Samsung Electronics Co CSE783 17 INCHES MONITOR User Manual
Samsung Electronics Co Ltd 17 INCHES MONITOR
USER MANUAL
CSE 7839L
Color Monitor
Owner’s
Instructions
CSH7839-E 10/8/98 10:29 AM Page i
ii
C A U T I O N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and servicing instructions in the literature
accompanying the appliance.
Unpacking your Monitor
Please make sure the following items are included with
your computer monitor:
Monitor and Stand
Power Cable
This Manual
Warranty Card
(Not available in all
areas)
Signal Cable
CSH7839-E 10/8/98 10:29 AM Page ii
1
Table of Contents
Preface: Safety Information . . . . . . . . . .2
Chapter One: Overview of Your
Monitor . . . . . . . . . . . . . . . . . . . . . . . . .3
Front Panel.....................................................................................3
Rear Panel......................................................................................4
Chapter Two: Installation . . . . . . . . . . . . .5
Connecting Your Monitor to a Computer ..................................5
Chapter Three: Adjusting Your Monitor . .6
Overview........................................................................................6
Brightness......................................................................................6
Contrast..........................................................................................6
Direct Access Features...............................................................7
Position....................................................................................7
Size...........................................................................................7
Pincushion/Trapezoid............................................................7
Parallel/Rotation....................................................................8
Menu Features..............................................................................8
Color temperature .................................................................8
Color Control...........................................................................9
Degauss...................................................................................9
Recall.......................................................................................9
Menu Position......................................................................10
Menu Duration.....................................................................10
D-SUB / BNC ........................................................................11
Pinbalance............................................................................11
Clear Moire...........................................................................11
Language ..............................................................................12
Display Timing ......................................................................12
Video Input Level.................................................................12
Sync. Input Type...................................................................13
Exit..........................................................................................13
PowerSaver.................................................................................14
Troubleshooting..........................................................................15
A p p e n d i x . . . . . . . . . . . . . . . . . . . . . . . . .1 6
Specifications..............................................................................16
Pin Assignments.........................................................................17
Display Modes Timing Chart.....................................................18
CSH7839-E 10/8/98 10:29 AM Page 1
Preface: Safety Information
2
Please read and follow these instruc-
tions when connecting and using your
computer monitor.
1Before connecting the AC power
cord to an outlet, make sure the
voltage designation on your moni-
tor corresponds to the local elec-
trical supply.
2Never insert anything metallic into
the monitor openings. Doing so
may create the danger of electric
shock.
3To avoid electric shock, never
touch the inside of the monitor.
Only a qualified technician should
open the monitor’s case.
4Never use your monitor if the
power cord has been damaged.
Do not allow anything to rest on
the power cord, and keep the cord
away from where people could
trip over it.
5Be sure to hold the plug, not the
cord, when disconnecting the
monitor from an electric socket.
6Openings in the monitor cabinet
are provided for ventilation. To
prevent overheating, these open-
ings should not be blocked or cov-
ered. Also, avoid using the monitor
on a bed, sofa, rug, or other soft
surface. Doing so may block the
ventilation openings in the bottom
of the cabinet. If you put the moni-
tor in a bookcase or some other
enclosed space, be sure to pro-
vide adequate ventilation.
7Put your monitor in a location with
low humidity and a minimum of
dust. Avoid places like damp
basements or dusty hallways.
8Do not expose the monitor to rain
or use it near water (in kitchens,
next to swimming pools, etc.). If
the monitor accidentally gets wet,
unplug it and contact an autho-
rized dealer immediately. You can
clean the monitor with a damp
cloth when necessary, but be sure
to unplug the monitor first.
9Place the monitor on a solid sur-
face and treat it carefully. The
screen is made of glass and can
be damaged if dropped or sharply
hit.
10Locate your monitor near an easily
accessible AC outlet.
11If your monitor does not operate
normally – in particular, if there
are any unusual sounds or smells
coming from it – unplug it immedi-
ately and contact an authorized
dealer or service center.
12High temperatures can cause
problems. Don’t use your monitor
in direct sunlight, and keep it away
from heaters, stoves, fireplaces,
and other sources of heat.
13Unplug the monitor when it is
going to be left unused for an
extended period of time.
14Unplug your monitor from the AC
outlet before any service.
CSH7839-E 10/8/98 10:29 AM Page 2
Chapter One: Overview of Your Monitor
3
Front Panel
1,button
Use this button to adjust the position or size.
2, button
Use this button to adjust the pincushion/trapezoid
or parallel/rotation.
3▲,▼,$, % buttons
Use these buttons to choose or adjust items in the
on-screen display.
4, MENU button
Use this button to activate the on-screen display, to
enter a selection in the on-screen display, or to exit
the on-screen displays.
5Power indicator
This light glows green during normal operation, and
blinks amber once as your adjustments are saved.
6Power button
Use this button to turn the monitor on and off.
1 2 3 4
5 6
CSH7839-E 10/8/98 10:29 AM Page 3
4
Chapter One: Overview of Your Monitor
Rear Panel
1Power port
Connect the power cable here.
2Signal port
Connect your signal cable here.
3BNC signal port
Connect a BNC signal cable here. (BNC signal
cable not included)
3
12
CSH7839-E 10/8/98 10:29 AM Page 4
5
Chapter Two: Installation
Connecting Your Monitor
to a Computer
1Turn off your computer and unplug
its power cord.
2Connect the signal cable to the
D-SUB or BNC signal port on the
back of your monitor.
3If you are using a Macintosh com-
puter, connect the other end of the
signal cable to a Macintosh
adapter. (The adapter is not includ-
ed with your monitor. Contact your
dealer for more information.) If you
are using an IBM-compatible com-
puter, skip to step 5.
4Follow the instructions included
with your adapter to set the pins
on your adapter, if necessary.
5Connect the signal cable (with the
adapter if necessary) to the video
port on the back of your computer.
This port might be directly
attached to your computer, or it
might be part of a video board,
video card, or graphics card.
6Connect the power cord for your
monitor to the power port on the
back of the monitor.
7Plug the power cords of your com-
puter and your monitor into a near-
by outlet.
8Turn on your computer and mon-
itor. If your monitor displays an
image, installation is complete.
Note: You can download the monitor
driver from the internet at
http://www.sec.samsung.co.kr (Enter)
Select Support => File download =>
Monitor => your Monitor name.
For directions on completing the monitor
configuration process, click on install.txt
(Windows 95 driver installation guide).
2
6
7
3
5
CSH7839-E 10/8/98 10:29 AM Page 5
6
Overview
Your Samsung SyncMaster computer monitor allows you
to easily adjust the characteristics of the image being
displayed. All of these adjustments are made using the
control buttons on the front of the monitor. These buttons
operate the on-screen menu, which shows you the
monitor’s settings and allows you to change those set-
tings
1Brightness
This feature will adjust the overall brightness of the
display image. Rotate the rotary control to the right
to increase the level of brightness, or to the left to
decrease the brightness.
2Contrast
This feature will adjust the monitor’s contrast.
Rotate the rotary control to the right to increase the
contrast between dark colors and light colors, or
move it to the left to decrease the contrast.
Chapter Three: Adjusting Your Monitor
1 2
CSH7839-E 10/8/98 10:29 AM Page 6
7
Chapter Three: Adjusting Your Monitor
Direct-Access Features
The features described on this page can be accessed
quickly, at the touch of one button. Once you have adjust-
ed one of these features, push the button once or twice
to turn off the display.
Position
Follow these instructions to change the position of the
monitor’s entire display.
1With the menu off, push the button. The posi-
tion display will appear.
2Use the ▲and ▼buttons to change the vertical
position of the monitor’s entire display; use the $
and %buttons to change the horizontal position of
the monitor’s entire display.
Size
Follow these instructions to change the size of the moni-
tor’s entire display.
1With the menu off, push the button twice. The
size display will appear.
2Push the ▲or ▼buttons to change the vertical size
of the monitor’s display; push the $or %buttons to
change the horizontal size of the monitor’s display.
Pincushion/Trapezoid
Adjust the pincushion setting when the sides of the dis-
play are bowed in or bowed out; adjust the trapezoid set-
ting when the top or bottom of the display is too large or
too small.
1With the menu off, push the button. The
Pincushion/Trapezoid display will appear.
2Use the $button or %button to adjust the pincush-
ion setting; use the ▲button or ▼button to adjust
the trapezoid setting.
CSH7839-E 10/8/98 10:29 AM Page 7
8
Chapter Three: Adjusting Your Monitor
Parallel/Rotation
Adjust the parallelogram setting when the display is lean-
ing left or right; adjust the rotation setting when the entire
display is tilted left or right.
1With the menu off, push the button twice.
The parallelogram/rotation display will appear.
2Use the $button or %button to adjust the parallel
setting; use the ▲button or ▼button to adjust the
rotation setting.
Menu Features
The following features can all be accessed using your
monitor’s on-screen menu system. Follow the instructions
below to adjust the features.
Once you are finished making adjustments to a feature,
push the MENU button to return to the Main Menu, then
push MENU again to turn off the menu.
Color Temperature
Follow these steps to change the color temperature set-
ting. Color temperature is a measure of the “warmth” of
the image colors.
1With the menu off, push the MENU button. Push the
$button or %button until the “Color Temperature”
screen is displayed.
2Push the button. The color temperature
adjustment screen will appear.
3Use the $button or %button to adjust the color
temperature.
CSH7839-E 10/8/98 10:30 AM Page 8
9
Chapter Three: Adjusting Your Monitor
Color Control
You can change the settings of the saturation and hue of
the monitor’s display.
1With the menu off, push the MENU button. Push the
$button or %button until the “Color Control”
screen is displayed.
2Push the button. The color control adjust
screen will appear.
3Use the $button or %button to adjust the satura-
tion setting; use the ▲button or ▼button to
adjust the hue.
Degauss
The Degauss feature will remove color impurities caused
by magnetic fields. Do not use the Degauss feature more
than once within a 30-minute period.
1With the menu off, push the MENU button. Push the
$button or %button until the “Degauss” screen is
displayed.
2Push the button. The monitor will execute the
degauss function, then display the degaussing
screen.
3After a few seconds, the degauss main menu will
appear.
Note: The monitor may buzz momentarily, the image
colors may change and the image will jiggle for a
few seconds. These effects are normal.
Recall
Use the recall feature to reset these monitor settings to their
original levels: position, size, pincushion, trapezoid, parallel-
ogram, pinbalance, rotation, and clear moire .
1With the menu off, push the MENU button. Push the
$button or %button until the “Recall” screen is
displayed.
CSH7839-E 10/8/98 10:30 AM Page 9
10
2Push the button. The recall select screen will
appear.
3Push the $button to select “YES.” If you don’t want
to reset the monitor, use the %button to select
“NO.”
NOTE: If you have selected “YES,” all settings listed
above will be reset. All other settings will remain
the same.
CAUTION: This operation resets all of the data in the
user memory area for the current timing signal.
Menu Position
You can change the position where the menu appears on
your monitor.
1With the menu off, push the MENU button. Push the
$button or %button until the “Menu Position”
screen is displayed
2Push the button. The menu position adjustment
screen will appear.
3Use the ▲,▼,$or %buttons to place the menu in
the position you prefer.
Menu Duration
The menu will automatically turn off if no adjustments are
made for a certain time period. You can set the amount of
time the menu will wait before it turns off.
1With the menu off, push the MENU button. Push the
$button or %button until the “Menu Duration”
screen is displayed.
2Push the button. The menu duration selection
screen will appear.
3Use the $or %buttons to select 3, 7, 10, 20, or 50
seconds.
Chapter Three: Adjusting Your Monitor
CSH7839-E 10/8/98 10:30 AM Page 10
11
D-SUB / BNC
Use this menu to choose between the signal source con-
nected to the BNC connector input and the signal source
connected to the D-SUB connector input.
1With the menu off, push the MENU button. Push the
$button or %button until the “D-SUB / BNC”
screen is displayed.
2Push the button. The D-SUB / BNC select
screen will appear.
3Use the $botton or %buttons to select “BNC” or
“D-SUB”.
NOTE: When you are finished, wait few seconds and
the screen will blank then display the image from
the new signal source (other computer). An con-
nected to both inputs to use this function.
Pinbalance
Adjust the pinbalance setting when the sides of the dis-
play are bowed towards the left or right.
1With the menu off, push the MENU button. Push the
$button or %button until the “Pinbalance” screen
is displayed.
2Push the button. The pinbalance adjustment
screen will appear.
3Use the $button or %button to adjust the pinbal-
ance setting.
Clear Moire
A “moire” pattern can appear on your screen, looking like
a series of concentric circles or arcs. To eliminate this
pattern, adjust the clear moire.
1With the menu off, push the MENU button. Push the
$button or %button until the “Clear Moire”
screen is displayed.
2Push the button. The clear moire adjustment
screen will appear.
3Use the ▲,▼, $or %buttons to adjust moire is
cleared.
Chapter Three:Adjusting Your Monitor
CSH7839-E 10/8/98 10:30 AM Page 11
12
3
Language
Follow these steps to change the language used in the
menu. This adjustment only changes the language of the
monitor’s menu; it does not change the language of any
other software.
1With the menu off, push the MENU button. Push the
$button or %button until the “7 Languages”
screen is displayed.
2Push the button. The language selection
screen will appear.
3Use the ▲button or ▼ button to select the lan-
guage you would like to use.
Display Timing
This screen displays the settings that are available to
your monitor. This screen only displays this information;
you cannot select a new setting.
1With the menu off, push the MENU button. Push the
$button or %button until the “Display Timing”
screen is displayed.
2Push the button. The Factory Timing screen will
appear.
3Use the ▲button or ▼ button to display the user
and factory timing.
Video Input Level
This feature will select the video signal level.
1With the menu off, push the MENU button. Push the
$button or %button until the “Video Input Level”
screen is displayed.
2Push the button. The video input level select
screen will appear.
Chapter Three: Adjusting Your Monitor
CSH7839-E 10/8/98 10:30 AM Page 12
13
3Use the $or %buttons to select 0.7V or 1.0V.
NOTE: Some video cards use video singals higher
than 1.0V which causes the display to be very bright.
For those video cards should be selected 1.0V.
Sync. Input Type
Use this menu to set your monitor to the correct type of
synchronization. Select “Separate”if the computer is
sending a separate synchronization signal. Select “Sync.
On Green” if the computer expects the monitor to syn-
chronize with the green signal it sends. Refer to your
computer or video card user’s manual to determine the
correct setting.
1With the menu off, push the MENU button. Push the
$button or %button until the “Sync. Input Type”
screen is displayed.
2Push the button. The sync input type selection
screen will appear.
3Use the ▲button or ▼button to select “Separate”
or “Sync. On Green.”
Exit
Once you are finished making adjustments to a feature,
use this menu to turn off the menu.
1Once you are finished making adjustments to a fea-
ture, push the MENU button.
2Push the $button or %button until the “Exit”
screen is displayed.
3Push the MENU button to turn off the menu.
Chapter Three:Adjusting Your Monitor
CSH7839-E 10/8/98 10:30 AM Page 13
14
3
Chapter Three: Adjusting Your Monitor
PowerSaver
This monitor has a built-in power management system
called PowerSaver. This system saves energy by switch-
ing your monitor into a low-power mode when it has not
been used for a certain amount of time. The available
modes are “On,” “Standby,” “Suspend,” and “Off.”
This system operates with a VESA DPMS compliant
video card installed in your computer. You use a software
utility installed on your computer to set up this feature.
See the table below for details.
Power Saving function mode EPA/NUTEK
State Normal Standby mode Suspend mode / Power-off Mode /
Operation Position A1 Position A2
Horizontal Sync Active Inactive Active Inactive
Vertical Sync Active Active Inactive Inactive
Video Active Blanked Blanked Blanked
Power Green Amber Amber/Green Amber
Indicator Blinking Blinking
Power 130W (max.) 65W (nominal) Less than 15W Less than 5W
Consumption 100W (nominal)
NOTE: This monitor automatically returns to normal oper-
ation when horizontal and vertical sync return. This
occurs when you move the computer's mouse or press a
key on the keyboard.
This monitor is EPA ENERGY STAR®compliant and NUTEK
compliant when used with a computer equipped with
VESA DPMS functionality. If your computer system can-
not support a display power management function, you
can purchase an optional DPMS software program to
enable the power saving function. Please contact
Samsung or your dealer for more information.
For energy conservation, turn your monitor OFF when it is
not needed, or when leaving it unattended for long peri-
ods.
CSH7839-E 10/8/98 10:30 AM Page 14
15
Chapter Three: Adjusting Your Monitor
Troubleshooting
Before calling for service, check the information in this
section to see if you can remedy any problems yourself.
If you do need assistance, please call the phone number
on the warranty card, the phone number on the back
cover of this manual, or contact your dealer.
There is no screen image.
• Check to see that both the monitor and the
computer are plugged in and turned on.
Image area is lightened but No image
appears.
• Check the signal cable connection between the
computer and the monitor.
The image is too light or too dark.
• Adjust the Brightness or Contrast settings.
The image is too large or too small.
• Adjust the Size settings.
The colors are distorted with dark or
shadowed areas.
• Activate the Degauss feature.
The power indicator is amber,
amber/green, or blinking.
• The monitor is using its power management system.
Check the power management utility on your
computer.
CSH7839-E 10/8/98 10:30 AM Page 15
16
3
A p p e n d i x
Specifications
Picture Tube •43 cm (17") Full square type [40.6cm (16") viewable]
• Flat face, 90˚ deflection
• 0.26 Dot pitch
• Anti-reflection coating with anti-electrostatic properties
• Medium-short persistence phosphor
Synchronization • Horizontal: 30 kHz to 96 kHz (automatic)
• Vertical: 50 Hz to 160 Hz (automatic)
Display Color • Unlimited colors
Maximum Resolution • Horizontal: 1600 dots
• Vertical: 1200 lines
Active Display • Horizontal: 306 ± 3 mm (12.05" ± 0.12")
• Vertical: 230 ± 3 mm (9.06" ± 0.12")
(Active display size is dependent upon signal timing)
Input Signal,Terminated • Video signal: Analog 0.714 Vpp positive at 75 Ω
• Separate sync: TTL Level, positive or negative
• Composite sync: TTL Level, positive or negative
• Sync-on-Green: Composite sync 0.286 Vpp negative
( Video 0.714 Vpp positive )
Maximum Pixel Clock • 205 MHz
Power Supply • AC 100-240 Volt ± 10%, 60 Hz/50 Hz ± 3 Hz
Power Consumption • 130 Watt maximum
Dimensions/Weight • Unit: 415 x 445.7 x 437.3 mm; 18.5 kg
16.3 x 17.5 x 17.2 in (W x D x H); 40.8 lbs
• Carton: 535 x 566 x 549 mm; 22.5 kg
21 x 22.3 x 21.6 in (W x D x H); 49.6 lbs
(All measurements are approximate.)
Environmental Considerations
• Operating Temperature: 32˚F to 104˚F (0˚C to 40˚C)
Humidity: 10% to 80%
• Storage Temperature: -4˚F to 113˚F (-20˚C to 45˚C)
Humidity: 5% to 95%
NOTE: Design and specifications are subject to change without prior notice.
CSH7839-E 10/8/98 10:30 AM Page 16
17
A p p e n d i x
Pin Assignments
Sync 15 Pin Side of the Signal Cable Cable Adapter
Type (Figure 1) (Figure 2)
Separate Composite Sync on Apple
Pin No. Green MAC II
1 Red Red Red GND-R
2 Green Green Green+Sync Red
3 Blue Blue Blue H/V Sync
4 GND GND GND Sense 0
5 DDC Return DDC Return DDC Return Green
6 GND-R GND-R GND-R GND-G
7 GND-G GND-G GND-G Sense 1
8 GND-B GND-B GND-B Reserved
9 Reserved Reserved Reserved Blue
10 GND-Sync/Self-Raster GND-Sync/Self-Raster GND-Sync/Self-Raster Sense 2
11 GND GND GND GND
12 DDC Data DDC Data DDC Data V-Sync
13 H-Sync H/V-Sync Not Used GND-B
14 V-Sync Not Used Not Used GND
15 DDC Clock DDC Clock DDC Clock H-Sync
CSH7839-E 10/8/98 10:30 AM Page 17
BNC Connectors
NC = No Connection
Display Modes Timing Chart
18
3
A p p e n d i x
SYNC-ON-GREEN COMPOSITE SYNC SEPARATE SYNC
R RED RED RED
G GREEN + SYNC GREEN GREEN
B BLUE BLUE BLUE
H / V NC H/V COMP. SYNC H-SYNC
V NC NC V-SYNC
SIGNALSPIN
ASSIGNMENT
Display Mode
IBM, VGA2, 720 x 400
IBM, VGA3, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1280 x 1024
VESA, 1280 x 1024
MAC 832 x 624
Horizontal
Frequency (kHz)
31.469
31.469
43.269
53.674
60.023
68.677
81.400
79.976
91.146
49.726
Vertical
Frequency (Hz)
70.087
59.940
85.008
85.061
75.029
84.997
100.000
75.025
85.024
74.551
Pixel
Clock (MHz)
28.322
25.175
36.000
56.250
78.750
94.500
113.309
135.000
157.500
57.284
Sync Polarity
(H/V)
– / +
– / –
– / –
+ / +
+ / +
+ / +
– / +
+ / +
+ / +
– / –
CSH7839-E 10/8/98 10:30 AM Page 18
FCC Information
User Instructions
The Federal Communications Commission Radio
Frequency Interference Statement includes the following
warning:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCCRules. These limits are designed to provide re a s o n -
able protection against harmful interf e rence in a re s i d e n t i a l
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interf e re n c e
to radio communications. However, there is no guarantee that
i n t e rf e rence will not occur in a particular installation.
If this equipment does cause harmful interf e r ence to radio or
television receptions, which can be determined by turning the
equipment off and on, the user is encouraged to try to corre c t
the interf e rence by one or more of the following measure s :
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
User Information
Changes or modifications not expressly approved by the
p a rty responsible for compliance could void the user’s
authority to operate the equipment.
If necessary, consult your dealer or an experienced
radio/television technician for additional suggestions. Yo u
may find the booklet called How to Identify and Resolve
Radio/TV Interf e rence Pro b l e m shelpful. This booklet was
p re p a red by the Federal Communications Commission. It
is available from the U.S. Government Printing Off i c e ,
Washington, DC 20402, Stock Number 004-000-00345-4.
Warning
User must use shielded signal interface cables to main-
tain FCC compliance for the product.
Declaration of conformity for prod-
ucts Marked with FCC Logo
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interf e rence, and (2)
this device must accept any interf e r ence received, includ-
ing interference that may cause undesired operation.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
QA Lab of Samsung America
85 West Tasman Drive
San Jose, CA 95134 USA
Tel) 408-544-5124
Fax) 408-544-5191
Provided with this monitor is a detachable power supply
cord with IEC320 style terminations. It may be suitable for
connection to any UL Listed personal computer with simi-
lar configuration. Before making the connection, make
sure the voltage rating of the computer convenience out-
let is the same as the monitor and that the ampere rating
of the computer convenience outlet is equal to or
exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable
power cord with NEMA configuration 5-15P type (parallel
blades) plug cap. For 240 Volt applications use only UL
Listed Detachable power supply cord with NEMA config-
uration 6015P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulations of ICES-003.
Cet appareil numérique de classe B respecte toutes les
exigences du Règlement ICES-003 sur les équipements
produisant des interférences au Canada.
MPR II Compliance
This monitor complies with SWEDAC (MPR II) re c o m m e n d a-
tions for reduced electric and magnetic fields.
European Notice
Products with the CE Marking comply with both the EMC
Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the
Low Voltage Directive (73/23/EEC) issued by the
Commission of the European Community.
Compliance with these directives implies conformity to
the following European Norms:
• EN55022 (CISPR 22) – Radio Frequency Interference
• EN50082-1 : 1992 – Electromagnetic Immunity
• EN60555-2 (IEC555-2) – Power Line Harmonics
• EN60555-3 (IEC555-3) – Voltage Fluctuations
• EN60950 (IEC950) – Product Safety.
CSH7839-E 10/8/98 10:30 AM Page 19
3
U.S.A. :
Samsung Electronics America (SEA)
One Samsung Place
Ledgewood, NJ 07852
Tel. : 1-800-SAMSUNG (1-800-726-7864)
Fax-on-Demand for product information :
1-800-229-2239
CANADA :
Samsung Electronics Canada Inc.
7037 Financial Drive
Mississauga, Ontario L5N 6R3
Tel. : 1-800-SAMSUNG (1-800-726-7864)
Fax. : (905) 542-1199
GERMANY :
Samsung Electronics GmbH Samsung-Haus
Am Kronberger Hang 6/65824 Schwalbach/Ts.
Tel. : 06196-66-1134
Fax. : 06196-66-1133
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Unit G, 10-16 South Street,
Rydalmere, N.S.W. 2116
P.O. BOX 368
Tel. : (02) 638 5200
ITALIA :
Samsung Electronics Italia SpA
Via C. Donat Cattin,
5-20063 Cernusco sul Naviglio (Mi)
Tel. : 167-010740
PANAMA :
Servicios Samsung (Zona Libre), S.A.
50 and 61 Streets Sta, Cecilia
Bdl. Don Camilo, Panama City
Tel. : (507) 264-0195 or 269-5571
Fax : (507) 269-5568
MEXICO :
Samsung Electronics Mexico, S.A.
DE C. V. Mina No. 200, Esq. Gavilan
Col. Guadalupe Del Moral Iztapalapa,
Mexico, D.F. C.P. 09300
Tel.: (525) 686-0800
Fax : (525) 686-5094
ESPAÑA :
Samsung Electrónics Comercial Ibérica, S.A.
Ciencies, 55-65 (Polígono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
UK :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0181) 391 0168
Fax. : (0181) 397 9949
<European Service Center & National Service>
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (01952) 292 262
Fax. : (01952) 292 033
THAILAND :
Samsung Service Center
729-729/1 JSP Tower Rachadapisek RD.,
Bangpongpang, Yannawa, Bangkok 10120
Tel : (662) 2954508-14
Fax : (662) 2954267
SOUTH AFRICA :
Samsung Electronics South Africa
Somerset Office Park 5 Libertas Road
Bryanston, South Africa
Tel : (27)-11-463-5678
Fax : (27)-11-463-5215
BRASIL :
Samsung Eletrônica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303-2ºAndar
Chácara Sto. Antônio • cep : 04719-040
São Paulo • SP
Tel. : (011) 541-8500
Fax : (011) 523-3995, 522-0726
Printed on recyclable paperCODE NO. : BN68-60???0A ( Rev. 0.1 )
CSH7839-E 10/8/98 10:30 AM Page 20