Samsung Electronics Co DVDVR320A DVD Recorder/ Video Cassette Recorder User Manual 00588A 00 VR320 1 XAA eng

Download:
Mirror Download [FCC.gov]
Document ID	563430
Application ID	BqkxlBHFJ3B2nkxZnkPC1g==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	231.5kB (2893715 bits)
Date Submitted	2005-07-19 00:00:00
Date Available	2005-07-19 00:00:00
Creation Date	2005-07-19 17:13:54
Producing Software	Acrobat Distiller 5.00 for Macintosh
Document Lastmod	2005-07-19 17:14:54
Document Title	00588A(00)-VR320-1/XAA-eng
Document Creator	QuarkXPress.: AdobePS 8.8.0 (301)
Document Author:	sul

00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 1
Instruction Manual
DVD-VR320
www.samsung.com
AK68-00588A-02
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 2
Getting Started
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
Do not install this equipment in a confined space such
as a bookcase or similar unit.
WARNING : To prevent damage which may result in fire or
electric shock hazard, do not expose this appliance to rain or moisture.
CAUTION : This DVD Recorder & VCR USES AN INVISIBLE LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE IF
DIRECTED.
BE SURE TO OPERATE RECORDER CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTIONS
Caution: To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques, introduíre la
lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu au
fond.
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference
with electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
2 - English
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

 This unit can be used only where the power
supply is AC 120V, 60Hz. It cannot be used elseNote
where.

 This DVD Recorder & VCR is designed and
manufactured to respond to the Region
Management Information.
If the Region number of a DVD disc does not correspond to the Region number of this , the DVD
Recorder & VCR cannot play the disc.

 This device is protected by U.S. Patent
Nos.4,631,603;4,577,216;4,819,098;4,907,093; and
6,516,132. This product incorporates copyright protection technology that is protected by U.S. patents
and other intellectual property rights. Use of this
copyright protection technology must be
authorized by Macrovision,and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse
engineering or disassembly is prohibited.

 This product is covered by one or more of the
following U.S. patents:
5,034,830 5,060,200 5,457,669 5,561,649
5,691,858 5,705,762 5,987,417 6,043,912
6,222,983 6,272,096 6,377,524 6,377,531
6,385,587 6,389,569 6,389,570 6,408,408
6,466,532 6,473,736 6,477,501 6,480,829
6,556,520 6,556,521 6,556,522 6,594,208
6,674,697 6,674,957 6,721,493 6,728,474
6,741,535 09/610381 09/610695
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 3
Precaution
• Exterior interference such as lightning and static electricity can affect normal operation of this recorder. If
this occurs, turn the DVD Recorder & VCR off and on
again with the POWER button, or disconnect and then
reconnect the AC power cord to the AC power outlet.
The recorder will operate normally.
use.
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. if the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Handling Cautions
• Before connecting other components to this
recorder, be sure to turn them all off.
• Do not move the recorder while a disc is being
played, or the disc may be scratched or broken,
and the recorder’s internal parts may be damaged.
• Do not put a flower vase filled with water or any
small metal objects on the recorder.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the
disc tray.
• Disconnect the AC power cord from the AC outlet
when you don’t intend to use the recorder for long
periods of time.
• Clean the disc by wiping in a straight line from the
inside to the outside of the disc.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power
cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for
cleaning.
• Wipe the cabinet with a soft cloth.
Disc Handling
• Use discs with regular shapes.
If an irregular disc (a disc with
a special shape) is used, this
DVD Recorder & VCR may be
damaged.
Holding discs
• Avoid touching the surface of a disc
where recording is performed.
DVD-RAM, DVD-RW and DVD-R
• Clean with an optional DVD-RAM/PD
disc cleaner.
Do not use cleaners or cloths for CDs
to clean DVD-RAM/ DVD-RW/DVD-R
discs.
DVD-Video, CD
• Wipe off dirt or contamination on the disc with a soft
cloth.
Cautions on handling discs
• Do not write on the printed side with a ball-point pen
or pencil.
• Do not use record cleaning sprays or antistatic. Also,
do not use volatile chemicals, such as benzene or
thinner.
English - 3
Getting Started
• Be sure to remove the disc and turn off the recorder after
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 4
Getting Started
• Do not apply labels or stickers to discs. (Do not use
discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available
on the market.
• Do not load warped or cracked discs.
Disc Storage
Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
• If you move your DVD Recorder & VCR suddenly from
a cold place to a warm place, condensation may generate on the operating parts and lens and cause
abnormal disc playback. If this occurs, remove the
disc and wait for one to two hours with the power on
before attempting playback.
Disc Specifications
DVD-Video
• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture compression and Dolby 3D surround, allowing you to
enjoy vivid and clear theater quality images in the
comfort of your own home.
• When switching from the first layer to the second layer
of a double-layered DVD Video disc, there may be
momentary distortion in the image and sound.
This is not a malfunction of the unit.
• Once a DVD-RW/-R recorded in Video Mode is finalized, it becomes DVD-Video.
Audio CD
• An audio disc on which 44.1kHz PCM Audio is recorded.
• Plays CD-DA format audio CD-R and CD-RW discs.
This unit may not be able to play some CD-R or CDRW discs due to the condition of the recording.
CD-R/RW
MP3 CD-R/RW
• Only CD-R discs with MP3 files recorded with
•
•
•
•
ISO9660 or JOLIET format can be played back
Only MP3 files with the "mp3" or "MP3" extension can
be used.
For MP3 files recorded with a VBR(Variable Bit
Rates), from 32 Kbps to 320 Kbps, the sound may cut
in out.
Playable bitrate range is from 56Kbps to 320Kbps.
The unit can handle a maximum of 1000 files and folders.
4 - English
JPEG CD-R/RW
• Only JPEG files with the ".jpg", ".JPG" extension can be
used.
• The unit can handle a maximum of 1000 files and folders.
• Maximum size of progressive JPEG is 3M pixels.
• MOTION JPEG is not supported.
Using CD-R/RW
• Use a 700MB(80 minutes) CD-R/RW disc.
If possible, do not use a 800MB(90 minutes) or above disc,
as the disc may not play back.
• If the CD-R/RW disc was not recorded as a closed session,
you may experience a delay in the early play-back time, and
all recorded files may not play.
• Some CD-R/RW discs may not be playable with this unit,
depending on the device which was used to burn them.
For contents recorded on CD-R/RW media from CDs for
your personal use, playability may vary depending on contents and discs.
DVD-R Disc Playback and Recording
• Once a DVD-R recorded in Video Mode is finalized, it
becomes DVD-Video.
• You can record onto the available space on the disc and
perform editing functions such as giving titles to discs and
programs and erasing programs before finalizing.
• When programming is erased from a DVD-R, that space
does not become available. Once an area on a DVD-R is
recorded on, that area is no longer available for recording,
whether the recording is erased or not.
• It takes about 30 seconds for the unit to complete recording
management information after recording finishes.
• This product optimizes the DVD-R for each recording.
Optimizing is carried out when you start recording after
inserting the disc or turning on the unit. Recording onto the
disc may become impossible if optimizing is carried out too
many times.
• Playback may be impossible in some cases due to the condition of recording.
• This unit can play back DVD-R discs recorded and finalized
with a Samsung DVD video recorder. It may not be able to
play some DVD-R discs depending on the disc and the condition of the recording.
DVD-RW Disc Playback and Recording
• Recording and playback can be performed on DVD-RW
discs in both Video and VR Modes.
• Once a DVD-RW recorded in VR Mode is finalized, you cannot perform additional recording.
• Once a DVD-RW recorded in Video Mode is finalized, it
becomes DVD-Video.
• In both modes, playback can be performed before and after
finalization, but additional recording, deleting and editing can
not be performed after finalization.
• If you want to record the disc in VR Mode and then record in
V Mode, be sure to execute Format. Be careful when executing Format because all the recorded data may be lost.
• A DVD-RW blank disc is initialized to VR Mode when first initialized.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 5
• DVD-RW (VR mode)
• DVD-RW (Video mode)
- This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by an
existing DVD player once it has been finalized.
- If a disc that has been recorded in Video mode by a different manufacturer's recorder but has not been finalized
it cannot be played or additionally be recorded by this
recorder.
DVD-RAM Disc Playback and Recording
• For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.
• Ensure that the recording mode is set to VR mode.
Otherwise, this product will not be able to play the
recording.
• You cannot play a DVD-RAM in most DVD players due
to compatibility issues.
• Only DVD-RAM standard Version 2.0 discs can be
played in this unit.
• DVD-RAM recorded on this unit may not work with other
DVD Players. To determine compatibility with these DVDRAM discs, refer to the user’s manual for the player.
COPY PROTECTION
Do not use the following discs!
• LD, CD-G, CD-I, CD-ROM, DVD-ROM, VCD, DVD+R
and DVD+RW discs should not be used in this product.
[Note]
Disc types that can be played : CD/CD-R/CD-RW/MP3/
JPEG/DVD-Video/DVD-RAM/ DVD-RW/DVD-R. However,
if your DVD-RW disc was recorded with another device, it
can be played only if it was recorded and finalized in video
mode.
• Some commercial discs and DVD discs purchased outside your region may not be playable with this product.
When these discs are played, either “No disc.” or
“Please check the regional code.” will be displayed.
• If your DVD-RW disc is an illegal copy or is not in DVD
video format, it may also not be playable.
❇ We recommend using one of the discs in the table
as they have been confirmed to be compatible with
this unit. Other discs may not perform correctly.
Media
DVD-R
• Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
Recorder & VCR directly to your TV, not to a VCR.
Connecting to a VCR results in a distorted picture
from copy-protected DVD discs.
• This product incorporates copyright protection technology that is protected by methods claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
Protection
• Program-protected: See page 66 “Locking a Title”
• Disc-protected: See page 78 “Disc Protection”
❋ DVD-RAM/DVD-RW/DVD-R discs that are incompatible
with the DVD-VIDEO format cannot be played with this
product.
❋ For more information on DVD recording compatibility,
consult your DVD-RAM/DVD-RW/DVD-R manufacturer.
❋ Use of poor quality DVD-RAM/DVD-RW/DVD-R discs
may cause following unexpected problems including,
without limitation, recording failure, loss of recorded or
edited materials or damage to the recorder.
DVD-RW
DVD-RAM
Disc
DVD-RAM
DVD-RW
DVD-R
Brand
TDK
Beall
Sony
That’s
Mitsubishi
Maxell
Panasonic
TDK
Maxell
Optodisc
JVC
Mitsubishi
Radius
Verbatim
Maxell
Maxell
Fujifilm
Panasonic
TDK
Panasonic Gold
Panasonic
Speed
4x
4x
4x
4x
4x
4x
4x
2x
2x
2x
2x
2x
2x
2x
3x
2x
3x
2x
2x
3x
3x
No. of maximum recordings by disc type
100,000
1,000
• We take no responsibility and offer no compensation for
any recording failure, loss of recorded or edited material
and/or damage to the recorder arising from usage of
non-recommended discs.
English - 5
Getting Started
- This is a format that is used for recording data on a DVDRAM or DVD-RW disc. You can record multiple titles,
edit, delete, partial delete, create a playlist, etc.
- A disc that is recorded in this mode may not be played
by existing DVD players.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 6
Contents
Step 4 : Connecting the Audio cable . . . . . . . . . . .18
Method 1 : Connecting to your TV . . . . . . . . . . . . . . .18
Method 2 : Connecting to a stereo amplifier with
Getting Started
analog input jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Method 3: Connecting to an AV amplifier with a
Getting Started
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3
Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Before Reading the User’s Manual . . . . . . . . . . . . .8
How to use the DVD Recorder & VCR . . . . . . . . . . .9
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .13
Connecting & Setting Up
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Step 1 : Unpacking . . . . . . . . . . . . . . . . . . . . . . . . .15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 2 : Connecting the Antenna cable . . . . . . . . . .15
Method 1 : Antenna + DVD Recorder & VCR +
TV : No Cable box . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Method 2 : Antenna +Cable box +
DVD Recorder & VCR + TV : Cable box with many
scrambled channels . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Method 3 : Antenna + DVD Recorder & VCR +
digital input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 5 : Connecting external devices . . . . . . . . . . .19
Method 1 : Connecting a VCR, Set-Top Box(STB)
or DVD player to the AV IN 1 jacks . . . . . . . . . . . . . . .19
Method 2 : Connecting a Camcorder to the
AV IN 2 jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Method 3 : Connecting a Camcorder to the
DV IN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Step 6 : Connecting the Power Cord . . . . . . . . . . .20
Step 7 : Preparing the Remote Control . . . . . . . . .20
Setting the Remote Control . . . . . . . . . . . . . . . . . . . . .21
System Setup
On-Screen Menu Navigation . . . . . . . . . . . . . . . . .22
Auto Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Manual Clock Set . . . . . . . . . . . . . . . . . . . . . . . . .24
Channel Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Auto Channel Memory . . . . . . . . . . . . . . . . . . . . . .25
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . .26
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . .26
Setting Up the Language Options . . . . . . . . . . . . .27
Setting Up the Audio Options . . . . . . . . . . . . . . . .28
Setting Up the Display (Video) Options . . . . . . . . .29
Setting Up the Parental Control . . . . . . . . . . . . . . .30
VCR Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Video Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Front Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
DVD EP Mode Time . . . . . . . . . . . . . . . . . . . . . . .33
Automatic Chapter Creator . . . . . . . . . . . . . . . . . .34
Playback
Cable box +TV : Cable box with a few
scrambled channels . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Step 3 : Connecting the Video cable . . . . . . . . . . . .16
Method 1 : Connecting to a Video input jack . . . . . . . . .16
Method 2 : Connecting to an S-video input jack . . . . . . .17
Method 3 : Connecting to Component video input
jacks(Y,PB,PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
6 - English
 DVD Playback
Before Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Using the Disc Menu and Title Menu . . . . . . . . . . .37
Using the Search & Skip Functions . . . . . . . . . . . .37
Slow Motion Play / Step Motion Play . . . . . . . . . . .38
About ANYKEY . . . . . . . . . . . . . . . . . . . . . . . . . . .38
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 7
 VCR Playback
Playing the VCR . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Special VCR Playback Features . . . . . . . . . . . . . .49
S-VHS Playback . . . . . . . . . . . . . . . . . . . . . . . . . .49
Variable Search System . . . . . . . . . . . . . . . . . . . . .50
Recording
 DVD Recording
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . .51
Recordable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Recording Formats . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Recording Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Unrecordable video . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Recording the current channel you are watching .53
Recording From External Devices . . . . . . . . . . . . .54
Recording through a DV Input jack . . . . . . . . . . . .54
Making a One Touch Recording(OTR) . . . . . . . . . .55
Making a Timer Recording . . . . . . . . . . . . . . . . . . .55
Editing the Scheduled Record List . . . . . . . . . . . . .57
Deleting the Scheduled Record List . . . . . . . . . . . .58
Editing
Playing the Title List . . . . . . . . . . . . . . . . . . . . . . . .63
Basic Editing (Title List) . . . . . . . . . . . . . . . . . . . . .65
Renaming(Labeling) a Title . . . . . . . . . . . . . . . . . . . . .65
Locking(Protecting) a Title . . . . . . . . . . . . . . . . . . . . . .66
Deleting a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Deleting a Section of a Title . . . . . . . . . . . . . . . . . . . .67
Advanced Editing (Playlist) . . . . . . . . . . . . . . . . . . .69
Creating a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Playing Titles in the Playlist . . . . . . . . . . . . . . . . . . . . .70
Renaming a Playlist Title . . . . . . . . . . . . . . . . . . . . . . .71
Editing a Scene for the Playlist . . . . . . . . . . . . . . . . . .72
Copying a Playlist Title to the VCR . . . . . . . . . . . . . . .75
Deleting a Playlist Title from the Playlist . . . . . . . . . . .76
Disc Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Editing the Disc Name . . . . . . . . . . . . . . . . . . . . . .77
Disc Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Formatting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Finalizing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Delete All Title Lists . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Unfinalizing a disc (V/VR mode) . . . . . . . . . . . . . . . . .81
Reference
Troubleshooting
(DVD-VIDEO/DVD-RAM/DVD-RW/DVD-R) . . . . .83
Troubleshooting(DVD) . . . . . . . . . . . . . . . . . . . . . .84
Troubleshooting(VCR) . . . . . . . . . . . . . . . . . . . . . .85
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
 VCR Recording
Basic VCR Recording . . . . . . . . . . . . . . . . . . . . . .59
Check Remaining Time . . . . . . . . . . . . . . . . . . . . .59
Special Recording Features . . . . . . . . . . . . . . . . .60
Copy to DVD or VCR . . . . . . . . . . . . . . . . . . . . . . .61
English - 7
Getting Started
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Selecting the Subtitle & Audio Language . . . . . . . .41
Changing the Camera Angle . . . . . . . . . . . . . . . . .42
Zooming-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Using the Bookmarks . . . . . . . . . . . . . . . . . . . . . .43
Using the Markers . . . . . . . . . . . . . . . . . . . . . . . . .44
Playing back an Audio CD (CD-DA) . . . . . . . . . . . .45
Playing back an MP3 CD . . . . . . . . . . . . . . . . . . . .46
Play Option Mode . . . . . . . . . . . . . . . . . . . . . . . . .47
To Program Tracks . . . . . . . . . . . . . . . . . . . . . . . . .47
Playing a picture CD . . . . . . . . . . . . . . . . . . . . . . .48
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 8
Getting Started
General Features
The DVD-VR320 allows you to record and play high
quality digital video on DVD-RAM/DVD-RW/DVD-R
discs. You can record and edit digital video on
DVD-RAM/ DVD-RW/DVD-R discs as if they were VCR
tapes.
High quality digital audio and video recording and
playback
Record up to about 16-hour images with a double side 9.4
GB DVD-RAM disc, and up to about 8-hour images with a
4.7 GB DVD-RAM/DVD-RW/DVD-R disc, depending on the
recording mode.
Creating DVD video titles using DVD-RW/DVD-R discs
With the DVD-VR320, you can create your own DVD video
titles on 4.7 GB DVD-RW/DVD-R discs.
A Variety of Recording Options
Select an appropriate recording mode between XP, SP, LP
and EP to meet your recording needs. (See page 52.)
• XP mode - High quality, about 1 hour
• SP mode - Standard quality, about 2 hours
• LP mode - Low quality, about 4 hours
• EP mode - Lower quality, about 6 or 8 hours
Before Reading the
User’s Manual
Make sure to check the following terms before reading
the user’s manual.
Icons that will be used in manual
Icon
Term
Definition
DVD
This involves a function available
in DVD or DVD-R/DVD-RW
discs that have been recorded
and finalized in Video Mode.
RAM
This involves a function available
in DVD-RAM.
RW
This involves a function available
in DVD-RW.
This involves a function available
in DVD-R.
CD
This involves a function available
in a data CD (CD-R or CD-RW).
JPEG
This involves a function available
in a data picture CD (CD-R or
CD-RW).
MP3
This involves a function available
in a data CD (CD-R or CD-RW
on which MP3 is recorded).
Copying digital camcorder content using DV input jack
Record digital camcorder images onto DVD-RAM/
DVD-RW/DVD-R discs or video tape using the DV input
jack (IEEE 1394-4pin). (See page 19.)
High quality progressive scan
Progressive scanning provides high resolution and flicker
free video. The 10-bit 54-MHz DAC, 2D Y/C Separating circuitry and Time Base Corrector processor technology provide you with the highest image playback and recording
quality. (See page 17.)
Component progressive scan output video is available in
both DVD and VCR modes.
Caution
This involves a case where a
function does not operate or
settings may be cancelled.
NOTE
This involves tips or instructions
on the page that help each
function operate.
One-Touch A function that can be operated
button
by using only one button.
ANYKEY
button
A function that can be operated
by using ANYKEY button.
About the use of this user’s manual
A variety of functions with easy-to-use user
interface
Integrated menu system and messaging functionality allow
you to perform the desired operations easily and conveniently. With a DVD-RAM/DVD-RW(VR mode) disc, you
can edit recorded images, create playlist, and edit video in
specific sequence according to your needs.
1) Be sure to be familiar with Safety Instructions before
using this product. (See pages 2~5)
2) If a problem occurs, check the Troubleshooting.
(See pages 83~85)
Copyright
©2005 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.
8 - English
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 9
How to use the DVD
Recorder & VCR
Select the disc type
Recording
There are two different recording methods: Direct
Recording and Timer Recording. Timer recording is
classified as a Date : Once, Daily or Weekly.
Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and
EP (extended mode).
This unit can record on the following types of discs.
If you want to repeatedly record on the same disc or
you want to edit the disc after recording, select a
rewritable DVD-RW or DVD-RAM type disc. If you
want to save a recording without any changes,
choose a non-rewritable DVD-R.
Step 4
Step 2
Format the disc to start recording
Unlike a VCR, the recorder automatically starts formatting when an unused disc is inserted. This is
required for the preparation of recording on a disc.
Playing
You can select the title you want to play in a displayed menu and then immediately start playback.
A DVD consists of sections called titles, and sub
sections called chapters.
During recording, a title is created between two
points where you start and stop recording. Chapters
will be created automatically when you finalize
recording on DVD-R / DVD-RW discs in Video mode.
The chapter’s length (interval between chapters)
varies according to the recording mode.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video
Recording format (VR mode). You can edit recorded
images and create a playlist in a specific sequence
according to your requirements.
Using a DVD-RW
This type of disc can be formatted in either DVDVideo format (Video mode) or DVD-Video Recording
format (VR mode). For an unused disc, a message
that asks whether to format in VR Mode or not is displayed. You can play a video mode disc on various
DVD components. A VR mode disc allows more varied editing.
Using a DVD-R
This type of disc can be formatted in DVD Video format. After formatting is complete, you can record on
the disc. You can play this type of disc on various
DVD components only when they have been finalized.
■ You can only use either the VR or Video
Note
mode on a DVD-RW, but not both at the
same time.
■ You can change the DVD-RW format to
another format by reinitializing.
It should be noted that the disc's data will
be lost when changing formats.
Step 5
Editing a recorded disc
Editing on discs is easier than conventional video
tapes. The recorder supports many different edit
functions, possible only with DVDs.
With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Creating a playlist (DVD-RAM/-RW in VR
mode)
With this recorder, you can create a new playlist on
the same disc and edit it without the change of the
original recording.
English - 9
Getting Started
Step 1
Step 3
00588A(00)-VR320-1/XAA-eng
Getting Started
Step 6
6/7/05
7:08 PM
Page 10
Finalizing & Playing on
other DVD components
To play your DVD on other DVD components, finalizing may be necessary. First, finish all editing and
recording operations, then finalize the disc.
When using a DVD-RW disc in VR Mode
Although finalizing is generally unnecessary when
playing the disc on a VR Mode compatible component, a finalized disc should be used for playback.
When using a DVD-RW disc in Video Mode
The disc should be finalized first to enable playback
on anything other than this recorder. No more editing
or recording can be made on the disc once it has
been finalized.
When using a DVD-R disc
You should finalize the disc to play it on a component
other than this recorder. You cannot edit or record on
the disc once it has been finalized.
10 - English
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 11
Description
Getting Started
Front Panel
1.
2.
3.
4.
5.
6.
7.
8.
11
10
DVD DECK
DVD OPEN/CLOSE BUTTON
VCR DECK
VCR EJECT BUTTON
POWER BUTTON
P.SCAN BUTTON
VIDEO INPUT JACK (AV IN 2)
AUDIO L, R INPUT JACKS (AV IN 2)
9.
10.
11.
12.
13.
14.
15.
12
13
14
15
DV INPUT JACK
FRONT PANEL DISPLAY
DVD/VCR SELECT BUTTON
RECORD BUTTON
CHANNEL / BUTTONS
COPY BUTTON
PLAY/STILL, REW/SKIP, F.F/SKIP, STOP,
BUTTONS
Front Panel Display
1.
2.
3.
4.
5.
6.
DVD is activated.
DVD-RAM is activated.
DVD-R or DVD-RW is activated.
Progressive Scan mode is activated.
Record function is activated.
VCR is activated.
10
7. DVD or CD media is loaded.
8. The time, counter position or current deck
status is indicated.
9. When you set a Timer recording,
this indicator is it.
10. VHS Videotape is loaded.
English - 11
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 12
Getting Started
Rear Panel
6 7
Fan
The fan always revolves when the power is on.
Ensure a minimum of 4” clear space on all sides of the fan
when installing the product.
1.
2.
3.
4.
5.
AUDIO L, R OUT JACKS
(COMPONENT OUT)
DIGITAL AUDIO OUT JACK (OPTICAL)
DIGITAL AUDIO OUT JACK (COAXIAL)
VIDEO OUT JACKS (COMPONENT OUT)
S-VIDEO IN/OUT JACKS
12 - English
6.
7.
8.
9.
10.
11.
9 10
11
VIDEO INPUT JACK (AV IN 1)
AUDIO L, R INPUT JACKS (AV IN 1)
AUDIO L, R OUT JACKS(AV OUT)
VIDEO OUT JACK(AV OUT)
ANT OUT (TO TV) JACK
ANT IN JACK
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 13
Tour of the Remote Control
18
19
20
21
22
23
24
10
25
26
11
12
13
14
15
16
17
27
28
29
30
31
32
1. POWER Button
2. NUMBER Button
3. 100+ Button
Press this to select channel 100 or higher.
4. VCR Button
Press this when you use a VCR.
5. DVD Button
Press this when you use a DVD.
6. TV Control Buttons
• VOLUME Button
TV volume adjustment
• CHANNEL Button
Press this to select a TV channel.
• TRK Button
Press this to remove the white line.
7. F.ADV/SKIP Button
8. Playback-related Buttons
Forward/Rewind, Search, Skip, Stop, Play/Pause
9. TITLE LIST(DISC MENU) Button
Press this to enter the TITLE list/Disc menu.
10. MENU Button
Press this to bring up the DVD Recorder & VCR’s
setup menu.
11. ENTER/DIRECTION Buttons
(UP/DOWN or LEFT/RIGHT Buttons)
This button functions as a toggle switch.
❚ Key Lock Function
If you do not want others to operate the DVD Recorder &
VCR (for example if you have programmed a timer recording)
you can set the equipment to lock out all button controls.
• Press and hold the INFO. button on the remote control for 5
seconds.
The display will show “SAFE” when the feature is activated.
• To resume normal mode, press and hold the INFO. button
again for 5 seconds.
“SAFE” will disappear and the DVD Recorder & VCR will
operate normally.
English - 13
Getting Started
12. RETURN Button
Returns to a previous menu.
13. TV/VCR Button
14. INFO Button
Press this to display current setting or disc status.
15. REC Button
Press this to make a recording on VCR, DVD-RAM/RW/-R discs.
16. DVD COPY Button
Press this when you copy from the VCR
to the DVD.
17. REC SPEED Button
Use this to set the desired recording time and
picture quality.
18. TV POWER Button
19. AUDIO/TV MUTE Button
Press this to access various audio functions.
This operates as sound mute. (TV mode)
20. TV Button
Press this to operate TV.
21. INPUT SEL. Button
Press this to select AV input signal in external input
mode.(Tuner, AV input, DV input)
22. OPEN/CLOSE Button
Press this to open and close the disc tray.
23. TIMER REC Button
Press this when you use Timer Recording.
24. MARKER Button
Press this to bookmark or mark a position while
playing a disc.
25. PLAY LIST(TITLE MENU) Button
Press this to enter the Edit playlist/Title menu.
26. ANYKEY Button
Press this to view the status of the disc that is being
played.
27. CLEAR Button
28. SUBTITLE Button
Press this to switch the DVD’s subtitle language.
29. ANGLE Button
Press this to access various camera angles on a
disc (if the disc contains multiple camera angles).
30. ZOOM Button
Zooms in on screen.
31. VCR COPY Button
Press this when you copy from the DVD to the VCR.
32. REC PAUSE Button
Press this to pause during recording.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 14
Connections
Connecting &
Setting Up
Quick Overview
A Quick overview presented in this guide will give you
enough information to start using the recorder.
Step 1 : Unpacking
†
Step 2 : Connecting the Antenna Cable
†
Step 3 : Connecting the Video Cable
†
Step 4 : Connecting the Audio Cable
†
Step 5 : Connecting External Devices
†
Step 6 : Connecting the Power Cord
†
Step 7 : Preparing the Remote Control
Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Step 1 : Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Step 2 : Connecting the Antenna cable . . . . . . . . . . . . . . . . .15
Step 3 : Connecting the Video cable . . . . . . . . . . . . . . . . . . .16
Step 4 : Connecting the Audio cable . . . . . . . . . . . . . . . . . . .18
Step 5 : Connecting External Devices . . . . . . . . . . . . . . . . . .19
• Note to CATV system installer : This reminder is
to call CATV system installer’s attention to Article 820-40
of the National Electrical Code (Section 54 of Canadian
Electrical Code, Part I), that provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
Step 6 : Connecting the Power Cord . . . . . . . . . . . . . . . . . . .20
system of the building as close to the point of cable title
Step 7 : Preparing the Remote Control . . . . . . . . . . . . . . . . .20
as practical.
14 - English
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 15
Step 1: Unpacking
Method1 : Antenna + DVD Recorder &
VCR + TV : No Cable box
You can record non-scrambled channels by selecting the
channel on the DVD Recorder & VCR. Also use this
Method if you watch channels without a cable box.
Accessories
Connections
Check for the supplied accessories below.
• Video/Audio Cable (AC39-00073A)
• RF Cable for TV (AC39-42001J)
• Remote Control (AK59-00034H)
• Batteries for Remote Control (AAA Size)
(AC43-12002H)
• User’s Manual
• Quick Guide
Step 2: Connecting the
Antenna Cable
RF Cable
There are several ways to connect your DVD Recorder &
VCR. Select one of the following antenna connections
that best suits you below.
• Method 1 : Antenna + DVD Recorder & VCR + TV : No
Cable box
• Method 2 : Antenna +Cable box + DVD Recorder &
VCR + TV : Cable box with many scrambled
channels
• Method 3 : Antenna + DVD Recorder & VCR + Cable
box + TV : Cable box with a few scrambled
channels
Method 2 : Antenna +Cable box +
DVD Recorder & VCR + TV : Cable box
with many scrambled channels
You can record channels by selecting the channel on the
cable box. You cannot record one channel while watching
another channel. Be sure that the cable box is turned on.
Wall
■ If you are using an off-air antenna that has 300Note
ohm twin flat leads, use an external antenna
connector (300-75 ohm adaptor : not supplied)
to connect the antenna to the DVD Recorder &
VCR.
Cable box
To RF IN
■ If you have two separate antennas (one VHF
and the other UHF), use a UHF/VHF combineradaptor (available at most electronics shops) to
connect the antenna to the DVD Recorder &
VCR.
To RF OUT
RF Cable
To ANT INPUT
English - 15
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 16
Method 3 : Antenna + DVD Recorder &
VCR + Cable box +TV : Cable box with
a few scrambled channels
You can record non-scrambled channels by selecting the
channel on the cable box. You cannot record scrambled
channels that require a cable box.
Connections
Wall
To RF IN
To RF OUT
Cable box
RF Cable
To ANT INPUT
Step 3: Connecting the
Video Cable
There are several ways to connect your DVD Recorder
& VCR. Select one of the following video connecting
methods that best suits you below.
• Method 1 : Connecting to a Video input jack
• Method 2 : Connecting to an S-video input jack
• Method 3 : Connecting to Component video input
jacks (Y, PB, PR )
S-Video, Component video and Progressive
Output Modes
• S-Video and Component video output are available
only if your TV supports S-Video input or Component
video input, respectively. If S-Video or Component
video output does not work, check the TV connections
and the TV input selection settings.
16 - English
• Compared to standard interlaced video, progressive
scan doubles the amount of video lines fed to your TV,
resulting in a more stable, flicker-free, and clear image
than interlaced video. The progressive scan video output jack is used in progressive output mode. This is
only available with TVs that support progressive scan.
• Consumers should note that not all high definition television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. If
you experience 480 progressive scan picture problems, it is recommended that you switch the connection to the ‘standard definition’ output. If there are
questions regarding TV set compatibility with this
model, please contact our customer service center at
1-800-SAMSUNG.
Method 1 : Connecting to a video input jack
Connect a video(yellow) cable between the VIDEO OUT
jack (AV OUT) on DVD Recorder & VCR and VIDEO
(yellow) IN jack on the TV(or AV amplifier).
• You will enjoy regular quality images.
• Connect audio cables (white and red) between the
AUDIO L, R OUT Jacks (AV OUT) on the DVD
Recorder & VCR and AUDIO IN jacks on TV (or AV
amplifier).
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 17
Method 2 : Connecting to an S-video
input jack
Connect an S-video cable(not included) between the
S-VIDEO OUT jack on DVD Recorder & VCR and
S-VIDEO IN jack on your TV (or AV amplifier).
• You will enjoy high quality images. S-Video separates
the picture element into black and white (Y) and color
(C) signals to present clearer images than regular
video input mode.
• Connect audio cables(white and red) between the
AUDIO L, R OUT Jacks (AV OUT) on the DVD
Recorder & VCR and AUDIO IN jacks on TV(or AV
amplifier). (See pages 18 to 19)
Connections
COMPONENT
• You will enjoy high quality accurate color reproduction
images. Component video separates the picture
element into black and White(Y), blue(PB), red(PR)
signals to present most clear and clean images.
INPUT
■ Make sure that the color coded connections
S-VIDEO
Note
match. That is, the Y, PB and PR component
output jacks of your DVD Recorder & VCR
should be connected to the exact corresponding component input jacks on your TV.
Otherwise, red or blue images will be displayed
on the TV screen.
■ Make sure that the left and right audio output
Method 3 : Connecting to Component
video input jacks(Y,PB,PR)
jacks of your DVD Recorder & VCR are connected to the left and right audio input jacks of
your TV, respectively.(page 18)
Your TV must support progressive scan input to allow
you to watch progressive scan component video output.
1. Connect Component video cables(not included)
between the VIDEO OUT jacks (COMPONENT OUT)
on DVD Recorder & VCR and COMPONENT VIDEO
IN jacks on your TV (or AV amplifier).
2. Press the P.SCAN button on the front panel while the
unit is in Stop mode. The message [Press “Yes” to
confirm Progressive scan mode. Otherwise press
“No”.] will be displayed.
Press the œ √ buttons to select Yes, and then press
the ENTER button. Make sure that the disc has
stopped completely before changing the mode.
English - 17
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 18
Step 4 : Connecting the
Audio Cable
Method 2 : Connecting to a stereo
amplifier with analog input jacks
If your stereo amplifier only has audio input jacks
(L and R), use the analog audio out jacks on the
DVD Recorder & VCR.
Connections
There are several ways to connect your DVD Recorder
& VCR. Select the audio connection that best suits you
below.
• Method 1 : Connecting to your TV
• Method 2 : Connecting to a stereo amplifier (analog
audio out)
• Method 3 : Connecting to an AV amplifier with a digital input jack.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Method 1 : Connecting to your TV
Method 3 : Connecting to an AV amplifier with the digital input jack
If your TV has audio input jacks, use this connection.
If your AV amplifier has a Dolby Digital or DTS
decoder and a digital input jack, use this connection.
To enjoy Dolby Digital or DTS sound, you will need to
set up the audio settings. (See page 28)
18 - English
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 19
Step 5 : Connecting
External Devices
You can use the AV IN 2 jacks on the front panel
of the DVD Recorder & VCR. You can record from connected as a camcorder.
When an input source is inserted into AV IN 2 while
viewing TV, the input will be switched to AV IN 2 automatically.
Connections
This allows you to connect your DVD Recorder & VCR to
other external devices and view or record their outputs.
• Method 1 : Connecting a VCR, Set-Top Box(STB) or
DVD player to the AUDIO/VIDEO AV IN 1
jacks.
• Method 2 : Connecting a Camcorder to the AV IN 2 in
jacks.
• Method 3 : Connecting a Camcorder to the DV IN
jack.
Method 2 : Connecting a Camcorder to
the AV IN 2 jacks
Method 1 : Connecting a VCR,
Settop Box(STB) or DVD player to the
AUDIO/VIDEO AV IN 1 jacks
Connecting a VCR or external device to AV IN 1 jacks
of the DVD Recorder & VCR.
You can record from connected equipment (VCR, STB
or DVD).
Method 3 : Connecting a Camcorder to
the DV IN jack
If your camcorder has a DV output jack, connect it to
the DV input jack of your DVD Recorder & VCR.
■ You can also use the AV IN 2 jacks on the front
Note
panel of the DVD Recorder & VCR.
■ When the S-Video jack and Video jack are
both connected, the S-Video jack will have priority. Line Selection will be automatically done.
■ Copy protected content cannot be recorded.
English - 19
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 20
Step 6 : Connecting
the Power Cord
Connections
After all connections are complete, plug the power cord
in the wall outlet.
“Auto” appears in the front panel display. This
means that the current time is being set automatically through the antenna under connection(Auto
Program). The setup may take several minutes.
When the DVD Recorder & VCR operates normally, the
current time is automatically set and displayed in the
front panel display.
Step 7 : Preparing the
Remote Control
Install Batteries in the Remote Control
• Open the battery cover on the back of the
remote control.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
• Replace the battery cover.
If the remote control does not operate
properly:
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if the remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local
environmental regulations. Do not put them in
the household trash.
20 - English
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Setting the Remote Control
You can control part of another manufacturer’s TV
functions with this remote control.
• Control function buttons involve : TV POWER,
CH/TRK ( / ), VOL +/-, Direct number buttons,
TV MUTE, INPUT SEL.
Page 21
To determine whether your television is
compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press the TV button and enter the two-figure code
corresponding to the brand of your television, by
pressing the appropriate number button.
Codes
01,14,15,23,31
19
21
30
10
11
06,08,18
28
04
MITSUBISHI 13
Brand
NEWSAN
NOBLEX
PANASONIC
RCA
SANYO
SHARP
SONY
TELEFUNKEN
TOSHIBA
Codes
27
25
12,24
07,29
05,20
02,16,22
03
26
09
ZENITH
17
Result: If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the remote
control.
■ If several codes are indicated for your
Note
television brand, try each one in turn until you
find one that works. If you replace the remote
control’s batteries, you must set the brand code
again.
You can then control the television using the
following buttons.
Button
TV POWER
INPUT SEL.
VOL +/-
Function
Used to switch the television on and off.
Used to select an external source.
Used to adjust the volume of the television.
CH/TRK ( / ) Used to select the desired channel.
TV MUTE
Used to toggle the sound on and off.
0~9
Used to input number directly.
100+
Used to select channels over 100.

 The various functions may not necessarily work
Note
on all televisions. If you encounter problems,
operate the television directly.
English - 21
Connections
Brand
SAMSUNG
DAEWOO
EMERSON
GRADIENTE
HITACHI
JVC
LG
LOEWE
MAGNAVOX
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 22
System Setup
On-Screen Menu
Navigation
The on-screen menus allow you to enable or disable
various functions on your DVD Recorder & VCR.
Use the following buttons to open and navigate through
the on-screen menus.
No Disc
Setup
System Setup
Timer Rec.
MOVE
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
MENU Button
Press this button on the remote control to open
the on-screen MENU. Press again to exit the
on-screen MENU.
…/†,œ /√ Buttons
Press these buttons on the remote control to
move the selection bar …/†,œ /√ to cycle through
the menu options.
ENTER Button
RETURN Button
Press this button on the remote control to confirm
any new settings.
On-Screen Menu Navigation..............................................22
Auto Clock Set ..................................................................23
Manual Clock Set ..............................................................24
Channel Set .......................................................................25
Auto Channel Memory.......................................................25
Channel Add/Delete ..........................................................26
RF Output Channel............................................................26
Setting Up the Language Options .....................................27
Setting Up the Audio Options ...........................................28
Setting Up the Display (Video) Options ............................29
Setting Up the Parental Control ........................................30
VCR Setting ......................................................................31
Video Input .......................................................................32
Front Display ....................................................................33
DVD EP Mode Time .........................................................33
Automatic Chapter Creator ...............................................34
22 - English
Press this button on the remote control to return to
the previous MENU screen displayed or to exit the
on-screen MENU.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 23
Press the …† buttons to select Auto Clock Set,
then press the ENTER or √ button.
Auto Clock Set
No Disc
Setup
Timer Rec.
Auto Clock Set
Clock Data CH
: Automatic
√
Time Zone
: Automatic
√
Daylight Saving
: Automatic
√
This menu is used to set the current time. You need to
set the time to use timer recording.
MOVE

 You must have the antenna connected to set
Note
With the unit in Stop mode/No Disc mode, press
the MENU button.
No Disc
Setup
Timer Rec.
MOVE
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
Press the …† buttons to select Setup, then press
the ENTER or √ button.
RETURN
EXIT
■ If your clock is set to the wrong time zone or
Note
daylight saving, you can adjust these settings
without turning off the Auto Clock Set function.
Press the …† buttons to select the sub menu
(Clock Data CH, Time Zone or Daylight Saving),
then press the ENTER or √ button.
Clock Data CH
Press the …† buttons to select a channel that
carries a time signal, then press the ENTER button.
Select Auto to set the channel automatically.
No Disc
Clock Data CH
Setup
No Disc
Setup
Timer Rec.
MOVE
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
Timer Rec.
MOVE
Select channel :
SELECT
Auto
RETURN
EXIT
EXIT
Time Zone
Press the …† buttons to select Clock Set, then
press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Clock Set
Auto Clock Set
√
Manual Clock Set
√
Press the …† buttons to select the time zone of
your area, then press the ENTER or √ button.
Select Automatic to set the time zone automatically.
No Disc
Setup
Timer Rec.
Auto Clock Set
Clock Data CH
Automatic
Time Zone
Atlantic
Daylight Saving
Eastern
Central
Mountain
MOVE
SELECT
RETURN
EXIT
Pacific
Alaska
Hawaii
MOVE
SELECT
RETURN
EXIT
English - 23
System Setup
the Auto Clock. See pages 15~16 for Antenna
Connections.

 The Clock will be automatically set when you
turn off the recorder.
SELECT
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 24
Daylight Saving
Press the …† buttons to select Automatic,
Yes or No, then press the ENTER or √ button.
Select Automatic to set the daylight saving
automatically.
No Disc
Setup
Timer Rec.
Press the …† buttons to select Clock Set, then
press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Clock Set
Auto Clock Set
√
Manual Clock Set
√
Auto Clock Set
Clock Data CH
: Automatic
√
Time Zone
: Automatic
√
Daylight Saving
Automatic
Yes
MOVE
SELECT
RETURN
EXIT
No
MOVE
SELECT
RETURN
EXIT
System Setup
Manual Clock Set
Press the …† buttons to select Manual Clock
Set, then press the ENTER or √ button.
No Disc
Manual Clock Set
Setup
Timer Rec.
Date (mm/dd/yy)
01 / 01 / 2005 SAT
Time
12 : 00 AM
Press numeric keys or
If Auto Setup fails to set the DVD Recorder & VCR’s internal clock by locating a local TV station, follow these steps
to set the date and time manually.
Note
For accurate Timer Recording, your DVD Recorder
& VCR's internal clock must be set correctly.
With the unit in Stop mode/No Disc mode, press
the MENU button.
No Disc
Setup
Timer Rec.
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
SELECT
√
RETURN
EXIT
Press the …† buttons to select Setup, then press
the ENTER or √ button.
No Disc
Setup
Timer Rec.
MOVE
24 - English
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
MOVE
SELECT
RETURN
…†
keys.
EXIT
Press the …†œ √ buttons to select the Current Date
and Current Time, then press the ENTER button.
When the current time is stored in memory and
then the set is powered off, the current time will
appear in the front panel display.
…† : Sets the value
You can set the value using the number (0~9)
buttons.
œ √: Moves to items
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 25
Channel Set
Press the …† buttons to select Antenna/Cable
TV, then press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Channel Set
Antenna/Cable TV
Antenna
Auto Channel Memory
Cable TV
√
Channel Add/Delete
√
RF Output Channel
This feature allows you to manually set the DVD
Recorder & VCR’s tuner band to Antenna or Cable,
whichever you connected to the Antenna In jack during
initial setup.
• Use this setting only if Auto Setup detected the
incorrect tuner band, i.e. channels are coming in on
the wrong channel numbers.
Setup
Timer Rec.
MOVE
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
• Cable TV - Select if the DVD Recorder & VCR is
connected to Cable TV(method 2).
Auto Channel Memory
EXIT
Press the …† buttons to select Setup, then press
the ENTER or √ button.
No Disc
Setup
Timer Rec.
MOVE
EXIT
• Antenna - Select if the DVD Recorder & VCR is
connected to an indoor or outdoor VHF/UHF
Antenna(method1 and 3).
Setup
System
RETURN
Select the Antenna/Cable TV(Signal Source) that
matches the antenna connection you selected on
pages 15~16(method1, 2 and 3).
With the unit in Stop mode/No Disc mode, press
the MENU button.
No Disc
SELECT
√
Auto Channel Memory will automatically seek and store
all active channels in your area.
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
Press the …† buttons to select Channel Set,
then press ENTER or √ button.
No Disc
Setup
Timer Rec.
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
Press the …† buttons to select Channel Set,
then press the ENTER or √ button.
Channel Set
Antenna/Cable TV
: Cable TV
Auto Channel Memory
√
Channel Add/Delete
RF Output Channel
√
No Disc
Setup
√
: CH3
√
Timer Rec.
Channel Set
Antenna/Cable TV
: Cable TV
Auto Channel Memory
MOVE
SELECT
RETURN
√
Channel Add/Delete
RF Output Channel
√
√
: CH3
√
EXIT
MOVE
SELECT
RETURN
EXIT
English - 25
System Setup
MOVE
: CH3
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 26
Press the …† buttons to select Auto Channel
Memory, then press the ENTER or √ button.
No Disc
Setup
Timer Rec.
No Disc
Auto Channel Memory
Total channel numbers:
Saved channel : 05
Press the …† buttons to select Channel
Add/Delete, then press the ENTER or √ button.
Channel Add/Delete
Setup
06/125
Timer Rec.
Select channel :
5%
Scanning...
Add
Delete
Stop
System Setup
MOVE
SELECT
RETURN
NUMBER
EXIT
• The DVD Recorder & VCR will automatically
search for all available channels in the selected
tuner band. This procedure may take a few minutes to complete.
• When finished, the lowest channel found will be
displayed.
• Press ENTER button to stop or cancel scanning.
Channel Add/Delete
SELECT
RETURN
EXIT
Press the …† or number buttons to select the
channels you want to add or delete on the Select
channel screen. Then, press the ENTER button.
• Using …† buttons for channel selection allows
the user to add/delete one channel at a time.
• Using CH/TRK ( / ) buttons for channel
selection jumps to the next channel memorized
in Auto Channel Memory.
Press the œ √ buttons to select Add or Delete,
then press the ENTER button.
No Disc
Channel Add/Delete
Setup
Timer Rec.
Select channel :
11
Channel is added.
Use this feature if Auto Channel Memory missed a
channel that you would like to add and delete a channel
you wish to remove.
Add
NUMBER
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
Press the …† buttons to select Channel Set, then
press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Channel Set
Antenna/Cable TV
: Cable TV
Auto Channel Memory
MOVE
26 - English
SELECT
RETURN
EXIT
RF Output Channel
When you connect the DVD Recorder & VCR to TV
with RF Antenna Cable, follow the steps below to set
the RF Output Channel.
√
√
Channel Add/Delete
RF Output Channel
SELECT
Delete
√
: CH3
RETURN
√
EXIT
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
00588A(00)-VR320-1/XAA-eng
6/7/05
Page 27
Press the …† buttons to select Channel Set,
then press ENTER or √ button.
No Disc
Setup
Timer Rec.
MOVE
: Cable TV
Auto Channel Memory
√
Channel Add/Delete
√
SELECT
Setup
Timer Rec.
: CH3
RETURN
No Disc
Timer Rec.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
No Disc
√
√
EXIT
MOVE
Press the …† buttons to select RF Output
Channel, then press the ENTER or √ button.
Setup
Channel Set
Antenna/Cable TV
RF Output Channel
7:08 PM
Channel Set
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
Press the …† buttons to select Language, then
press the ENTER or √ button.
Language setup menu will be displayed.
Antenna/Cable TV
Auto Channel Memory
√
Channel Add/Delete
√
RF Output Channel
:CH3
CH3
No Disc
Setup
√
Timer Rec.
SELECT
RETURN
Language
Audio
: Original
√
Subtitle
: Automatic
√
Disc Menu
: English
√
On-Screen Menu
: English
√
System Setup
CH4
MOVE
Setup
System
EXIT
MOVE
Press the …† buttons to select CH3/CH4, then
press the ENTER or √ button.
A message will appear on your TV.
When the message disappears, change your TV
to channel 3 or 4 to match the RF Output Channel
of the player.
SELECT
RETURN
EXIT
Press the …† buttons to select the desired
language option, press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Language
Audio
Original
Subtitle
English
Français
Disc Menu
On-Screen Menu
Deutsch
Español
Italiano
Nederlands
Korean
Setting Up the
Language Options
If you set audio, subtitle, disc menu and on-screen
menu language in advance, they will come up
automatically every time you watch a movie.
If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
MOVE
SELECT
RETURN
EXIT
• Audio : For the disc audio language.
• Subtitle : For the disc subtitles.
• Disc Menu: For the disc menu contained on the
disc.
• On-Screen Menu: For the on-screen menu of
your DVD Recorder & VCR.
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select the desired
language, then press the ENTER or √ button.
■ Press the RETURN or œ button to return to the
Note
previous menu. Press the MENU button to exit the
menu.
■ The selected language will only appear if it is
supported on the disc.
English - 27
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 28
Setting Up the Audio
Options
Digital Output
1. PCM :
2. Bitstream :
Allows you to setup the audio device and sound staus
settings depending on the audio system in use.

 Be sure to select the correct Digital Output or
Note
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
no audio will be heard.
DTS
No Disc
Setup
System Setup
Converts to PCM(2CH) 48kHz
audio. Select PCM when using the
Analog Audio Outputs.
Converts to Dolby Digital Bitstream
(5.1CH). Select Bitstream when
using the Digital Audio Outputs.
Timer Rec.
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
MOVE
SELECT
1. Off : Doesn’t output digital signal.
2. On : Outputs DTS Bitstream via digital output
only. Select DTS when connecting to a DTS
Decoder.

 When DTS soundtrack is played, sound is not
Note
output from Analog Audio Output.
√
RETURN
EXIT
Dynamic Compression
Press the …† buttons to select Audio, then press
the ENTER or √ button.
Audio setup menu will be displayed.
No Disc
Setup
Timer Rec.
MOVE
Audio
Digital Output
: PCM
√
DTS
: Off
√
Dynamic Compression
: On
√
SELECT
RETURN
EXIT
Press the …† buttons to select the desired audio
option, then press the ENTER or √ button.
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
■ Press the RETURN or œ button to return to the
Note
previous menu.
Press the MENU button to exit the menu.
28 - English
This is only active when a Dolby Digital signal is
detected.
1. Off : You can enjoy the movie with the standard
Dynamic Range.
2. On : When the Movie soundtracks are played at
low volume or from smaller speakers, the
system can apply appropriate compression to
make low-level content more intelligible and
prevent dramatic passages from getting too
loud.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 29
Setting Up the
Display(Video) Options
This function allows you to setup the TV screen
settings.
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
No Disc
Setup
MOVE
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
Press the …† buttons to select Video, then press
the ENTER or √ button.
Video option menu will be displayed.
No Disc
Setup
Timer Rec.
Video
TV Aspect
: 16:9 Wide
√
Input Level
: Darker
√
Black Level
: 7.5 IRE
√
3D Noise Reduction : Off
MOVE
SELECT
RETURN
Depending on the type of television you have, you
may want to adjust the screen setting. (aspect ratio)
• 4:3 Letter Box : Select when you want to see the
total 16:9 ratio screen DVD supplies, even though you have a
TV with a 4:3 ratio screen. Black
bars will appear at the top and
bottom of the screen.
• 4:3 Pan - Scan : Select this for a conventional
size TV when you want to see
the central portion of the 16:9
screen. (Extreme left and right
side of movie picture will be cut
off.)
• 16:9 Wide : You can view the full 16:9 picture on
your widescreen TV.
Input Level
Adjusts the level of the input signal.
• Darker : If you feel the screen is too light
and you want to make the sceen
darker.
• Lighter : If you feel the screen is too dark
and you want to make the sceen
lighter.
Black Level
Adjusts the black level of the screen.
√
EXIT
Press the …† buttons to select the desired video
option, then press the ENTER or √ button.
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
• 0 IRE : This is the standard NTSC reference black
level for consistent brightness/
contrast across all sources.
Select this when you want darker screen.
• 7.5 IRE : This will enhance the black level for
increased brightness/contrast when
viewing DVDs.
Select this when you want lighter screen.
3D Noise Reduction
• Off : Normal
• On : Select to remove noise from the screen.

 Press the RETURN or œ button to return to the
Note
previous menu. Press the MENU button to exit
the menu.

 This function depends on disc type. It may not
Note
work for some disc types.

 IRE: Short for the Institute of Radio Engineers. An
IRE unit is a relative unit of measure equaling 1/140th of the peak-to peak (p-p) video
amplitude.
English - 29
System Setup
Timer Rec.
Setup
System
TV Aspect
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 30
Setting Up the Parental
Control
The Re-enter Password screen appears to confirm
the password. Enter your password again, and
then press the ENTER or √ button.
No Disc
Setup
Parental Control
Password
Off
On
Timer Rec.
The Parental Control function works in conjunction with
DVDs that have been assigned a rating - which helps
you control the types of DVDs that your family watches.
There are up to 8 rating levels on a disc.
With the unit in Stop mode/No Disc mode, press
the MENU button on the remote control.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
System Setup
No Disc
Setup
Timer Rec.
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
SELECT
SELECT
RETURN
Press the …† buttons to select On, then press
the ENTER or √ button.
The Parental Control screen appears.
previous menu. Press the MENU button to exit the
menu.

 Refer to Troubleshooting if you forget your password. (See page 83)
About the Rating Level
√
RETURN
EXIT
Press the …† buttons to select Rating Level,
then press the ENTER or √ button.
No Disc
EXIT

 Press the RETURN or œ button to return to the
Note
Setup
System
Parental Control
MOVE
MOVE
Press the …† buttons to select Parental Control,
then press the ENTER or √ button.
Setup
Timer Rec.
Parental Control
Password
: On
√
Rating Level
: Level 1 kids
√
Change password
No Disc
√
Parental Control
Setup
Timer Rec.
Create the password
MOVE
SELECT
RETURN
No Disc
Setup
NUMBER
SELECT
RETURN
EXIT
Timer Rec.
EXIT
Parental Control
Password
Level 8 Adults
Rating Level
Level 7
Change password
Level 6
Level 5
Level 4
Level 3
Create a 4-digit password using the 0 to 9 buttons
on the remote control.
Level 2
Level 1 Kids
MOVE
No Disc
SELECT
RETURN
EXIT
Parental Control
Setup
Timer Rec.
Confirm the password
NUMBER
30 - English
SELECT
RETURN
EXIT
Press the …† buttons to select the rating level
you want, then press the ENTER or √ button.
For example, if you select up to Level 6, discs that
contain Level 7, 8 will not play. A larger number
indicates that the program is intended for adult
use only.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 31
About the Change Password
VCR Setting
Press the …† buttons to select Change Password,
then press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Parental Control
Password
: On
√
Rating Level
: Level 1 kids
√
Change password
If you want your videotapes to play automatically when
you insert them, turn on Auto Play.
√

 Only tapes that are missing the Record Safety
MOVE
SELECT
No Disc
RETURN
EXIT
Change Password
Setup
Note
Tab will play automatically when inserted.
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
Timer Rec.
Enter the password
SELECT
RETURN
No Disc
EXIT
Setup
Timer Rec.
Enter the 4-digit password using the 0 to 9 buttons
on the remote control.
The ‘Confirm the password.’ message will be displayed.
No Disc
MOVE
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
EXIT
Change Password
Setup
Timer Rec.
Press the …† buttons to select System, then
press the ENTER or √ button.
Confirm the password
No Disc
Setup
Timer Rec.
NUMBER
SELECT
RETURN
EXIT
Enter your password again using the 0 to 9 buttons
on the remote control.

 Press the RETURN or œ button to return to the
Note
previous menu.
Press the MENU button to exit the menu.
MOVE
System
VCR
√
Video Input
: AV 1
√
Front Display
: Auto Dim
√
DVD EP Mode Time
: 6Hours
√
Chapter Creator
: Off
SELECT
RETURN
√
EXIT
Press the …† buttons to select VCR, then press
the ENTER or √ button.
No Disc
Setup
Timer Rec.
MOVE
VCR
Tape Length
:T120
√
Auto Play
: On
√
Auto Repeat
: Off
√
SELECT
RETURN
EXIT
English - 31
System Setup
NUMBER
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 32
Press the …† buttons to select the desired VCR
option, then press the ENTER or √ button.
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
If you watch video through AV IN 1, you can choose
AV 1(Composite) or S-video.
Tape Length
This information is usually printed on the tape box.
The menu cycles through: T-120, T-160 or T-180.
Once the type of cassette is set, the VCR can display the amount of time remaining on the tape when
you press the INFO. button.
No Disc
VCR
Setup
System Setup
Auto Play
T-120
: T-120
T-160
: On
Auto Repeat
T-180
: Off
Tape Length
Timer Rec.
Video Input
√
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
√
√
No Disc
Setup
Setup
Timer Rec.
MOVE
SELECT
RETURN
EXIT
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
Auto Play
MOVE
• Off - Auto play is disabled.
• On - The VCR will automatically begin playing a
video tape when it is inserted, as long as the
safety tab of the cassette has been removed.
SELECT
√
RETURN
EXIT
Press the …† buttons to select System, then
press the ENTER or √ button.
No Disc
No Disc
Setup
Timer Rec.
Setup
VCR
: AV 1
√
√
Front Display
: Auto Dim
√
√
DVD EP Mode Time
: 6Hours
√
Chapter Creator
: Off
: T-120
√
Auto Play
: On
Off
Auto Repeat
: Off
On
SELECT
RETURN
Timer Rec.
No Disc
Timer Rec.
Tape Length
: T-120
√
Auto Play
: On
√
Auto Repeat
: Off
Off
√
32 - English
RETURN
MOVE
EXIT
System
VCR
Video Input
AV 1
S-Video
Front Display
VCR
SELECT
EXIT
Press the …† buttons to select Video Input, then
press the ENTER or √button.
Setup
On
MOVE
RETURN
No Disc
It sets the VCR to play a tape repeatedly (unless a
tape control is activated :Stop, Fast Forward or
Rewind).
Timer Rec.
SELECT
√
EXIT
Auto Repeat
Setup
√
Video Input
Tape Length
MOVE
MOVE
System
VCR
DVD EP Mode Time
: 6Hours
Chapter Creator
: Off
SELECT
RETURN
√
√
EXIT
Press the …† buttons to select AV 1 or
S-Video, then press the ENTER or √ button.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 33
Front Display
DVD EP Mode Time
Adjust the brightness of the unit’s front display.
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
No Disc
Setup
MOVE
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
System
√
Clock Set
√
Channel Set
√
Setup
Language
√
Timer Rec.
Audio
No Disc
√
Clock Set
√
√
Channel Set
√
Video
√
Language
√
Parental Control
√
Audio
√
Video
√
SELECT
RETURN
EXIT
Parental Control
MOVE
Press the …† buttons to select System, then
press the ENTER or √ button.
Press the …† buttons to select Front Display,
then press the ENTER or √ button.
No Disc
Setup
Timer Rec.
Setup
System
System
VCR
SELECT
√
RETURN
Press the …† buttons to select System, then
press the ENTER or √ button.
Press the …† buttons to select DVD EP Mode
Time, then press the ENTER or √ button.
√
No Disc
Video Input
: AV 1
Front Display
Auto Dim
DVD EP Mode Time
Bright
Chapter Creator
:Dim
Off
System
√
Setup
Timer Rec.
√
VCR
√
Video Input
: AV 1
√
Front Display
: Auto Dim
√
Chapter Creator
SELECT
RETURN
Press the …† buttons to select the desired item,
then press the ENTER or √ button.
• Auto Dim – Front Display will dim automatically
during power off.
• Bright –
• Dim –
6Hours
8Hours
: Off
√
EXIT
MOVE
EXIT
DVD EP Mode Time
MOVE
System Setup
Timer Rec.
Setup
You can set the EP(Extended Play)mode’s time setting
to 6 or 8hours.
SELECT
RETURN
EXIT
Press the …† buttons to select 6 Hours or 8
Hours, then press the ENTER or √ button.
Front Display will be bright all the
time.
Front Display will be dim all the time.
English - 33
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 34
Automatic Chapter
Creator
Press the REC button to start recording.
The message "Do you want to create the chapter
menu after this recording?" is displayed.
Press the œ √ buttons to select Yes and press
the ENTER button and recording begins.
In XP and SP mode, you must record at least 5
minutes to create a chapter. In LP and EP mode,
15 minutes.
System Setup
This function only works with DVD-RW (Video mode)
and DVD-R discs.
A DVD-Video consists of ‘Titles’ and ‘Chapters’.
When you record one program, it makes one Title.
If you use this function, the Title will be divided into
Chapters.
With the unit in Stop mode/No Disc mode, press
the MENU button.
Press the …† buttons to select Setup, then press
the ENTER or √ button.
DVD-RW(V)
Setup
Timer Rec.
Copy
Title List
Disc Manager
MOVE
Setup
System
√
Clock Set
√
Channel Set
√
Language
√
Audio
√
Video
√
Parental Control
√
SELECT
RETURN
Press the …† buttons to select System, then
press the ENTER or √ button.
Press the …† buttons to select Chapter Creator,
then press the ENTER or √ button.
DVD-RW(V)
Timer Rec.
Copy
Title List
Previous
11
System
VCR
: AV 1
√
Front Display
: Auto Dim
√
DVD EP Mode Time
: 6Hours
√
Chapter Creator
: Off
Off
√
CHAPTER
On
SELECT
RETURN
EXIT
Press the …† buttons to select On, then press
the ENTER or √ button.
Press the MENU button to exit the menu.
Top
Next

 On DVD-RW discs, additional chapters and
Note
Next
To display the created chapters, select the
desired Title and then press the DISC MENU
button. The chapter menu for the selected Title
will be displayed.
Previous
Top
√
Video Input
Disc Manager
MOVE
To display the created titles, finalize the disc
(see page 79) and then press the TITLE MENU
button. The title menu will be displayed.
EXIT
Setup
Press the STOP button to stop recording.
10
Set the recording speed by pressing the REC
SPEED button on the remote (see page 53 for
more information on recording speeds).
titles can be added to a finalized disc by
unfinalizing and recording again.On DVD-R
discs, once finalized, no additional chapters or
titles can be recorded.

 The Automatic Chapter Creator function does
CAUTION
34 - English
not work during Timer Recording or when you
turn the power off.

 DVD-R discs cannot be unfinalized.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 35
Before Playing
Playback
Read the following information before playing a disc.
This section introduces basic functions of playback by disc type.
Dolby Digital
Stereo
DTS
NTSC broadcast system in U.S.A, Canada,
Korea, Japan,etc.
Region code (DVD-Video only)
Both the DVD Recorder & VCR and the discs are
coded by region. These regional codes must
match in order for the disc to play. If the codes do
not match, the disc will not play. The Region
Number for this DVD Recorder & VCR is
described on the rear panel of the DVD Recorder
& VCR.
Digital Audio
MP3
Disc types that can be played
Disc Types
DVD-VIDEO
AUDIO-CD
Before Playing ...................................................................35
Playing a Disc ...................................................................36
JPEG CD-R/RW
MP3 CD-R/RW
Using the Disc Menu and Title Menu ...............................37
Using the Search & Skip Functions ..................................37
Slow Motion Play / Step Motion Play ...............................38
About ANYKEY .................................................................38
DVD-RAM
Repeat Play........................................................................39
Selecting the Subtitle & Audio Language.........................41
Changing the Camera Angle.............................................42
Zooming-In .......................................................................42
Using the Bookmarks .......................................................43
DVD-RW
Using the Markers ...........................................................44
Playing back an Audio CD (CD-DA)................................45
Playing back an MP3 CD..................................................46
Play Option Mode..............................................................47
To Program Tracks ............................................................47
Playing a picture CD.........................................................48
◆ VCR Playback
Playing the VCR................................................................49
Tracking.............................................................................49
Special VCR Playback Features ........................................49
S-VHS Playback ...............................................................49
Variable Search System.....................................................50
DVD-R
Disc Shape Max. Playing Time
Single sided(5”)
240
Double sided(5”)
480
AUDIO + VIDEO
Single sided(3.5”)
80
Double sided(3.5”)
160
Single sided(5”)
74
AUDIO
Single sided(3.5”)
20
Single sided(5”)
JPEG Images
Single sided(3.5”)
Single sided(5”)
MP3 Audio
Single sided(3.5”)
1 (XP: Excellent Quality)
Single-sided 2 (SP: Standard Quality)
5” (4.7GB) 4 (LP: Long Playback)
6 or 8 (EP:Extended)
AUDIO + VIDEO
2 (XP: Excellent Quality)
Double-sided 4 (SP: Standard Quality)
5” (9.4GB) 8 (LP: Long Playback)
12 or 16 (EP:Extended)
1 (XP: Excellent Quality)
2 (SP: Standard Quality)
AUDIO + VIDEO
5” (4.7GB)
4 (LP: Long Playback)
6 or 8 (EP:Extended)
1 (XP: Excellent Quality)
2 (SP: Standard Quality)
AUDIO + VIDEO
5” (4.7GB)
4 (LP: Long Playback)
6 or 8 (EP:Extended)
Discs that cannot be played
• DVD-Video with a region number other than “1” or
“ALL”
• 3.9 GB DVD-R Disc for Authoring.
• DVD-RAM not recorded following the Video
Recording Standard
• Unfinalized DVD-R,unfinalized DVD-RW(V mode)
• PAL discs
• DVD-ROM/DVD+RW/PD/MV-Disc/DiVX Video Disc, etc
•Video CD/CVD/SVCD/CD-ROM/CDV/CD-G/CD-I
English - 35
Playback
◆ DVD Playback
Disc Logo Recorded content
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 36

 This DVD Recorder & VCR can only operate
Note
with discs that are compatible with DVD-RAM
Standard Version 2.0.
Playback and/or recording may not work for
some types of discs, or when specific operations, such as angle change and aspect ratio
adjustment, are being performed. Information
about the discs is written in detail on the box.
Please refer to this if necessary.
Do not allow the disc to become dirty or
scratched, fingerprints, dirt, dust, scratches or
deposits of cigarette smoke on the recording
surface may make it impossible to use the disc
for recording.
DVD-RAM/-RW/-R discs may not be able to
play on some DVD players, depending on the
player, disc and the condition of the recording.
Discs with PAL programs recorded on them
cannot be recorded using this product.
Press the OPEN/CLOSE button.
Press OPEN/CLOSE button to close the disc tray.
• Your DVD Recorder & VCR closes the disc
tray and plays the disc automatically.
• The recorder does not play discs automatically
after the initial power on.
• When the recorder is powered on and a disc is
in the tray, the unit will be activated and wait in
stop status.
• Press the PLAY button to start playback.
• If you insert an MP3 Disc, your DVD Recorder &
VCR will display the file list on the screen and
start playing.
• If you insert a JPEG Disc, folders and a file list
are displayed.
• If you want the unit to play automatically when it
is powered on with a disc in the unit, power on
with the PLAY button.
Press the STOP button to stop playback.
Playback
Playing a Disc
Place a disc gently into the tray with the disc’s
label facing up.

 When you stop disc play, the DVD Recorder &
Note
VCR remembers where you stopped. When you
press PLAY button again, it will pick up where
you left off. (unless the disc is removed or the
DVD Recorder & VCR is unplugged, or if you
press the STOP button twice.) This function is
only applicable to DVD-VIDEO, DVD-RAM,
DVD-RW, DVD-R or Audio CDs (CD-DA).

 Do not move your DVD Recorder & VCR while
CAUTION
playing, as this may cause damage to the disc.

 Make sure to press the OPEN/CLOSE button to
open or close the disc tray.

 Do not push the disc tray while it is being
opened or closed, as this may cause a product
malfunction.

 Do not place foreign materials on or in the disc
tray.

 Some functions may perform differently or be
disabled depending on the disc type. If this
occurs, refer to the instructions written on the
disc case.

 Be especially careful that children's fingers are
not caught between the disc tray and the tray
chassis when it closes.

 After turning power on, it will take a few
seconds until the DVD Recorder & VCR operates.
36 - English
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 37
Using the Disc Menu
and Title Menu
Some discs contain a dedicated menu system that
allows you to select special functions for title, chapters,
audio track, subtitles, film previews, information on characters, etc.
For DVD-VIDEO disc
Using the Search & Skip
Functions
Searching through a Chapter or Track
During the playback, press the SEARCH œœ or √√
button on the remote control. Each time you press
the SEARCH button, the playback speed will
change as follows.
Press the DISC MENU button to enter the disc
menu of the disc.
DVD-VIDEO/
• Move to the setup menu related to playback operation.
DVD-RAM/DVD-RW
• You can select audio language and subtitle etc.
provided by the disc.
AUDIO CD(CD-DA)
DVD-R
➝FF1/FR1➝FF2/FR2➝ FF3/FR3
• You can scan the program in reverse order.
To return to normal speed playback, press the
√ll button.

 No sound is heard during Scan(Search) mode,
Note
except CDs (CD-DA).
For DVD-RAM/DVD-RW/DVD-R disc
Skipping Chapters or Tracks
Press the TITLE LIST button to display title list.
During the playback, press the lœœ or √√l button
on the remote control.

 Title List : Title List shows a list to help you
Note
select a title. Since the title list consists of the information on video that
is actually recorded, if one title is
deleted, that title cannot be played
again.

 Play List : This refers to a unit of playback,
which is made by selecting a
desired scene in the entire Title
List. When one playlist is played,
only the scene selected by the
user will play and then stop. Since
only the information necessary for
playing a desired scene is included in a playlist, even if that playlist
is deleted, the original recording
will not be deleted.
• If you press the lœœ button
If you press the lœœ button, it moves to the beginning of the chapter, track or marker(DVD-RAM,
DVD-RW(VR mode) ). Pressing the button once
again within 3 seconds returns to the beginning of
the previous chapter, track or marker(DVD-RAM,
DVD-RW(VR mode) ).
• If you press the √√l button
If you press the √√l button, it moves to the next
chapter, track or marker(DVD-RAM, DVD-RW(VR
mode) )
Skipping ahead 30 seconds
During the playback, press F.ADV/SKIP button to
skip ahead exactly 30 seconds.
English - 37
Playback
Press the TITLE MENU button to move to the title
menu of the disc.
• Use this button if the disc contains more than one
title. Some discs may not support the title menu
functionality.
FF1/FR1➝FF2/FR2➝FF3/FR3➝
FF4/FR4➝FF5/FR5➝FF6/FR6
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 38
Slow Motion Play/
Step Motion Play
Slow Motion Play (DVD-VIDEO / DVD-RAM
/ DVD-RW / DVD-R)
About ANYKEY
The ANYKEY functions allows you to easily search for a
desired scene by accessing title, chapter, track and
time. You can also change the subtitle and audio settings and set some features including Repeat, Angle
and Zoom.
During pause mode, press the SEARCH œœ or √√
button on the remote control for more than 1 second.
Moving to a scene directly using
the ANYKEY
• Each time you press the √√ button :
l √ X 1/8 ➝ l √ X 1/4 ➝ l √ X 1/2
• If you want to move to a title, a chapter or a track
to find a desired scene.
• Each time you press the œœ button :
œl X 1/8 ➝ œl X 1/4 ➝ œl X 1/2
Playback
To return to normal speed playback, press the
√ll button.
Step Motion Play (DVD-VIDEO/DVD-RAM /
DVD-RW / DVD-R)
Press the ANYKEY button during playback.
DVD-VIDEO
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Off
1/1
Off
During pause mode, press the F.ADV button on the
remote control.
• Each time the button is pressed, a new frame will
appear.
To return to normal speed playback, press the
√ll button.
MOVE

 No sound is heard during STEP or SLOW
Note
CHANGE
Press the …† buttons to select Title, Chapter or
Track.
DVD-VIDEO
mode.
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Off
1/1
Off
MOVE
38 - English
CHANGE
Press the œ √ buttons or number (0~9) buttons to
select the desired scene.
Then, press the ENTER button.
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 39
• If you want to move to a desired time to help you find
a scene.
Repeat Play
Press the ANYKEY button during playback.
DVD-VIDEO
Playing Repeatedly(Repeat Playback)
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Off
1/1
Off
MOVE
CHANGE
Press the ANYKEY button during playback.
DVD-VIDEO
1/10
Press the …† buttons to select Time.
1/40
00:01:45
Off
ENG
D 5.1CH
Off
DVD-VIDEO
1/1
1/10
Off
1/40
MOVE
00:01:45
CHANGE
Off
ENG
D 5.1CH
Off
1/1
Off
MOVE
NUMBER
Press the …† buttons to select Repeat.
Playback
DVD-VIDEO
1/10
1/40
Enter the time in the sequence of hours, minutes,
and seconds using the number buttons, then
press the ENTER button.
00:01:45
Off
ENG
D 5.1CH
Off
1/1
Off
MOVE

 This may not work for some discs. When an
Note
Audio CD(CD-DA) or an MP3 disc is inserted, according to a disc type, the information
display may not be appear.

 The Time Search function does not operate
in some discs.

 To make the screen disappear, press the
ANYKEY button again.
CHANGE
Select repeat mode using œ √ button.
Press the ENTER button.
• To make the screen disappear, press the
ANYKEY or RETURN button.

 DVD-RAM, DVD-RW(VR mode), unfinalized
Note
DVD-R and unfinalized DVD-RW (Video
mode) do not repeat a chapter.
English - 39
00588A(00)-VR320-1/XAA-eng
6/7/05
7:08 PM
Page 40
Playing Repeatedly(Repeat Playback)
Press the ANYKEY button during playback.
Repeat is highlighted.
CD
Music
Repeat : Off
DVD-VIDEO
1/10
1/40
00:01:45
00 : 52
01/12
MOVE
Press the ANYKEY button during playback.
Play Option : Normal
01. TRACK 1
Playing a Certain section Repeatedly(A-B
Repeat Playback)
SELECT
01. TRACK 1
4:39
02. TRACK 2
4:31
03. TRACK 3
4:30
04. TRACK 4
3:53
05. TRACK 5
4:23
06. TRACK 6
4:24
RETURN
Off
ENG
D 5.1CH
Off
1/1
Off
MOVE
CHANGE
MENU
Press the …† buttons to select the Track or Disc
you want to play repeatedly. Press the ENTER
button.
For MP3 discs, you can select Track, Folder or
Disc.
Press the …† buttons to select Repeat.
DVD-VIDEO
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Off
1/1
Off
Playback
- To return to normal playback -
MOVE
CHANGE
Press the CLEAR button to return to normal
playback.
Press the œ √ button to select A-B, then press the
ENTER button.
Press the ENTER button at the point where you want
the repeat play to start (A) and press it again at the
point where you want the repeat play to stop (B).
Repeat playback of the A-B section starts.
Repeat A-B
A-B

 If you set point (B) before five seconds has
Note
lapsed, the prohibition mark (
) will appear.

 You can also activate Normal Playback by
pressing the CLEAR button.

 CDs do not support the Repeat A-B function.
- To return to normal playback -
40 - English
Press the CLEAR button to return to normal
playback.
00588A(00)-VR320-2/XAA-eng
6/7/05
7:14 PM
Page 41
Selecting the Subtitle &
Audio Language
Press the …† buttons to select Subtitle, then
press the œ √ buttons to select the desired subtitle language.
DVD-VIDEO
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Off
(VR mode)
1/1
Off
Selecting the SUBTITLE language
MOVE
CHANGE
Subtitle languages may not work depending on the
disc type. This is only available during playback.

 The subtitle display may be different dependNote
Using the SUBTITLE button
function on your TV.

 Some discs allow you to select the language
Press the SUBTITLE button during playback.
Subtitle
ing on the disc type.

 If the subtitles overlap, disable the caption
for the disc menu only.
ENG
Selecting the Audio language
Audio languages may not work depending on the
disc type. This is only available during playback.
Press the …† buttons to select the desired subtitle language.
• To make the screen disappear, then press the
CLEAR or RETURN button.
Press the ANYKEY button during playback.
DVD-VIDEO
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Title
1/1
Off
MOVE
CHANGE
Using the ANYKEY button
Press the ANYKEY button during playback.
Press the …† buttons to select Audio, then press
the œ √ buttons to select the desired audio language.
DVD-VIDEO
1/10
DVD-VIDEO
1/40
1/10
00:01:45
1/40
Off
ENG
MOVE
00:01:45
D 5.1CH
Off
Title
ENG
1/1
Off
Off
1/1
CHANGE
D 5.1CH
Off
MOVE
CHANGE

 Audio languages may be different because
Note
they are disc-specific.

 Some discs allow you to select the audio
language for the disc menu only.
English - 41
Playback
00588A(00)-VR320-2/XAA-eng
6/7/05
7:14 PM
Page 42
Changing the Camera
Angle
When a DVD Recorder & VCR contains multiple angles
of a particular scene, you can select the Angle function.
Zooming-In
Press the ANYKEY button during playback.
DVD-VIDEO
Using the ANGLE button
1/10
1/40
00:01:45
If the disc contains multiple angles, the ANGLE
appears on the screen.
Off
ENG
D 5.1CH
Off
1/1
Playback
Off
Press the ANGLE button, then the ANGLE icon
will appear with the current angle number and the
number of angles available.
Press the …† button to select the desired angle.
MOVE
CHANGE
Press the …† buttons to select Zoom, then press
the ENTER button. ( ) will be displayed.
Press …†, œ √ buttons to move to the area you
want to enlarge.
Press the ENTER button.
The screen will be enlarged to twice the normal
size. The screen size will be enlarged to four
times the normal size.
Using the ANYKEY button
Press the ANYKEY button during playback.
DVD-VIDEO
1/10
1/40
00:01:45
Off
ENG
D 5.1CH
Off
1/3
Off
MOVE
CHANGE
Press the …† buttons to select Angle, then press
the œ √ buttons or number (0~9) buttons to select
the desired angle scene.
DVD-VIDEO/
DVD-RAM/DVD-RW/
DVD-R
DVD-VIDEO
1/10
1/40
00:01:45
normal size ➝ 2X ➝ 4X ➝ 2X
➝ normal size
Off
ENG
D 5.1CH
Off
1/3

 When recording is done in the EP mode, the
Off
MOVE
CHANGE
Note

 This function is disc-dependent, and may not
Note
work all DVDs.

 This function does not work when a DVD has
not been recorded with a multi-camera angle
system.
42 - English
Zoom function will not be supported.
(except when the recording has been done
in V mode)
00588A(00)-VR320-2/XAA-eng
6/7/05
7:14 PM
Page 43
Using the Bookmarks
Playing back a Bookmark
Press the MARKER button.
Press the œ √ buttons to select a bookmarked
scene.
(V-mode)
Bookmark 1 2
Set marks at scenes you want to see again so that you
can start playback from the marked position.
Press the MARKER button during playback.
MOVE
PLAY
CANCEL
RETURN
Bookmark
MOVE
SELECT
Press the ENTER or √ll button to start playing
from the selected scene.
RETURN
Clearing a Bookmark
Press the ENTER button when the desired scene
appears.
• The number 1 is displayed and the scene is
memorized.
Bookmark
Press the MARKER button.
Press the œ √ buttons to select a bookmarked
scene.
Bookmark 1 2
MOVE
PLAY
CANCEL
RETURN
MOVE
Press the œ √ button to move to the next position.
Press the ENTER button again when the desired
scene appears.
• The number 2 is displayed and the scene is memorized. Repeat above to bookmark other positions.
You can bookmark up to 10 scenes.
Bookmark
CANCEL
RETURN
Press the CLEAR button to delete the selected
bookmark.
Bookmark 1
1 2
MOVE
MOVE
PLAY
PLAY
CANCEL
SELECT
RETURN
RETURN
English - 43
Playback
00588A(00)-VR320-2/XAA-eng
6/7/05
7:14 PM
Page 44
Playing back a Marker
Using the Markers
Press the MARKER button during playback.
Press the œ √ buttons to select a marked scene.
Marker
(VR mode)
N:0
Marker
SELECT
Press the ENTER button when the desired scene
appears.
Marker
01
PLAY
CANCEL
RETURN
RETURN
Playback
N:2
Press the MARKER button during playback.
MOVE
01 02
N:1
Press the ENTER or √l l button to start playing
from the selected scene.
• If you press the NEXT SKIP (√√l )button or the
PREVIOUS SKIP(lœœ)button in marker mode,
and the next or current marked point plays for
shorter than three seconds, playback starts from
the previous marked point.
Clearing a Marker
MOVE
PLAY
CANCEL
RETURN
• The number 01 is displayed and the scene is
memorized.
Press the œ √ button to move to the next position.
Press the ENTER button again when the desired
scene appears.
Marker
MOVE
01 02
PLAY
Press the MARKER button during playback.
Press the œ √ buttons to select a marked scene.
Press the CLEAR button to delete the selected
mark.
Marker
01 02 03 04 05 06 07 08 09 10
Marker
01 02 03 04 05 06 07 08 09
√ N:10
N:2
CANCEL
N:9
RETURN
• The number 02 is displayed and the scene is
memorized.
• DVD-RAM or DVD-RW (VR Mode) discs have
the Marker function instead of the Bookmark
function. The Marker function allows you to mark
up to 99 scenes. Since the scenes may be displayed as many different pages, numbering is
necessary. If a disc in use is encoded with Disc
Protect, Markers cannot be set or deleted. Only
playback is available.
44 - English
MOVE
PLAY
CANCEL
RETURN
• When a marker is cleared while DVD-RAM/
DVD-RW(VR mode) is playing, marker numbers
will change. For example, if the 7th marker is
cleared after ten markers are registered, the
marker numbers after the eighth will automatically move ahead by one and the 8th marker
becomes the 7th.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2005:07:19 17:14:54-03:00
Create Date                     : 2005:07:19 17:13:54-03:00
Title                           : 00588A(00)-VR320-1/XAA-eng
Author                          : sul
Creator                         : QuarkXPress.: AdobePS 8.8.0 (301)
Producer                        : Acrobat Distiller 5.00 for Macintosh
Page Count                      : 44
Mod Date                        : 2005:07:19 17:14:54-03:00
Creation Date                   : 2005:07:19 17:13:54-03:00
Metadata Date                   : 2005:07:19 17:14:54-03:00

EXIF Metadata provided by EXIF.tools