Samsung Electronics Co WSM520V Audio transceiver module User Manual Users manual
Samsung Electronics Co Ltd Audio transceiver module Users manual
Users manual
WSM520V
Version 1.0 Samsung Electronics page 1 of 8
User Manual
1. Introduction
The WSM520V module is wireless audio module based on AV5100. The AV5100 is 5GHz wireless audio
SoC (System-on-chip), optimized for building point to multi-point digital wireless audio solutions such as
wireless subwoofers, wireless rear speakers and in home theater system. The AV5100 contains all the
necessary radio transceiver and digital baseband circuitry to form a complete digital wireless node without the
need for external processing.
The WSM520V can be powered from a +5V supply input and the AV5100 contains all the necessary power
management and analog circuitry needed to operate the chip.
The WSM520V can operate in upper bands (5725~5825MHz) of 5GHz spectrum, enabling worldwide
coverage.
2. Feature
Product form factor
‐ Module Size (mm): 40.0 (W) X 26.0 (L) X 3.0 (H)
‐ PCB size (mm): 40.0 (W) X 2.6.0 (L) x 1.0 (H)
‐ Shield can (mm): 24.7 (W) X 21.9 (L) X 2.0(H)
‐ Antenna Type : PCB Printed Antenna
WSM520V
Version 1.0 Samsung Electronics page 2 of 8
Complete VMX wireless audio comm. system
5.725-5.825 GHz RF operation
96dB SNR
Multiple OTA audio configuration
Low, fixed latency (<20ms)
Separate RF transmit and receive RF I/O
RX diversity
USB digital audio capability
I2S digital audio capability
Complete power management
24pin I/O connector
3. Block Diagram
The Block diagram of WSM520V module is shown in the below picture.
WSM520V block diagram
PCB Antenna 0: 5725~5825MHz
PCB Antenna 1: 5725~5825MHz
X-TAL: 16MHz
WSM520V
Version 1.0 Samsung Electronics page 3 of 8
4. Functional Diagram
The functional diagrams of WSM520V module are shown in the below pictures
The WSM520V can provide wireless audio service in applications with wireless subwoofer solution and
wireless 2.1 solutions.
WSM520V
Version 1.0 Samsung Electronics page 4 of 8
5. Operating Conditions
Symbol Parameter Min. Typ. Max. Unit
V dc Supply Voltage 4.5 5.0 5.5 V
I dc Supply current - - 500 mA
Temp Operating Temperature 5 35 ℃
6. RF Characteristics
Parameter Value Unit
Modulation Pi/4DQPSK / SSB
RF Frequency Range 5725 – 5825 MHz
Bandwidth 2 MHz
RF Frequency
Channel (0) LO : 5725, Fc: NOT USED
Channel (1) LO : 5727, Fc: NOT USED
Channel (2) LO : 5729, Fc: 5730.35
Channel (3) LO : 5731, Fc: 5732.35
Channel (4) LO : 5733, Fc: 5734.35
.
.
.
.
.
.
Channel (45) LO : 5815, Fc: 5816.35
Channel (46) LO : 5817, Fc: 5818.35
Channel (47) LO : 5819, Fc: 5820.35
Channel (48) LO : 5821, Fc: NOT USED
Channel (49) LO : 5823, Fc: NOT USED
MHz
Diversity 1TX / 2RX
Antenna peak gain 2.2 dBi
RF TX output power (tolerance) 14.0 (+2dB) dBm
7. Transmit mode
In transmit mode, the audio engine transforms the audio data into packetized digital IQ signals. These
are in turn pulse-shaped before conversion by DAC to match to the analog IQ inputs of the radio
transceiver. The radio transceiver has programmable baseband filter to lower the RF spectrum side lobes
and to suppress the DAC image and the DAC spurious. The output power is programmable. A power
detector (PD_Out) on the radio transceiver enables close-loop TX power control. The differential RF TX
DA outputs are connected via a balun filter to Power amplifier and the amplified TX carrier signal is
radiated by a printed antenna in the module after going through Transmit/Receive switch placed between
WSM520V
Version 1.0 Samsung Electronics page 5 of 8
power amplifier and the printed antenna.
8. Receive mode
In receive mode , antenna diversity is supported. The single ended output of the T/R switch is connected to
the differential RF LNA inputs in the AV5100 through balun filter. Filtering and amplification is all
performed by the radio transceiver function in the AV5100. The gain setting is controlled by BB. The
analog IQ outputs are sampled by the BB having dual channel ADC to convert. The received data is
demodulated and fed to the audio processing engine controlling the audio function
9. Clock
The main crystal is connected to the AV5100 IC. The clock frequency is 16MHz and feed it to the AV5100.
10. I/O interface
The WSM520V module has 24pin-FPC connector for I/O interface. The 24-pin connector is configured as
the following table.
Pin Number Pin Name I/O Description
1 VDD_5V PWR Regulated 4.5V to 5.5V input
2 VDD_5V PWR Regulated 4.5V to 5.5V input
3 GPIO5 / I2CS_SCL I/O I2C serial clock slave
4 GPIO4 / I2CS_SDA I/O I2C serial data slave
5 GPIO19 / WCLK1 I/O I2S Left Light clock 1
6 RESET I Reset
7 GPIO9 / MISO_EXT_FLASH I/O External flash memory data output
8 GPIO8 / MOSI_EXT_FLASH I/O External flash memory data input
9 GPIO17 / I2CM_SCL I/O I2C serial clock master
10 GPIO16 / I2CM_SDA I/O I2C serial data master
11 GPIO10 /MCLK I/O 12.288MHz Audio clock I/O
12 GND GND GND
13 GPIO11 /I2S_BCK0 I/O I2S Bit clock 0
14 GPIO12 /I2S_WCLK0 I/O I2S Left Light clock 0
15 GPIO6 / CS_EXT_FLASH I/O External flash memory chip select
16 GPIO13 /I2S_DAT_0 I/O I2S data 0
17 GPIO7 / SCLK_EXT_FLASH I/O External flash memory clock input
18 GPIO14 / I2S_DAT_1 I/O I2S data 1
19 GPIO15 / I2S_DAT_2 I/O I2S data 2
20 GPIO18 /BCK1 I/O I2S Bit clock 1
21 GPIO2 /S_SSB I/O
22 GPIO3 /S_SCLK I/O
23 GPIO24 I/O GPIO
24 GND GND GND
WSM520V
Version 1.0 Samsung Electronics page 6 of 8
11. Notice
FCC Statement
This device complies with Part 15 of FCC Rules, Operation is Subject to following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that cause undesired operation.
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void user s authority to operate the equipment.
This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a different circuit from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjuction with any other antenna or transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement;
This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or
transmitter.
A minimum separation distance of 20
㎝
must be maintained between the antenna and the person for this appliance
to satisfy the RF exposure requirements.
USER MANUAL OF THE END PRODUCT:
In the users manual of the end of product, the end user has to be informed to keep at least 20cm separation with the
antenna while this end product is installed and operated.
WSM520V
Version 1.0 Samsung Electronics page 7 of 8
IC Statement
The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can
be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
If the size of the end product is smaller than 8x10cm, then additional FCC part15.19statement is required to be available
in the users manual; This device complies with Part15 of FCC rules.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: A3LWSM520V ". If
the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available
on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(3) this device may not cause harmful interference and
(4) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
This device and its antenna(s) must not be co-located or operation in conjuction with any other antenna or transmitter.
The device could automatically discontinue transmission in case of absence of information to transmit, or operational
failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive
codes where required by the technology.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
WSM520V
Version 1.0 Samsung Electronics page 8 of 8
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement
of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is
integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/
uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this
equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the
antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency
exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this
equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with
Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC : 649E‐WSM520V ".