Samsung Electro Mechanics CEMF11G01G0101 LTE Full Mini card Module User Manual SWL A70U Datasheet
Samsung Electro Mechanics LTE Full Mini card Module SWL A70U Datasheet
User manual
CEMF11G01G0101 User manual CEMF11G01G0101 User Manual GCT GDM7240R1 LTE Solution REV 0.1 Samsung Electro-Mechanics 2011-11-11 Summary This description presents the general specifications of CEMF11G01G0101 which designed for 3GPP LTE Band 13. Š 2011 Samsung Electro-Mechanics. All rights reserved The names of actual companies and products mentioned herein may be the trademarks of their respective owners. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Samsung Electro-Mechanics. This document is subject to change without notice. REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 1/8 CEMF11G01G0101 User Manual 1 Electrical Characteristics 1.1 Power Supply The CEMF11G01G0101 must be connected to a 3.3V power supply by PCI ExpressÂŽ Mini Card Electromechanical Specification Revision 1.2 Compliant. Requirement type Value Power Supply 3.3V Voltage range 3.1 ~ 3.6V Maximum Current (Max Power +23dBm) 850mA Table 1-1. Power Supply Requirements 1.2 General Characteristics Item LTE Remark Current consumption Typ. 180mA Connect with PC, With Test JIG Radio Frequency Tx : 777 ~ 787MHz Bandwidth 10MHz Frequency Type Earcfn Maximum Throughput Modulation Format Antenna Configuration Band 13 Rx : 746 ~ 756MHz DL : 100Mbps UL : 50Mbps DL : 5230 / UL : 23230 Category 3 DL : QPSK, 16QAM, 64QAM UL : QPSK, 16QAM 2 Rx Diversity 1 Tx - Main 2 Rx â Main, Diversity Table 1-2. General Characteristics REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 2/8 CEMF11G01G0101 User Manual 1.3 Storage Condition It needs proper condition for protecting the rust. REV 0.1 Temperature : 0 ~ +50°C Humidity : lower level recommended, 25% ~ 65%RH Max Storage Limit : Within 6 month form production Samsung Electro-Mechanics Proprietary and Confidential 3/8 CEMF11G01G0101 User Manual 2 RF Specification 2.1 LTE Specification All measurements are made under nominal power supply and room temperature 25°C unless specified. Test Item Min Maximum Output Power Occupied Bandwidth +21.3 +19.3 Typ Max Unit +23 +25.7 dBm 10 MHz Remark No MPR With MPR ÎfOOB : 15 ~ 85KHz -16.5 Tx -11.5 Spectrum Emission Mask -11.5 dB -30 -33 ACLR_UTRA Transmit Signal Quality Rx -36 17.5 ÎfOOB : 1.5 ~ 9.5MHz ÎfOOB : 10.5 ~ 14.5MHz -23.5 ACLR_EUTRA ÎfOOB : 150 ~ 950KHz dB dB Freq Offset : 5MHz Freq Offset : 15MHz Frequency Error -0.1 0.1 ppm IQ Offset -999 -25 dBc Sensitivity @ -95dBm dBm Main, Div RSSI 12.5 -34 -30 -26 -54 -50 -46 -84 -80 -76 QPSK EVM 16QAM Table 2-1. LTE RF Specification REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 4/8 CEMF11G01G0101 User Manual 2.2 Antenna Connection 2 RF Port : U.FL Connector ďŹ Main ANT Connector : 1EA AUX ANT Connector : 1EA - Main ANT Connector is sharing the Tx and Rx. Figure 2-1. Antenna Connector Mechanical Dimension Attaching an antenna to the CEMF11G01G0101 : ďŹ Use a Hirose U.FL connector (Part No. : U.FL-R-SMT, CL No. : 331-0471-0-10) to attach an antenna to a connection point on the CEMF11G01G0101. ďŹ Match coaxial connections between the CEMF11G01G0101 and the antenna to 50 âŚ. ďŹ Minimize RF cable losses between the CEMF11G01G0101 and the antenna to less than 0.5 dB. 2.3 Ground Connection Connecting the CEMF11G01G0101 to system ground : ďŹ Connect to system ground for preventing noise leakage. ďŹ Connect with host connector, two mounting holes, and PCI expressÂŽ mini card connector. REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 5/8 CEMF11G01G0101 User Manual 3 Label Information 3.1 Module Label The Label contains Model Name, Product Code, FCC ID, IMEI and Serial Number. Figure 3-1. Module Label Information 3.1.1 S/N(Serial Number) Ex) S N F B 000001ď ď ď ď ď 000001 ď ď ď ď ď Company S: Samsung Custom Model N : CEMF11G01G0101 Year F:2011 G:2012 Month 1~9:Jan~SEP A:OCT, B:Nov, C:Dec Serial No 000001 ~ FFFFFF (HEX) Table 3-1. Serial Number Information REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 6/8 CEMF11G01G0101 User Manual 6 Safety Information 6.1 Certification FCC ID : E2XCEMF11G01G0101 Warning: Exposure to Radio Frequency Radiation The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20 cm during normal operation. The gain of the antenna for LTE band must not exceed 0 dBi. FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation. 6.2 Caution Modifications not expressly approved by the party responsible for compliance could void the userâs authority to operate the equipment. REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 7/8 CEMF11G01G0101 User Manual This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Ë Reorient or relocate the receiving antenna. Ë Increase the separation between the equipment and receiver. Ë Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Ë Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modiďŹcations to this device not explicitly approved by manufacturer could void your authority to operate this equipment. d your body. For label requirement when transmitter module is installed in a host, G )RUODEHOUHTXLUHPHQWZKHQWUDQVPLWWHUPRGXOHLVLQVWDOOHGLQDKRVWWKHKRVWVKDOOKDYHDQDGGLWLRQDOSHUPDQHQWODEHOUHIHUULQJWRWKHHQFORVHGPRGXOHÂł&RQWDLQV7UDQVPLWWH the host shall have an additional permanent label referring to the enclosed module âContains Transmitter Module FCC ID: lYjltmXXnWXnWXWXâ REV 0.1 Samsung Electro-Mechanics Proprietary and Confidential 8/8
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Samsung Electro-Mechanics Create Date : 2011:11:17 14:24:43Z Keywords : SWL-A70U, Datasheet Modify Date : 2011:11:28 14:53:07+09:00 Subject : SWL-A70U Datasheet Has XFA : No Language : ko-KR Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : Samsung Electro-Mechanics Description : SWL-A70U Datasheet Title : SWL-A70U Datasheet Creator Tool : Microsoft® Office Word 2007 Metadata Date : 2011:11:28 14:53:07+09:00 Producer : Microsoft® Office Word 2007 Document ID : uuid:1e298021-ec46-4d18-8ee2-4d1e8405bedc Instance ID : uuid:a4773e9b-8a1f-40dd-b094-186bf59fe036 Page Count : 8EXIF Metadata provided by EXIF.tools