Samsung Electronics Co SC148B CD-ROM Drive User Manual

Download:
Mirror Download [FCC.gov]
Document ID	35045
Application ID	kUD/TX1fuln4LZ26sMENCQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.07kB (138417 bits)
Date Submitted	1999-04-29 00:00:00
Date Available	1999-06-24 00:00:00
Creation Date	1999-04-15 09:44:24
Producing Software	Acrobat Distiller 3.01 for Windows
Document Lastmod	1999-04-28 15:54:15
Document Title	Users Manual
Document Creator	QuarkXPress3.3k
Document Author:	¿µÃ¢1

CD-ROM DRIVE
SC-140/148
User's Guide - ENGLISH
When handling the drives, you may hear a slight
rattle inside the unit.
This is NOT a problem, it is simply the ball
bearings of the Auto Balancer shifting.
http://www.samsungelectronics.com
BG68-00044A Rev 02
Safety Warnings
The following diagrams illustrate the precautions to be taken when using your
CD-ROM drive.
You must not use the drive in any manner other than that specified in this guide.
CAUTION
Do not attempt to repair the CD-ROM drive yourself. Contact your
dealer or local SAMSUNG representative for all repairs.
Use of controls or adjustments or performance of procedures other
than those specified here in may result in hazardous radiation
exposure
To reduce the risk of fire or electric shock, do not expose this appliance to rain or
moisture.
WARRANTY
Please refer to the Samsung limited warranty statements.
Front View of the CD-ROM Drive
COMPACT
Headphone Connector
Volume Control Dial
LED
Emergency Hole
5 6
The audio output connector enables you to plug stereo headphones into the drive. It requires a 3.6
mm stereo mini-jack.
This control dial adjusts the volume for your headphones. You can only use the headphone jack and
volume control when you have installed the required software utilities. For example, the Microsoft
Windows Media player can be used.
Disc Tray
The Disc Tray opens and closes automatically when you press the Open/Close button.
◆ When you place a disc in the tray, make sure that the label on the disc is
facing upwards. If you are not loading or unloading a disc, the disc tray should
remain closed.
If the disc tray does not open when you press the Open/Close
button, insert a small, metal rod(an unwound paper clip for example) into this
hole to eject the disc.
☛This function should only be performed when the computer is powered OFF.
Stop/Open/Close-Button
When in play, press the stop key and when in stop, press open/close key.
Rear View of the CD-ROM Drive
1 2 3
Digital Audio
Audio Output Connector
Device Configuration Jumper
You can connect a sound card or MPEG card which support Digital Audio to your drive using this
two-pin connector.
You can connect a sound card to your drive using this four-pin connector.
☛ This function is not covered in detail in this guide. Refer to the documentation
supplied with your sound card.
Usually, this is a pre-set configuration as illustrated below.
C S M
S L A
☛ Verify that the setting is as illustrated. If it is not, simply remove the jumper
and place it in the correct position.
Host IDE Interface connector
Power Connector
This input/output interface connector is used to connect the 40-pin flat cable from the IDE
interface to the CD-ROM drive.
The power connector is a four-conductor male plug.
System Requirements
Before you install the CD-ROM drive, we strongly recommend that you
make certain that your set-up meets the system requirements listed below.
Free expansion unit
Description
IBM 486SX 20MHz (or higher) with
an IDE interface(or a 100% IBMcompatible computer)
5.25 inch
Disk space
100KB minimum
MS-DOS version
5.0(or higher)
Windows version
3.1(or higher)
Item
Type of computer
Installing the CD-ROM Drive
Install the CD-ROM drive in your computer horizontally, making sure that the
To install the drive, proceed as follows.
Turn OFF your computer. Remember to verify the configuration
jumper on the rear of the CD-ROM drive.
Install the CD-ROM drive into the unit and secure it with mounting
screws (recommended standard M3x6x4)
☛ ◆ Depending on your PC model, you may need to
attach guide rails to the drive, so that the drive is
held firmly in place.
☛ ◆ If you use screws that are longer than the
recommended standard, you may damage the
drive.
Put the cover back on your PC.
Remove the cover of your PC(main unit of the computer)
Remove the blank cover panel of the 5.25 inch unit in which the
CD-ROM drive is to be installed.
Connect the CD-ROM drive to the IDE interface and power cables
Iocated inside your computer.
☛ Connectors are keyed so it is impossible to put them in
an incorrect position. Do not force the connectors, if they
do not seem to fit.
Installing the Software
You can install the device driver for DOS or for Windows
¡ Do not install DOS Driver when the program of Windows 95 is going on.
(Remark CD-ROM Driver in the state of Config. Sys.)
Turn on your computer and wait for it to boot.
Insert the driver disk into a floppy disk drive(usually the A drive).
If you are a...
Then :
DOS user
◆ Type a: at the DOS prompt
◆ Press the RETURN key
◆ Access the File Manager
◆ Click on the A icon.
Windows user
Windows 95user
Run the CDSETUP program:
Then :
If you are a...
DOS user
Windows user
◆ When you are in Windows 95, it is not
◆ necessary to install Device Driver.
◆ Whereas, when you are in Dos Mode of
◆ Windows 95, then install as follows.
◆ Click on MY COMPUTER icon.
◆ Click on the A icon.
◆ Type CDSETUP after the a: prompt
◆ Press RETURN
Double-click CDSETUP.EXE from the Windows
File Manager
To...
Then enter...
Confirm the installation
Exit without installing
If you answer Y(Yes), the installation program automatically
Result :
◆ Creates a SAMSUNG directory on your hard disk
◆ Copies the required softwares (mscdex.exe and sscdrom.sys)
◆ Modifies the CONFIG.SYS and AUTOEXEC.BAT files
When the Setup Completed screen is displayed, remove the
installation floppy disk from the drive.
Reboot your system.
◆ The computer restarts
Result :
◆ Both the device driver and MSCDEX are loaded
Resolving Technical Problems
☛ Please consult the following table BEFORE contacting your dealer or local SAMSUNG
☛ representative.
Problem
The software installation failed
Meaning / Solution
◆ Check that your hard disk is not full
◆ The installation floppy disk may be corrupted.
Repeat the installation with the backup floppy disk.
I re-booted my PC and it paused during
the start-up program.
After installing the device driver, your system start-up
program may take more time than expected. If it does not
start-up after 60 seconds, verify your AUTOEXEC. BAT file
and, if necessary, contact your local computer dealer.
The disc tray does not open.
The drive may not be installed correctly. Verify the
physical installation.
In the File Manager, the CD-ROM icon
does not display.
If you have installed the Then ...
CD-ROM drive ...
I installed the software and rebooted my PC. The CD-ROM drive
icon/directory still does not appear.
And the software
Re-boot your PC.
And have not installed the
software
Install the software
following the instructions
on page 5
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
When the program of Windows 95 is broken up, re-stall
it as the computer can not read the program anymore.
Verify the connections between the drive and your PC.
Check that the 40-pin flat cable is connected to an IDE
interface (some PCs are equipped with an SCSI disk
interface)
Verify your AUTOEXEC. BAT file. Go to page 6 for
the verification procedure.
Check the LASTDRIVE = command in the CONFIG. SYS
file. The specified letter must take the CD-ROM volume
into account. If you do not know which letter is assigned
to the CD-ROM, enter Z.
Using the documentation provided with your PC, check
that the IDE hard disk is set up in MASTER mode.
Technical Specifications
SAMSUNG continually strives to improve its products. Both the design
specifications and these user instructions are thus subject to change without
notice.
SECTIONS
DISC
Disc types supported
SC-140
12cm or 8cm
Max. 6000KB/s
Max. 7200KB/s
PIO Mode - 4. DMA MW2(option), Ultra DMA
Disc diameter
Data transfer rate
DRIVE PER FORMANCE
Access time (1/3 stroke)
Data buffer capacity
Laser
Slide mechanism
Spindle motor
Loading type
Semiconductor Laser
Gear motor
Brushless motor
Tray Loading, DC motor(Soft Eject)
Indicator(LED)
PLAY(Open/Close)
Busy
Headphone output
Stereo Mini - jack (Ø 3,6 mm) 0.60 ± 20% (Vrms) 33Ω
Volume control
Dial type
Required power
+5V DC 1.7A,
+12V DC 1.0A (Max)
Interface connector
ATAPI
Audio output
Line out 0.70 ± 20%(Vrms), 47kΩ
Jumper block
Work area
OPERATING
ENVIRONMENT Storage area
Device configuration jumper
Temperature : 5~45 °C, Humidity : 8~80%
Temperature : -40~60 °C, Humidity : 5~90%
Dimensions
149(W) x 42.5(H) x 200(D)mm
(Including bezel)
Net weight
950g
MTBF
125,000 POH(Duty 25%)
30,000 times
GENERAL
RELIABILITY
70ms(typical)
12
Button
REAR PANEL
80ms(typical)
128KB
Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits
ERROR RATE
FRONT PANEL
SC-148
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,
Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session), Video
CD ready, Enhanced CD, CD-I/FMV, CD-R
Disc compartment loading

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 1999:04:15 09:44:24
Producer                        : Acrobat Distiller 3.01 for Windows
Author                          : ¿µÃ¢1
Creator                         : QuarkXPress3.3k
Title                           : µµÅ¥¸àÆ®3
Modify Date                     : 1999:04:28 15:54:15
Page Count                      : 8

EXIF Metadata provided by EXIF.tools