Samsung Electronics Co DELL5002 2.4 GHz WLAN Module User Manual
Samsung Electronics Co Ltd 2.4 GHz WLAN Module Users Manual
User Manual
Dell 5002 Datasheet
REV 0.1
Samsung Electronics
Summary
T
his datasheet presents the general performance and specifications of Dell 5002
IEEE 802.11b/g WLAN CARD using SWL-2900U.
ML-NWA30L
Figure 1-1 Dell 5002
Dell 5002 is the low power USB interface card for 802.11b/g wireless LAN aimed at
embedded application. Dell 5002 is the USB interface card that adopts a single-chip wireless
LAN MAC(medium-access controller) spread-spectrum baseband processor and 2.4GHz RF
radio.
Dell 5002 supports IEEE 802.11b and 802.11g standards. Data rate up to 54MHz can be
provided in 802.11g mode of operation.
The main IC of Dell 5002 includes an 80MHz ARM7 core, 384KB of on-chip SRAM, and 80KB
of on-chip ROM. Dell 5002 is able to host the entire WLAN driver and TCP/IP stack on-chip.
This minimizes development time, cost, and burden on the host processor resources making
Dell 5002 an ideal WLAN solution for emdedded application.
Dell 5002 provides crucial power management functionality and requires only a single 5.0V
supply voltage.
Figure 1-2 Dell 5002 Block Diagram
1.3 Block Diagram
Figure 2-1 Dell 5002 Mechanical Dimension
Figure 2-2 Dell 5002 Picture
W x L x H = 51mm x 108mm x 18mm
pin #1 pin #20
pin #21 pin #40
Table 2-1 CN1 PIN Description
Figure 2-3 Dell 5002 CN1 Connector PIN Assignment
Host Interface : Molex 5084616-1, 40pin, Straight, SMT
* SIZE : 6.5 x 21.5 x 11.5 mm
+35
In the case of measurement with Case, Antenna specificaiton is like below.
0.1 2008.02.18 First released
FCC Compliance
Ì FCC Statement
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Ì Caution
Any changes or modifications NOT
explicitly APPROVED by Samsung
Electronics Co., Ltd. could cause the
DELL5002 module to cease to comply with
FCC rules part 15, and thus void the user's
authority to operate the equipment.
Ì RF-exposure statement
These modular transmitters, Dell5002,
comply with FCC radiation exposure limits
set forth for an uncontrolled environment.
The Dell5002 should be installed and
operated with minimum distance 20cm
between the antenna and the body of the
user or nearby persons.
The OEM integrator has to be aware not to
provide information to the end user
regarding how to install or remove this RF
module in the users manual of the end
product which integrate this module.
This device is intended only for OEM
integrators under the following conditions:
1) The antenna must be installed such that 20
cm is maintained between the antenna and
users, and 2) The transmitter module may not
be co-located with any other transmitter or
antenna.
As long as the 2 conditions above are met,
further transmitter testing will not be
required. However, the OEM integrator is
still responsible for testing their end
product for any additional compliance
requirements required with this module
installed (for example, digital device
emissions, PC peripheral requirements,
etc.).
IMPORTANT NOTE: In the event that
these conditions cannot be met (for
example certain laptop configurations or
co-location with another transmitter), then
the FCC authorization is no longer
considered valid and the FCC ID cannot
be used on the final product. In these
circumstances, the OEM integrator will be
responsible for re-evaluating the end
product (including the transmitter) and
obtaining a separate FCC authorization.
Ì Antenna
These modular transmitters are for OEM
integrations only. The end-user product will
be installed in such a manner that only the
authorized antennas are used.
Ì Label and manual requirements for the End
Product
For an end product using the Dell5002
there must be a label containing, at least,
the following information:
FCC ID for model Dell5002
The label must be affixed on an exterior
surface of the end product such that it will
be visible upon inspection in compliance
with the modular approval guidelines
developed by the FCC.
This device contains
FCC ID: A3LDELL5002
Where the Dell5002 will be installed in
final products larger than 8cm x 10cm
following statements has to be placed
ONTO the device.
"This device complies with Part 15 of the FCC
Rules.
Operation is subject to the following two
conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation."
In case where the final product will be
installed in locations where the end-
consumer is not able to see the FCC ID
and/or this statement, the FCC ID and the
statement shall also be included in the
end-product manual.
The users manual for end users must
include the following information in a
prominent location "IMPORTANT NOTE: To
comply with FCC RF exposure compliance
requirements, the antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from all
persons and must not be co-located or
operating in conjunction with any other
antenna or transmitter."
EU Compliance
Ì Regulatory compliance of the Dell5002
The Dell5002 are made for OEM
integrations only. The European
regulations applying to the Dell5002 is
the R&TTE Directive 1999/5/EC.
Dell5002 meets the following
requirements of the R&TTE Directive.
R&TTE
Directive
article
Test category Harmonized
standard
Article 3.1(a) Protection of
health and safety
EN 60950-1,
EN 50385
Article 3.1(b) EMC EN 301 489-1/-17
Article 3.2 Effective use of the
spectrum
EN 300 328
The conformity assessment for the
Dell5002 were completed in accordance
with the R&TTE Directive Annex IV
procedures, and the EC Declaration of
Conformity is attached to this manual.
Ì Cautions regarding regulatory compliance
when integrating the Dell5002
The person integrating the Dell5002
becomes the manufacturer of the final
product and is therefore responsible for
demonstrating compliance of the product
with the essential requirements of the
R&TTE Directive.
In all cases assessment of the final
product must be made against the
Essential requirements of the R&TTE
Directive Article 3.1(a) and (b), safety and
EMC respectively, and any relevant Article
3.3 requirements
This device is intended only for OEM
integrators under the following conditions:
1. This appliance and its antenna must not
be co-located or operating in conjunction
with any other antenna or transmitter.
2. A minimum separation distance of 20
cm must be maintained between the
antenna and the person for this appliance
to satisfy the RF exposure requirements of
the Council recommendation 1999/519/EC
of 12 July 1999.
As long as the 2 conditions above are met,
no further evaluation under Article 3.2 of
the R&TTE Directive and do not require
further involvement of an R&TTE Directive
Notified Body for the final product. In all
other cases, or if the manufacturer of the
final product is in doubt then the
equipment integrating the radio module
must be assessed against Article 3.2 of
the R&TTE Directive.
Please note that this product, Dell5002,
uses radio frequency bands not
harmonized throughout the Community.
This product is classified as Class 2 radio
equipment for which some Member States
apply restrictions on placing on the market
and in use. Any parties putting Class 2
radio equipment on the market must notify
the relevant national spectrum
management authority of their intention,
and the radio equipment must be given a
Class Identifier (alert symbol).
Ì Antenna
This product, Dell5002, is for OEM
integrations only. The end-user product will
be installed in such a manner that only the
authorized antennas are used.
Ì Enclosure
This product, Dell5002, is made for
integrating in another final product. For
this reason, there are some parts of the
final product on which the Dell5002
depends for regulatory compliance
regarding EMC and safety. The Dell5002
is mounted on the circuit board of the final
product, and must be contained inside the
case of the final product. Integrated the
Dell5002 in the final product so that its
surfaces are not in contact with the outside.
Ì Documentation
In the documentation for the conformity
assessment of the final product, state
clearly that the Dell5002 is integrated in
the system.
Ì Conformity Assessment of the Products
integrating the Dell5002
The following is a supplementary
explanation of conformity assessments for
final products integrating the radio
modules such as the Dell5002, that have
passed conformity assessments in
accordance with the R&TTE Directive.
The procedures for conformity assessment
in accordance with the R&TTE Directive
are the responsibility of the manufacturer
of the final product. With final products
integrating radio modules, the person who
integrates the module in the system
becomes the manufacturer of the final
product, and it is their responsibility to
certify that the requirements of the R&TTE
Directive and met.
Ì Exemption from conformity assessment
However, if radio modules that meet the
requirements of the R&TTE Directive and
that have passed the conformity
assessment are integrated in a final
product that follows the cautions
concerning integrating radio modules, they
are exempted from the conformity
assessment for R&TTE Directive Article
3.2 (efficient use of the radio spectrum).
For details, refer to the following Guidance
and ETSI Technical Report from the
R&TTE Compliance Association, and
check whether your case applies.
Organization R&TTE Compliance
Association
Document No.
TGN 01 Rev 3
Document title Technical Guidance Note on
Requirement for a Final Product that
Integrates an R&TTE Directive Assessed
Module
URL You can download the guidance from the
download area of R&TTE Compliance
association. http://www.rtteca.com
Organization ETSI (Technical
report)
Document No. ETSI
TR 102 070-2
Document title Electromagnetic compatibility and Radio
spectrum Matters (ERM); Guide to the
application of harmonized standards to
multi-radio and combined radio and non-
radio equipment; Part 2: Effective use of
radio frequency spectrum
URL You can download the guidance from
the ETSI web site by entering TR102
070-2 in the search engine. Before
downloading, you will be requested to
register.
http://www.rtteca.com
Ì Conformity assessment procedures for final
products exempted from R&TTE Directive
Article 3.2
In every case, the manufacturer of a final
product must follow the procedures for
conformity assessment of the final product
with the requirements of R&TTE Directive
Article 3.1(a) and (b), for safety and EMC.
The conformity assessment for Article 3.2
is carried out in accordance with the
following:
1) Attach the EN 300 328 test report of the
assessed radio module and the EC
Declaration of Conformity to the conformity
assessment of the final product (The
Declaration of Conformity is attached to
the manual).
2) Specify on the conformity assessment
of the end product that the assessed radio
module was integrated in the system
without any changes, in accordance with
the installation directions of the
manufacturer.
Ì Notification of the final product
Please note that this product, Dell5002,
uses radio frequency bands not
harmonized throughout the Community.
The notification required by R&TTE
Directive Article 6(4) is necessary. It is the
responsibility of the manufacturer of the
final product to notify the relevant national
spectrum management authority of the
intention to place the final product on the
market.
Ì CE marking
It is necessary to attach the CE mark to
the final product to indicate that it
conforms with all the directives that apply
to the final product. It must be given a
Class Identifier (alert symbol) in addition to
the CE mark.
Ì Exemption clause
Samsung Electronics Co., Ltd. does not
guarantee the accuracy of the information
above. In case of doubt or uncertainty, we
recommend that you check with the
authorities or official certification
organizations of the relevant countries.
EC Declaration of Conformity
We, Samsung Electronics Co., Ltd.
of Samsung Electronics Co., Ltd.
#259, Gongdan-Dong, Gumi-City,
Gyeongsangbuk-Do, 730-030 Korea
of Samsung Electronics(Shandong)
Digital Printing Co., Ltd.
264209, Samsung Road, Weihai Hi-Tech
IDZ, Shandong Province, China
declare under our sole responsibility that the
product
WLAN Module
model " Dell5002 "
to which this declaration relates is in conformity
with
R&TTE Directive 1999/5/EC
By application of the following standards
Article
3.1(a)
Health EN 50385:2002
Article
3.1(a)
Safety EN 60950-1:2001
Article
3.1(b)
EMC EN 301 489-1
V1.7.1(2006-10),
EN 301 489-17
V1.2.1(2002-08)
Article 3.2 Radio EN 300 328
V1.7.1 (2006-10)
Notified
Body UL Apex Co., Ltd.
4383-326, Asama-cho, Ise-shi,
Mie 516-0021, JAPAN
EU Identification Number: 1731
Documentary evidence to demonstrate
conformity
Description
Report or
Certificate
No.
Issue
Date Issued by
Health
Declaration of
Conformity issued by
Samsung Electronics
Co., Ltd.
Safety SK Tech Co., LTD.
EMC SK Tech Co., LTD.
Radio SK Tech Co., LTD.
Manufacturer
Samsung Electronics Co., Ltd.
#259, Gongdan-Dong, Gumi-City
Gyungbuk, Korea 730-030
(Sang youp Hyoun) / 17th ,January ,2008