Samsung Electronics Co HPN4235 42-inch PDP Monitor User Manual 2
Samsung Electronics Co Ltd 42-inch PDP Monitor Users Manual 2
Contents
- 1. Users Manual 1
- 2. Users Manual 2
Users Manual 2
Turning the PDP On and Off Turning the PDP On and Off Displaying Status Information Press the INFO button on the remote control. The PDP will display the Picture mode, Sound mode, MTS, Signal and Caption. Press the INFO button on the remote control again. The PDP will display the Clock. Press the Power button on the remote control. The PDP will be turned on and you will be ready to use it’s features. You can also use the POWER( ) button on the front of the PDP. Ant 6 Picture Sound MTS Signal Caption Custom Custom Mono Mono Off Notes: • If your PDP isn’t turned on when the power button is pressed: Press the MODE button to check if the TV mode has been chosen ( ). 07 : 30 am Viewing the Menus and Displays Your PDP has a simple, easy-to-use menu system that appears on the PDP screen. This system makes it convenient and fast to use features on the PDP. Your PDP also lets you display the status of many of your PDP’s features. Viewing the Menus With the power on, press the MENU button on the remote control. The main menu appears on the screen. The Picture menu is selected. Picture Mode Adjust Color Tone DNIe Move 30 Custom Normal On Enter Menu Press the UP/DOWN buttons to move items in the menu. Press the LEFT/RIGHT buttons to display, change, or use the selected items. Press the ENTER ( ) button to enter items in the menu. On screen menus disappear from the screen automatically after about thirty seconds, or you can press the EXIT button on your remote control to exit the menu. 31 Memorizing the Channels Your PDP can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual). Selecting the Video Signal-source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the PDP (i.e., an antenna or a cable system). Press the MENU button. Press the UP or DOWN button to select “Channel”, then press the ENTER button. Press the LEFT or RIGHT button to select “Ant”, “STD”, “HRC” or “IRC”. • If you are connected to an antenna, leave "Ant" displayed. If you connected cable, press the LEFT or RIGHT button to the display the type of cable system: "STD", "HRC", or "IRC". (If you are not sure which type of cable system you have, contact your cable company). First, select the correct signal source (Ant, STD, HRC, IRC). See steps on previous page. Press the MENU button. Press the UP or DOWN button to select “Channel”, then press the ENTER button. Channel Ant/ CATV Auto Program Fine Tune LNA Ch. Scan Ant Off ➤ Quick way to access the Automatic Channel Setting : Just press the “AUTO PROG.” button on the remote control. Channel Ant/ CATV Auto Program Fine Tune LNA Ch. Scan Move Storing Channels in Memory (Automatic Method) Off Select Press the UP or DOWN button to select “Auto Program”, then press the ENTER button. Menu Channel Ant/ CATV Auto Program Fine Tune LNA Ch. Scan Move Move Select Menu Ant Channel Ant / CATV Auto Program Fine Tune LNA Ch. Scan Move Ant Off Enter Menu STD Off Select Menu The PDP will begin memorizing all of the available channels. After all the available channels are stored, the Auto program menu reappears. Press the RIGHT button to stop. Ant 50 Auto Program : Stop Press the MENU button to exit. Note • The PDP automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes. Note • STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page). 32 33 Adding and Erasing Channels (Manual Method) Use the number buttons to directly select the channel that will be added or erased. To View Memorized Channel (PIP Mode) Ant 4 Press the MENU button. Press the UP or DOWN button to select “Channel”, then press the ENTER button. Channel Ant/ CATV Auto Program Fine Tune LNA Ch. Scan Ex) Channel “4” Move Press the ADD/DEL button: Repeatedly pressing this button will alternate between “Added” and “Erased.” Press the UP or DOWN button to select “Ch Scan”, then press the ENTER button. Only the memorized channels are chosen. Press the RIGHT button to stop. Off Select Menu Channel Ant / CATV Auto Program Fine Tune LNA Ch. Scan Move Ant 4 Added Ant Ant Off Enter Menu Ch. Scan Ant 7 : Stop Note • You can view any channel (including an erased channel) by using the number buttons on the remote control. 34 35 Setting Up Your Remote Control This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up properly, your remote control can operate in four different modes :TV, VCR, Cable or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Changing Channels Using the Channel Buttons Press the CH or CH Note : buttons to change channels. ● ● When you press the CH or CH buttons, the PDP changes channels in sequence. You will see all the channels that the PDP has memorized. (The PDP must have memorized at least three channels.) You will not see channels that were either erased or not memorized. The remote control may not be compatible with all DVD Players, VCRs, Cable boxes. The remote control can operate only on STB made by Samsung. Setting Up the Remote to Operate Your VCR, Cable box or DVD player Directly Accessing Channels Press the number buttons to go directly to a channel. For example, to select channel 27, press “2” then “7”. The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To change to single-digit channels (0~9) faster, press “0” before the single digit. (For channel “4” press “0”, then “4”. Using the Pre-CH button to select the previous channel Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. Adjusting the Volume Turn off your VCR. (or Cable box, DVD player) Press the MODE button. Mode is changed whenever MODE button is pressed(New mode is displayed on LED screen). Press the SET button on your TV's remote control. Using the number buttons on your remote control, enter three digits of the VCR (or Cable box, DVD player) code listed on page 38 of this manual for your brand of VCR (or CATV, DVD). Make sure you enter three digits of the code, even if the first digit is a "0". (If more than one code is listed, try the first one.) Press the Power button on the remote control. Your VCR (or CATV, DVD) should turn on if your remote is set up correctly. If your VCR (or CATV, DVD) does not turn on after setup, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR (or CATV, DVD). If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008). Using the Volume Buttons Press the VOL + or VOL – buttons to increase or decrease the volume. Using Mute Using the MUTE Buttons At any time, you can temporarily cut off the sound using the MUTE button. Press the MUTE button and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen. Notes • When your remote control is in “VCR” mode, the VCR control buttons (Stop, REW, Play/Pause, FF) still operate your VCR. 36 To turn mute off, press the MUTE button again, or simply press the VOL + or VOL – button. Mute • When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (Stop, REW, Play/Pause, FF) still operate your VCR. 37 Remote Control Codes VCR Codes Cable Box Codes Picture Control Customizing the Picture ................................................................40 Using Automatic Picture Settings ....................................................41 Selecting the Color Tone................................................................42 DNIe (Digital Natural Image engine) ............................................43 Viewing the Picture-in-Picture..........................................................44 Changing the Screen Size ............................................................50 Freezing the Picture ......................................................................51 DVD Codes 38 1 Customizing the Picture Using Automatic Picture Settings You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color, and Tint settings of your PDP. Your PDP has automatic picture settings that allow you to adjust the video display easily. Press the MENU button, then press the ENTER button. Picture Mode Adjust Color Tone DNIe Custom Custom On Press the MENU button, then press the ENTER button. ➤ Quick way to access the picture setting: Just press the “P.MODE” Picture Mode Adjust Color Tone DNIe Custom Custom On button under the cover of the remote control. Move Press the UP or DOWN button to select “Adjust”, then press the ENTER button. You will also see the items “Contrast”, “Brightness”, “Sharpness”, “Color” and “Tint”. Press the UP or DOWN button to select the item you wish to change. Normal On Enter Adjust Press the LEFT or RIGHT button to select “Custom”, “Dynamic”, “Standard” or “Movie” picture setting. • You can select “High”, “Middle”, “Low” or “Custom” in PC/DVI mode. 80 50 50 50 G 50 Select Menu Picture Mode Adjust Color Tone DNIe Move Menu Adjust Dynamic Custom On Select Menu Press the MENU button to exit. Menu Press the LEFT or RIGHT button to change the value of the item. Contrast Move Custom Contrast Brightness Sharpness Color Tint R 50 Move Menu Picture Mode Adjust Color Tone DNIe Move Select 82 Press the MENU button to exit. Note • In the PC/DVI mode, you can’t adjust the Color and Tint. 40 41 Selecting the Color Tone DNIe (Digital Natural Image engine) Samsung’ s New Technology brings you more detailed images with contrast and white enhancement and 3D noise reduction. Press the MENU button, then press the ENTER button. Picture Mode Adjust Color Tone DNIe Move Press the UP or DOWN button to select “Color Tone”, then press the LEFT or RIGHT button to select “Normal”, “Warm1”, “Warm2”, “Cool2” or “Cool1”. • You can select “Custom”, “Color1”, “Color2” or “Color3” in PC mode. • You can select “Color1”, “Color2” or “Color3” in DVI mode. Custom Select Move Press the MENU button, then press the ENTER button. ➤ Quick way to select DNIe : Simply press the “DNIe” button under Custom On the cover of the remote control. Menu Picture Mode Adjust Color Tone DNIe Custom Move Press the UP or DOWN button to select “DNIe”, then press the LEFT or RIGHT button to select “On”, “Off” or “Demo”. Normal On Select • On : Switches on the DNIe mode. • Demo : The screen before applying DNIe appears on the right and the screen after applying DNIe appears on the left. • Off : Switches off the DNIe mode. Menu Press the MENU button to exit. Custom Custom On Select Menu Picture Mode Adjust Color Tone DNIe Move Custom Normal On Select Menu DNIe Demo DNIe On 42 Picture Mode Adjust Color Tone DNIe DNIe Off Press the MENU button to exit. 43 Viewing the Picture-in-Picture Selecting the PIP Screen Selecting an External Signal You can use PIP to view a signal from an external source, such as a VCR. Press the MENU button. Press the UP or DOWN button to select “PIP”, then press the ENTER button. PIP Select Off ➤ Quick way to access the PIP mode: Just press the “PIP” button on Press the MENU button. Press the UP or DOWN button to select “PIP”, then press the ENTER button. the remote control. Select Menu PIP Select Source Swap Size Locate Ant/CATV Channel Move Press the LEFT or RIGHT button to select “On”. The PIP image will appear in the corner of the screen. • Pressing the LEFT or RIGHT button will alternate between “On” and “Off.” PIP Select Source Swap Size Locate Ant/CATV Channel Move On TV Ant Ant 5 Menu Press the MENU button to exit. O : PIP and Swap Operate X : PIP doesn’t Operate PIP Settings PIP screen Main screen TV Video S-Video Component 1 Component 2 PC DVI 44 TV Video S-Video Component 1 Component 2 PC DVI Press the LEFT or RIGHT button to cycle through all of the available signal sources: “TV”, “Video”, “S-Video”, “Component 1”, “Component 2”, “PC” and “DVI”. The signal from these inputs will not appear if you have not connected any equipment to the PDP's respective input jacks. Ant Ant 5 Select Menu PIP Select Source Swap Size Locate Ant/CATV Channel Move Large Press the UP or DOWN button to select “Source”. Large Select On TV On TV Large Ant Ant 5 Select Menu PIP Select Source Swap Size Locate Move On Video Large Select Menu Press the MENU button to exit. Note • The PIP function operates in Wide screen. • Using Multi-Screen in the Normal, Zoom1 or Zoom2 screen will change the size of the main screen to Wide screen. 45 Swapping the Contents of the PIP Image and Main Image Press the MENU button. Press the UP or DOWN button to select “PIP”, then press the ENTER button. ➤ Quick way to access swapping: Just press the “SWAP” button under the cover of the remote control. Press the UP or DOWN button to select “Swap”, then press the ENTER button. • The image in the PIP window will appear on the main screen, and vice versa. Press the MENU button to exit. On TV Press the MENU button. Press the UP or DOWN button to select “PIP”, then press the ENTER button. ➤ Quick way to access the PIP size: Just press the “SIZE” button Large under the cover of the remote control. Ant Ant 5 Select Menu On TV Press the LEFT or RIGHT button to select “Small”, “Double” or “Large”. Menu On TV Large Ant Ant 5 Select Menu PIP Select Source Swap Size Locate Ant/CATV Channel Move 46 Ant Ant 5 Select PIP Move Menu Large Select Source Swap Size Locate Ant/CATV Channel Ant Ant 5 On TV Press the UP or DOWN button to select “Size”. Large Enter PIP Select Source Swap Size Locate Ant/CATV Channel Move PIP Select Source Swap Size Locate Ant/CATV Channel Move PIP Select Source Swap Size Locate Ant/CATV Channel Move Changing the Size of the PIP Window On TV Small Ant Ant 5 Select Menu Press the MENU button to exit. 47 Changing the Location of the PIP Image Press the MENU button. Press the UP or DOWN button to select “PIP”, then press the ENTER button. Changing the PIP Channel Move Press the LEFT or RIGHT button to move the PIP screen where you want. 48 Press the MENU button to exit. “CH▼” button under the cover of the remote control. Ant Ant 5 Select Press the MENU button. Press the UP or DOWN button to select “PIP”, then press the ENTER button. ➤ Quick way to change the PIP channel: Just press the “CH▲“ or Large Menu On TV Press the UP or DOWN button to select “Ant/CATV”. Press the LEFT or RIGHT button to select “Ant”, “STD”, “HRD” or “IRC”. Large Ant Ant 5 Select On TV Press the UP or DOWN button to select “Channel”. Press the LEFT or RIGHT button to change the channel that appears in the PIP window. Large Ant Ant 5 Select Large Ant Ant 5 Select Menu PIP On TV Large STD STD 5 Select Menu PIP Select Source Swap Size Locate Ant/CATV Channel Move Menu On TV Select Source Swap Size Locate Ant/CATV Channel Move Menu PIP Select Source Swap Size Locate Ant/CATV Channel PIP Select Source Swap Size Locate Ant/CATV Channel Move PIP Select Source Swap Size Locate Ant/CATV Channel Move On TV Press the UP or DOWN button to select “Locate”. Move PIP Select Source Swap Size Locate Ant/CATV Channel On TV Large STD STD 9 Select Menu Press the MENU button to exit. 49 Changing the Screen Size When you press the ASPECT button on the remote control, the PDP’s screen mode should appear in sequence. The screen displays in this order: Wide, Panorama, Zoom1, Zoom2, Normal. Note Changing the Screen Size Still Press the Still button on the remote control to freeze a moving picture. Press again to cancel. • If you watch a still image or the Normal (4:3) mode for a long time (over 2 hours), an image may be burned onto the screen. View the monitor in Wide or Panorama mode as much as possible. W ide Zoom2 Sets the picture to 16:9 wide mode. The screen size when the Zoom1 screen is vertically enlarged. Wide Zoom2 Up/Down Panorama Normal (4:3) Converts regular 4:3 aspect ratio screen to wide screen. Sets the picture to 4:3 normal mode. Panorama Normal Zoom1 The screen size when Wide screen is vertically enlarged. Zoom1 Up/Down Notes 50 • In TV, VIDEO, S-VIDEO and Component(480i) modes, all screen modes can be selected. (Wide ➝ Panorama ➝ Zoom1 ➝ Zoom2 ➝ Normal). • In PC/DVI mode, only Wide & Normal modes can be selected. • In Component(480p, 720p. 1080i) modes, Panorama mode can’t be selected. • In Component(480p, 720p. 1080i) modes, you can move the picture on screen by pressing the Up▲ or Down▼ button. (All screen modes) • Changing the screen size to Normal, Zoom1 or Zoom2 during PIP mode will cause the PIP window to disappear. 51 P Sound Control Customizing the Sound ................................................................54 Using Automatic Sound Settings ....................................................55 Choosing a Multi-Channel Sound (MTS)Soundtrack ..........................56 Using the Auto Volume ..................................................................57 Using Dolby Virtual ......................................................................58 Using a Subwoofer ......................................................................59 Customizing the Sound Press the MENU button. Press the UP or DOWN button to select “Sound”, then press the ENTER button. Press the UP or DOWN button to select “Adjust”, then press the ENTER button. You will also see the items “Bass”, “Treble” and “Balance”. Press the UP or DOWN button to select the item you wish to change. 54 Select Menu Move Custom Press the LEFT or RIGHT button to select “Adjust”, “Standard”, “Music”, “Movie” or “Speech” sound setting. Mono Off Off Enter L 50 Adjust Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer 50 50 R 50 Mono Off Off Select Menu Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Menu Custom Music Off Off Select Menu Press the MENU button to exit. Menu Press the LEFT or RIGHT button to change the value of the item. Bass Off Off Adjust Bass Treble Balance Press the MENU button. Press the UP or DOWN button to select “Sound”, then press the ENTER button. Mono Sound Move Custom Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Using Automatic Sound Settings 82 Press the MENU button to exit. 55 Choosing a Multi-Channel Sound (MTS) Soundtrack Using the Auto Volume Each broadcasting station has its own signal conditions, which can make it necessary to adjust the volume every time the channel is changed. “Auto volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low. Depending on the particular program being broadcast, you can listen to stereo, mono, or a Separate Audio Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated information like news or weather.) Press the MENU button. Press the UP or DOWN button to select “Sound”, then press the ENTER button. ➤ Quick way to access the MTS menu: Just press the “MTS” button on the remote control. Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Press the LEFT or RIGHT button to select “Mono”, “Stereo” or “SAP”. Select Menu Standard Move Press the UP or DOWN button to select “Auto Volume”. Off Off Select Stereo Off Off Select Press the LEFT or RIGHT button to select “On”. • Pressing the LEFT or RIGHT button will alternate between “On” and “Off.” Menu Press the MENU button to exit. • Choose Stereo for channels that are broadcasting in stereo. • Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving a stereo signal. • Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation. Mono Off Off Select Menu Standard Mono Off Off Select Menu Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Custom Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Menu Standard Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Mono Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Press the MENU button. Press the UP or DOWN button to select “Sound”, then press the ENTER button. Off Off Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Mono Press the UP or DOWN button to select “MTS”. Move Custom Standard Mono On Off Select Menu Press the MENU button to exit. Note • The MTS function operates in TV mode only. 56 57 Using Dolby Virtual Using a Subwoofer This feature allows the PDP’s optional L/R speakers to provide a Home Theater-like Dolby effect. The center and surround sounds are mixed into the L/R speakers. Press the MENU button. Press the UP or DOWN button to select “Sound”, then press the ENTER button. ➤ Quick way to access the Surround: Just press the “SURROUND” button on the remote control. Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Press the UP or DOWN button to select “Dolby Virtual”. Mode Adjust MTS Auto Volume Dolby Virtual Woofer Press the LEFT or RIGHT button to select “On”. • Pressing the LEFT or RIGHT button will alternate between “On” and “Off.” Mono Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Off Off Select Move Menu Press the UP or DOWN button to select “Woofer”, then press the ENTER button. Standard Custom Mono Off Off Select Menu Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Mono Move Standard Mono Off Off Enter Menu Off Off Select Menu Press the LEFT or RIGHT button to select “On”. • Pressing the LEFT or RIGHT button will alternate between “On” and “Off.” Woofer Woofer Volume Cutoff Freq. On 50 120Hz Sound Mode Adjust MTS Auto Volume Dolby Virtual Woofer Move Custom Sound Move Press the MENU button. Press the UP or DOWN button to select “Sound”, then press the ENTER button. Standard Move Select Menu Mono Off On Select Menu Press the UP or DOWN button to select “Volume”, then press the LEFT or RIGHT button to adjust the value of the item. This sets the volume for the subwoofer. Woofer Woofer Volume Cutoff Freq. On 50 120Hz Press the MENU button to exit. Move Adjust Menu Volume 58 Press the UP or DOWN button to select “Cutoff Freq.”, then press the LEFT or RIGHT button to adjust the value of the item. This sets the cutoff frequency for the subwoofer. For example, if you set the cutoff frequency at 130Hz, the subwoofer will reproduce frequencies of 130Hz and lower. 65 Woofer Woofer Volume Cutoff Freq. Move On 50 130Hz Adjust Menu Press the MENU button to exit. 59 P Channel Control Fine Tuning Channels....................................................................62 LNA (Low Noise Amplifier) ............................................................63 1 Fine Tuning Channels LNA (Low Noise Amplifier) Use fine tuning to manually adjust a particular channel for optimal reception. If the TV is operating in a weak-signal area, sometimes the LNA function can improve the reception (a low-noise preamplifier boosts the incoming signal). Press the MENU button. Press the UP or DOWN button to select “Channel”, then press the ENTER button. Channel Ant/ CATV Auto Program Fine Tune LNA Ch. Scan Move Press the UP or DOWN button to select “Fine Tune”. Press the LEFT or RIGHT button to adjust the fine tuning. To store the fine tuning setting in the TV’s memory, press the UP button.(A star icon<*>will appear.) To reset the fine tuning to “0”, press the DOWN button. 62 Press the MENU button. Press the UP or DOWN button to select “Channel”, then press the ENTER button. Menu Air Press the UP or DOWN button to select “LNA”. Menu Channel Air +3 Off Adjust Press the LEFT or RIGHT button to select “On.” • Pressing the LEFT or RIGHT button will alternate between “On” and “Off.” Menu Channel Air / CATV Auto Program Fine Tune LNA Ch. Scan Air Select Menu Air Off Select Menu Channel Air / CATV Auto Program Fine Tune LNA Ch. Scan Move Off Channel Move Ant Air / CATV Auto Program Fine Tune LNA Ch. Scan Off Adjust Channel Ant/ CATV Auto Program Fine Tune LNA Ch. Scan Move Air / CATV Auto Program Fine Tune LNA Ch. Scan Add/Erase Select Channel Add/Erase Off Air / CATV Auto Program Fine Tune LNA Ch. Scan Move Ant Air On Select Menu Press the MENU button to exit. +3 Off Adjust Menu Press the MENU button to exit. 63 P Connecting a PC and Operation Connecting to a PC ......................................................................66 Adjusting the PC Screen................................................................70 Changing the Position of the Image................................................71 Changing the Size of the Image ....................................................72 Information ..................................................................................73 Picture Quality Adjustment ............................................................74 Connecting to a PC Connection to a Macintosh computer may require in adapter. PDP Pin Configuration D-Sub Cable DVI-D Cable (Digital-Only Connector) • 15Pin Signal Cable (based on protruded pin) Power Plug Use the DVI-D connection cable. (sold separately) DVI Cable Ferrite Cores or PC Cable Audio Cable PC DVI jack (The actual configuration on your PC may be different, depending on the model.) Setting up Your PDP (Plug and Play) Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual setup hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification data (EDID) using Display Data Channel (DDC) protocols. Connecting a PC to the PDP Connect a PC (15pin) cable between the PC Output jack (or DVI jack) on the PC and the RGB IN(or DVI IN) Input jack (15p D-SUB) on the PDP. Connect a Audio cable between the Audio (RGB or DVI) on the PC and the Audio L/R (RGB or DVI) input jacks on the PDP. To watch the PC screen: 1. Turn on your PDP, and press the TV/VIDEO button on the remote control. 2. Press the UP or DOWN button to select “PC”, then press the ENTER button. 3. Turn on PC and check for PC system requirements. (Refer to pages 66 and 67 for PC system requirements.) 4. Adjust the PC screen. (Refer to pages 70 and 76.) 66 67 How to Set up Your PC Software (Windows only) The Windows display-settings for a typical computer are shown below. However, the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.) Notes: Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Video signal On the windows screen, select in the following sequence : Start ➝ Settings ➝ Control Panel. Dot X Line Vertical Frequency (Hz) Horizontal Frequency (KHz) Vertical polarity Horizontal polarity 640 X 350 70.086 31.469 85.080 37.861 640 X 400 85.080 37.861 720 X 400 70.087 31.469 85.039 37.927 59.940 31.469 72.809 37.861 75.000 37.500 85.008 43.269 56.250 35.156 N/P N/P 60.317 37.879 72.188 48.077 75.000 46.875 85.061 53.674 60.004 48.363 70.069 56.476 75.029 60.023 84.997 68.677 640 X 480 IBM PC / AT Compatible 800 X 600 When the control panel screen appears, click on “Display” and a display dialog-box will appear. 1024 X 768 Select the “Settings” tab in the display dialogbox. The two key variables that apply to the PDP-PC interface are “resolution” and “colors”. The correct settings for these two variables are: • The PDP operates abnormally if a non-standard video format is selected. • Size (sometimes called “resolution”) :640 x 480 pixels. Notes: • Color: “24-bit” color (might also be expressed as “16 million colors”)Shown at left is a typical screen for “Display” dialog box. • Depending on the manufacturer, your PC display screen might appear different. (and depending on your particular version of Windows). If a vertical-frequency option exists on your display settings dialog box, the correct value is “60” or “60 Hz.” Otherwise, just click “OK” and exit the dialog box. Continued... 68 • The interlace mode is not supported. • When this PDP is used as a PC display, 32-bit color is supported. Check your PC instruction book for information about connecting your PC to a PDP. • If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHZ (horizontal). • In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the Source button to enter the VIDEO mode. Also, make sure that the PC is connected. • Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, random signals might appear). 69 Adjusting the PC Screen Changing the Position of the Image Adjusting the R.G.B After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned. Preset: • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. Preset: • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. Press the MENU button, then press the ENTER button. Picture Mode Adjust Color Tone Color Adjust DNIe Move Press the MENU button. Press the UP or DOWN button to select “PC”, then press the ENTER button. Press the UP or DOWN button to select “Color Tone”, then Press the LEFT or RIGHT button to select “Custom”. When “Custom” is selected, the word “Color Adjust” will appear on the screen. Custom PC Position Adjust Scaling Information Auto Adjust Custom Move On Select Mode Adjust Color Tone Color Adjust DNIe Press the MENU button, then adjust the screen position by using the UP/DOWN/LEFT/RIGHT button. Press the UP or DOWN button to select “Color Adjust”, then press the ENTER button. Custom Custom On Press the UP or DOWN button to select the item you want to change, then press the RIGHT or LEFT button to change the value of the item, using the on-screen gauge as your guide. Custom Menu Press the MENU button to exit. Custom On Enter Menu Adjust Red Green Blue Red 70 Move Menu Picture Move Select Mode Adjust Color Tone Color Adjust DNIe Move Menu Position Move Enter Menu Picture Move Wide 50 50 50 Adjust Menu 82 Press the MENU button to exit. 71 Changing the Size of the Image Information Preset: Preset: • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. Press the MENU button. Press the UP or DOWN button to select “PC”, then press the ENTER button. Move Enter PC Wide Select PC Position Adjust Scaling Information Auto Adjust Move Menu Position Adjust Scaling Information Auto Adjust Move Press the MENU button. Press the UP or DOWN button to select “PC”, then press the ENTER button. Wide Press the UP or DOWN button to select “Scaling”. Press the LEFT or RIGHT button to select “Wide” or “Normal”. PC Position Adjust Scaling Information Auto Adjust Press the UP or DOWN button to select “Information”, then press the ENTER button. The vertical, horizontal frequencies and resolution appear. Menu Wide Enter Menu PC Position Adjust Scaling Information Auto Adjust Move Wide Enter Menu Information PC Position Adjust Scaling Information Auto Adjust Resolution H-Frequency V-Frequency Normal 1024 * 768 48.52 KHz 60.21 Hz Menu Move 72 Press the MENU button to exit. Select Menu Press the MENU button to exit. 73 Picture Quality Adjustment Picture Automatic Adjustment Coarse Adjustment Preset: Preset: • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. Press the MENU button. Press the UP or DOWN button to select “PC”, then press the ENTER button. Move Press the UP or DOWN button to select “Auto Adjust”, then press the ENTER button. Press the MENU button. Press the UP or DOWN button to select “PC”, then press the ENTER button. PC Position Adjust Scaling Information Auto Adjust Wide Enter Menu Move PC Position Adjust Scaling Information Auto Adjust Move PC Position Adjust Scaling Information Auto Adjust Press the UP or DOWN button to select “Adjust”, then press the ENTER button. The message “Auto Adjust” appears on the screen and the picture adjustments are automatically activated. Move Auto Adjust Enter Menu Adjust 50 Corase Fine Remove picture noise (vertical stripes) on the screen by pressing the LEFT or RIGHT button. (If Coarse is not set properly, vertical stripes will appear on the screen.) Adjust Menu Press the MENU button to exit. Coarse 74 Wide Press the UP or DOWN button to select “Coarse”. Move Menu PC Menu Enter Position Adjust Scaling Information Auto Adjust Wide Enter Wide 53 Press the MENU button to exit. 75 Fine Tuning (Fine) Preset: • Press the TV/VIDEO button, then press the UP or DOWN button to select PC. Press the ENTER button to select PC mode. Press the MENU button. Press the UP or DOWN button to select “PC”, then press the ENTER button. PC Position Adjust Scaling Information Auto Adjust Move Press the UP or DOWN button to select “Adjust”, then press the ENTER button. Wide Enter Menu PC Position Adjust Scaling Information Auto Adjust Move Wide Enter Menu Press the UP or DOWN button to select “Fine”. Adjust 50 Corase Fine Remove picture noise on the screen by pressing the LEFT or RIGHT button. (If Fine is not set properly, noise will appear on the screen.) Time Setting Move Adjust Menu Setting the Clock .......................................................................78 Setting the Sleep Timer...............................................................79 Setting the Timers ......................................................................80 Fine 76 Press the MENU button to exit. 53 Setting the Preferred Channel and Volume Level ............................82 Setting the Clock Setting the Sleep Timer You can set your PDP to automatically turn off after a preset interval. Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Move Press the UP or DOWN button to select “Time”, then press the ENTER button. Press the LEFT or RIGHT button to select hour, then press the UP or DOWN button to select the correct hour. Press the LEFT or RIGHT button to select minute, then press the UP or DOWN button to select the correct minute. on the remote control. Off Select Menu Press the UP or DOWN button to select “Time”, then press the ENTER button. Off Off Off Enter Menu Time 10 : - - am - - : - - am - - : - - am Move Off Off Off 10 10 : 30 am - - : - - am - - : - - am Move Off Off Off 10 Menu English Off Off Off Enter Menu Time Clock 10 : 30 am On Time - - : - - am Off Time - - : - - am Sleep On Time Volume On Time Channel Press the LEFT or RIGHT button to select the time interval for the PDP to stay on. The interval ranges from 10 to 180 minutes. Select Off Off Off 10 Menu Time Clock 10 : 30 am On Time - - : - - am Off Time - - : - - am Sleep On Time Volume On Time Channel Move Off Select Press the UP or DOWN button to select “Sleep”. Menu Press the MENU button to exit. Off Off Function Move English Language Time Caption NR Auto Power Off V-Chip Film Mode Move Menu Time Clock On Time Off Time Sleep On Time Volume On time Channel Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Clock On Time Off Time Sleep On Time Volume On time Channel Adjust Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. ➤ Quick way to access the sleep timer: Just press the “SLEEP” button Off Off Function Adjust English Language Time Caption NR Auto Power Off V-Chip Film Mode Move Function Language Time Caption NR Auto Power Off V-Chip Film Mode Select Off Off 30 10 Menu Press the MENU button to exit. Note • Time setting will be reset when you pull out the Power cord if the PDP is ON. (If you want to keep the time setting, turn the PDP off using the POWER button on the remote control or the Front Panel.) 78 79 Setting the Timers This PDP can be set to turn on or off automatically at specific times that you choose. Before using the timers, you must set the PDP’s clock, as described previously. Setting the On/Off Timer Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the UP or DOWN button to select “Time”, then press the ENTER button. Press the LEFT or RIGHT button to select minute, then press the UP or DOWN button to select the correct minute. If you want to set Off Time, press the UP or DOWN button to select the “Off Time”. Set the “Off Time” just as you set “On Time”. Off Off 10 : 30 am 7 : 30 am - - : - - am On Off Off 10 Move Menu Time Clock 12 : 00 am On Time 7 : 30 am Off Time - - : - - am Sleep On Time Volume On Time Channel On Off Off 10 Off Enter Move Menu Time 10 : 30 am - - : - - am - - : - - am Select Off Off Off 10 Menu Select Menu Press the MENU button to exit. Note • If you set to On Time or Off Time, the Power Indicator on the Front Panel is changed to Green. Time Clock On Time Off Time Sleep On Time Volume On time Channel 10 : 30 am 7 : - - am - - : - - am Move Off Off Off 10 Menu Time Clock On Time Off Time Sleep On Time Volume On time Channel Adjust 80 Adjust Menu English Clock On Time Off Time Sleep On Time Volume On time Channel Adjust Time Clock On Time Off Time Sleep On Time Volume On time Channel Off Select Press the UP or DOWN button to select “On Time”. Press the LEFT or RIGHT button to select hour, then press the UP or DOWN button to select the correct hour. Press the LEFT or RIGHT button to select “Off” or “On”, then press the UP or DOWN button to select “Off” or “On”. Off Off Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Function Move Function 10 : 30 am 7 : 30 am - - : - - am Move Off Off Off 10 Menu 81 Setting the Preferred Channel and Volume Level The preferred channel and volume can be set for when the timer automatically turns on the TV. Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the UP or DOWN button to select “Time”, then press the ENTER button. Off Select Press the UP or DOWN button to select “On Time Volume”. Press the LEFT or RIGHT button to adjust volume level. Press the UP or DOWN button to select “On Time Channel”. Press the LEFT or RIGHT button to select the channel. Menu Function English Off Off Off Enter Menu Time Clock - - : - - am On Time - - : - - am Off Time - - : - - am Sleep On Time Volume On Time Channel Move Off Off Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Select Off Off Off 10 Menu Time Clock - - : - - am On Time - - : - - am Off Time - - : - - am Sleep On Time Volume On Time Channel Move Select Off Off Off 10 Menu Function Description Selecting a Menu Language .....................................................84 Viewing Closed Captions .........................................................85 Digital Noise Reduction ...........................................................86 Setting Auto Power Off ...........................................................87 Using the V-Chip .....................................................................88 Selecting the Film Mode ...........................................................94 82 Selecting a Menu Language Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Your TV decodes and displays the closed captions that are broadcast with certain TV shows. These captions are usually subtitles for the hearing impaired or foreignlanguage translations. All VCRs record the closed caption signal from television programs, so home-recorded video tapes also provide closed captions. Most prerecorded commercial video tapes provide closed captions as well. Check for the closed caption symbol in your television schedule and on the tape’s packaging: Note: The Caption feature does not work with DVD or DTV signals. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Viewing Closed Captions Off Off Off Select Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Menu Press the LEFT or RIGHT button to select the appropriate language : English, Français or Español. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the UP or DOWN button to select “Caption”, then press the ENTER button. English Off Off Off Select Menu Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move English English Off Off Off Enter Menu Press the MENU button to exit. Press the LEFT or RIGHT button to turn closed captioning On/Off. Caption Caption Mode Channel Field Move Press the UP or DOWN button to select “Mode”, then press the LEFT or RIGHT button to select “Caption” or “Text.” Select Menu Caption Caption Mode Channel Field Move On Caption On Text Select Menu Depending on the particular broadcast, it might be necessary to make changes to “Channels” and “Field”: Press the UP/DOWN/LEFT/RIGHT button to make the changes. (Follow the same procedure as in steps 3~4 above.) Press the MENU button to exit. Note • Different channels and fields display different information: Field 2 carries additional information that supplements the information in Field 1. (For example, Channel 1 may have subtitles in English, while Channel 2 has subtitles in Spanish. 84 85 1 Digital Noise Reduction Setting Auto Power Off If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. The PDP can be set to turn off automatically if no buttons are pressed for 3 hours after the PDP turns on via the On timer. Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the UP or DOWN button to select “NR”. Press the MENU button to exit. Menu English Press the UP or DOWN button to select “Auto Power Off”. Off Select Menu Function English Off Off Off Select English Off Off Off Select Menu Function Language Time Caption NR Auto Power Off V-Chip Film Mode Menu Menu Function Press the LEFT or RIGHT button to select “On”. Off Move English Language Time Caption NR Auto Power Off V-Chip Film Mode Move On Off Select Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Off Off Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Off Select Function Press the LEFT or RIGHT button to select “On”. Off Off Language Time Caption NR Auto Power Off V-Chip Film Mode Move English English Off On Off Select Menu Press the MENU button to exit. Note • If the Off timer is set, Auto Power Off will not function. • The power will be turned off automatically after 15 minutes if the PDP is ON and there is no input signal. (For instance, if you select a channel without a signal while in TV mode or when there is no input signal after selecting an output signal) 86 87 Using the V-Chip The V-Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal ID number) before any of the V-Chip restrictions are set up or changed. Note : When the V-chip feature is activated, the PIP and auto channel program features do not function. Setting Up Your Personal ID Number (PIN) Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Language Time Caption NR Auto Power Off V-Chip Film Mode The message "Enter Pin" will appear. Enter your 4-digit PIN number. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Off Off Off Select Menu Off Language Time Caption NR Auto Power Off V-Chip Film Mode Menu Press the UP or DOWN button to select “V-Chip”, then press the ENTER button. English Off On Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Off On Off Enter Menu Off Enter Menu The message "Enter Pin" will appear. Enter your 4-digit PIN number. V-Chip Enter Pin V-Chip Enter Pin : ---- Enter Pin Enter Pin : ---- V-Chip V-Chip Lock TV GuideLines MPAA Rating Change Pin Move The Change pin screen will appear. Choose any 4-digits for your PIN and enter them. As soon as the 4 digits are entered, the “Confirm New Pin” screen appears. Re-enter the same 4 digits. When the Confirm screen disappears, your PIN has been memorized. Off Off Function Note: The default PIN number of a new TV set is “0-0-0-0.” The “V-Chip” screen will appear. Press the UP or DOWN button to select “Change Pin,” then press the ENTER button. English Select Move Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Function Move Press the UP or DOWN button to select “V-Chip”, then press the ENTER button. How to Enable/Disable the V-Chip No The “V-Chip” screen will appear. To enable the V-Chip feature, press the RIGHT button so that the “V-Chip Lock” field is Yes. (Pressing the left or right button will alternate between “Yes” and “No”.) V-Chip V-Chip Lock TV GuideLines MPAA Rating Change Pin Move Enter Yes Select Menu Menu V-Chip Press the MENU button to exit. Change Pin Enter New Pin : - - - - V-Chip Confirm New Pin Press the MENU button to exit. Confirm New Pin : Note 88 • If you forget the PIN, press the remote-control buttons in the following sequence, which resets the pin to 0-0-0-0 : Power Off ➔ Mute ➔ 8 ➔ 2 ➔ 4 ➔ Power On. 89 How to Set up Restrictions Using the “TV guidelines” First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating. Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Press the UP or DOWN button to select “V-Chip”, then press the ENTER button. The message "Enter Pin" will appear. Enter your 4-digit PIN number. Off Off Off The “V-Chip” screen will appear. Press the UP or DOWN button to select “TV GuideLines”, press the ENTER button. Off On Off Enter The “TV GuideLines” screen will appear. Press the UP or DOWN button to select one of the six agebased categories: TV-Y TV-Y7 Young children Children 7 and over TV-G TV-PG TV-14 TV-MA General audience Parental guidance Viewers 14 and over Mature audience Note 2: The V-Chip will automatically block certain categories that are “more restrictive”. For example, if you block “TV-Y” category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the “young adult” group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V) work together similarly. (See next section.) Menu V-Chip Enter Pin : ---- How to set the FV, D, L, S and V sub-ratings. First, select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous page). Next, while the TV-Rating is selected, repeatedly press the RIGHT button. This will cycle through the available sub-ratings (FV,L, S, D or V). A blinking letter (“U” or “B”) will be displayed for each sub-rating. While the “U” or “B” is blinking, press the UP or DOWN button to change the sub-rating. Press the RIGHT button to save the TV guidelines. A TV-Rating will be selected and no letters will select. To select a different TV-Rating, press the UP or DOWN button and then repeat the process. Note: The V-chip will automatically block certain categories that are “More restrictive”. For example, if you block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TV-MA will automatically be blocked. Press the MENU button to clear all the screens. (Or proceed to the next section, and set up additional restrictions based on the MPAA codes). V-Chip V-Chip Lock TV GuideLines MPAA Rating Change Pin Move FV: Fantasy violence D: Sexually Sugessive Dialog L: Adult Language S: Sexual situation V: Violence English Enter Pin Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to change any of the following sub-ratings: Menu Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Select No Enter Menu TV GuideLines TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Move All FV At this point, one of the TV-Ratings is selected. Press the RIGHT button : Depending on your existing setup, a letter “U” or “B” will start blinking. (U= Unblocked, B= Blocked) While the “U” or ”B” is blinking, press the UP or DOWN button to block or unblock the category. Press the RIGHT button to save the TV guidelines. A TV-Rating will be selected, and no letters will blink. To select a different TV-Rating, press the UP or DOWN button and then repeat the process. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move V S L D B : Blocked U : Unblocked Select Menu Note • Note: These categories consist of two separate groups: TV-Y and TV-Y7 (young children through age 7), and TV-G through TV-MA (everybody else). The TV-Y and TV-Y7 categories are colored blue. The restrictions for these two groups work independently: If a household includes very young children as well as young adults, the TV guidelines must be set up separately for each age group. (See next step.) 90 91 How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”) The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is for movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with objectionable ratings (either MPAA or TV-Ratings). If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: “Excessive rating.” Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the UP or DOWN button to select “V-Chip”, then press the ENTER button. The message "Enter Pin" will appear. Enter your 4-digit PIN number. English Off Off Off Select The “V-Chip” screen will appear. Press the UP or DOWN button to select “MPAA Rating,” press the ENTER button. Off On The “MPAA Rating” screen will appear. MPAA category. Pressing the UP or DOWN button will cycle through the MPAA categories: General audience (no restrictions). PG Parental guidance suggested. PG-13 PG-13 (Parents strongly cautioned). Press the UP or DOWN button to select “V-Chip”, then press the ENTER button. Enter your PIN number, and press the RIGHT button to temporarily disable the V-Chip Lock. Off Enter Menu V-Chip Enter Pin : ---- V-Chip V-Chip Lock TV GuideLines MPAA Rating Change Pin Move Press the MENU button. English Enter Pin Menu Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the channels. In this case, use the V.Chip function for an “emergency escape”: No Enter Menu MPAA Rating PG PG-13 NC-17 NR Move B : Blocked U : Unblocked Enter Menu R (Restricted. Children under 17 should be accompanied by an adult). NC-17 No children under age 17. 92 X (Adults only). NR Not rated. While a particular category is selected, press the RIGHT button to activate it. A selected letter (“U” or “B”) will be displayed. Press the UP or DOWN button to select “U” or ”B”. Press the RIGHT button to save the settings. Note: The V-Chip will automatically block any category that is “more restrictive. ”For example, if you block the “PG-13” category, then “R”, “NC-17” and “X” will automatically be blocked also. 93 Selecting the Film Mode Press the MENU button. Press the UP or DOWN button to select “Function”, then press the ENTER button. Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move Press the DOWN button to select Film Mode, then press the RIGHT or LEFT button to select “On” or “Off”. •On: Automatically senses and processes film signals from all sources and adjusts the picture for optimum quality. •Off: Switches off the Film mode. English Off Off Off Select Menu Function Language Time Caption NR Auto Power Off V-Chip Film Mode Move English Off Off On Select Menu Press the MENU button to exit. Note • Film mode is supported in Video, S-Video, Component 480i. Appendix Troubleshooting............................................................................96 Care and Maintenance ................................................................97 Specifications ..............................................................................98 94 Care and Maintenance Troubleshooting Before you call a service technician, please scan this list of problems and possible solutions. It may save you time and money. With proper care, your PDP will give you many years of service. Please follow these guidelines to get the maximum performance from your PDP. Identifying Problems Problem Possible Solution Poor picture. Check all wire connections. Your Remote control does not operate the PDP. Press the “Mode” button to put your remote control in the “TV” mode. The PDP won’t turn on. Check if the power plug is connected. There is no screen image. Check to see that both the PDP and the source are plugged in and turned on. • • • • Do not put the PDP near extremely hot, cold, humid or dusty places. Do not put the PDP near appliances that create magnetic fields. Keep the ventilation openings clear. Do not place the PDP on a rough and slanted surface, such as cloth or paper. Liquids • Do not place liquids near or on the PDP. Cabinet 96 The image is too light or too dark. Adjust the Brightness or Contrast settings. The image is too large or too small. Adjust the Size settings. • Never open the cabinet or touch the parts inside. • Wipe your PDP with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals. • Do not put heavy objects on top of the cabinet. Temperature • If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two hours so that moisture that may have formed inside the unit can dry completely. 97 Specifications Memo Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. This PDP applies to Class B digital device. (Note: Class B system is for home use.) This PDP has been registered for residential use in terms of EMI. So it can be used in all areas as well as residential areas. HPN4235 Model Dimensions Display Remote Control Weight Display Remote Control Voltage Power Consumption Number of Pixels Screen Size ANTENNA input VIDEO input 1027 (W) X 86.5 (D) X 630.5 (H) mm ; 40.43 (W) X 3.11 (D) X 24.82(H) inches 58 (W) X 21 (D) X 210 (H) mm ; 2.28 (W) X 0.83 (D) X 8.27 (H) inches 37 kg 134g ; 0.295 lbs (including batteries) 120V~, 60Hz 330 Watts 1024(H) x 768(V) 107 Cm/42 inches VHF, UHF (75Ω unbalanced) VIDEO S-VIDEO COMPONENT 1 - 480i / 480p / 720p / 1080i COMPONENT 2 - 480i / 480p / 720p / 1080i RGB : D-SUB 15P DVI AUDIO input VIDEO / S-VIDEO COMPONENT 1 COMPONENT 2 PC (RGB) DVI AUDIO output 10W + 10W (8 Ω) Subwoofer (500mv RMS at 1KHz) 98 99
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:05:09 09:56:07Z Modify Date : 2003:07:22 17:56:57-03:00 Page Count : 35 Creation Date : 2003:05:09 09:56:07Z Producer : Acrobat Distiller 4.0 for Macintosh Mod Date : 2003:07:22 17:56:57-03:00 Metadata Date : 2003:07:22 17:56:57-03:00 Has XFA : NoEXIF Metadata provided by EXIF.tools