Samsung Electronics Co ATKM102000 ARTIK-1020 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3013873
Application ID	PKI4arqj7Rf5EU64ZRGIaQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	81.54kB (1019302 bits)
Date Submitted	2016-06-01 00:00:00
Date Available	2016-12-18 00:00:00
Creation Date	2016-05-04 16:19:19
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2016-05-26 09:39:50
Document Title	User Manual
Document Creator	Microsoft® Office Word 2007
Document Author:	Z420

ARTIK 10 User Manual
FCC ID: A3LATKM102000
IC: 649E-ATKM102000
Model: ATKM102000
1. ARTIK 10 RF PART Circuit Description
1.1 ZIGBEE
: EM3587(U206)
The Ember EM3587 is a fully integrated System-on-Chip that integrates a 2.4 GHz, IEEE 802.15.42003-compliant transceiver, 32-bit ARM® CortexTM-M3 microprocessor, flash and RAM memory,
and peripherals of use to designers of ZigBee-based systems.
 32-bit ARM® Cortex -M3 processor
 2.4 GHz IEEE 802.15.4-2003 transceiver & lower MAC
 256 or 512 kB flash, with optional read protection
 32 or 64 kB RAM memory
 AES128 encryption accelerator
 Flexible ADC, UART/SPI/TWI serial communications, and general purpose timers
 Optional USB serial communications
 24 highly configurable GPIOs with Schmitt trigger inputs
1.2 WLAN/BT : SWB-B80(U208)
SWB-B80 is the combo module for IEEE 802.11 a/b/g/n/ac Wireless LAN with 2x2 MIMO support
and Bluetooth 4.1 + LE at embedded and mobile applications. It is based on Broadcom BCM4354
solution which comprises single chip dual band IEEE 802.11 a/b/g/n/ac 2x2 MAC/Baseband/Radio
with integrated Bluetooth 4.1 + LE. • Wireless local area network (WLAN) compliant with the IEEE
802.11 b/g/n specification

WLAN - IEEE 802.11ac Draft compliant
Dual-stream spatial multiplexing up to 867Mbps data rate
Supports 20, 40, and 80MHz channels with optional SGI (256 QAM modulation)
Full IEEE 802.11 a/b/g/n legacy compatibility with enhanced performance
Tx/Rx low-density parity check (LDPC) support for improved range and power efficiency
Support IEEE 802.11ac/n beamforming
Bluetooth – Bluetooth 4.1 + LE
Bluetooth Class 1 or Class 2 transmitter operation
Low power consumption
Compact dimension: 9.20 x 5.70mm / Hmax : 1.20 mm
Host Interfaces: SDIO v3.0 for WLAN, UART/PCM for Bluetooth
RoHS compliant
2. ARTIK 10 Baseband Circuit Description
2.1 AP : S5E5422(U1)
Exynos 5422 is a system-on-a-chip (SoC) based on the 32-bit RISC processor for Smartphone
tablet, laptop, and desktop PCs. Designed with the 28 nm low power HKMG process, Exynos 5422
provides the best performance features such as CORTEX-A15 quad and CORTEX-A7 quad core
CPU, highest memory bandwidth, WQXGA display, 1080p 60 fps (frames per second) video
decoding and encoding hardware, 3D graphics hardware, image signal processor, and high-speed
interfaces such as eMMC5.0, and USB 3.0.
ARM Cortex-A15 Quad CPU (Eagle) with NEON as high performance processor
32 KB (Instruction)/32 KB (Data) Cache and 2 MB L2 Cache
ARM Cortex-A7 Quad CPU (Kingfisher) as power-efficient performance processor
32 KB (Instruction)/32 KB (Data) Cache and 512 KB L2 Cache
128-bit Multi-layer Network-on-Chip (NoC) architecture
Cache Coherent Interface (CCI) among Cortex-A15 and Cortex-A7, G2D, G3D and SSS
Memory Subsystem:
2-ports 32-bit up to 933 MHz LPDDR3/DDR3 Interfaces
2-ports 32-bit up to 533 MHz LPDDR2 Interfaces
Multi-format Video Hardware codec (MFC): 1920x1080@120fps (capable of decoding and encoding MPEG4/H.263/H.264/VP8 and decoding of MPEG-2/VC1 video) and upto 8192x8192 H.264 and VP8
encoding/decoding
2.2 Memory : KLMAG2GEAC-B002 (U6)
The Samsung KLMAG2GEAC-B002 is a 16 GB eMMC flash memory

embedded MultiMediaCard Ver. 4.5 compatible. Detail description is referenced by JEDEC Standard
SAMSUNG e·MMC supports features of eMMC4.5 which are defined in JEDEC Standard
Supported Features : Packed command, Cache, Discard, Sanitize, Power Off Notification, Data Tag,
Partition types,
Context ID, Real Time Clock, Dynamic Device Capacity, HS200
Non-supported Features : Large Sector Size (4KB)
 Additional feature : DDR400 mode (200MHz DDR - up to 400Mbps)
Full backward compatibility with previous MultiMediaCard system specification (1bit data bus, multi-e·MMC
systems)
 Data bus width : 1bit (Default), 4bit and 8bit
MMC I/F Clock Frequency : 0 ~ 200MHz
MMC I/F Boot Frequency : 0 ~ 52MHz
Temperature : Operation (-
Power : Interface power → VDD(VCCQ) (1.70V ~ 1.95V or 2.7V ~ 3.6V) , Memory power → VDDF(VCC)
(2.7V ~ 3.6V)
2.3 PMIC : S2MPS11B02(S2MPS11B2) (U4)
S2MPS11 is an advanced Power Management IC (PMIC) designed for mobile applications.
S2MPS11, coupled with Multi Core Samsung Application Processors (Exynos5410), is used in a
wide variety of mobile applications such as smart phones and tablet PCs.

-Efficiency and programmable Buck Converters (1 Dual Phase Buck)

-Efficiency and programmable Buck-Boost Converter





al Shutdown / BandGap Reference


-on Sequence

3. ARTIK 10 Antenna Description
Antenna information can be found at the link below.
https://developer.artik.io/documentation/getting-started-beta/antenna-locations.html
MODULE DISCLOSURES – QUICK START GUIDE
FCC REGULATORY DISCLOSURES
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two
Conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesirable operation
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the
transmitter’s radiating structure(s) and the body of the user or nearby persons.
This module is intended for OEM integration. The OEM integrator is responsible for FCC compliance and
compliance with all applicable regulations including those for modular transmitters 47 C.F.R. 15.212.
The OEM product must comply with all applicable labeling requirements including those contained in 15
C.F.R. 15.19. The OEM is solely responsible for certification and testing and labeling of its own products.
In addition to any independently required labels, the OEM shall also affix to the outside of a device into
which the module is installed a label referring to the enclosed module. This exterior label should be
prepared in a legible font and permanently affixed and using the wording “Contains Transmitter Module
FCCID: [A3LATKM102000]
The OEM is required to ensure that the end product integrates this module so as to maintain a minimum
distance of 20 cm between the equipment’s radiating structure(s) and the body of the user or nearby
persons. The OEM shall also advise its end user of this requirement as required by applicable rules.
The OEM shall require that the end user of its product be informed that the FCC radio frequency
exposure guidelines for an uncontrolled environment can be satisfied. The OEM shall further inform its
DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM
end user that any change or modifications to this module not expressly approved by the manufacturer
will void the warranty and the users’ authority to operate the equipment.
INDUSTRY CANADA REGULATORY DISCLOSURES
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est
soumise aux deux conditions suivantes:(1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.
INDUSTRY CANADA RADIATION EXPOSURE STATEMENT AND LIMITATIONS ON USE
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm between
the radiator and your body. This equipment should be installed and must not be co-located or operating
in conjunction with any other antenna or transmitter.
This equipment is restricted to indoor use in the 5.15-5.25 GHz range. This equipment is not able to be
operated at 5600-5650. In the United States and Canada, only Channel 1~11 can be operated and these
channel assignments deal only with the 2.4 GHz range.
The end product must be labeled to display the Industry Canada certification number of the module.
“Contains transmitter module IC: 649E-ATKM102000”
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada
du module.
Contient module émetteur IC : 649E-ATKM102000
DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM
EU REGULATORY DISCLOSURES
CE STATEMENT *
The following statement must be supplied with each product but can be printed in the user manual, the
packaging, or provided as a separated leaflet.
Hereby, Samsung declares that this IoT Module is in compliance with the essential requirements
and other relevant provisions of Article 3 of the R&TTE Directive 1999/5/EC, 2004/108/EC and
RoHS directive 2011/65/EU.
“The declaration of conformity may be consulted at [www.artik.io/]”
DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Z420
Create Date                     : 2016:05:04 16:19:19+09:00
Modify Date                     : 2016:05:26 09:39:50+09:00
Has XFA                         : No
Language                        : ko-KR
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Z420
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2016:05:26 09:39:50+09:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:4046a26d-9670-40c0-9142-94918dc4432d
Instance ID                     : uuid:702ec116-b3bb-493e-9f2c-cb196f19c6c5
Page Count                      : 6

EXIF Metadata provided by EXIF.tools