Samsung Electronics Co CSM920 User Manual MANUAL
Samsung Electronics Co Ltd MANUAL
MANUAL
Owner’s
Instructions
Color Monitor
Gemine-basic 8/20/98 11:48 AM Page i
C A U T I O N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and servicing instructions in the literature
accompanying the appliance.
Unpacking your Monitor
Please make sure the following items are included with
your computer monitor:
ii
Monitor and Stand Power Cable
This Manual
Warranty Card
Signal Cable
Gemine-basic 8/20/98 11:48 AM Page ii
Table of Contents
1
Preface: Safety Information . . . . . . . . . .2
Chapter One: Overview of Your Monitor 3
Front Panel.....................................................................................3
Rear Panel......................................................................................4
Chapter Two: Installation . . . . . . . . . . . . .5
Connecting Your Monitor to a Computer..................................5
Chapter Three: Adjusting Your Monitor . .6
Overview........................................................................................6
Brightness......................................................................................6
Contrast..........................................................................................6
Direct Access Features...............................................................7
Position....................................................................................7
Size...........................................................................................7
Pincushion/Trapezoid............................................................7
Parallel/Rotation....................................................................8
Menu Features..............................................................................8
Color temperature .................................................................8
Color Control...........................................................................9
Degauss...................................................................................9
Recall.....................................................................................10
Menu Position......................................................................10
Menu Duration.....................................................................11
Pinbalance............................................................................11
Clear Moire...........................................................................11
Language ..............................................................................12
Display Timing......................................................................12
Video Input Level.................................................................12
Sync. Input Type...................................................................13
Exit..........................................................................................13
PowerSaver.................................................................................14
Troubleshooting..........................................................................15
A p p e n d i x . . . . . . . . . . . . . . . . . . . . . . . . .1 6
Specifications..............................................................................16
Pin Assignments.........................................................................17
Display Modes Timing Chart.....................................................18
FCC Information...........................................................................19
IC Compliance Notice................................................................20
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Gemine-basic 8/20/98 11:48 AM Page 1
Preface: Safety Information
2
Please read and follow these instruc-
tions when connecting and using your
computer monitor.
1Before connecting the AC power
cord to an outlet, make sure the
voltage designation on your moni-
tor corresponds to the local elec-
trical supply.
2Never insert anything metallic into
the monitor openings. Doing so
may create the danger of electric
shock.
3To avoid electric shock, never
touch the inside of the monitor.
Only a qualified technician should
open the monitor’s case.
4Never use your monitor if the
power cord has been damaged.
Do not allow anything to rest on
the power cord, and keep the cord
away from where people could
trip over it.
5Be sure to hold the plug, not the
cord, when disconnecting the
monitor from an electric socket.
6Openings in the monitor cabinet
are provided for ventilation. To
prevent overheating, these open-
ings should not be blocked or cov-
ered. Also, avoid using the monitor
on a bed, sofa, rug, or other soft
surface. Doing so may block the
ventilation openings in the bottom
of the cabinet. If you put the moni-
tor in a bookcase or some other
enclosed space, be sure to pro-
vide adequate ventilation.
7Put your monitor in a location with
low humidity and a minimum of
dust. Avoid places like damp
basements or dusty hallways.
8Do not expose the monitor to rain
or use it near water (in kitchens,
next to swimming pools, etc.). If
the monitor accidentally gets wet,
unplug it and contact an autho-
rized dealer immediately. You can
clean the monitor with a damp
cloth when necessary, but be sure
to unplug the monitor first.
9Place the monitor on a solid sur-
face and treat it carefully. The
screen is made of glass and can
be damaged if dropped or sharply
hit.
10Locate your monitor near an easily
accessible AC outlet.
11If your monitor does not operate
normally – in particular, if there
are any unusual sounds or smells
coming from it – unplug it immedi-
ately and contact an authorized
dealer or service center.
12High temperatures can cause
problems. Don’t use your monitor
in direct sunlight, and keep it away
from heaters, stoves, fireplaces,
and other sources of heat.
13Unplug the monitor when it is
going to be left unused for an
extended period of time.
14Unplug your monitor from the AC
outlet before any service.
Gemine-basic 8/20/98 11:48 AM Page 2
3
Front Panel
1,button
Use this button to adjust the position or size.
2, button
Use this button to adjust the pincushion/trapezoid
or parallel/rotation.
3▲,▼,$, % buttons
Use these buttons to choose or adjust items in the
on-screen display.
4, MENU button
Use this button to activate the on-screen display, to
enter a selection in the on-screen display, or to exit
the on-screen displays.
5Power indicator
This light glows green during normal operation, and
blinks amber once as your adjustments are saved.
6Power button
Use this button to turn the monitor on and off.
Chapter One: Overview of Your Monitor
1 2 3 4 5
6
Gemine-basic 8/20/98 11:48 AM Page 3
Chapter One: Overview of Your Monitor
4
Rear Panel
1Power port
Connect the power cable here.
2Signal port
Connect your signal cable here.
12
Gemine-basic 8/20/98 11:48 AM Page 4
Chapter Two: Installation
5
Connecting Your Monitor
to a Computer
1Turn off your computer and unplug
its power cord.
2Connect the signal cable to the
signal port on the back of your
monitor.
3If you are using a Macintosh com-
puter, connect the other end of the
signal cable to a Macintosh
adapter. (The adapter is not includ-
ed with your monitor. Contact your
dealer for more information.) If you
are using an IBM-compatible com-
puter, skip to step 5.
4Follow the instructions included
with your adapter to set the pins
on your adapter, if necessary.
5Connect the signal cable (with the
adapter if necessary) to the video
port on the back of your computer.
This port might be directly
attached to your computer, or it
might be part of a video board,
video card, or graphics card.
6Connect the power cord for your
monitor to the power port on the
back of the monitor.
7Plug the power cords of your com-
puter and your monitor into a near-
by outlet.
8Turn on your computer and mon-
itor. If your monitor displays an
image, installation is complete.
2
67
3
5
Gemine-basic 8/20/98 11:48 AM Page 5
6
Overview
Your computer monitor allows you to easily adjust the
characteristics of the image being displayed. All of these
adjustments are made using the control buttons on the
front of the monitor. These buttons operate the on-screen
menu, which shows you the monitor’s settings and allows
you to change those settings
1Brightness
This feature will adjust the overall brightness of the
display image. Push the ▲button to increase the
brightness or the ▼ button to decrease the bright-
ness.
2Contrast
This feature will adjust the monitor’s contrast. Push
the %button to increase the contrast or the $but-
ton to decrease the contrast.
Chapter Three: Adjusting Your Monitor
1 2
Gemine-basic 8/20/98 11:48 AM Page 6
Chapter Three: Adjusting Your Monitor
7
Direct-Access Features
The features described on this page can be accessed
quickly, at the touch of one button. Once you have adjust-
ed one of these features, push the button once or twice
to turn off the display.
Position
Follow these instructions to change the position of the
monitor’s entire display.
1With the menu off, push the button. The position
display will appear.
2Use the ▲and ▼buttons to change the vertical
position of the monitor’s entire display; use the $
and %buttons to change the horizontal position of
the monitor’s entire display.
Size
Follow these instructions to change the size of the moni-
tor’s entire display.
1With the menu off, push the button twice. The
size display will appear.
2Push the ▲or ▼buttons to change the vertical size
of the monitor’s display; push the $or %buttons to
change the horizontal size of the monitor’s display.
Pincushion/Trapezoid
Adjust the pincushion setting when the sides of the dis-
play are bowed in or bowed out; adjust the trapezoid set-
ting when the top or bottom of the display is too large or
too small.
1With the menu off, push the button. The
Pincushion/Trapezoid display will appear.
2Use the $button or %button to adjust the pincush-
ion setting; use the ▲button or ▼button to adjust
the trapezoid setting.
Gemine-basic 8/20/98 11:48 AM Page 7
Chapter Three: Adjusting Your Monitor
8
Parallel/Rotation
Adjust the parallelogram setting when the display is lean-
ing left or right; adjust the rotation setting when the entire
display is tilted left or right.
1With the menu off, push the button twice.
The parallelogram/rotation display will appear.
2Use the $button or %button to adjust the parallel
setting; use the ▲button or ▼button to adjust the
rotation setting.
Menu Features
The following features can all be accessed using your
monitor’s on-screen menu system. Follow the instructions
below to adjust the features.
Once you are finished making adjustments to a feature,
push the MENU button to return to the Main Menu, then
push MENU again to turn off the menu.
Color Temperature
Follow these steps to change the color temperature set-
ting. Color temperature is a measure of the “warmth” of
the image colors.
1With the menu off, push the MENU button. Push the
$button or %button until the “Color Temperature”
screen is displayed.
2Push the button. The color temperature
adjustment screen will appear.
3Use the $button or %button to adjust the color
temperature. Use the ▲button or ▼button to
select “User color” or “Factory color.”
Gemine-basic 8/20/98 11:48 AM Page 8
Chapter Three: Adjusting Your Monitor
9
Color Control
You can change the settings of the saturation and hue of
the monitor’s display.
1With the menu off, push the MENU button. Push the
$button or %button until the “Color Control”
screen is displayed.
2Push the button. The color control adjust screen
will appear.
3Use the $button or %button to adjust the satura-
tion setting; use the ▲button or ▼button to
adjust the hue.
Degauss
The Degauss feature will remove color impurities caused
by magnetic fields. Do not use the Degauss feature more
than once within a 30-minute period.
1With the menu off, push the MENU button. Push the
$button or %button until the “Degauss” screen is
displayed.
2Push the button. The monitor will execute the
degauss function, then display the degaussing
screen.
3After a few seconds, the degauss main menu will
appear.
Note: The monitor may buzz momentarily, the image
colors may change and the image will jiggle for a
few seconds. These effects are normal.
Gemine-basic 8/20/98 11:48 AM Page 9
10
Recall
Use the recall feature to reset these monitor settings to their
original levels: position, size, pincushion, trapezoid, parallel-
ogram, pinbalance, rotation, and clear moire .
1With the menu off, push the MENU button. Push the
$button or %button until the “Recall” screen is
displayed.
2Push the button. The recall select screen will
appear.
3Push the $button to select “YES.” If you don’t want
to reset the monitor, use the %button to select
“NO.”
NOTE: If you have selected “YES,” all settings listed
above will be reset. All other settings will remain
the same.
CAUTION: This operation resets all of the data in the
user memory area for the current timing signal.
Menu Position
You can change the position where the menu appears on
your monitor.
1With the menu off, push the MENU button. Push the
$button or %button until the “Menu Position”
screen is displayed
2Push the button. The menu position adjustment
screen will appear.
3Use the ▲,▼,$or %buttons to place the menu in
the position you prefer.
Chapter Three: Adjusting Your Monitor
Gemine-basic 8/20/98 11:48 AM Page 10
11
Menu Duration
The menu will automatically turn off if no adjustments are
made for a certain time period. You can set the amount of
time the menu will wait before it turns off.
1With the menu off, push the MENU button. Push the
$button or %button until the “Menu Duration”
screen is displayed.
2Push the button. The menu duration selection
screen will appear.
3Use the $or %buttons to select 3, 7, 10, 20, or 50
seconds.
Pinbalance
Adjust the pinbalance setting when the sides of the dis-
play are bowed towards the left or right.
1With the menu off, push the MENU button. Push the
$button or %button until the “Pinbalance” screen
is displayed.
2Push the button. The pinbalance adjustment
screen will appear.
3Use the $button or %button to adjust the pinbal-
ance setting.
Clear Moire
A “moire” pattern can appear on your screen, looking like
a series of concentric circles or arcs. To eliminate this
pattern, adjust the clear moire.
1With the menu off, push the MENU button. Push the
$button or %button until the “Clear Moire”
screen is displayed.
2Push the button. The clear moire adjustment
screen will appear.
3Use the ▲,▼, $or %buttons to adjust moire is
cleared.
Chapter Three: Adjusting Your Monitor
Gemine-basic 8/20/98 11:48 AM Page 11
12
Language
Follow these steps to change the language used in the
menu. This adjustment only changes the language of the
monitor’s menu; it does not change the language of any
other software.
1With the menu off, push the MENU button. Push the
$button or %button until the “7 Languages”
screen is displayed.
2Push the button. The language selection screen
will appear.
3Use the ▲button or ▼ button to select the lan-
guage you would like to use.
Display Timing
This screen displays the settings that are available to
your monitor. This screen only displays this information;
you cannot select a new setting.
1With the menu off, push the MENU button. Push the
$button or %button until the “Display Timing”
screen is displayed.
2Push the button. The Factory Timing screen will
appear.
3Use the ▲button or ▼ button to display the user
and factory timing.
Video Input Level
This feature will select the video signal level.
1With the menu off, push the MENU button. Push the
$button or %button until the “Video Input Level”
screen is displayed.
2Push the button. The video input level select
screen will appear.
Chapter Three: Adjusting Your Monitor
Gemine-basic 8/20/98 11:48 AM Page 12
13
3Use the $or %buttons to select 0.7V or 1.0V.
NOTE: Some video cards use video singals higher
than 1.0V which causes the display to be very bright.
For those video cards should be selected 1.0V.
Sync. Input Type
Use this menu to set your monitor to the correct type of
synchronization. Select “Separate”if the computer is
sending a separate synchronization signal. Select “Sync.
On Green” if the computer expects the monitor to syn-
chronize with the green signal it sends. Refer to your
computer or video card user’s manual to determine the
correct setting.
1With the menu off, push the MENU button. Push the
$button or %button until the “Sync. Input Type”
screen is displayed.
2Push the button. The sync input type selection
screen will appear.
3Use the ▲button or ▼button to select “Separate”
or “Sync. On Green.”
Exit
Once you are finished making adjustments to a feature,
use this menu to turn off the menu.
1Once you are finished making adjustments to a fea-
ture, push the MENU button.
2Push the $button or %button until the “Exit”
screen is displayed.
3Push the MENU button to turn off the menu.
Chapter Three: Adjusting Your Monitor
Gemine-basic 8/20/98 11:48 AM Page 13
14
Chapter Three: Adjusting Your Monitor
PowerSaver
This monitor has a built-in power management system
called PowerSaver. This system saves energy by switch-
ing your monitor into a low-power mode when it has not
been used for a certain amount of time. The available
modes are “On,” “Standby,” “Suspend,” and “Off.”
This system operates with a VESA DPMS compliant
video card installed in your computer. You use a software
utility installed on your computer to set up this feature.
See the table below for details.
Power Saving function mode EPA/NUTEK
State Normal Standby mode Suspend mode / Power-off Mode /
Operation Position A1 Position A2
Horizontal Sync Active Inactive Active Inactive
Vertical Sync Active Active Inactive Inactive
Video Active Blanked Blanked Blanked
Power Green Amber Amber/Green Amber
Indicator Blinking Blinking
Power 160W (max.) 80W (nominal) Less than 15W Less than 5W
Consumption 140W (nominal)
NOTE: This monitor automatically returns to normal oper-
ation when horizontal and vertical sync return. This
occurs when you move the computer's mouse or press a
key on the keyboard.
This monitor is EPA ENERGY STAR®compliant and NUTEK
compliant when used with a computer equipped with
VESA DPMS functionality.
For energy conservation, turn your monitor OFF when it
is not needed, or when leaving it unattended for long
periods.
Gemine-basic 8/20/98 11:48 AM Page 14
15
Chapter Three: Adjusting Your Monitor
Troubleshooting
Before calling for service, check the information in this
section to see if you can remedy any problems yourself.
If you do need assistance, please call the phone number
on the warranty card, the phone number on the back
cover of this manual, or contact your dealer.
There is no screen image.
• Check to see that both the monitor and the
computer are plugged in and turned on.
Image area is lightened but No image
appears.
• Check the signal cable connection between the
computer and the monitor.
The image is too light or too dark.
• Adjust the Brightness or Contrast settings.
The image is too large or too small.
• Adjust the Size settings.
The colors are distorted with dark or
shadowed areas.
• Activate the Degauss feature.
The power indicator is amber,
amber/green, or blinking.
• The monitor is using its power management system.
Check the power management utility on your
computer.
Gemine-basic 8/20/98 11:48 AM Page 15
16
Appendix
Specifications
Picture Tube • 48.2 cm (19") Full square type [45.7cm (18.0") viewable]
• Flat face, 100˚ deflection
• 0.25 Dot pitch
• Anti-reflection coating with anti-electrostatic properties
• Medium-short persistence phosphor
Synchronization • Horizontal: 30 kHz to 96 kHz (automatic)
• Vertical: 50 Hz to 160 Hz (automatic)
Display Color • Unlimited colors
Maximum Resolution • Horizontal: 1600 dots
• Vertical: 1200 lines
Active Display • Horizontal: 350 ± 3 mm ( 13.78 ± 0.12 )( 4:3 )
328 ± 3 mm ( 12.91 ± 0.12 )( 5:4 )
• Vertical: 262.5 ± 3 mm ( 10.33 ± 0.12 )
(Active display size is dependent upon signal timing)
Input Signal,Terminated • Video signal: Analog 0.714 Vpp positive at 75 Ω
• Separate sync: TTL Level, positive or negative
• Composite sync: TTL Level, positive or negative
• Sync-on-Green: Composite sync 0.286 Vpp negative
( Video 0.714 Vpp positive )
Maximum Pixel Clock • 207 MHz
Power Supply • AC 100-240 Volt ± 10%, 60 Hz/50 Hz ± 3 Hz
Power Consumption • 160 Watt maximum
Dimensions/Weight • Unit: 460 x 407 x 465.8 mm ; 21.2 kg
18.1 x 16.0 x 18.3 inch (W x D x H); 46.7 lbs
• Carton: 580 x 510 x 566 mm; 23.5 kg
22.8 x 20.1 x 22.3 inch (W x D x H); 51.8 lbs
(All measurements are approximate.)
Environmental Considerations
• Operating Temperature: 32˚F to 104˚F (0˚C to 40˚C)
Humidity: 10% to 80%
• Storage Temperature: -4˚F to 113˚F (-20˚C to 45˚C)
Humidity: 5% to 95%
NOTE: Design and specifications are subject to change without prior notice.
Gemine-basic 8/20/98 11:48 AM Page 16
Pin Assignments
17
Appendix
Sync 15-Pin Side of the Signal Cable Cable Adapter
Type (Figure 1) (Figure 2)
Separate Composite Sync on Apple
Pin No. Green MAC II
1 Red Red Red GND-R
2 Green Green Green+Sync Red
3 Blue Blue Blue H/V Sync
4 GND GND GND Sense 0
5 DDC Return DDC Return DDC Return Green
6 GND-R GND-R GND-R GND-G
7 GND-G GND-G GND-G Sense 1
8 GND-B GND-B GND-B Reserved
9 Reserved Reserved Reserved Blue
10 GND-Sync/Self-Raster GND-Sync/Self-Raster GND-Sync/Self-Raster Sense 2
11 GND GND GND GND
12 DDC Data DDC Data DDC Data V-Sync
13 H-Sync H/V-Sync Not Used GND-B
14 V-Sync Not Used Not Used GND
15 DDC Clock DDC Clock DDC Clock H-Sync
Gemine-basic 8/20/98 11:48 AM Page 17
Appendix
18
SYNC-ON-GREEN COMPOSITE SYNC SEPARATE SYNC
R RED RED RED
G GREEN + SYNC GREEN GREEN
B BLUE BLUE BLUE
H / V NC H/V COMP. SYNC H-SYNC
V NC NC V-SYNC
SIGNALSPIN
ASSIGNMENT
BNC Connectors
NC = No Connection
Display Mode
IBM, VGA2, 720 x 400
IBM, VGA3, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1600 x 1200
MAC 1152 x 870
Horizontal
Frequency (kHz)
31.469
31.469
43.269
53.674
68.677
81.400
79.976
91.146
93.750
68.681
Vertical
Frequency (Hz)
70.087
59.940
85.008
85.061
84.997
100.000
75.025
85.024
75.000
75.062
Pixel
Clock (MHz)
28.322
25.175
36.000
56.250
94.500
113.309
135.000
157.500
202.500
100.000
Sync Polarity
(H/V)
– / +
– / –
– / –
+ / +
+ / +
– / +
+ / +
+ / +
+ / +
– / –
Display Modes Timing Chart
Gemine-basic 8/20/98 11:48 AM Page 18
Chapter Three: Adjusting Your Monitor
19
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference
Statement includes the following warning:
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
receptions, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsi-
ble for compliance could void the user’s authority to operate the equip-
ment.
If necessary, consult your dealer or an experienced radio/television
technician for additional suggestions. You may find the booklet called
How to Identify and Resolve Radio/TV Interference Problems helpful.
This booklet was prepared by the Federal Communications Commission.
It is available from the U.S. Government Printing Office, Washington, DC
20402, Stock Number 004-000-00345-4.
Gemine-basic 8/20/98 11:48 AM Page 19
20
Warning
User must use shielded signal interface cables to maintain FCC compli-
ance for the product.
Declaration of conformity for products
Marked with FCC Logo
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The party responsible for product compliance :
SAMSUNG ELECTRONICS CO., LTD
QA Lab of Samsung America
85 West Tasman Drive
San Jose, CA 95134 USA
Tel) 408-544-5124
Fax) 408-544-5191
Provided with this monitor is a detachable power supply cord with
IEC320 style terminations. It may be suitable for connection to any UL
Listed personal computer with similar configuration. Before making the
connection, make sure the voltage rating of the computer convenience
outlet is the same as the monitor and that the ampere rating of the com-
puter convenience outlet is equal to or exceeds the monitor voltage rat-
ing.
For 120 Volt applications, use only UL Listed Detachable Power cord with
NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt
applications use only UL Listed Detachable power supply cord with
NEMA configuration 6015P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations of ICES-003.
Appendix
Gemine-basic 8/20/98 11:48 AM Page 20
21
▲ ▼ buttons . . . . . . . . . . . . . . . . . . . . . . . . . .3
$ % buttons . . . . . . . . . . . . . . . . . . . . . . . . . .3
A
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
B
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
C
Clear moire . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Color control . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Color temperature . . . . . . . . . . . . . . . . . . . . . .8
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
D
Degauss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Display Modes Timing Chart . . . . . . . . . . . .17
Display Timing . . . . . . . . . . . . . . . . . . . . . . . .12
Duration, menu . . . . . . . . . . . . . . . . . . . . . . .11
E
EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
F
FCC Information . . . . . . . . . . . . . . . . . . . . . . .18
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
I
IC Compliance Notice . . . . . . . . . . . . . . . . . .20
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
L
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
M
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Menu duration . . . . . . . . . . . . . . . . . . . . . . . .11
Menu position . . . . . . . . . . . . . . . . . . . . . . . .10
P
Parallelogram . . . . . . . . . . . . . . . . . . . . . . . . . .8
Pin assignments . . . . . . . . . . . . . . . . . . . . . .17
Pinbalance . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Pincushion . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Position, menu . . . . . . . . . . . . . . . . . . . . . . . .10
Power button . . . . . . . . . . . . . . . . . . . . . . . . . .3
Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
Power indicator . . . . . . . . . . . . . . . . . . . . . . . .3
Power port . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PowerSaver . . . . . . . . . . . . . . . . . . . . . . . . . .14
R
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
S
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Signal cable . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
Signal port . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Specifications . . . . . . . . . . . . . . . . . . . . . . . .16
Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
Sync. Input Type . . . . . . . . . . . . . . . . . . . . . .13
T
Table of contents . . . . . . . . . . . . . . . . . . . . . . .1
Trapezoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .15
V
Video Input Level . . . . . . . . . . . . . . . . . . . . . .12
W
Warranty Card . . . . . . . . . . . . . . . . . . . . . . . . .ii
Index
Gemine-basic 8/20/98 11:48 AM Page 21