Samsung Electronics Co SGHS108 Single-Mode PCS GSM Phone User Manual

Download:
Mirror Download [FCC.gov]
Document ID	265878
Application ID	hd2Y8PtWmXLl+NXscF8m7Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	91.8kB (1147528 bits)
Date Submitted	2002-08-26 00:00:00
Date Available	2002-08-23 00:00:00
Creation Date	2002-07-19 09:19:47
Producing Software	Acrobat Distiller 4.0.5 for Macintosh
Document Lastmod	2002-08-12 12:11:24
Document Title	Users Manual

* Some of the contents in this manual may differ from your phone,
depending on the software installed or your service provider.
TRI BAND
GPRS TELEPHONE
SGH-S108
Draft version
(2002. 07. 18)
ELECTRONICS
World Wide Web
http://www.samsungmobile.com
Printed in Korea
Code No.: GH68-xxxxxA
English. 07/2002. Rev. 1.0
FCC RF EXPOSURE INFORMATION
WARNING!
Read this information before using your phone
In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and
Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic
energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard
previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC
guidelines and these international standards.
Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could
impair call quality, damage the phone, or result in violation of FCC regulations.
Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor
burn may result. Please contact your local dealer for replacement antenna.
Body-worn Operation
This device was tested for typical body-worn operations with the back of the phone kept 1.5 cm. from the body. To
maintain compliance with FCC RF exposure requirements, use only belt-clips, holsters or similar accessories that
maintain a 1.5 cm. separation distance between the user’s body and the back of the phone, including the antenna,
whether extended or retracted. The use of belt-clips, holsters and similar accessories should not contain metallic
components in its assembly. The use of accessories that do not satisfy these requirements may not comply with
FCC RF exposure requirements, and should be avoided.
For more information about RF exposure, please visit the FCC website at www.fcc.gov
Contents
Important Safety Precautions . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . 9
Your Phone . . . . . . . . . . . . . . . . . . . . .
Phone Layout. . . . . . . . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . . .
Service Light . . . . . . . . . . . . . . . . . . . . .
10
10
13
16
Getting Started . . . . . . . . . . . . . . . . . .
Installing the SIM Card . . . . . . . . . . . . . .
Charging a Battery . . . . . . . . . . . . . . . . .
Switching the Phone On/Off . . . . . . . . . . .
17
17
19
21
Call Functions . . . . . . . . . . . . . . . . . . .
Making a Call. . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . .
Answering a Call . . . . . . . . . . . . . . . . . .
Viewing Missed Calls . . . . . . . . . . . . . . . .
Switching Quickly to the Silent Mode . . . . .
22
22
24
25
26
28
Selecting Functions and Options . . . . . 2 9
Example: Setting the Display Language . . . 31
Phonebook .....................
Storing a Number with a Name. . . . . . . . .
Using Phonebook Entry Options . . . . . . . .
Searching for a Number
in the Phonebook . . . . . . . . . . . . . . . . . .
Editing a Caller Group . . . . . . . . . . . . . . .
Speed-Dialling . . . . . . . . . . . . . . . . . . . .
Checking Memory Status . . . . . . . . . . . . .
33
33
35
37
39
40
41
Entering Text. . . . . . . . . . . . . . . . . . . . 4 2
Changing the Text Input Mode . . . . . . . . . 43
Using the Chinese Pinyin Mode . . . . . . . . . 45
Using the Chinese Stroke Mode . . . . . . . . 47
Using the Quick English Mode . . . . . . . . . . 50
Contents
In-Call Options (continued)
Using the English Mode . . . . . . . . . . . . . .
Using the Number Mode . . . . . . . . . . . . .
Using the Symbolic Mode. . . . . . . . . . . . .
Using Help . . . . . . . . . . . . . . . . . . . . . .
Contents
52
54
54
54
In-Call Options . . . . . . . . . . . . . . . . . .
Putting a Call on Hold . . . . . . . . . . . . . . .
Switching the Microphone Off (Mute) . . . . .
Muting/Sending Key Tones . . . . . . . . . . . .
Searching for a Number
in the Phonebook . . . . . . . . . . . . . . . . . .
Using the SMS Service . . . . . . . . . . . . . .
Answering a Second Call . . . . . . . . . . . . .
Making a Multiparty Call . . . . . . . . . . . . .
55
55
56
57
Using the Menus . . . . . . . . . . . . . . . . .
Accessing Menu Functions by Scrolling . . . .
Accessing Menu Functions
by Using Shortcuts . . . . . . . . . . . . . . . . .
List of Menu Functions . . . . . . . . . . . . . .
61
61
Messages. . . . . . . . . . . . . . . . . . . . . . .
Read Messages (Menu 1.1) . . . . . . . . . . .
W rite Messages (Menu 1.2). . . . . . . . . . .
Templates (Menu 1.3) . . . . . . . . . . . . . .
Setup (Menu 1.4) . . . . . . . . . . . . . . . . .
Broadcast (Menu 1.5) . . . . . . . . . . . . . .
Voice Mail (Menu 1.6) . . . . . . . . . . . . . .
My Contents (Menu 1.7) . . . . . . . . . . . . .
Memory Status (Menu 1.8) . . . . . . . . . . .
67
67
69
71
71
73
74
75
75
Call Records. . . . . . . . . . . . . . . . . . . . .
Missed Calls (Menu 2.1) . . . . . . . . . . . . .
Received Calls (Menu 2.2) . . . . . . . . . . .
Dialled Calls (Menu 2.3) . . . . . . . . . . . . .
Call Time (Menu 2.4) . . . . . . . . . . . . . . .
Call Cost (Menu 2.5) . . . . . . . . . . . . . . .
76
76
76
77
77
78
57
58
58
59
62
62
Sound Settings . . . . . . . . . . . . . . . . . .
Ring Tone (Menu 3.1) . . . . . . . . . . . . . .
Ring Volume (Menu 3.2). . . . . . . . . . . . .
Alert Type (Menu 3.3) . . . . . . . . . . . . . .
Keypad Tone (Menu 3.4) . . . . . . . . . . . .
Message Tone (Menu 3.5) . . . . . . . . . . . .
Extra Tones (Menu 3.6) . . . . . . . . . . . . .
79
79
79
80
80
81
82
Phone Settings . . . . . . . . . . . . . . . . . .
Infrared Activate (Menu 4.1) . . . . . . . . . .
My Settings (Menu 4.2) . . . . . . . . . . . . .
Greeting Message (Menu 4.3) . . . . . . . . .
Own Number (Menu 4.4) . . . . . . . . . . . .
Language (Menu 4.5). . . . . . . . . . . . . . .
Security (Menu 4.6). . . . . . . . . . . . . . . .
Display Settings (Menu 4.7) . . . . . . . . . .
Extra Settings (Menu 4.8). . . . . . . . . . . .
ShortCut (Menu 4.9) . . . . . . . . . . . . . . .
Reset Settings (Menu 4.10). . . . . . . . . . .
83
83
84
75
85
86
86
89
91
92
82
Organiser . . . . . . . . . . . . . . . . . . . . . . 9 3
Calendar (Menu 5.1) . . . . . . . . . . . . . . . 93
To Do List (Menu 5.2) . . . . . . . . . . . . . . 95
Time & Date (Menu 5.3). . . . . . . . . . . . . 97
Alarm (Menu 5.4) . . . . . . . . . . . . . . . . . 97
Calculator (Menu 5.5). . . . . . . . . . . . . . 100
Currency Exchange (Menu 5.6) . . . . . . . 101
Network Services. . . . . . . . . . . . . . . .
Call Diverting (Menu 6.1) . . . . . . . . . . .
Call Barring (Menu 6.2) . . . . . . . . . . . .
Call Waiting (Menu 6.3) . . . . . . . . . . . .
Network Selection (Menu 6.4) . . . . . . . .
Caller ID (Menu 6.5) . . . . . . . . . . . . . .
Closed User Group (CUG) (Menu 6.6) . . .
Band Selection (Menu 6.7) . . . . . . . . . .
102
102
104
106
107
108
108
110
Contents
Funbox .......................
Games (Menu 7.1). . . . . . . . . . . . . . . .
W AP Browser (Menu 7.2) . . . . . . . . . . .
Downloads (Menu 7.3) . . . . . . . . . . . . .
111
111
111
111
Solving Problems . . . . . . . . . . . . . . . . 1 1 4
Access Codes . . . . . . . . . . . . . . . . . . .
Phone Password . . . . . . . . . . . . . . . . . .
PIN . . . . . . . . . . . . . . . . . . . . . . . . . .
PUK ..........................
PIN2. . . . . . . . . . . . . . . . . . . . . . . . . .
PUK2 . . . . . . . . . . . . . . . . . . . . . . . . .
Barring Password . . . . . . . . . . . . . . . . .
117
117
118
118
119
119
120
Health and Safety Information. . . . . .
Information about Batteries . . . . . . . . . .
Precautions When Using Batteries . . . . . .
Road Safety. . . . . . . . . . . . . . . . . . . . .
Operating Environment . . . . . . . . . . . . .
Potentially Explosive Atmospheres . . . . . .
Emergency Calls. . . . . . . . . . . . . . . . . .
Other Important Safety Information . . . .
Care and Maintenance . . . . . . . . . . . . . .
121
121
123
125
127
129
130
131
132
Glossary . . . . . . . . . . . . . . . . . . . . . . 1 3 4
Important Safety
Precautions
Read these guidelines before using your wireless
phone. Failure to comply with them may be
dangerous or illegal. For more detailed safety
information, see Health and Safety Information
on page 121.
Road Safety at All Times
Do not use a hand-held phone while driving;
park the vehicle first.
Switching Off When Refuelling
Do not use the phone at a refuelling point
(service station) or near fuels or chemicals.
Switching Off in Aircraft
Wireless phones can cause interference. Using
them in aircraft is both illegal and dangerous.
Switching Off in Hospitals
Switch off your phone near medical equipment.
Follow any regulations or rules in force.
Interference
All wireless phones may be subject to
interference, which could affect their
performance.
Special Regulations
Meet any special regulations in force in any area
and always switch off your phone whenever it is
forbidden to use it, or when it may cause
interference or danger (in a hospital for
example).
Important Safety Precautions
Unpacking
Sensible Use
Use only in the normal position (held to the ear).
Avoid unnecessary contact with the antenna
when the phone is switched on.
Your package contains the following items.
Handset
Travel Adapter
Battery
Ear-Microphone
User s Manuals
Data Cable
Accessories and Batteries
Use only Samsung-approved accessories and
batteries.
Qualified service
Only qualified service personnel may install or
repair your phone.
Software CD-ROM
In addition, you can obtain the following
accessories for your phone from your local
Samsung dealer:
¥
¥
¥
¥
Desktop charger
¥ Ear-microphone
Simple hands-free kit
¥ Car holder
Standard/extended batteries
Cigarette lighter adapter
Your Phone
Your Phone
Key
Phone Layout
In menu mode, scroll through the
menu options and phonebook memory.
The following illustrations show the main
elements of your phone.
Earpiece
Folder
Description
Display
In idle mode, allow you to access your
favourite menu options directly (for
more information on shortcuts, see
page 92).
In menu mode, return to the previous
menu level and select the current
menu respectively.
When entering text, move the cursor
left and right respectively.
N avigation keys
Volume/menu
browse keys
Soft key (left)
Dial/menu
confirmation key
Cancel/
correction key
Soft key (right)
W AP Browser
key
Power on/off /
menu exit key
In idle mode, allow you to access your
favourite menu options directly (for
more information on shortcuts, see
page 92).
Perform the functions indicated by the
text above them (on the bottom line of
(soft keys) the display).
Alphanumeric
keys
In idle mode, launches the WAP
browser directly.
Special function
keys
Deletes characters from the display.
In menu mode, returns to the previous
menu level.
IrDA port
Microphone
Antenna
Ear-microphone
jack
Service light
External display
10
M a kes or answers a call.
When held down in idle mode, recalls
the last number dialled or received.
In menu mode, selects a menu
function or stores information that you
have entered (such as a name) in the
phone or SIM memory.
11
Your Phone
Key
Your Phone
Description
Display
Ends a call. Also switches the phone on
and off when held down.
Display Layout
In menu mode, cancels your input and
returns to the idle mode.
The display comprises three areas.
When held down in idle mode,
accesses your voice mail.
Icons
Text and
graphic area
Enter numbers, letters and some
special characters.
Enter special characters.
Menu
Name
Perform the various functions.
Soft keys
indications
(on the side of the phone)
During a call, adjust the earpiece
volume.
Area
Description
First line
Displays various icons (see page
14).
Middle lines
Display messages, instructions
and any information that you
enter (number to be dialled, for
example).
Last line
Shows the functions currently
assigned to the two soft keys.
In idle mode, adjust the key volume.
In menu mode, scroll through the
menu options and phonebook memory.
12
13
Your Phone
Icons
Icon
Your Phone
Backlight
Description
Shows the received signal strength. The
greater the number of bars, the better
the signal strength.
The display is illuminated by a backlight. When
you press any key or open the phone, the
backlight illuminates. It turns off if no key is
pressed within a given period of time, depending
on the Back Light menu option.
Appears when a call is in progress.
Appears when you are connected to the
GPRS network.
To specify the length of time for which the
backlight is active, set the Back Light m e n u
option (Menu 4.7.2); see page 89 for further
details.
Appears when you set the alarm.
Appears when a new text message has
been received.
Appears when a new voice mail
message has been received.
You can also set the phone to use the backlight
only during a specified period time, via the Auto
Light menu option (Menu 4.7.3); see page 90
for further details.
Appears when you are entering text to
indicate the current text input mode.
External Display
Appears when the Silent mode is active
or you set the Alert Type menu option
(Menu 3.3), so that the phone vibrates
when you receive a call; for further
details, see page 80.
Your phone has an external display on the cover.
It indicates that you have an incoming call or a
message, and notifies you at the specified time
when you set an alarm.
Shows the level of your battery. The
more bars you see, the more power you
have left.
Appears when the IrDA port is active.
For details, see page 83.
Appears when you are out of your home
area and have registered onto a
different network, when travelling in
other countries, for example.
Appears when the Mute mode is active.
14
15
Your Phone
Getting Started
Service Light
Installing the SIM Card
The service light is in the top right-hand corner
of the phone. It flashes when services are
available on the phone.
To activate or deactivate use of the service light,
set the Service Light menu option (M e n u
4.7.4); see page 90 for further details.
When you subscribe to a cellular network, you
are provided with a plug-in SIM card loaded with
your subscription details, such as your PIN, any
optional services available and so on.
Important! The plug-in SIM card and its
contacts can be easily damaged by
scratching or bending, so be careful
when handling, inserting or
removing the card.
Keep all SIM cards out of the reach
of small children.
Service light
1. If necessary, switch off the phone by holding
down the
key until the power-off image
is displayed.
2. Re m ove the battery. To do so:
➀ Press down the catch above the battery
and hold it in this position.
➁ Slide the battery and lift it aw ay, as shown.
➀
➁
16
17
Getting Started
3. Slide the SIM card into the SIM card holder so
that the holder locks the card in position.
M a ke sure that the cut corner is top right and
the gold contacts of the card face into the
phone.
Getting Started
5. Slide the battery towards the top of the phone
until it clicks into place. Make sure that the
battery is properly installed before switching
on the power.
Charging a Battery
Note: When you need to remove the SIM card,
slide it, as shown, and take it out of the
holder.
Your phone is powered by a rechargeable Li-ion
battery. A travel adapter is provided with your
phone. Use only approved batteries and
chargers. Ask your local Samsung dealer for
further details.
The phone can be used while the battery is
charging, but this will cause the phone to charge
more slowly.
Note: You must fully charge the battery before
using your phone for the first time. A
discharged battery is fully recharged in
approximately 200 minutes.
4. Place the battery back, taking care to match
the tabs on the battery with the grooves on
the phone.
18
1. With the battery in position on the phone,
connect the lead from the travel adapter to
the bottom of the phone.
19
Getting Started
Getting Started
2. Connect the adapter to a standard AC wall
outlet.
3. When charging is finished, disconnect the
adapter from the power outlet and from the
phone by pressing the grey tabs on both sides
of the connector and pulling the connector
out.
➀
➁
Switching the Phone On/Off
1. Open the folder.
2. Hold down the
switches on.
key until the phone
3. If the phone asks for a password, key in the
password and press the O K soft key. The
phone password is factory set to 00000000.
For further details, see page 117.
4. If the phone asks for a PIN, key in the PIN
and press the O K soft key. For further details,
see page 118.
➀
Low Battery Indicator
When the battery is weak and only a few
minutes of talk time remain, you will hear a
w arning tone and a message will be repeated at
regular intervals on the display:
The phone searches for your network and
when it finds it, the idle screen, illustrated
below, appears on each display. Now, you can
m a ke or receive a call.
Service Provider
07:30
W ed 06 Mar
07:30
(wed)03/06
* * Warning**
Low Battery
Menu
Name
Note: To change the language, use the Language
menu option (Menu 4.5); for further details,
refer to page 86.
Menu
Name
When the battery becomes too weak for the
phone to operate, it switches off automatically.
20
5. When you wish to switch the phone off, hold
down the
key until the power-off image
is displayed.
21
Call Functions
Call Functions
Ending a Call
Making a Call
When you want to finish your call, briefly press
the
key.
When the idle screen is displayed, key in the
area code and phone number, and press the
key.
Note: If you have checked the Auto Redial option
in the Extra Settings menu (Menu 4.8),
the number is redialled automatically up to
ten times when the person does not answer
the call or is already on the phone; see page
91 for further details.
Making an International Call
1. Press and hold down the 0 key.
The + character appears.
2. Key in the country code, area code and phone
number and press the
key.
Correcting the Number
To clear...
Press the...
The last digit
displayed
C key.
A ny other digit
or key until the cursor
in the number
is immediately to the right of the digit to be
cleared. Press the C key. You can also insert a
missing digit simply by pressing the appropriate
key.
The whole display
22
the C key for more than
one second.
Redialling the Last Number
The phone stores the numbers you dialled,
received or missed if the caller is identified; see
Call Records on page 76 for further details.
To recall any of these numbers:
1. If you have typed any characters on the
display, clear the display by holding down the
C key for more than one second.
2. Press the
key to display a list of the last
numbers in the order in which the calls were
made.
3. Use the
and
keys to scroll through
the numbers until the required number is
highlighted.
4. To...
Then...
Dial the number
highlighted
Press the
key.
Edit the number
highlighted
¥ Press the Edit soft key.
¥ Change the number as
required, referring to
Correcting the
Number on page 22
for further details.
23
Call Functions
Call Functions
Making a Call from the Phonebook
You can store frequently-dialled phone numbers
with a name in the SIM card or the phone
m e m o r y, using the phonebook. You then simply
select the required name to recall the associated
number. For further details on the Phonebook
features, refer to page 33.
Answering a Call
When somebody calls you, the phone rings and
the following screen appears on each display.
Adjusting the Volume
Accept
During a call, if you want to adjust the earpiece
volume, use the
and
keys on the left side
of the phone.
Press the
key to increase and the
decrease the volume.
key to
Reject
If the caller can be identified, the caller s phone
number or name, if stored in your phonebook, is
displayed.
1. If necessary, open the folder. Press the
key
or the Accept soft key to answer the incoming
call.
If the Anykey Answer option in the Extra
Settings menu (Menu 4.8) is checked, you
can press any key to answer a call except for
the
key and the Reject soft key (see
page 91).
If the Active Flip option in the Extra Settings
menu (Menu 4.8) is checked, you can answer
the call simply by opening the folder (see page
91).
In idle mode with the folder open, you can
adjust the key volume using the
and
keys.
Note: To reject an incoming call, press and hold
the volume keys on the left side of the
phone without opening the folder.
2. End the call by closing the folder or pressing
the
key.
Note: You can answer a call while using the
phonebook or menu features.
24
25
Call Functions
Call Functions
Viewing Missed Calls
Editing a Missed Call Number
If you are unable to answer a call for any
reason, you can find out who was calling you,
provided that this service is available. In this
w ay, you can call the person back, if necessary.
Note: If the number corresponding to the missed
call is not available, the Edit Number option
is not displayed.
The number of missed calls is displayed on the
idle screen immediately after a call was missed.
To view the missed call immediately:
1. Press the Options soft key.
2. Press the
or
key to highlight the
Edit Number option.
3. Press the Select soft key.
1. If the phone is closed, open the folder.
4. Change the number as required.
2. Press the V i e w soft key.
The number corresponding to the most recent
missed call is displayed, if available.
3. To....
Press the...
Scroll through the
missed calls
or
Call the number
displayed
key.
Edit or delete a
missed call number
key.
5. To...
Press the...
Call the number
Store the
number
key.
Save soft key and enter
the name and location
required (for further
details, refer to page 33).
Deleting a Missed Call
Select soft key
(see the following
page).
1. Press the Options soft key.
2. If necessary, press the
or
highlight the Delete option.
key to
3. Press the Select soft key.
You can press the key at any time to exit the
Missed Call feature.
Note: You can access the Missed Call feature at
any time by selecting the Missed Calls
menu option (Menu 2.1); for further details,
see page 76.
26
27
Call Functions
Switching Quickly to the Silent
Mode
The Silent Mode is convenient when discretion is
required and you a wish to stop the phone from
making any noise, in a theatre for example.
In idle mode, to switch your phone quickly to
the silent mode, simply press and hold down the
key until the Silent Mode message and
vibration icon ( ) are displayed.
In the silent mode, your phone changes the
sound settings as follows:
Option
New Setting
Alert Type (Menu 3.3)
Vibration
Keypad Tone (Menu 3.4)
OFF
SMS Tone (Menu 3.5.1)
Light Only
Error Tone (Menu 3.6.1)
OFF
Selecting Functions
and Options
Your phone offers a set of functions that allow
you to customise your phone. These functions
are arranged in menus and sub-menus, accessed
via the two soft keys marked
and
. Each
menu and sub-menu allows you to view and
alter the settings of a particular function.
The roles of the soft keys vary according to the
current context; the label on the bottom line of
the display just above each key indicates its
current role.
Example:
Service Provider
07:30
W ed 06 Mar
Menu
Name
To exit the silent mode and reactivate the
previous Sound Settings, press and hold the
key again until Exit Silent Mode appears. The
vibration icon ( ) is no longer displayed.
Press the left soft
key to access the
main menu mode.
28
Press the right soft
key to access the
Phonebook menu.
29
Selecting Functions and Options
Selecting Functions and Options
To view the various functions/options available
and select the one required:
1. Press the appropriate soft key.
2. To...
1. When the idle screen is displayed, press the
M e n u soft key to access the menus.
Press the...
Select the:
¥ Function displayed
or
¥ Option highlighted
Select soft key or
the
key.
View the next function
or highlight the next
option in a list
key or
key
on the left side of
the phone.
M ove back to the
previous function
or option in a list
key or
key
on the left side
of the phone.
M ove back up one
level in the structure
key,
soft key
or C key.
Exit the structure
without changing
the settings
Example: Setting the Display
Language
Service Provider
07:30
W ed 06 Mar
Menu
Name
2. Scroll through the menus until you reach the
Phone Settings menu, by pressing the
or
key.
Call
Records
Sound
Settings
key.
Phone
Settings
Select
In some functions, you may be asked for a
password or PIN. Enter the required code and
press the O K soft key.
3. To select the Phone Settings menu, press
the Select soft key or the
key.
Phone Settings
Infrared Activ...
My Settings
Greeting Me...
Own Number
Language
Security
4.1
Select
30
If the menu name is too
long for the display, it is
scrolled when highlighted.
31
Selecting Functions and Options
Phonebook
4. Scroll through the sub-menus until you reach
the Language sub-menu, by pressing the
or
key.
Phone Settings
Infrared Activ...
My Settings
Greeting Me...
Own N English
Language
Security
Select
4.5
Shows the
current setting
Storing a Number with a Name
5. To view the languages available, press the
Select soft key or the
key.
The current setting is highlighted.
There are two ways to store a number:
¥ Using the Save soft key in idle mode
¥ Using the New Entry option in the Phonebook
menu
Storing a Number in Idle mode
Language
English
Chinese S
Chinese T
You can store phone numbers and their
corresponding names in the memory of your SIM
card. In addition, you can store up to 500
numbers in the phone memory. The SIM card
and phone memories, although physically
separate, are used as if they were a single
entity, called the phonebook.
Current language
As soon as you start to enter a number, Save
appears above the left soft key to allow you to
store the number in the phonebook.
1. Key in the number to be stored.
Select
4.5.1
5. Scroll through the list of languages until the
appropriate one is highlighted, by pressing
the
or
key.
6. Press the Select soft key or the
confirm your selection.
7. Press the C or
structure.
32
key to
key twice to exit the menu
Note: If you make a mistake while entering a
number, correct it using the C key. For
further details, refer to page 22.
2. When you are sure that it is correct, press the
Save soft key.
3. Select an icon to identify the category of
number to be stored. Three categories are
available;
(mobile phone number),
(office number) and
(home number). To
select the category, press the
or key,
followed by the Select soft
33
Phonebook
Phonebook
4. Enter a name and press the O K soft key.
The maximum length of a name depends on
your SIM card. For information on how to
enter characters, see page 42.
The phone now displays the first free location
in the last memory used to save a number
and name. If that memory is full, the first
free location in the other memory is
displayed.
Note: If you change phones, any numbers
stored in your SIM card memory will
automatically be available with the new
phone, whereas any numbers stored in
the phone memory must be restored.
5. Press the right soft key, labelled To Card or
To Phone to toggle between the phone and
card memories.
6. If you do not want to save the number and
name in the suggested location, press the C
key to clear the location number and enter
your preferred location by pressing the
number keys.
7. Press the O K soft key to store the name and
number.
After storing, the phone displays the
phonebook entry or name just created.
8. To...
Use the entry
options
Return to the idle
screen
34
Press the...
Options soft key.
Storing a Number Using the
Phonebook Menu
1. When the idle screen is displayed, press the
N a m e soft key.
2. Scroll to New Entry by pressing the
key and press the Select soft key.
or
3. Select an icon to identify the category of the
number to be stored.
Note: The E-mail icon (
) is available in this
step. It allows you to save an E-mail
address instead of a phone number.
4. Continue the procedure from Step 4 on page
34 to store the number.
Using Phonebook Entry Options
While accessing any phonebook entry, press the
Options soft key to access the options for the
entry.
To...
Press the...
Select the
highlighted option
Select soft key or the
key.
Highlight a different
option
or
key until
the required option is
highlighted.
key.
35
Phonebook
The following options are available:
Paste: allows you to paste the selected number
into the normal dialling mode. Use this option to
dial a number similar to one in the phonebook, a
different extension in the same office, for
example.
Use the C key to change the number as
required; refer to page 22 for further details.
When you are ready to dial, press the
key.
Edit: allows you to edit the selected name and
number. Select One Entry to edit just the
currently selected entry. If you saved more than
one entry with a same name, All Entry allows
you to all corresponding entries.
Erase: allows you to erase the selected name
and number from the phonebook. You are asked
to confirm that you wish to erase the name and
number by pressing the Yes soft key.
C o p y: allows you to copy the selected number
to another location. Use this option to store a
number similar to one already in memory; once
copied, edit the number and store it in the
phonebook.
Caller Group: allows you to assign the entry to
a caller group so that the phone alerts you in a
particular way when the corresponding person
calls you. Select one of the ten groups available.
To remove an entry from a group, select the N o
Group option.
For more information on how to change caller
group properties, see page 39.
Add Entry: allows you to add a new number in
a different category (mobile, office, home or
E-mail) to the currently selected name. A
phonebook entry or name can contain up to four
number, one in each category.
36
Phonebook
Searching for a Number in the
Phonebook
After storing numbers in the phonebook, you can
search for them in two ways; by name and by
caller group.
Searching for a Number by Name
1. When the idle screen is displayed, press the
N a m e soft key.
2. Press the Select soft key when Search is
highlighted. You are asked to enter a name.
3. Enter the first few letters of the name that
you wish to find.
The phonebook entries are listed, starting
with the first entry matching your input. This
entry is also highlighted.
4. To...
Press the...
View the highlighted
entry
V i e w soft key.
Select a different
entry
or
key until
the required entry is
highlighted.
Look for a name
starting with a
different letter
Key labelled with the
required letter.
5. Once you have found the required entry,
press the
key to dial the number, or
press the Options soft key to access the
phonebook entry options; for further details,
see page 35.
37
Phonebook
Phonebook
Searching for a Number by Caller
Group
1. When the idle screen is displayed, press the
N a m e soft key.
2. Scroll to Group Search by pressing
or
key and press the Select soft key. You
are asked to enter a group name.
3. Enter the first few letters of the group name
that you wish to find.
The caller groups are listed, starting with the
first group matching your input. The group is
also highlighted.
4. Scroll to the required group by pressing the
or
key and press the V i e w soft key.
The phonebook entries in the selected caller
group are listed.
5. To...
Press the...
View the
highlighted entry
V i e w soft key.
Select a different
entry
or
key
until the required
entry is highlighted.
6. Once you have found the required entry,
press the
key to dial the number, or
press the Options soft key to access the
phonebook entry options; for further details,
see page 35.
38
Editing a Caller Group
1. When the idle screen is displayed, press the
N a m e soft key.
2. Scroll to Group Edit by pressing the
key and press the Select soft key.
or
3. Enter the first few letters of the required
group name or scroll through the group list by
pressing
or
key.
4. When the required group is highlighted, press
the Options soft key.
5. Select each option and change the settings,
as required. The following options are
available.
¥ Call ring tone: allows you to select the
ring tone to be used when you receive a
voice call from a person in the group.
¥ SMS tone: allows you to select the ring
tone to be used when you receive a text
message from a person in the group.
¥ Graphic: allows you to select the graphic
icon to be displayed when you receive a
voice call from a person in the group.
¥ G r o u p N a m e: allows you to assign a name
to the group; for further details on how to
enter characters, see page 42.
6. When you have finished, press the C or
key.
39
Phonebook
Phonebook
Speed-dialling
Once you have stored phone numbers in the SIM
card, you can set up to eight speed-dial entries
and then dial them easily whenever you want,
simply by pressing the associated number key.
¥ Erase All: allows you to clear the settings
for all keys so that no numbers are
assigned to any of the keys.
¥ N u m b e r: allows you to view the number
assigned to the key.
Setting Up Speed-dial Entries
7. When you have finished, press the C or
key.
1. When the idle screen is displayed, press the
N a m e soft key.
Speed-dialling from the Phonebook
2. Scroll to Speed Dial by pressing the
key and press the Select soft key.
To speed-dial the numbers assigned to keys 2 to
9 , press and hold down the appropriate key.
or
3. Select the key to which you wish to assign the
speed-dialling feature (keys 2 to 9 ) and press
the O K soft key.
Note: If you have already assigned a number to
the key, the Options soft key replaces
the O K soft key. Go to Step 6.
Note: Memory location 1 is reserved for your Voice
Mail server number.
Checking Memory Status
4. Select the required phonebook entry from the
list and press the V i e w soft key.
You can check how many names and numbers
are stored in the phonebook (card and phone
memories) or how many free locations remain.
5. Select the required number if the entry has
more than one number, by pressing the
or
key and press the Select soft key.
1. When the idle screen is displayed, press the
N a m e soft key.
6. Once you have assigned a number to the
selected key, four options are available:
¥ C h a n g e: allows you to assign a different
number to the key.
2. Select the Memory Status option.
3. Press the
or
key to view the number
of existing and remaining entries in the card
and phone memories.
¥ Erase: allows you to clear the setting so
that no number is assigned to the key.
40
41
Entering Text
Entering Text
Changing the Text Input Mode
The phone allows you to enter characters for
messages and names in Chinese and English. To
enter Chinese text, the phone provides several
widely used pronunciation based (Pinyin) and
character shape based (Stroke) input methods to
meet the preferences of different users, allowing
for greater convenience and ease of use.
You can also enter any combination of Chinese
characters, alphabets, numbers, and special
symbols including punctuation marks.
When you are in a field that allows characters to
be entered, you will notice the text input mode
indicator on the display.
Example: Entering a name for a phonebook
entry
Enter Name
The following text input modes are available on
your phone:
¥ Pinyin mode
¥ Chinese Simplified Stroke mode
OK
PY Mode
Text input mode
indicator
¥ Quick English mode
¥ English mode
¥ Chinese Traditional Stroke mode
¥ Number mode
You can change between Chinese and English
input methods or to numbers input. To change to
another text input mode:
1. Press the right soft key, labelled with the
current mode.
¥ Symbolic mode
¥ Help mode
Directions for using each of the text input modes
appear later in this section.
2. Scroll to the desired mode with the
keys.
and
Input Mode
Pinyin
CHN S Stroke
Quick English
English
CHN T Stroke
Number
Confirm
2/8
3. To select the displayed mode, press the
Confirm soft key.
42
43
Entering Text
Entering Text
Note: If you want to exit the menu without
changing to a new mode, press the right soft
key.
4. You will find the selected text input mode
indicator at the bottom of the display.
Enter Name
Using the Chinese Pinyin Mode
Pinyin is a system to mark Chinese
pronunciation in Latin alphabets. With the pinyin
input method, you can enter Chinese characters
by keying in the pinyin string from the phone
keypad and the phone automatically presents
the matching alternatives.
This mode allows you to enter Pinyin characters
with only one key press per letter.
Typing Characters in Pinyin Mode
OK
S STR
¥ Chinese Pinyin mode → PY Mode
1. Press keys corresponding to the phonetic
spelling, referring to the alphabets printed on
the keys. Notice that the choices in the
Character Selection Map change.
¥ Chinese Simplified Stroke mode → S STR
Example: Typing
¥ Quick English mode →
in Pinyin mode
ENG
¥ English mode → A B C
¥ Chinese Traditional Stroke mode → T STR
Enter Name
¥ Number mode → N U M
¥ Symbolic mode → SYM Mode
¥ Help mode → HELP Mode
OK
PY Mode
Key Stroke Area
Press the 5 key and the
4 key to enter li.
Character Selection Map
2. If you cannot find the character on the
display, scroll through choices in the
Character Selection map by pressing the
key. To move back, press the
key.
When the character you are typing appears in
the Character Selection Map, you may select
it, without completing the Pinyin spelling for
the character.
44
45
Entering Text
Entering Text
3. To select a character, press the 1 key to
activate the Character Selection Map. A
number (7 to
) is added to the beginning of
a corresponding character. With the Character
Selection Map being activated, a normal press
on the 7 key to the key selects the
corresponding character.
Enter Name
OK
PY Mode
Press the 0 key to select
Rapid Character Entry
Rapid character entry is easy in any mode, using
the Character Selection Map. As you enter
characters, your phone predicts the next
character you might want and presents choices
in the Character Selection Map area. When a
desired character appears, you may select it as
described in Step 3 on page 46.
For example, if you want to type the word
zhong guo (
) and entered the first
character using the following keystrokes; 9, 4, 6,
6, 1 and 7, you don t need to complete the
Pinyin spelling to include guo ( ). With no
extra typing, the character is displayed
conveniently in the Character Selection Map for
you to choose.
Inserting a Space
To insert a space between characters, press the
key when the cursor blinks in the Text Area.
Scrolling
To move the cursor to the left or to the right
through your text message, press the
or
key.
Clearing Strokes and Characters
Press the C key one or more times to remove
key stokes to the left. When the Key Stroke Area
is empty, pressing the C key removes characters
from the Text Area.
46
Using the Chinese Stroke Mode
This mode allows you to enter individual Chinese
strokes, in written order, from top to bottom and
from left to right. Your phone provides Chinese
Simplified Stroke mode and Chinese Traditional
Stroke mode.
The two modes work similarly, but the
characters that appear on the display may differ.
Even though there are many different strokes
used to create Chinese characters, the strokes
are classified into 5 basic categories; heng, shu,
pie, dian and zhe. The basic strokes are printed
on the keypad, on the keys 1 to 5 .
To enter a stroke, press the key printed with the
stroke that most closely represents the exact
stroke you desire.
47
Entering Text
Entering Text
The table shows the stroke/key relationship:
Categories
Keys
Strokes Represented in Each Categor
2. The phone displays your strokes in the Key
Stroke Area and offers character choices in
the Character Selection Map. As you enter
strokes, notice that the choices in the
Character Selection Map change. To scroll
through choices in the Character Selection
M a p, press the
key. To move back, press
the
key.
3. When the character you are typing appears in
the Character Selection Map, you may select
it without finishing the stroke sequence for
the character. Characters displayed in the
Character Selection Map correspond to the
keys 7 to
on the keypad. To select a
character from the Character Selection Map
and add it to your message, press the
corresponding key (7 to
).
Typing Stokes and Characters in
Stroke Mode
1. To type a character, press keys corresponding
to its component strokes. Press keys on the
phone in order that you would write the
strokes, using one press per desired stroke.
Example: Typing
in Chinese Simplified
Stroke mode
Note: If you are uncertain of the order of one or
more strokes, press the 6 key in place of
each questionable stroke. Continue entering
strokes until the character is displayed in the
Character Selection Map or until you finish
the character.
Inserting a Space
To insert a space between characters, press the
key when the cursor blinks in the Text Area.
Enter Name
Scrolling
OK
STR Mode
Key Stroke Area
Press the 5 key and the
3 key to enter
Character Selection Map
Press the 7 key to select
48
To move the cursor to the left or to the right
through your text message, press the
or
key.
49
Entering Text
Clearing Letters and Words
Entering Text
1. Press keys on the phone just once per desired
letter. For example, to enter HELLO , press
Press the C key one or more times to remove
strokes to the left. When the Key Stroke Area is
empty, pressing the C key removes characters
from the Text Area.
Rapid Character Entry
Rapid character entry is easy in any mode, using
the Character Selection Map. As you enter
characters, your phone predicts the next
character you might want and presents choices
in the Character Selection Map area. When a
desired character appears, you may select it as
described in Step 3 on page 49.
and
2. Type to the end of the word before editing or
deleting any keystrokes.
3. If the word is correct, put a space by pressing
the key and start entering the next word.
Otherwise, press the 0 ,
or
key
repeatedly to display alternate word choices
for the keys that you pressed.
In most cases, you will see the desired character
in the Character Selection Map area before you
have entered all of the strokes to build it.
For example, try typing the twelve stroke
character pair
using the following
keystrokes; 2, 8, and 7. Even though
is a
twelve stroke character pair, your phone enables
you to type it in only three key presses!
The word that you are typing appears on the
display. It may change with each key that you
press.
Example: Both OF and ME have the
sequence of 6 and 3 . The phone displays the
most commonly used choice first.
To type words not found in the Quick English
mode, change the text input mode to English.
Smart Punctuation
Using the Quick English Mode
This mode allows you to enter English words
with only one key press per letter. Each key on a
keypad has more than one letter - a single press
on the 5 key could be J, K, or L. The Quick
English mode automatically compares your key
presses to an internal linguistic database to
determine the correct word.
The mode requires far fewer keystrokes than the
traditional multi-tap method, English mode.
50
To enter full stops, hyphens or apostrophes,
press the 1 key. The Quick English mode applies
grammar rules to ensure that the correct
punctuation is used.
Example: The 1 key is used twice to display two
punctuation marks:
51
Entering Text
Changing the Case
To change the case of the letters, use the
key. The Capital Lock mode is indicated by
and the Small Caps mode is indicated by .
Entering Text
Refer to the table below for more information
about the characters available in the English
mode.
Characters in the Order Displayed
Key
Upper Case
Scrolling
You can move the cursor through the text by
using the
and
keys.
Lower Case
Space
Clearing Letters and Words
To delete letters, press the C key. Press and hold
down the C key to clear the display.
Using the English Mode
When typing in the English mode, you should
press key labelled with the required character:
-Once for the first character
-Twice for the second character
and so on.
For example, you need to press the 2 key three
times to display the character C and the 5 key
two times to display the character K. For this
reason, this method is called Multi-tap typing.
The cursor moves to the right when you press a
different key. When entering the same letter
twice or a different letter on the same key, just
w ait for a few seconds for the cursor to move to
the right automatically, and then select the next
letter.
Changing the Case
To change the case of the letters, use the
key. The Capital Lock mode is indicated by
and the Small Caps mode is indicated by .
Scrolling
You can move the cursor through the text by
using the
and
keys.
Clearing Letters and Words
To delete letters, press the C key. Press and hold
down the C key to clear the display.
You can put a space between each word by
pressing the
key.
52
53
Entering Text
Options During a Call
Using the Number Mode
The Number mode enables you to enter numbers
in a text message (a telephone number for
example). Press the keys corresponding to the
required digits before manually switching back to
the appropriate text input mode.
Using the Symbolic Mode
The symbol mode enables you to insert symbols
in a text message.
Symbolic
Your phone provides a number of control
functions that you can use during a call.
Putting a Call on Hold
You can place the current call on hold whenever
you want. You can make another call while you
have a call in progress if this service is
supported by the network. Of these two calls,
one is active and the other is on hold and you
can switch between the calls.
To place a call on hold, simply press the Hold
soft key. You can reactivate the call whenever
you want, by pressing the Unhold soft key.
To make a call while you have a call in progress:
1. Enter the phone number that you wish to dial
or look it up in the phonebook.
OK
SYM Mode
Use the navigation keys to scroll to the desired
symbol and then press the O K soft key to insert
the highlighted symbol into your message.
2. Press the
key to dial the second call.
The first call is automatically put on hold.
Or alternatively:
1. Put the current call on hold by pressing the
Hold soft key.
2. M a ke the second call in the normal way.
Using Help
To switch between the two calls, simply press
the S w a p soft key.
On-screen help is available by selecting Help
from the Input Mode menu. Use the
and
keys to scroll through the Help information.
The current call is placed on hold and the call on
hold is reactivated so that you can continue
conversing with the other party.
When you have finished, end each call normally
by pressing the
key.
54
55
Options During a Call
Options During a Call
Switching the Microphone Off
(Mute)
You can temporarily switch your phone s
microphone off, so that the other party cannot
hear you.
Example: You wish to say something to another
person in the room but do not want
the other party to hear you.
Muting/Sending Key Tones
These options allow you to turn the key tones off
or on. If the Mute keys option is selected, your
phone does not transmit the key tones. It allows
you to press keys without hearing annoying key
tones during a call.
Note: To communicate with answering machines or
computerised telephony systems, the S e n d
keys option must be selected.
To switch the microphone off temporarily:
1. Press the Options soft key.
2. If necessary, press the
the M u t e option.
key to highlight
Searching for a Number in the
Phonebook
3. Press the O K soft key.
The other party can no longer hear you.
You can search for a number in the phonebook
during a call.
To switch the microphone back on:
1. Press the Options soft key.
1. Press the Options soft key.
2. Press the
key to highlight the
P h o n e b o o k option.
2. If necessary, press the
the U n m u t e option.
key to highlight
3. Press the O K soft key.
The other party can hear you again.
3. Press the O K soft key.
The phonebook entries are listed.
4. Enter the name that you wish to find.
If you enter the first few letters of the name,
the phonebook entries are listed, starting
with the first entry matching your input. The
entry is also highlighted.
5. To view the highlighted entry, press the V i e w
soft key.
For a more detailed description of the Phonebook
feature, refer to page 33.
56
57
Options During a Call
Options During a Call
Using the SMS Service
Making a Multiparty Call
If you receive an SMS (Short Message Service)
message during a call, the message icon (
flashes on the display. The SMS Service option
enables you to use this feature.
A multiparty call is a network service that allows
up to six people to take part simultaneously in a
multiparty or conference call. For more
information, contact your service provider.
Read Messages: allows you to read the
messages that you have received.
Setting up the Multiparty Call
Write Messages: allows you to write a
message.
1. Call the first participant in the normal way.
For further details on the SMS service, refer to
page 60.
2. Call the second participant in the normal way.
The first call is automatically put on hold.
3. To join the first participant to the multiparty
call, press the Options soft key and select
the Join option.
Answering a Second Call
You can answer an incoming call while you have
a call in progress, if this service is supported by
the network and you have set the Call Waiting
menu option (Menu 6.3) to Activate (see page
99). You will be notified of an incoming call by a
call waiting tone.
4. To add a new person to the multiparty call,
call the person in the normal way, then press
the Options soft key and select the Join
option.
You can add incoming callers by answering the
call and pressing Options, followed by Join.
Repeat as required.
To answer a call while you have a call in:
1. Press the
call.
key to answer the incoming
The first call is automatically put on hold.
2. To switch between the two calls, press the
S w a p soft key.
To end a held call, press the Options soft key
and select the End Held Call option.
3. To end the current call, press the
58
key.
Having a Private Conversation With
One Participant
1. Press the Options soft key and choose the
Select one option.
The list of the call participants appears.
2. Highlight the required person, by pressing the
or
key, followed by the Select soft
key or the
key.
59
Options During a Call
Using the Menus
3. Select the Private option.
Now you can talk privately with that person.
The other participants can continue to
converse with each other.
4. To return to the multiparty call, press the
Options soft key and select Join.
All the multiparty call participants can now
hear each other.
Dropping One Participant
1. Press the Options soft key and choose the
Select one option.
The list of call participants appears.
2. Highlight the required person, by pressing the
or
key, followed by the Select soft
key or the key.
3. Select R e m o v e.
The call is ended with that participant, but
you can continue to talk with the other
participants.
4. End the multiparty call by closing the phone
or pressing the
key.
The phone offers a range of functions that allow
you to tailor the phone to your needs. These
functions are arranged in menus and sub-menus.
The menus and sub-menus can be accessed by
scrolling with the navigation keys or by using the
shortcuts.
Accessing Menu Functions by Scrolling
1. In idle mode, press the M e n u soft key to
access menu mode.
2. Scroll with the
or
key to reach the
required main menu, Phone Settings for
example. Press the Select soft key or the key
to enter the menu.
3. If the menu contains any sub-menus,
Language for example, you can access them
by scrolling with the
or
key and
pressing the Select soft key.
If the menu that you have selected contains
further options, repeat the same procedure.
4. To...
or
key or use
the
and
keys on
the left side of the
phone.
Confirm the chosen
setting
Select soft key or
the
key.
Return to the
previous menu level
soft key or the
key.
Exit the menu
without changing
the settings
60
Press the...
Scroll through the
menus
key.
61
Using the Menus
Accessing Menu Functions by Using
Shortcuts
The menu items (menu, sub-menus and options)
are numbered and can be accessed quickly by
using their shortcut number. The shortcut
number is shown in the bottom right next to the
soft key on the display. Simply press the M e n u
soft key and key in the required number.
Example: Accessing the Language option.
1. Press the M e n u soft key.
2. Press
for Phone Settings.
3. Press
for Language.
The languages available are displayed
directly.
Note: The numbers assigned to each menu option
are indicated in the list on page 55. They
m ay not match the menu number on the
phone. It depends on the services supported
by the SIM card.
List of Menu Functions
The following illustration shows the menu
structure available and indicates the:
Number assigned to each option
Page on which you can find a description of each
feature
Note: If you use a SIM AT card that provides
additional services, the SIM AT menu (8) is
displayed first when you press the M e n u
soft key to enter the menu facility. For
further details, refer to your SIM card
documentation.
62
Using the Menus
1. Messages (see page 60)
1.1 Read Messages
1.1.1 Inbox
1.1.2 Outbox
1.2 Write Messages
1.3 Templates
1.4 Setup
1.4.1 Setting 1*
1.4.2 Setting 2*
1.4.3 Setting 3*
1.4.4 Common Setting
1.5 Broadcast
1.5.1 Read
1.5.2 Receive
1.5.3 Channel List
1.5.4 Language
1.6 Voice Mail
1.6.1 Connect to Voice Server
1.6.2 Voice Server Number
1.7 My Contents
1.7.1 My EMS Melody
1.7.2 My EMS Picture
1.7.3 My EMS Animation
1.8 Memory Status
1.8.1 SIM memory
1.8.2 PHONE memory
1.8.3 CB memory
2. Call Records (see page 69)
2.1
2.2
2.3
2.4
Missed Calls
Received Calls
Dialled Calls
Call Time
2.4.1 Last Call Time
2.4.2 Total Sent
2.4.3 Total Received
2.4.4 Reset Timers
* Shown only if supported by your SIM card.
63
Using the Menus
Using the Menus
2. Call Records (continued)
2.5 Call Cost
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
Last Call Cost
Total Cost
Max Cost
Reset Counters
Set Max Cost
Price/Unit
3. Sound Settings (see page 72)
3.1
3.2
3.3
3.4
3.5
Ring Tone
Ring Volume
Alert Type
Keypad Tone
Message Tone
3.5.1 SMS Tone
3.5.2 SMS-CB Tone
3.6 Extra Tones
3.6.1 Error Tone
3.6.2 Minute Minder
3.6.3 Connect Tone
4. Phone Settings (see page 76)
4.1 Infrared Activate
4.2 My Settings
4.2.1 Wallpaper
4.2.2 Colour Theme
4.2.3 Menu Style
4.3 Greeting Message
4.4 Own Number
4.5 Language
4.6 Security
4.6.1 PIN Check
4.6.2 Change PIN
4.6.3 Phone Lock
4.6.4 Change Password
4.6.5 SIM Lock
4.6.6 FDN Mode*
4.6.7 Change PIN2*
* Shown only if supported by your SIM card.
64
4. Phone Settings (continued)
4.7 Display Settings
4.7.1 Contrast
4.7.2 Back Light
4.7.3 Auto Light
4.7.4 Service Light
4.7.5 Graphic Logo
4.8 Extra Settings
4.8.1 Auto Redial
4.8.2 Active Flip
4.8.3 Anykey Answer
4.9 Short Cut
4.10 Reset Settings
5. Organiser (see page 86)
5.1 Calendar
5.2 To Do List
5.3 Time & Date
5.3.1 Set Time
5.3.2 Set Date
5.3.3 World Time
5.3.4 Time Format
5.4 Alarm
5.5 Calculator
5.6 Currency Exchange
6. Network Services (see page 95)
6.1 Call Diverting
6.1.1 Divert Always
6.1.2 Busy
6.1.3 No Reply
6.1.4 Unreachable
6.1.5 Cancel All
6.2 Call Barring
6.2.1 All Outgoing
6.2.2 International
6.2.3 International Except to
Home
6.2.4 All Incoming
6.2.5 Incoming While Abroad
6.2.6 Cancel All
6.2.7 Change Barring Password
65
Using the Menus
Messages
6. Network Services (continued)
6.3 Call Waiting
6.3.1 Voice Calls
6.3.2 Data Calls
6.3.3 Cancel All
6.4 Network Selection
6.4.1 Automatic
6.4.2 Manual
6.5 Caller ID
6.5.1 Default
6.5.2 Hide Number
6.5.3 Send Number
6.6 Closed User Group
6.6.1 Index List
6.6.2 Outside Access
6.6.3 Default Group
6.6.4 Deactivate*
6.7 Band Selection
The SMS (Short Message Service) function is a
network service and may not be supported by
your network. Messages can be sent by text,
fax, Email and paging messaging systems,
provided that these services are supported by
your network. To send text messages by phone,
you must obtain the number of the SMS centre
from your service provider.
When the message icon (
) appears, you have
received new text messages. If the message
memory is full, an error message is displayed
and you cannot receive any new messages. Use
the Delete option in the Read Messages m e n u
(Menu 1.1) to delete obsolete messages.
7. Funbox (see page 104)
7.1 Games
7.2 WAP Browser
7.3 Downloads
7.3.1 Games & More
7.3.2 Sounds
7.3.3 Pictures
7.3.4 Settings
Read Messages
(Menu 1.1)
Two message boxes are available.
Inbox: used to store the messages that you
have received.
Outbox: used to store the messages that you
have already sent or will send.
Reading a Message
1. Select the required box and press the Select
soft key.
The list of messages in the box is displayed
with the sender or recipient s phone number
or name, if it is available in your phonebook.
* Shown only if the Close User Group feature is active.
66
2. Select the required message and press the
V i e w soft key to view the message contents.
67
Messages
3. To scroll through the message, press the
or
key.
While reading a message, you can choose the
following options by pressing the Options soft
key:
Delete: allows you to delete obsolete messages.
Text Reply (inbox only): allows you to reply to
the sender by sending a text message. You can
also change the SMS centre number, if required.
Call Back (inbox only): allows you to call the
sender back.
Cut Number: allows you to extract a number
from the message text, so that you can call the
number or save it in the phonebook.
S e n d: allows you to send a message that you
have received or saved. For further information
on how to send a message, see page 69.
Messages
Write Messages
(Menu 1.2)
Via this menu, you can write and send a text
message.
Note: If you add items to the message, the
number of the characters you can enter will
be decreased.
Creating a Simple Text Message
1. Create your message.
Note: For more information about entering
characters, refer to page 42.
2. When you have completed your message,
press the Options soft key. The following
options are available:
¥ Send Only: allows you to send the
message. The message will be deleted after
sending.
Edit Message: allows you to edit a message.
Select Objects: allows you to save the objects,
such as sounds or images, from the message
into your phone. You can then use the objects
when writing a message; for details, see page
69.
Note: The options available vary, depending on the
message status (new/old, not sent or sent
for example).
¥ Save and Send: allows you to save a copy
of the message and then send the message
to the required destination. You can read
the message in your outbox using the R e a d
Messages option.
¥ Save Only: allows you to save the
message so that it can be sent later. You
can read the message in your outbox using
the Read Messages option.
¥ Add Objects: allows you to add the
required sound, picture or animation to the
message. Select the category of the object
to be added; S o u n d, Melody, Picture and
Animation are available. In each category,
you can select various factory-set items or
choose items received from other sources,
such as the Internet or other phones.
68
69
Messages
¥ Add Templates: allows you to apply one of
the preset message templates to the text.
Select one of the five messages predefined
via the Templates menu option (M e n u
1.3); for further details, see page 78.
3. When you finish entering your message, press
the Options soft key and select Send Only
or Save and Send.
If you want just to save the message, select
Save Only. After saving the message, the
phone returns to the Messages menu.
4. Enter a destination number.
Pressing the N a m e soft key when it is
displayed allows you to search the Phonebook
for a number.
5. Press the O K soft key. The message is sent.
Messages
Templates
(Menu 1.3)
Using this menu, you can preset up to five
messages that you use most frequently. Scroll
through the template list using the
and
keys. When the required message template is
highlighted, press the Options soft key.
Edit: allows you to write a new message or edit
the selected message.
Note: For further information on how to enter
characters, refer to page 42.
Send Message: allows you to recall the
selected message. Once you have completed the
message, you can send, save and send, or
simply save it. For details on how to send a
message, see page 69.
Delete: allows you to delete the selected
message. You are asked to confirm the deletion
by pressing the Yes soft key.
Setup
(Menu 1.4)
Via this menu, you can set up default SMS
information. A setting group is a collection of
settings required to send messages. The number
of setting groups available depends on the
capacity of your SIM card.
Setting x (where x is the setting group
number): each group has its own sub-menu.
Service Centre: allows you to store or change
the number of your SMS centre required when
sending messages. You must obtain this number
from your service provider.
70
71
Messages
Default Type: allows you to set the default
message type (Text, Fax, Email and Paging). The
network can convert the messages into the
selected format.
Default Validity: allows you to set the length of
time for which your text messages will be stored
at the message centre while attempts are made
to deliver them.
Setting Name: allows you to give a name to the
setting group currently being defined.
Messages
Broadcast
(Menu 1.5)
This network service allows you to receive text
messages on various topics, such as the weather
or traffic. Messages are displayed immediately
they are received, provided that:
¥ The phone is in idle mode
¥ The Receive option is set to Enable
¥ The message channel is currently active in the
channel list
The following options are available:
Common Setting: four options are available.
Reply Path: allows the recipient of your SMS
message to send you a reply message via your
message centre, if the service is provided by the
network.
Delivery Reports: allows you to activate or
deactivate the report function. When this
function is activated, the network informs you
whether your message has been delivered or
not.
R e a d: lets you view the message. Volatile
displays the messages from the network, but
loses its contents as soon as the phone is
switched off. Scroll through the message by
using the and keys. While reading a message,
press the Save soft key to store the message in
the Archive box for later retrieval.
Receive: allows you to enable or disable the
reception of broadcast messages.
Bearer Selection: allows you to choose between
G S M and G P R S.
Channel List: allows you to indicate the
channels from which you wish to receive
broadcast messages. The following options are
available:
W ap Push: allows you to select whether you
receive Web messages from the server or not.
Select Never if you do not want to receive any
messages, Always to receive all messages, and
SMS-C Specific to receive messages from a
specific SMS centre.
Select: used to enable or disable channels in the
list by marking or unmarking them respectively
(a check mark is displayed in front of each
channel selected).
Add Channel: used to declare the ID and title for
a new channel.
Delete: used to remove a channel from the list.
Edit: used to change the ID and title of an
existing channel.
72
73
Messages
Messages
Language: allows you to select your preferred
language to be used when displaying cell
broadcast messages.
My Contents
(Menu 1.7)
Please contact your service provider for more
information.
After saving any objects received in messages
into your phone memory, using the Select
Object option (see page 68), you can see the
objects in this menu.
Voice Mail
To delete the objects in this menu, press the
Delete soft key.
(Menu 1.6)
This menu provides you with a way of accessing
your voice mailbox (if provided by your
network).
The following options are available:
Connect to Voice Server: before using this
feature, you must enter the voice server number
obtained from your service provider (see menu
option 1.6.2). You can then select this option
and simply press the O K soft key to listen to
your messages.
To quickly connect to the voice server, press and
hold down the 1 key in idle mode.
You can forward the objects to other people by
including message and/or use them for your ring
tone or background them in a image.
Three categories of objects are available:
¥ My EMS Melody
¥ My EMS Picture
¥ My EMS Animation
Memory Status
(Menu 1.8)
This menu shows how many messages are
currently stored in the SIM, phone and CB
memories.
Voice Server Number: allows you to change
the voice mail server number, if necessary.
To...
Press the...
Enter the server
number
Corresponding
numeric keys.
Correct a digit
C key.
M ove the cursor to
the left/right without
clearing the digit
or
key.
Note: Voice Mail is a network feature. Please
contact your service provider for more
information.
74
75
Call Records
Call Records
Via this menu, you can view the:
¥ missed, received or dialled phone calls.
¥ length of the calls you made or received.
¥ cost of the calls you made.
Dialled Calls
(Menu 2.3)
This option lets you view the last 20 numbers
dialled.
Note: You can access all numbers in the three
types of call records by pressing the
key in idle mode.
The number and name, if available, are
displayed, together with the date and time at
which the call was made. By pressing the
Options soft key, you can:
Missed Calls
¥ Delete the call from the list
¥ Edit the number if available and dial it or save
it in the phonebook
(Menu 2.1)
This option lets you view the last 20 unanswered
calls.
The number and name, if available, are
displayed, together with the date and time at
which the call was received. By pressing the
Options soft key, you can:
Call Time
(Menu 2.4)
This option lets you view the timers for calls
made and received.
The following timers are available:
¥ Delete the call from the list
¥ Edit the number if available and dial it or save
it in the phonebook
Last Call Time: the length of the last call.
Received Calls
Total Received: the total length of all calls
received since the timer was last reset.
(Menu 2.2)
This option lets you view the last 20 phone calls
answered.
The number and name, if available, are
displayed, together with the date and time at
which the call was received. By pressing the
Options soft key, you can:
¥ Delete the call from the list
¥ Edit the number if available and dial it or save
it in the phonebook
76
Total Sent: the total length of all calls made
since the timer was last reset.
Reset Timers: the option used to reset the call
timers; you must first enter the phone password
(see page 117) and then press the O K soft key.
Note: The actual time invoiced for calls by your
service provider may vary, depending on
network features, rounding-off for billing
purposes and so on.
77
Call Records
Sound Settings
Call Cost
(Menu 2.5)
This network feature lets you view the cost of
calls.
The following options are available:
Last Call Cost: cost of the last call made.
Total Cost: total cost of all calls made since the
cost counter was last reset. If the total cost
exceeds the maximum cost set via the Set Max
Cost option, you can no longer make any calls
until you reset the counter.
Max Cost: maximum cost set via the Set Max
Cost option (see below).
Reset Counters: option used to reset the cost
counter; you must first enter your PIN2 (see
page 119) and then press the O K soft key.
Set Max Cost: option used to enter the
maximum cost that you authorise for your calls.
Price/Unit: option used to set the cost of one
unit; this price per unit is applied when
calculating the cost of your calls.
You can use the Sound Settings feature to
customise various settings, such as the:
¥ Ring melody, volume and type
¥ Sounds made when you press a key, make an
error or receive a message
Note: When the phone is in the silent mode (see
page 28), you cannot change the sound
settings.
Ring Tone
(Menu 3.1)
This option allows you to select the required ring
melody.
You can choose between many different
melodies. Each time you select a melody, it is
played for a few seconds. If you have
downloaded any sounds from the Internet or
EasyGPRS programme or received any ring tone
messages, you can view the list in this menu.
Ring Volume
(Menu 3.2)
This option allows you to adjust the ring volume
to one of five levels.
Use the
and
keys or the
on the left side of the phone.
78
and
keys
79
Sound Settings
Alert Type
Sound Settings
(Menu 3.3)
This option allows you to specify how you are to
be informed of any incoming calls.
Message Tone
(Menu 3.5)
This option allows you to select how the phone
informs you that a new message has been
received.
The following options are available:
Light only: only the backlight is switched on;
the phone neither rings nor vibrates.
Melody: the phone rings using the ring melody
selected via the Ring Tone menu option (M e n u
3.1); see page 79.
SMS Tone
This option allows you to select how the phone
informs you that a new SMS message has been
received.
The following options are available:
Vibration: the phone vibrates but does not ring.
O F F: the phone does not use the SMS tone.
Vibra+Melody: the phone first vibrates three
times and then starts ringing.
Light Only: the service light at the top of the
phone flashes.
Vibration: the phone vibrates.
Keypad Tone
(Menu 3.4)
This option allows you to select the tone that the
keypad generates when you press a key.
The following options are available:
O F F: the keys do not make any sound.
T o n e: each key, when pressed, makes a
different sound.
Single Beep: the phone beeps once.
SMS Tone1~ 1 0: the phone uses an SMS tone.
You are provided with ten SMS tones.
SMS-CB Tone
This option allows you to select how the phone
informs you that a new cell broadcast (CB)
message has been received.
The following options are available:
B e e p: each key, when pressed, makes the same
sound.
O F F: the phone does not use the CB tone.
Light Only: the service light at the top of the
phone flashes.
Vibration: the phone vibrates.
Single Beep: the phone beeps once.
SMS-CB Tone1~ 1 0: the phone uses a CB tone.
You are provided with ten CB tones.
80
81
Sound Settings
Phone Settings
Extra Tones
(Menu 3.6)
You can customise various other tones used by
the phone.
To turn a
given tone...
Press the...
On
OK soft key.
A check mark is displayed in
front of the option.
M a ny different features of your phone can be
customised to suit your preferences. All of these
features are accessed via the Phone Settings
menu.
Infrared Activate
O K soft key again. The check
mark is no longer displayed.
The following options are available:
Error Tone: sets whether the phone informs
you that you have made a mistake or not.
Minute Minder: sets whether the phone must
beep every minute during an outgoing call to
keep you informed of the length of your call.
Connect Tone: sets your phone to beep when
the person you are calling answers the phone.
This feature allows you to send or receive
data/fax through the infrared port. To use an
infrared connection, you must:
¥ Configure and activate an IrDA-compliant
infrared port on your PC
¥ Activate the infrared feature on the phone; the
IrDA icon ( ) appears on the top line of the
display
¥ Align the IrDA port on the phone with the IrDA
port on your computer
IrDA port
15
Off
(Menu 4.1)
IrDA port
The connection is ready for data transmission.
If there is no communication between your
phone and the IrDA-compliant device within 30
seconds of activating the feature, it is
automatically deactivated.
Note: For best performance, it is highly
recommended that you use the data link
cable supplied in your SGH-S108 kit.
82
83
Phone Settings
My Settings
Phone Settings
(Menu 4.2)
Menu Style
You can change the background image and the
colour of the components in the display
according to your preference.
This option allows you to select the menu display
style. You can choose between Folder Style and
Nature Style.
Wallpaper
Greeting Message
This option allows you to change the background
image (wallpaper) to be displayed in idle mode.
To change the background image:
1. Scroll through the list by pressing the
key.
or
You have various preset images available. You
can also select the blank background and any
images downloaded from the Internet or the
EasyGPRS programme.
2. Press the Select soft key when the required
image is highlighted.
(Menu 4.3)
This option allows you to set a greeting message
to be displayed briefly when the phone is
switched on. The current message is displayed.
To...
Press the...
Clear the existing
message
C key and hold it down
until the message is
cleared.
Enter a new
message
Appropriate
alphanumeric keys.
Change the text
input mode
right soft key labelled with
the current input mode
The selected image is displayed.
3. After viewing the image, press the Select soft
key to display it on the idle screen.
For further details on how to enter characters,
refer to page 42.
Colour Theme
Own Number
You can change the colour setting of the display
components, such as text, soft key display area
or the menu names and icons. Nine different
colour settings are available.
This feature allows you to:
¥ Assign a name to each of your own phone
numbers registered on your SIM card
¥ Edit the names and numbers
Select the required setting and press the Select
soft key, followed by O K to confirm the highlight
colour and colour theme.
This function is a memory aid, which you can
use to check your own phone numbers if you
need to do so.
(Menu 4.4)
A ny changes made here do not in any way affect
the actual subscriber numbers on your SIM card.
84
85
Phone Settings
Language
Phone Settings
(Menu 4.5)
You can select a display language. English,
Chinese S (Simplified Chinese) and Chinese T
(Traditional Chinese) are available.
Change PIN
This feature allows you to change your current
PIN to a new one, provided that the PIN Check
feature is enabled. You must enter the current
PIN before you can specify a new one.
Note: This setting doesn t affect the WAP browser.
Once you have entered a new PIN, you are
asked to confirm it by entering it again.
Security
(Menu 4.6)
Phone Lock
The Security feature enables you to restrict the
use of your phone to:
¥ the people of your choice
¥ the types of calls of your choice
Various codes and passwords are used to protect
the features of your phone. They are described in
the following sections (see also pages 110-113).
When the Phone Lock feature is enabled, the
phone is locked and you must enter the 8-digit
phone password each time the phone is switched
on.
The password is factory set to 00000000. To
change the phone password, refer to the
Change Password menu option (Menu 4.6.4)
below.
PIN Check
When the PIN (Personal Identification Number)
Check feature is enabled, you must enter your
PIN each time you switch the phone on.
Consequently, any person who does not have
your PIN cannot use your phone without your
approval.
Note: Before disabling the PIN Check feature, you
must enter your PIN.
To change your PIN, refer to the Change PIN
menu option (Menu 4.6.2).
The following options are available:
Disable: the phone connects directly to the
network when you switch it on.
Enable: you must enter the PIN each time the
phone is switched on.
86
Once the correct password has been entered,
you can use the phone until you switch it off.
The following options are available:
Disable: you are not asked to enter the phone
password when you switch the phone on.
Enable: you are required to enter the phone
password when you switch the phone on.
Change Password
The Change Password feature allows you to
change your current phone password to a new
one. You must enter the current password before
you can specify a new one.
The password is factory set to 00000000. Once
you have entered a new password, you are
asked to confirm it by entering it again.
87
Phone Settings
SIM Lock
Phone Settings
Display Settings
(Menu 4.7)
When the SIM Lock feature is enabled, your
phone only works with the current SIM. You
must enter the SIM lock code.
Contrast
Once you have entered the lock code, you are
asked to confirm it by entering it again.
This option allows you to adjust the contrast of
the display screens to make them lighter or
darker.
To unlock the SIM, you must enter the SIM lock
code.
To adjust the display contrast:
FDN Mode
The FDN (Fixed Dial Number) mode, if supported
by your SIM card, allows you to restrict your
outgoing calls to a limited set of phone numbers.
The following options are available:
Disable: you can phone any number.
1. Select the required display (Main LCD or
Front LCD) and press the Select soft key.
2. Adjust the contrast by using the
and
keys or the
and
keys on the left side of
the phone.
3. When you are satisfied, press the O K soft key
to save the selection.
Enable: you can only call phone numbers stored
in the phonebook. You must enter your PIN2.
Back Light
Note: Not all SIM cards have a PIN2. If your SIM
card does not, this menu option is not
displayed.
To change your PIN2, refer to the Change PIN2
menu option (Menu 4.6.7) below.
You can select whether or not the phone uses
the backlight. A marginal increase in
standby/talk time can be achieved by turning the
backlight off.
The following options are available:
Change PIN2
O F F: the backlight is not used.
The Change PIN2 feature allows you to change
your current PIN2 to a new one. You must enter
the current PIN2 before you can specify a new
one.
Short: the backlight comes on when you press a
key or receive a call and switches off 10 seconds
after the last key is pressed.
Once you have entered a new PIN2, you are
asked to confirm it by entering it again.
L o n g: the backlight comes on when you press a
key or receive a call and switches off 20 seconds
after the last key is pressed.
Note: Not all SIM cards have a PIN2. If your SIM
card does not, this menu option is not
displayed.
88
89
Phone Settings
Phone Settings
Auto Light
Extra Settings
Using this feature, you can specify the time for
which the backlight is to be used. This feature
helps conserve your battery power.
You can turn the automatic redialling or
answering features on or off.
The following options are available:
Disable: the backlight is used according to the
setting in the Back Light menu option (M e n u
4.7.2); see page 89.
Enable: the backlight is used only during the
specified period of time. Set the required length
of time in hours and minutes, using the
appropriate number keys.
(Menu 4.8)
To turn a
feature...
Press the...
On
OK soft key.
A check mark is displayed in
front of the option.
Off
O K soft key again. The check
mark is no longer displayed.
Service Light
The following options are available:
This option allows you to select whether or not
the service light on the top of the phone is used
or in which colour it flashes.
Auto Redial: when this option is checked, the
phone makes up to ten attempts to redial a
phone number after an unsuccessful call.
Select the required colour from red, green, blue,
yellow, cyan, violet and light purple. When the
phone is ready for use, the service light will flash
in the appropriate colour.
Note: The interval between two call attempts
varies.
If you do not wish to use the service light, select
Off.
Active Flip: when this option is checked, you
can simply open the folder to answer a call.
When it is unchecked, you must open the folder
and press a key, depending on the setting of the
Anykey Answer option (see below).
Graphic Logo
This option allows you to display your operator s
logo instead of its name.
O n: the operator logo stored in your phone is
displayed in idle mode; if no logo has been
stored, the operator name is displayed.
Off: the operator name is displayed in idle
mode.
90
Anykey Answer: when this option is checked,
you can answer an incoming call by pressing any
key, except the
key and the Reject soft
key. To reject the call, press the
key or the
Reject soft key.
When this option is unchecked, you can only
press the
key or Accept soft key.
91
Phone Settings
Organiser
ShortCut
(Menu 4.9)
The navigation keys can be used as shortcut
keys. When held down in idle mode, they allow
you to access specific menu options directly.
To assign a shortcut to a key:
1. Select the key to be used as a shortcut key
by pressing the
or
key, followed by
the Select soft key.
¥
¥
¥
¥
Key up (
Key down (
Key right ( )
Key left ( )
The Organiser feature enables you to:
¥ View the calendar and organise your schedule
¥ Define a list of things to do
¥ Set the current date and time
¥ Set the alarm so that the phone rings at a
specific time (to remind you of an appointment
for example)
¥ Use the phone as a calculator for basic
mathematical equations or currency exchange
operations
Calendar
2. Select the menu option to be assigned to the
key by pressing the
or
key.
Note: To deactivate a shortcut key, select the
None option.
(Menu 5.1)
With the Calendar feature, you can:
¥ Consult the calendar
¥ W rite memos to keep track of your schedule
and trigger an alarm, if necessary
Consulting the Calendar
3. Press the Select soft key to save the
selection.
When you select the Calendar menu option
(Menu 5.1), the calendar is displayed. The
following options are available when you press
the Options soft key:
Reset Settings
Search all: displays all memos set, regardless
of the day and starting with the oldest. To scroll
through the memos, press the
or
key.
(Menu 4.10)
You can easily reset your phone to its default
configuration.
1. Select the Reset Settings menu option.
2. Enter the 8-digit phone password and press
the O K soft key.
Note: The password is preset to 00000000. To
change this password, refer to page 87.
92
Delete all: allows you to delete all memos. You
are asked to confirm your action.
Go to date: allows you to jump to a specific
date.
Exit: exits the Calendar feature and returns to
the idle mode.
93
Organiser
Organiser
To write or edit a memo on a specific date:
Once you have finished editing the memo, press
the O K soft key. The following options are then
available when you press the Options soft key.
1. Select the required date in the calendar, using
the navigation keys.
Alarm: allows you to set the alarm to ring on
the chosen day.
Writing a Memo
Note: To skip to the previous or next month,
press the
and
keys on the left side
of the phone.
2. Press the Select soft key.
Erase: allows you to delete the memo.
Copy to: allows you to copy the memo to
another date and/or time.
Move to: allows you to change the date and/or
time of the memo.
An empty memo screen is displayed to allow
you to enter your memo.
3. Enter your memo and then press the O K soft
key.
Note: For further details on how to enter
characters, refer to page 42.
You are asked if you wish to set an alarm.
4. If you want the alarm to ring on the chosen
day, press the Yes soft key.
To Do List
(Menu 5.2)
This feature allows you to:
¥ Draw up a list of tasks to be done
¥ Assign a priority and deadline to each task
¥ Sort the tasks by priority and status mark
Creating the To Do List
1. Press the N e w soft key.
Otherwise, press the N o soft key.
2. Enter the first task.
5. If you pressed the Yes soft key, set the time
for the alarm and press the O K soft key.
The colour of the date is changed to green to
indicate that a memo exists.
Note: You can enter up to 40 characters. For
further details on how to enter characters,
see page 42.
3. Press the O K soft key.
Editing a Memo
4. Select high, normal or low priority using the
or
key and press the Select soft key.
If you select a day for which a memo already
exists, you can press the Edit soft key to edit
the memo displayed.
5. Enter your deadline.
Note: For further details about how to enter
characters, refer to page 42.
If you do not want to set a deadline, press
the Skip soft key.
6. Press the O K soft key.
94
95
Organiser
Organiser
Editing the To Do List
To...
Then...
If tasks are already defined in the To Do List
when you select the To Do List menu option
(Menu 5.2), the current contents are displayed
with the status mark and priority (three stars for
high, two for normal and one for low).
Sort the existing
tasks by priority
or status
¥ Press the Options soft
key.
¥ Select the Sort option.
¥ Select the sort criterion
(High, L o w, D o n e or
U n d o).
Copy a task
¥ Highlight the task.
¥ Press the Options soft
key.
¥ Select the C o p y option.
¥ Change the text, priority
and deadline for the task
as required.
Copy a task to
the calendar
¥ Highlight the task.
¥ Press the Options soft
key.
¥ Select the C o p y to
calendar option.
¥ Change the text and
deadline for the task and
set the alarm as
required.
Delete a task
¥ Highlight the task.
¥ Press the Options soft
key.
¥ Select the Delete option.
Delete all tasks
¥ Press the Options soft
key.
¥ Select the Delete all
option.
¥ Confirm the deletion by
pressing the O K soft key.
Exit the To Do list
¥ Press the Options soft
key.
¥ Select the Exit option.
The following options are available:
To...
Then...
View the details
for a specific task
¥ Highlight the task.
¥ Press the V i e w soft key.
Change the
status of a
specific task
¥ Highlight the task.
¥ Press the key to mark
the task as completed as
of the current date and
time.
or
¥ Highlight the task.
¥ Press the Options soft
key.
¥ Select the M a r k option.
¥ Select the appropriate
status (D o n e or U n d o).
Create a new task
¥ Press the Options soft
key.
¥ Select the N e w option.
¥ Enter the text, priority
and deadline for the
task.
Edit an existing
task
96
¥ Highlight the task.
¥ Press the Options soft
key.
¥ Select the Edit option.
¥ Change the text, priority
and deadline for the
task.
97
Organiser
Time & Date
Organiser
(Menu 5.3)
This option allows you to change the current
time and date displayed. You can also check the
current time for Greenwich Mean Time (GMT)
and 21 major cities around the world.
Alarm
(Menu 5.4)
This feature allows you to:
¥ Set the alarm to ring at a specific time
¥ Set the phone to switch on automatically and
ring the alarm even if the phone is switched off
(Autopower menu option set to Enable)
The following options are available:
Set Time: allows you to enter the current time.
You can choose the time format via the T i m e
Format menu option (Menu 5.3.4).
Note: Before setting the time, you must specify
your time zone, via the World Time m e n u
option (Menu 5.3.3).
Set Date: allows you to enter the day, month
and year.
The following options are available:
Once Alarm: the alarm rings only once and is
then deactivated.
Daily Alarm: the alarm rings every day at the
same time.
Morning Call: the alarm rings to wake you up
in the morning.
To set the alarm:
World Time: allows you to check the current
time for Greenwich Mean Time (GMT) and 21
major cities around the world, using the
and
keys.
The screen shows the:
¥ City name
¥ Current date and time
¥ Time difference between the selected city and
your city if you have set the local time (see
below for further details) or GMT (by default)
1. Choose the type of alarm to be set.
2. Enter the required time and day of the week,
if applicable.
3. Press the O K soft key.
4. If you select Morning Call in Step 1, select
the repeat option; Monday to Friday or
Monday to Saturday.
Remove Alarm: deactivates all alarm settings.
To select the time zone in which you are located:
1. Select the city corresponding to your time
zone by pressing the
or key one or more
times. The local date and time are displayed.
2. Press the Set soft key.
Autopower: if this option is set to Enable, the
alarm will ring at the specified time, even when
the phone is switched off.
If the menu option is set to Disable and the
phone is switched off at the specified time, the
alarm will not ring.
Time Format: allows you to change the time
format to 24 Hours or 12 Hours.
98
99
Organiser
Organiser
To stop the alarm when it rings, open the phone
and press the Exit soft key.
When setting or viewing an alarm, the following
options are available when you press the
Options soft key:
Remove Alarm: deactivates the current alarm.
Alarm Sound Set: allows you to select the
alarm melody.
Calculator
Currency Exchange
(Menu 5.6)
Using this menu option, you can make currency
conversions.
1. Enter the current exchange rate of your
source currency and press the O K soft key.
You can insert a decimal point by pressing the
key.
2. Enter the amount for which you wish to
conduct the currency conversion and press
the O K soft key.
(Menu 5.5)
With this feature, you can use the phone as a
calculator. The calculator provides the basic
arithmetic functions; addition, subtraction,
multiplication and division.
The exchange rate amount you entered and
equivalent value are displayed.
3. Press the Exit soft key to exit the currency
convertor.
Using the Calculator
1. Enter the first number using the numeric
keys.
2. Press the right soft key until the required
arithmetic symbol appears: + (add), (subtract), x (multiply), / (divide).
3. Enter the second number.
4. Repeat Steps 1 to 3 as many times as
required.
Notes:
¥ To erase any mistakes and clear the display, press
the C key.
¥ To include a decimal point or a bracket, press the
left soft key until the required symbol is
displayed.
5. To calculate the result, press the
100
key.
101
Network Services
Network Services
To set your call diverting options:
These menu functions are network services.
Please contact your service provider to check
their availability and subscribe to them, if you
wish.
1. Select the type of call diverting required by
pressing the
or
key, and then press
the Select soft key.
Call Diverting
2. Select the type of calls to be diverted by
pressing the
or
key, and then press
the Select soft key.
(Menu 6.1)
This network service enables incoming calls to
be rerouted to the number that you specify.
Example: You may wish to divert your business
calls to a colleague while you are on
holiday.
Call diverting can be set up in the following
w ays:
Divert Always: all calls are diverted.
B u s y: calls are diverted if you are already
making another call.
No Reply: calls are diverted if you do not
answer the phone.
Unreachable: calls are diverted if you are not
in an area covered by your service provider.
The current status is displayed. If the option
has already been set, the number to which
the calls are diverted is displayed.
3. To...
Then...
Activate call
diverting
¥ Press the Activate
soft key.
¥ Go to Step 4.
Change the call
number
¥ Press the C h a n g e
soft key.
¥ Go to Step 4.
Deactivate call
diverting
Press the R e m o v e soft
key.
4. Enter the number to which the calls are to be
diverted and press the O K soft key.
Cancel All: all call diverting options are
cancelled.
To enter the international code, press the 0
key until the + sign is displayed.
You can specify individual diverting options for
each of the following call types:
¥ Voice calls only
¥ Data calls only
The phone sends your settings to the network
and the network s acknowledgement is
displayed.
Example: You can divert voice calls to your
colleague if you are already using the
phone.
102
You can deactivate all call diverting settings by
selecting the Cancel All option.
103
Network Services
Call Barring
Network Services
(Menu 6.2)
The call barring network service allows you to
restrict your calls.
3. Press the Activate soft key to confirm your
settings.
4. Enter your call barring password supplied by
your service provider.
Call barring can be set up in the following ways:
All Outgoing: calls cannot be made.
International: international calls cannot be
made.
International Except to Home: when abroad,
calls can be made only to numbers within the
current country and to your home country, that
is the country where your home network
provider is located.
The phone sends your settings to the network
and the network s acknowledgement is
displayed.
To deactivate specific call barring settings:
1. Select the call barring option to be
deactivated.
2. Select the type of call to which this option
applies.
All Incoming: calls cannot be received.
3. Press the Deactivate soft key.
Incoming While Abroad: calls cannot be
received when you are using your phone outside
your home service area.
Cancel All: all call barring settings are
deactivated; calls can be made and received
normally.
You can specify individual barring options for
each of the following call types:
¥ Voice calls only
¥ Data calls only
To set your call barring options:
1. Select the type of call barring required by
pressing the
or
key and then press
the Select soft key.
4. Enter your call barring password supplied by
your service provider.
The phone sends your settings to the network
and the network s acknowledgement is
displayed.
You can also deactivate all call barring settings
by selecting the Cancel All option.
Change Barring Password: you can set and
change the call barring password obtained from
your service provider using this option. You must
enter the current password before you can
specify a new one.
Once you have entered a new password, you are
asked to confirm it by entering it again.
2. Select the type of calls to be barred by
pressing the
or
key and then press
the Select soft key.
104
105
Network Services
Call Waiting
Network Services
(Menu 6.3)
This network service enables you to be informed
when someone is trying to reach you during
another call.
You can specify individual call waiting options for
each of the following call types:
¥ Voice calls only
¥ Data calls only
To set your call waiting options:
1. Select the type of calls to which the call
w aiting option is to be applied by pressing the
or
key and then press the Select
soft key.
The screen informs you whether call waiting
is activated or deactivated.
2. You can activate or deactivate the call waiting
feature as necessary by using the Activate or
Deactivate soft key respectively.
To return to the previous screen, press the
Exit soft key.
You can also deactivate all call waiting settings
by selecting the Cancel All option.
Network Selection
(Menu 6.4)
The Network Selection feature enables you to
indicate whether the network used when
roaming outside your home area is selected
automatically or manually.
Note: You can select a network other than your
home network only if it has a valid roaming
agreement with your home network.
To indicate whether the network is to be selected
automatically or manually when roaming:
1. W h e n Network Selection is displayed, press
the Select soft key.
2. Press the
or
key until the appropriate
option is highlighted and then press the O K
soft key.
If you select Automatic, you are connected
to the first available network when roaming.
If you select Manual, the phone scans for the
available networks. Go to Step 3.
3. Press the
or
key until the preferred
network is highlighted and then press the O K
soft key.
You are connected to that network.
106
107
Network Services
Caller ID
Network Services
(Menu 6.5)
You can prevent your phone number from being
displayed on the phone of the person being
called.
Note: Some networks do not allow the user to
change this setting.
The following options are available:
Default: the default setting provided by the
network is used.
Index List: lets you list, add or delete CUG
index numbers. The list of current CUG indexes
appears.
Add a new CUG index as advised by your service
provider or delete a selected group.
To...
Scroll the through
the existing CUG
indexes
Press the...
or key.
Add a new CUG
index
Options soft key,
select the A d d option
and enter the index.
Send Number: your number is sent each time
you make a call.
Delete a CUG
index
Options soft key and
select the Delete
option.
Closed User Group (CUG)
Activate a CUG
index
Options soft key and
select the Activate
option.
Hide Number: your number is not displayed on
the other person s phone.
(Menu 6.6)
This network service allows incoming and
outgoing calls to be restricted to a selected user
group. You may be a member of up to ten user
groups. For details on how to create, activate
and use a closed user group, contact your
service provider.
Example: A company lends SIM cards to its
employees and wants to restrict
outgoing calls to members of the same
team.
Activating a Closed User Group
If you select the Closed User Group menu, you
can enter the CUG function. You can now access
the following options after pressing the Select
soft key.
108
Outside Access: lets you enable or disable calls
to numbers other than those nominated for the
Closed User Group. This feature depends on the
nature of your CUG subscription. Please check
with your service provider.
Default Group: you may communicate a default
CUG to your service provider. If you have done
so, you can enable the Default Group option on
your phone. When making a call, you will be
given the option of using your default CUG,
instead of selecting one from the list.
Deactivate: deactivates the CUG function. This
menu appears only when the default group is
enabled or a CUG index is selected.
109
Network Services
Funbox
Band Selection
(Menu 6.7)
The F u n b o x menu contains several fun options.
For the phone to make and receive phone calls,
it must register with one of the available
networks. Your phone can handle any of the
following types of network:
¥ GSM 900
¥ GSM 1800
¥ Combined GSM 900/1800
¥ GSM 1900
The country where you purchased your phone
determines the default band that it uses. When
you travel abroad, you must remember to
change to an appropriate band. Proceed as
follows.
1. When Band Selection is displayed, press the
Select soft key.
2. Press the or key until the appropriate option,
G S M 9 0 0 / 1 8 0 0 or G S M 1 9 0 0, is highlighted
and press the O K soft key.
When you select a new band, your phone
displays a confirmation message and then
automatically searches for all the available
networks. Your phone then registers with a
preferred network within the selected band.
Games
(Menu 7.1)
You can enjoy three games with your phone.
Scroll to the required game, using the
and
keys and press the Select soft key. For
further details on the game, refer to the onscreen help.
WAP Browser
(Menu 7.2)
Your phone is equipped with a WAP Browser to
allow you to access and navigate the Wireless
W eb via your phone.
For further details on the W A P B r o w s e r menu,
refer to the WAP Browser User s Manual supplied
with your phone.
Downloads
(Menu 7.3)
You can download MIDlets (Java applications
running on mobile phones) from various sources
using the WAP Browser and store them in your
phone. You can then view the list of MIDlets
stored on the Games & More screen.
Note: Java services may be unavailable depending
upon the service provider.
Games & More
This menu option allows you to launch a MIDlet
and access various menu options.
For more details on how to download MIDlets via
the WAP Browser, refer to the WAP Browser
User s Manual supplied with your phone.
110
111
Funbox
Launching a MIDlet
1. From the Downloads screen, select the
Games & More option.
Funbox
: allows you to enter English characters using
the T9 mode. For details about this mode, see
page 44.
Note: To change case, press the 0 key.
2. Scroll to the desired MIDlet and press the
Launch soft key.
Using the Menus
From the Main Screen, press the M e n u soft key
to access the following options:
Info: displays information about the selected
MIDlet, such as the file size, application version,
vendor, and the location of the jad file, which is
the MIDlet description file.
R e m o v e: removes the selected MIDlet. When
the confirmation message appears, press the
R e m o v e soft key. To cancel your selection,
press the Cancel soft key.
Update: accesses the server and updates the
selected MIDlet.
Note: These menus are shown only when a
MIDlet has been downloaded.
Entering Text
When entering URL addresses, the following five
input modes are available:
A B C: allows you to enter upper-case English
characters.
abc: allows you to enter lower-case English
characters.
1 2 3: allows you to enter numbers.
S y m: allows you to enter symbols. After
highlighting the required symbol by pressing the
navigation keys, press the
key to insert it.
To change the text input mode, press the
key
until the appropriate indicator appears on the soft
key area of the display.
Sounds
In this menu, you can view the list of sounds
downloaded from the server. You can set the
downloaded sounds as the current ring tone, but
cannot send the sounds to other phones.
When the memory is full, a warning message is
displayed and the phone rejects additional sounds
until you erase obsolete ones.
Pictures
In this menu, you can view the list of pictures
downloaded from the server. You can set the
downloaded pictures as the current background
image, but cannot send them to other phones.
When the memory is full, a warning message is
displayed and the phone rejects additional pictures
until you erase obsolete ones.
Settings
The DNS (Domain Name Server) address of the
Java server is preset at the factory, but sometimes
you may need to change it. In this menu, you can
determine whether or not the address will be
automatically updated when needed.
Automatic: the server will automatically transmit
the address to the phone if it is changed.
Manual: you can manually change the address.
112
113
Solving Problems
Solving Problems
Before contacting the after-sales service,
perform the following simple checks. They may
save you the time and expense of an
unnecessary service call.
When you switch your phone on, the
following messages may appear
Insert SIM Card
¥ Check that the SIM card is correctly installed.
Phone Locked Enter Password
¥ The automatic locking function has been
enabled. You must enter the phone s password
before you can use the phone.
Enter PIN
No service,
Network failure
Not done is displayed
or
¥ The network connection was lost. You may be
in a weak signal area (in a tunnel or
surrounded by buildings). Move and try again.
¥ You are trying to access an option for which
you have not taken out a subscription with
your service provider. Contact the service
provider for further details.
You have entered a number but it was
not dialled
¥ Have you pressed the
key?
¥ Are you accessing the right cellular network?
¥ You may have set an outgoing call barring
option.
¥ You are using your phone for the first time.
You must enter the Personal Identification
Number supplied with the SIM card.
Your correspondent cannot reach you
¥ The PIN Check feature is enabled. Every time
the phone is swiched on, the PIN have to be
entered. To disable the feature, use the P I N
Check menu option (Menu 4.6.1).
¥ Are you accessing the right cellular network?
¥ Is your phone switched on (the
key
pressed for more than one second)?
¥ You may have set an incoming call barring
option.
Enter PUK
¥ The PIN code was entered wrongly three times
in succession and the phone is now blocked.
Enter the PUK supplied by your network
operator.
Your correspondent cannot hear you
speaking
¥ H ave you switched off the microphone?
¥ Are you holding the phone close enough to
your mouth? The microphone is located at the
bottom of the phone.
114
115
Solving Problems
Access Codes
The phone starts beeping and
**Warning** Low Battery flashes on
the display
¥ The battery is insufficiently charged. Replace
the battery and recharge it.
The audio quality of the call is poor
¥ Check the signal strength indicator on the
display (
); the number of bars indicates
the signal strength from strong (
) to weak
( ).
¥ Try moving the phone slightly or moving closer
to a window if you are in a building.
There are several access codes that are used by
your phone and its SIM card. These codes help
you protect the phone against unauthorised use.
When requested for any of the codes explained
below, key in the appropriate code (displayed as
asterisks) and press the O K soft key. If you
m a ke a mistake, press the C key one or more
times until the incorrect digit is cleared and then
continue entering the correct code.
The access codes, except for the PUK (PIN
Unblocking Key) and PUK2 codes can be
changed using Security menu options (M e n u
4.6). See page 79 for further details.
No number is dialled when you recall a
phonebook entry
Important! Avoid using access codes
resembling emergency numbers,
such as 112, so that you do not dial
an emergency number accidentally.
¥ Check that the number has been stored
correctly, by using the Phonebook Search
feature.
Phone Password
¥ Re-store the number, if necessary.
If the above guidelines do not enable you to
solve the problem, take a note of:
¥ The model and serial numbers of your phone
¥ Your warranty details
¥ A clear description of the problem
Then contact your local dealer or Samsung
after-sales service.
116
The Phone Lock feature uses the phone
password to protect your phone against
unauthorised use. The phone password is
supplied with the phone and is factory set to
00000000.
To...
Refer to...
Activate/deactivate the
Phone Lock feature
Page 80
(Menu 4.6.3).
Change the phone
password
Page 80
(Menu 4.6.4).
117
Access Codes
Access Codes
PIN
PIN2
The P ersonal Identification N umber or PIN (4 to
8 digits) protects your SIM card against
unauthorised use. It is usually supplied with the
SIM card.
The PIN2 (4 to 8 digits), supplied with some SIM
cards, is required to access specific functions,
such as setting the maximum cost of a call.
These functions are available if supported by
your SIM card.
If you enter an incorrect PIN three times in
succession, the code is disabled and cannot be
used until you re-enable it by entering the PUK
(see below).
To...
Refer to...
Activate/deactivate
the PIN Check feature
Page 79
(Menu 4.6.1).
Change the PIN
Page 80
(Menu 4.6.2).
PUK
The 8-digit PUK (P IN U nblocking K ey) is
required to change a disabled PIN. The PUK may
be supplied with the SIM card. If not, or you
have lost it, contact your service provider.
To re-enable your PIN:
1. Key in the PUK and press the O K soft key.
2. Enter a new PIN of your choice and press the
O K soft key.
3. When the Confirm New PIN message is
displayed, key in the same code again and
press the O K soft key.
If you enter an incorrect PUK ten times in
succession, the SIM card becomes invalid.
Contact your service provider for a new card.
118
If you enter an incorrect PIN2 three times in
succession, the code is disabled and you cannot
access the functions until you re-enable it by
entering the PUK2.
To change the PIN2, refer to page 81 (M e n u
4.6.7).
PUK2
The 8-digit PUK2 (PIN Unblocking Key 2),
supplied with some SIM cards, is required to
change a disabled PIN2. If you lose the code,
contact your service provider.
To re-enable your PIN2:
1. Key in the PUK2 and press the O K soft key.
2. Enter a new PIN2 of your choice and press
the O K soft key.
3. When the Confirm PIN2 message is
displayed, key in the same code again and
press the O K soft key.
If you enter an incorrect PUK2 ten times in
succession, you will not be able to access the
functions requiring the PIN2. Contact your
service provider for a new card.
119
Access Codes
Barring Password
The 4-digit barring password is required when
you use the Call Barring function. You obtain the
password from your service provider when you
subscribe to this function. See page 99 for
further details.
Health and Safety
Information
Information about Batteries
Type
Time
Standard Battery Extended Battery
(700 mA)
(900 mA)
Talk time
up to 2 hours
and 30 minutes
up to 3 hours
and 10 minutes
Standby time
up to 73 hours
up to 94 hours
(fully charged battery)
Information about Battery Usage
Standby time will be reduced in the following
conditions:
¥ When you use the additional features on your
phone, such as writing and storing messages,
playing games or connecting to the Internet.
¥ If you are frequently out of the service area.
¥ If you are out of the service area for a long
period of time.
¥ If you use the phone out of the network s local
service area.
¥ If you use the talk mode repeatedly.
¥ The battery can be charged and discharged
hundreds of times, but it will eventually wear
out. When the operation time for both talk
mode and standby mode is reduced by about
half, it is time to buy a new battery.
120
121
Health and Safety Information
Battery Precautions
Health and Safety Information
Precautions When Using Batteries
¥ Do not drop, knock or shake it. Rough handling
can break the battery or shorten its life.
Your phone is powered by a rechargeable Li-ion
standard battery.
¥ Do not store or carry flammable liquids, gases
or explosive materials in the same
compartment as the battery because it can
explode.
¥ Never use any charger or battery that is
damaged in any way.
¥ Use only Samsung-approved chargers. Using
other chargers can damage your battery or
overcharge it. Overcharging may shorten its
life.
¥ Do not short-circuit the battery. Accidental
short-circuiting can occur when a metallic
object, such as a coin, clip or pen, directly
connects the + and the - terminals of the
battery, which are metal strips on the back. Be
particularly careful when you carry a spare
battery in a pocket or bag. Short-circuiting the
terminals may damage the battery or the
object causing the short-circuit.
¥ Do not leave the battery in hot or cold places,
such as in a car in summer or in winter
conditions, as you will reduce the capacity and
life-time of the battery. Always try to keep the
battery at room temperature (0 ¡C ~ 40 ¡C). A
phone with a hot or cold battery may
temporarily not work, even when the battery is
fully charged.
¥ Keep it out of reach of small children. Do not
let children put the battery into their mouths.
¥ Do not use the battery if it is damaged,
because the battery fluid can be harmful. If
the battery fluid comes in contact with your
skin, flush with water and contact your doctor.
¥ Use the battery only for its intended purpose.
¥ If you use the phone near the network s base
station, it uses less power; talk and standby
time are greatly affected by the signal strength
on the cellular network and the parameters set
by the network operator.
¥ Battery charging time depends on the
remaining battery charge and the type of
battery and charger used. The battery can be
charged and discharged hundreds of times, but
it will gradually wear out. When the operation
time , including talk time and standby time is
noticeably shorter than normal, it is time to
buy a new battery.
¥ If left unused, a fully charged battery will
discharge itself over time.
¥ Use only Samsung-approved batteries and
recharge your battery only with Samsungapproved chargers. When a charger is not in
use, disconnect it from the power source. Do
not leave the battery connected to a charger
for more than a week, since overcharging may
shorten its life.
¥ Extreme temperatures will affect the charging
capacity of your battery: it may require cooling
or warming first.
¥ Use the battery only for its intended purpose.
122
123
Health and Safety Information
¥ Do not leave the battery in hot or cold places,
such as in a car in summer or winter
conditions, as you will reduce the capacity and
life-time of the battery. Always try to keep the
battery at room temperature. A phone with a
hot or cold battery may temporarily not work,
even when the battery is fully charged. Li-ion
batteries are particularly affected by
temperatures below 0 ¡C (32 ¡F).
¥ Do not short-circuit the battery. Accidental
short circuiting can occur when a metallic
object (coin, clip or pen) causes a direct
connection between the + and — terminals of
the battery (metal strips on the battery), for
example when you carry a spare battery in a
pocket or bag. Short-circuiting the terminals
m ay damage the battery or the object causing
the short-circuit.
¥ Dispose of used batteries in accordance with
local regulations. Always recycle. Do not
dispose of batteries in a fire.
Health and Safety Information
Road Safety
Your wireless phone gives you the powerful
ability to communicate by voice, almost
anywhere, anytime. But an important
responsibility accompanies the benefits of
wireless phones, one that every user must
uphold.
When driving a car, driving is your first
responsibility. When using your wireless phone
behind the wheel of a car, practice good common
sense and remember the following tips.
1. Get to know your wireless phone and its
features, such as speed dial and redial. If
available, these features help you to place
your call without taking your attention off the
road.
2. When available, use a hands-free device. If
possible, add an extra layer of convenience
and safety to your wireless phone with one of
the many hands-free accessories available
today.
3. Position your wireless phone within easy
reach. Be able to access your wireless phone
without removing your eyes from the road. If
you get an incoming call at an inconvenient
time, let your voice mail answer it for you.
4. Let the person you are speaking with know
you are driving; if necessary, suspend the call
in heavy traffic or hazardous weather
conditions. Rain, sleet, snow, ice and even
heavy traffic can be hazardous.
5. Do not take notes or look up phone numbers
while driving. Jotting down a To Do list or
flipping through your phonebook takes your
attention aw ay from your primary
responsibility, driving safely.
124
125
Health and Safety Information
Health and Safety Information
6. Dial sensibly and assess the traffic; if
possible, place calls when you are not moving
or before pulling into traffic. Try to plan calls
when your car will be stationary. If you need
to make a call while moving, dial only a few
numbers, check the road and your mirrors,
then continue.
Operating Environment
7. Do not engage in stressful or emotional
conversations that may be distracting. Make
the people with whom you are talking aw are
that you are driving and suspend
conversations that have the potential to divert
your attention from the road.
When connecting the phone or any accessory to
another device, read its user s guide for detailed
safety instructions. Do not connect incompatible
products.
8. Use your wireless phone to call for help. Dial
the emergency number in the case of fire,
traffic accident or medical emergencies.
Remember, it is a free call on your wireless
phone!
9. Use your wireless phone to help others in
emergencies. If you see a car accident, crime
in progress or other serious emergency where
lives are in danger, call the emergency
number, as you would want others to do for
you.
10. Call roadside assistance or a special nonemergency wireless assistance number when
necessary. If you see a broken-down vehicle
posing no serious hazard, a broken traffic
signal, a minor traffic accident where no one
appears injured, or a vehicle you know to be
stolen, call roadside assistance or any other
special non-emergency wireless number.
126
Remember to follow any special regulations in
force in any area and always switch off your
phone whenever it is forbidden to use it, or
when it may cause interference or danger.
As with other mobile radio transmitting
equipment, users are advised that for the
satisfactory operation of the equipment and for
the safety of personnel, it is recommended that
the equipment should only be used in the normal
operating position (held to your ear with the
antenna pointing over your shoulder).
Electronic Devices
Most modern electronic equipment is shielded
from radio frequency (RF) signals. However,
certain electronic equipment may not be
shielded against the RF signals from your
wireless phone. Consult the manufacturer to
discuss alternatives.
Pacemakers
Pacemaker manufacturers recommend that a
minimum distance of 15 cm (6 inches) be
maintained between a wireless phone and a
pacemaker to avoid potential interference with
the pacemaker. These recommendations are
consistent with the independent research and
recommen-dations of Wireless Technology
Research.
127
Health and Safety Information
Health and Safety Information
Persons with pacemakers:
Vehicles
¥ Should always keep the phone more than 15
cm (6 inches) from their pacemaker when the
phone is switched on
RF signals may affect improperly installed or
inadequately shielded electronic systems in
motor vehicles. Check with the manufacturer or
its representative regarding your vehicle.
¥ Should not carry the phone in a breast pocket
¥ Should use the ear opposite the pacemaker to
minimise potential interference
You should also consult the manufacturer of any
equipment that has been added to your vehicle.
If you have any reason to suspect that
interference is taking place, switch off your
phone immediately.
Posted Facilities
Switch off your phone in any facility where
posted notices require you to do so.
Hearing Aids
Some digital wireless phones may interfere with
some hearing aids. In the event of such interference, you may wish to consult your hearing
aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical devices,
consult the manufacturer of your device to
determine if it is adequately shielded from
external RF energy. Your physician may be able
to assist you in obtaining this information.
Switch off your phone in health care facilities
when any regulations posted in these areas
instruct you to do so. Hospitals or health care
facilities may be using equipment that could be
sensitive to external RF energy.
128
Potentially Explosive Atmospheres
Switch off your phone when in any area with a
potentially explosive atmosphere and obey all
signs and instructions. Sparks in such areas
could cause an explosion or fire resulting in
bodily injury or even death.
Users are advised to switch off the phone while
at a refuelling point (service station). Users are
reminded of the need to observe restrictions on
the use of radio equipment in fuel depots (fuel
storage and distribution areas), chemical plants
or where blasting operations are in progress.
Areas with a potentially explosive atmosphere
are often but not always clearly marked. They
include below deck on boats, chemical transfer
or storage facilities, vehicles using liquefied
petroleum gas (such as propane or butane),
areas where the air contains chemicals or
particles, such as grain, dust or metal powders,
and any other area where you would normally be
advised to turn off your vehicle engine.
129
Health and Safety Information
Emergency Calls
This phone, like any wireless phone, operates
using radio signals, wireless and landline
networks as well as user-programmed functions,
which cannot guarantee connection in all
conditions. Therefore, you should never rely
solely on any wireless phone for essential
communications (medical emergencies, for
example).
Remember, to make or receive any calls the
phone must be switched on and in a service area
with adequate signal strength. Emergency calls
m ay not be possible on all wireless phone
networks or when certain network services
and/or phone features are in use. Check with
local service providers.
To make an emergency call:
1. If the phone is not on, switch it on.
2. Key in the emergency number for your
present location (for example, 112 or any
other official emergency number). Emergency
numbers vary by location.
3. Press the key.
If certain features are in use (call barring, for
example), you may first need to deactivate those
features before you can make an emergency
call. Consult this document and your local
cellular service provider.
When making an emergency call, remember to
give all the necessary information as accurately
as possible. Remember that your phone may be
the only means of communication at the scene
of an accident; do not cut off the call until given
permission to do so.
130
Health and Safety Information
Other Important Safety
Information
¥ Only qualified personnel should service the
phone or install the phone in a vehicle. Faulty
installation or service may be dangerous and
m ay invalidate any warranty applicable to the
device.
¥ Check regularly that all wireless phone
equipment in your vehicle is mounted and
operating properly.
¥ Do not store or carry flammable liquids, gases
or explosive materials in the same
compartment as the phone, its parts or
accessories.
¥ For vehicles equipped with an air bag,
remember that an air bag inflates with great
force. Do not place objects, including both
installed or portable wireless equipment in the
area over the air bag or in the air bag
deployment area. If wireless equipment is
improperly installed and the air bag inflates,
serious injury could result.
¥ Switch off your phone before boarding an
aircraft. The use of wireless phones in aircraft
m ay be dangerous to the operation of the
aircraft, and is illegal.
¥ Failure to observe these instructions may lead
to the suspension or denial of telephone
services to the offender, or legal action, or
both.
131
Health and Safety Information
Care and Maintenance
Your phone is a product of superior design and
craftsmanship and should be treated with care.
The suggestions below will help you fulfill any
w arranty obligations and allow you to enjoy this
product for many years.
¥ Keep the phone and all its parts and
accessories out of the reach of small children s.
¥ Keep the phone dry. Precipitation, humidity
and liquids contain minerals that will corrode
electronic circuits.
Health and Safety Information
¥ Do not paint the phone. Paint can clog the
device s moving parts and prevent proper
operation.
¥ Use only the supplied or an approved
replacement antenna. Unauthorised antennas
or modified accessories may damage the
phone and violate regulations governing radio
devices.
¥ If the phone, battery, charger or any accessory
is not working properly, take it to your nearest
qualified service facility. The personnel there
will assist you, and if necessary, arrange for
service.
¥ Do not touch the phone with wet hands while
it is charging. Doing so may give you an
electric shock or damage the phone.
¥ Do not use or store the phone in dusty, dirty
areas, as its moving parts may be damaged.
¥ Do not store the phone in hot areas. High
temperatures can shorten the life of electronic
devices, damage batteries, and warp or melt
certain plastics.
¥ Do not store the phone in cold areas. When
the phone warms up to its normal operating
temperature, moisture can form inside the
phone, which may damage the phone s
electronic circuit boards.
¥ Do not drop, knock or shake the phone. Rough
handling can break internal circuit boards.
¥ Do not use harsh chemicals, cleaning solvents
or strong detergents to clean the phone. Wipe
it with a soft cloth slightly dampened in a mild
soap-and-w ater solution.
132
133
Glossary
Glossary
To help you understand the main technical terms
and abbreviations used in this booklet and take
full advantage of the features on your mobile
phone, here are a few definitions.
Active Flip
Ability to answer a call simply by opening the
phone.
Call Barring
Ability to restrict outgoing and incoming calls.
Call Diverting
Ability to reroute calls to another number.
Call Holding
Ability to put one call on standby while
answering or making another call; you can then
switch between the two calls, as required.
Call Waiting
Ability to inform users that they have an
incoming call when engaged on another call.
Caller Line Identification Services (Caller
ID)
Services allowing subscribers to view or block
the telephone numbers of callers.
GPRS (General Packet Radio Service)
New non-voice value-added service that allows
information to be sent and received across a
mobile telephone network. GPRS guaranties
continuous connection to the Internet for mobile
phone and computer users. It is based on the
Global System for Mobile Communication (GSM)
circuit-switched cellular phone connections and
the Short Message Service (SMS).
134
GSM (Global System for Mobile
Communication)
International standard for cellular
communication, guaranteeing compatibility
between the various network operators. GSM
covers most European countries and many other
parts of the world.
Java
Programming language generating applications
that can run on all hardware platforms, whether
small, medium or large, without modification. It
has been promoted for and geared heavily to the
W eb, both for public Web sites and Intranets.
When a Java program runs from a Web page, it
is called a Java applet. When it is run on a
mobile phone or pager, it is called a MIDlet.
Multiparty Calling
Ability to establish a conference call involving up
to five additional parties.
Phone Password
Security code used to unlock the phone when
you have selected the option to lock it
automatically each time it switches on.
PIN (Personal Identification Number)
Security code that protects the phone against
unauthorised use. The PIN is supplied by the
service provider with the SIM card. It may be a
four to eight-digit number and can be changed,
as required.
PUK (PIN Unblocking Key)
Security code used to unlock the phone when an
incorrect PIN has been entered three times in
succession. The eight-digit number is supplied by
the service provider with the SIM card.
135
Glossary
Roaming
Use of your phone when you are outside your
home area (when travelling for example).
SDN (Service Dialling Numbers)
Telephone numbers supplied by your network
provider and giving access to special services,
such as voice mail, directory inquiries, customer
support and emergency services.
SIM (Subscriber Identification Module)
Card containing a chip with all the information
required to operate the phone (network and
memory information, as well as the subscriber s
personal data). The SIM card fits into a small
slot on the back of the phone and is protected
by the battery.
Glossary
Tri Band
Ability to handle any of the following types of
network: GSM 900, GSM 1800, combined GSM
900/ 1800 and GSM 1900 MHz bands, for
greater call success and wider roaming.
Your phone automatically searches for the last
network used. If, for any reason, this network is
unavailable, your phone will attempt to register
with a different network.
Voice Mail
Computerised answering service that
automatically answers your calls when you are
not available, plays a greeting (optionally in your
own voice) and records a message.
SMS (Short Message Service)
Network service sending and receiving messages
to and from another subscriber without having to
speak to the correspondent. The message
created or received can be displayed, received,
edited or sent.
Soft Keys
Two keys marked and on the phone, the
purpose of which:
¥ Varies according to the function that you are
currently using
¥ Is indicated on the bottom line of the display
just above the corresponding key
136
137
➀ Press the M e n u soft
key.
➁ Scroll with the
or
keys through the
list of the menus until
you reach the required
menu.
➂ Press the Select soft
key.
➃ Scroll with the
or
keys through the
list of the options until
the required one is
selected.
➄ Press the Select soft
key.
¥ Each of the two soft keys (
and
perform the function indicated by the
text above it (bottom line on the
display.)
Access the
Menu
Function
Press and hold the
key.
➀ Enter the number.
➁ Press the
key.
Briefly press the
key.
➀ Open the phone and
press the V i e w soft
key.
➁ Scroll with the
or
keys through
the missed calls.
➂ To return the call,
press the
key.
Switch On/Off
M a kes a Call
End a Call
View Missed
Calls Immediately
After Missing
Them
Quick Reference Card
Tri Band SGH-S108 GPRS Telephone
Choose
the Alert
Type
Adjust the
Volume
Answer a
Call
➀ Select the Alert Type
menu option (3.3)
➁ Select an option:
¥ Light only
¥ Melody
¥ Vibration
¥ Vibra+Melody
➂ Press the Select soft
key
Press the
or
key
on the left side of the
phone.
Open the phone
or
press the
key.
Search for a
Number
in the
Phonebook
Store
Numbers
in the
Phonebook
➀ Press the N a m e soft key.
➁ Select the Search soft key.
➂ Enter the first letters of
the name.
➃ To scroll through the
names, press the
or
keys.
➄ Press the V i e w soft key.
➅ To scroll through the
numbers, press the
or
keys.
➆ Press the
key to dial.
➀ Enter the number.
➁ Press the Save soft key.
➂ Select an icon for label.
➃ Press the Select soft key.
➄ Enter the name.
➅ Press the O K soft key.
➆ If necessary, change the
location.
➇ Press the O K soft key.
➈ Press the
key to
return to idle mode.
* Some of the contents in this manual may differ from your phone,
depending on the software installed or your service provider.
SGH-S108
WAP Browser
User’s Manual
ELECTRONICS
World Wide Web
http://www.samsungmobile.com
Printed in Korea
Code No.: GH68-00000A
English. 07/2002. Rev. 1.0
Contents
What is WAP?
WAP (Wireless Application Protocol) is the
gateway to a new world of mobile data. It
provides a universal standard, enabling you
to access Web-based interactive information
services and applications directly from your
mobile phone.
About the WAP Browser............................
Setting Up the WAP Browser.....................
Accessing the WAP Browser ......................
Configuring the WAP Browser ....................
Getting Started ......................................... 10
Starting the WAP Browser......................... 10
Exiting the WAP Browser .......................... 10
Using the WAP Browser ............................ 11
Using the Soft Keys.................................. 11
Navigating the WAP Browser ..................... 11
Entering Text, Numbers or Symbols ........... 12
Using the WAP Browser Menus ................. 13
Using and Selecting Menu Options ............. 13
Reload ................................................... 13
Home..................................................... 13
Go to URL............................................... 14
Show URL............................................... 14
Edit Home .............................................. 15
About the
WAP Browser
Your phone comes equipped with a WAP (Wireless
Application Protocol) Browser, making it possible for
you to access the Wireless Web.
Setting Up the
WAP Browser
Before using the WAP Browser, you must set the
parameters for the proxy server used by your
service provider.
The WAP Browser allows you to:
• Access up-to-the-minute information via your
phone
• View specially designed text versions of popular
Internet sites including Yahoo!®, CNN MobileSM
and the Weather Channel®
Browsing the Wireless Web using your phone is
unlike using your computer, in that site providers
have:
• Selected only the critical aspects of their site for
wireless phone users
• Removed most graphics
Each time you start the WAP Browser, the phone
connects to the Wireless Web and the service
indicator icon (
or
) appears on the display
to inform you that you are:
• Are connected to the Wireless Web
• Will be billed accordingly (rates vary according to
your service option)
The WAP Browser ends the network connection
after a certain period of inactivity and automatically
reconnects as necessary. For this reason, you may
find that you are billed for several network
connections within a single session. This is normal
and is designed to minimise your bill.
Accessing the WAP Browser
To access the WAP Browser menu, proceed as
follows.
1. When the idle screen is displayed, press the
Menu soft key to enter the menu facility.
Service Provider
07:30
Wed 06 Mar
Menu
Name
2. Press the
or
key one or more times until
the Funbox menu option is displayed, and then
press the Select soft key. You can also press
the
key directly.
Organiser
Network
Services
Funbox
Select
Setting Up the WAP Browser
Setting Up the WAP Browser
3. Press the
or
key one or more times to
highlight WAP Browser, then press the Select
soft key. You can also press the
key directly.
Three submenus are available.
Select Goto URL to access the site
quickly, Edit to edit the selected
address and Erase to delete the
selected address.
Funbox
Games
Settings
Allows you to set up five proxy
servers for the WAP Browser.
Clear
Cache
Clears the information stored in
the cache (the phone’s temporary
memory used to store the most
recently accessed Web pages).
WAP Browser
Downloads
Select
4. Press the
or
key one or more times to
highlight the required option and then press the
Select soft key.
Configuring the WAP Browser
To configure the WAP Browser, proceed as follows.
WAP Browser
Home
Favorite
Settings
Clear Cache
Select
Option
Description
Home
Connects the phone to the network
and loads the homepage of the
Wireless Web service provider.
Favorite
Allows you to store the URL
addresses of your favourite Web
sites. You can access this menu
directly by pressing and holding
down the
key while using the
WAP Browser. To store a URL
address, select an empty location
and enter the address.
1. In the WAP Browser menu, highlight Settings
using the
and
keys, then press the
Select soft key. You can also press the
key
directly.
2. Select a proxy server and enter the parameters
required. Contact your service provider for
details.
Parameter
Description
Profile
Name
Name that you wish to assign to
the HTTP proxy server.
Homepage Address of your startup
URL
homepage. When the default
homepage is displayed, you can
delete it using the
key and
enter your own choice.
Setting Up the WAP Browser
Parameter
Description
Security
Data transmission mode. Choose
Secure to protect your data
against unauthorised access;
otherwise, choose Non-Secure.
IP Address WAP gateway address required to
connect to the Internet.
Bearer
Bearer to be used for each type of
network address accessed: GPRS
or Data.
Setting Up the WAP Browser
Note: The WAP Browser settings may vary,
depending on the service provider. Contact
your service provider for further information.
3. After selecting each of these settings, a dialog
box is displayed; you can either enter the
information required or choose between given
options. When you are satisfied with your input,
press the OK soft key.
4. When you have finished configuring the WAP
Browser, press the
key or the right soft
key.
The remaining options depend on the Bearer
setting, as indicated below.
When the bearer is set to Data
Parameter Description
Login
Name
PPP server login ID.
Password
PPP server password.
Dial-up
Number
PPP server phone number.
Data Call
Type
Data call type: Analogue or
ISDN.
When the bearer is set to GPRS
Parameter Description
User Name User ID required to connect to the
GPRS network.
Password
Password required to connect to
the GPRS network.
APN
Access point name used for the
address of the GPRS network
gateway.
Getting
Started
Using the
WAP Browser
Starting the WAP Browser
Using the Soft Keys
To start the WAP Browser when the idle screen is
displayed, press the
key or press the Menu soft
key, followed by the
and
keys.
A bar containing browser commands is located at
the bottom of the WAP Browser display. The soft
keys
below the bar are used to execute these
commands. The two keys are called soft keys
because their function changes depending on the
WAP Browser application in use.
A connection is established with your service
provider and the corresponding homepage is
displayed.
The content of the WAP Browser startup homepage
depends on your Wireless Web service provider. To
scroll through the screen, use the
and
keys.
Note: To access the startup homepage from any
other screen in the WAP Browser, use the
Home option. For more information on the
WAP Browser menus, refer to page 13.
Navigating the WAP Browser
To...
Then...
Scroll through and
select browser
items
Press the
or
key until
the
symbol points to the
required item, and then press
the OK soft key to confirm the
selection.
Exiting the WAP Browser
To exit the browser at any time, simply press
the
key or press and hold down the
key.
10
Select a numbered Press the corresponding
item
numeric key.
Return to the
previous page
Press the Back soft key or
the
key.
Return to the
startup homepage
Select the Home menu
option; for more information
on this option, refer to
page 13.
11
Using the WAP Browser
Using the WAP
Browser Menus
Entering Text, Numbers or Symbols
Using and Selecting Menu Options
When you are prompted to enter text, the current
text entry mode is indicated on the screen. The
following modes are available.
Various menu options are available when you are
using the WAP Browser to navigate the Wireless
Web.
Mode
Description
To access a menu option, proceed as follows.
Allows you to enter letters in the
alphabet. Press the corresponding key
until the required letter is displayed.
1. Press and hold down the
A menu is displayed.
Allows you to enter numbers.
Note: To enter symbols, press the
key repeatedly
until the required symbol is displayed.
key.
2. Highlight the required menu option by pressing
the
and
keys.
3. Select the option by pressing the Select soft
key.
4. If necessary, select the secondary option using
the
and
keys, and press the Select soft
key to confirm.
To...
Then...
Change
modes
Press the
times.
Enter a space
Press the
Edit text
• Set the cursor to the right of the
character(s) to be corrected.
• Press the
key as required.
• Enter the correct character(s).
key one or more
key.
Note: The menus may vary, depending on your
version of the WAP Browser.
Reload
This option reloads the current page.
Home
This option takes you back at any time to the
homepage of the Wireless Web service provider.
12
13
Using the WAP Browser Menus
Using the WAP Browser Menus
Go to URL
Edit Home
This option allows you to enter manually the URL
address of the required Web page.
With this feature, you can change the startup
homepage manually.
After entering an address, press the OK soft key to
go there directly.
To change the homepage, enter the required URL
and press the OK soft key.
Show URL
For more information on entering text, numbers or
symbols, refer to page 12.
This feature displays the URL address of the site to
which you are currently connected. It also enables
you to declare the current site as the startup
homepage.
To...
Then...
Declare the current
page as your startup
homepage
Press the Option soft key,
select the Save to Home
option and press Select.
Set a bookmark for
the current page
Press the Option soft key,
select the Save to
Bookmark option and
press Select.
Cancel your setting
Press the Back soft key.
14
15
* Some of the contents in this manual may differ from
your phone, depending on the software installed or
your service provider.
ELECTRONICS
Printed in Korea
World Wide Web
http://www.samsungmobile.com
Code No.: GH68-00000A
English. 07/2002. Rev. 1.0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2002:07:19 09:19:47Z
Modify Date                     : 2002:08:12 12:11:24-03:00
Page Count                      : 81
Creation Date                   : 2002:07:19 09:19:47Z
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
Mod Date                        : 2002:08:12 12:11:24-03:00
Metadata Date                   : 2002:08:12 12:11:24-03:00

EXIF Metadata provided by EXIF.tools