIHUULQJWRWKHHQFORVHGPRGXOH³&RQWDLQV7UDQVPLWWHU0RGXOH)&&,'%(-7:)0%'´T7KLVUDGLRFDQQRWEHLQVWDOOHGLQKRVWZKHUHFRORFDWHGRURSHUDWLQJLQFRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRUWUDQVPLWWHUhis transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC. GGFor label requirement when transmitter module is installed in a host, the host shall have an additional permanent label referring to the enclosed module “Contains Transmitter Module FCC ID: lYjltmXXnWXnWXWX”

Navigation menu