Samsung 591Sg Users Manual File

SyncMaster 794V 10246002

591SG 10254139

2015-01-23

: Samsung Samsung-591Sg-Users-Manual-276657 samsung-591sg-users-manual-276657 samsung pdf

Open the PDF directly: View PDF .
Page Count: 82

SyncMaster 591S/591SG/591V/594MG/592V/794V/793DF/793MG/793SG/793V/794MG/793S/783DF/788DF Plus

Install driver Install programs

SyncMaster 591S/591SG/591V/594MG/592V/

794V/793DF/793MG/793SG/793V/

794MG/793S/783DF/788DF Plus

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to

the equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Ground to prevent an electric shock

Power

When not used for extended periods of time, set your computer to a screen

saver.

zIf the same image is present for long periods of time, Phosphor Burnt can be

occured, or the screen may be blurred.

zThe images here are for reference only, and are not applicable in all cases (or

countries).

Do not use a damaged or loose plug.

zThis may cause electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

zThis may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

zAn improper ground may cause electric shock or equipment damage.

(Class l Equipment only.)

Insert the power plug firmly so that it does not come loose.

zA bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon

them, which could cause damage.

zThis may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

zThis may cause fire.

Do not disconnect the power cord while using the monitor.

surge may be caused by the separation and may damage the monitor.

Do not use the power cord when the connector or plug is dusty.

zIf the connector or plug of the power cord is dusty, clean it with a dry

cloth.

zUsing the power cord with a dusty plug or connector may cause an

electric shock or fire.

To disconnect the apparatus from the mains, the plug must be pulled out

from the mains socket, therefore the mains plug shall be readily

operable.

zThis may cause an electric shock or fire.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a

location with heavy dust, high or low temperatures, high humidity, and exposed

to chemical substances and where it operates for 24 hours such as at airports,

train stations etc.

Failure to do so may cause serious damage to your set.

Put your monitor in a location with low humidity and a minimum of dust.

zFailure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

zThis may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or shelf so that the end of the

base does not protrude from the showcase or shelf.

zDropping the product may cause damage to the product or the person

carrying it.

Do not place the product on an unstable or small surface area.

zPlace the product on an even end stable surface ,as the product may fall

and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

zTake care, as someone, specifically children may trip over it.

TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN

FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

zOtherwise, this may cause fire.

Keep any heating devices away from the power cable.

zA melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a

bookshelf, closet, etc.

zAny increase in internal temperature may cause fire.

Set down the monitor carefully.

zThe monitor could be damaged or broken.

Do not place the monitor face down.

zThe CDT surface may be damaged.

Do not use the monitor without the monitor stand.

zIt could break down or cause fire due to bad ventilation.

zIf the monitor must be used without the supplied stand, take steps to

insure proper ventilation.

When installing the product, make sure to keep it away from the wall

(more than 10 cm/4 inches) for ventilation purposes.

zPoor ventilation may cause an increase in the internal temperature of

the product, resulting in a shortened component life and degraded

performance.

Keep the plastic packaging (bag) out of children’s reach.

zThe plastic packaging (bag) may cause suffocation if children play with

it.

Clean

When cleaning the monitor case or the surface of the CDT, wipe with a slightly

moistened, soft fabric.

Do not clean Flat monitor with water. Use a water-diluted mild detergent.

(Some detergents contain significant amounts of alcohol-based solvents, which

can damage (color change) or crack the monitor case. The antiglare/anti-static

surface coating on the CDT may also be affected.)

Dilute the detergent (1:10 ratio) with water before using.

Do not spray water or detergent directly onto the monitor.

zThis may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

zYou may prevent the coated CDT from being damaged or the monitor

cabinet from being dissolved, cracked or discolored.

zYou may buy a recommended detergent at any Service Center.

If the connector between the plug and the pin is dusty or dirty, clean it

properly using a dry cloth.

zA dirty connector may cause electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

zOtherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using

a soft, dry cloth.

zDo not use any chemicals such as wax, benzene, alcohol, thinners,

insecticide, air freshener, lubricant or detergent.

Contact a Service Center or Customer Center for interior cleaning once a

year.

zKeep the product's interior clean. Dust which has accumulated in the

interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover(or back).

zThis may cause electric shock or fire.

zRefer to a qualified servicing company.

If your monitor does not operate normally - in particular, if there are any

unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or the Service Center.

zThis may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture;

do not install inside a vehicle.

zThis may cause malfunction, an electric shock or fire.

zEspecially avoid operating the monitor near water or outdoors where the

monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off

and unplug the power cord. Then contact a Service Center.

zThe monitor may cause a malfunction, electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is

not used for a long period of time.

zFailure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal

cable.

zThis may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the

signal cable.

zThis may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

zBad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects

on the monitor.

zThis may cause malfunction, an electric shock or fire.

zIf a foreign substance enters the monitor, unplug the power cord and

contact the Service Center .

Do not place any heavy objects on the monitor.

zThis may cause electric shock or fire.

Keep the product away from combustible chemical sprays or

inflammable substances.

zThis may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

zThis may cause electric shock, fire or injury.

Keep the monitor away from any magnetic substances.

zThis may cause discoloring or distortion of the image.

Viewing the monitor continuously at a too close angle may result in

damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of

using the monitor.

Do not install the product on an unstable, uneven surface or a location

prone to vibrations.

zDropping the product may cause damage to the product or the person

carrying it. Using the product in a location prone to vibrations may

shorten the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord.

Make sure that all cables, including the antenna cable and cables

connected to other devices, are disconnected before moving the

monitor.

zFailure to disconnect a cable may damage it and lead to fire or an

electric shock.

Place the product out of children’s reach, as they could damage by

hanging onto it.

zA falling product may cause injury to the person or even fatality.

When not using the product for an extended time period, keep the

product unplugged

zOtherwise, this may cause heat emission from the accumulated dirt or

degraded insulation, causing electric shock or fire.

Do not place children's favorite objects (or anything else that may be

tempting) on the product.

zChildren may try to climb on the product to retrieve an object. The

product could fall, causing physical damage or even death.

Good Postures When Usin

the Monito

Try to maintain a good posture when using the monitor.

zKeep your back straight.

zKeep a distance of about 45 ~ 50 cm between your eyes

and the monitor screen. Look at the screen from slightly

above it, and have the monitor directly in front of you.

zTilt the monitor upwards by 10 ~20 degrees. Adjust the

monitor height so that the top of the monitor is slightly

below eye level.

zAdjust the monitor angle so that there is no reflected light

on the screen.Try to maintain your arms perpendicular to

your armpits.

zKeep your arms level with the back of your hands.

zKeep the angle of the elbow perpendicular.

zKeep the angle of the knees at more than 90 degree. Do

not let your feet fall up from the floor. Adjust the arm

position so that it is below the heart.

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to bu

tional items.

Unpacking

Monitor and Stand

(Some models include a stand attached.)

Manual

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

icTune™ software

Cable

SyncMaster 591S/591SG/591V/594MG/793DF/793MG

793SG/793V/794MG/793S/783DF

Power Cord

Stand

For Multimedia model (Option)

Manual

User Guide

Cable

Sound Cables

(

2each

)

DC Power Cord

Stand

Multimedia S

eaker Stand

Front

Menu button [MENU]

Opens the OSD menu. Also used to exit the OSD menu or

return to the previous menu.

Adjust buttons [ ] These buttons allow you to highlight and adjust items in the

menu.

Enter button [ ] Used to select the OSD menu.

Power button [ ] Use this button for turn the monitor on and off.

Power indicator This light glows green during normal operation, and blinks green

once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving

functions. For energy conservation, turn your monitor OFF when it is not needed, or when

leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

Power port Connect the power cord for your monitor to the power port on

the back of the monitor.

Signal Cable Connect the signal cable to the video port on your computer

(video board, video card, or graphics card).

See Connecting the Monitor for further information regarding cable connections.

Bottom

Tilt/Swivel Base You can separate the base from the monitor.

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to bu

tional items.

Unpacking

Monitor and Stand

(Some models include a stand attached.)

Manual

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

icTune™ software

Cable

SyncMaster 592V/794V/788DF Plus

Power Cord

Stand

For Multimedia model (Option)

Manual

User Guide

Cable

Sound Cables

(

2each

)

DC Power Cord

Stand

Multimedia S

eaker Stand

Front

Menu button [MENU]

Opens the OSD menu. Also used to exit the OSD menu or

return to the previous menu.

Adjust buttons [ ] These buttons allow you to highlight and adjust items in the

menu.

Enter button [ ] Used to select the OSD menu.

Power button [ ] Use this button for turn the monitor on and off.

Power indicator This light glows green during normal operation, and blinks green

once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving

functions. For energy conservation, turn your monitor OFF when it is not needed, or when

leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

Power port Connect the power cord for your monitor to the power port on

the back of the monitor.

Signal Cable Connect the signal cable to the video port on your computer

(video board, video card, or graphics card).

See Connecting the Monitor for further information regarding cable connections.

Bottom

Tilt/Swivel Base You can separate the base from the monitor.

Connecting the Monitor

Setup-For Multimedia model | Multimedia Speaker Stand

1. Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

2. Use a connection appropriate for your computer.

2-1. Connecting to a computer

Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.

2-2. Connecting to a new Macintosh

Connect the monitor to the Macintosh computer using the D-SUB connection cable.

Turn on your computer and monitor. If your monitor displays an image, installation is

complete.

Setu

-For Multimedia model

1. Turn off your computer and unplug the power cord.

2. Connect the end of the signal cable to your computer's video port(video board, video card or

graphics card).

3. Connect one end of the other sound cable to the Mic Input jack on your sound card or

computer.Connect the other end of this cable to the Mic By-pass jack on the back of the

monitor stand.

4. Plug the DC power cord from the stand into a nearby outlet.

5. Connect the power cord for your monitor to the power port on the back of the monitor.

6. Plug the power cord for the monitor and the power cord for your computer into a nearby

outlet.

7. Turn on your computer and monitor.

8. Turn up or down the On-Off control terminal on the stand of the monitor until it clicks.

9. Execute a sound program, music or sound effect in your computer and then adjust the volume

by turning up or down until the sound volume is appropriate.

10. Adjust the treble and bass.

Sound distortion may occur when the monitor is placed on top of a mostly hollow cabinet

such as your computer. If this occurs, place a pad or magazine beneath the monitor stand.

High sound volume may also cause sound distortion; lower the volume.

Multimedia S

eaker Stand

1. Mic By-pass Jack

To transmit your voice,connect a sound cable from

the Mic By-pass jack to the mic in jack on the sound

card slot in your computer.

2. Stereo Input Jack

Connect a sound cable from the input source(sound

card,computer,CD-ROM drive).

3. DC Power Cord

Connect DC power cord to monitor DC 12V output

jack.

4. Power Indicator

Glows green when the speakers are turned on.

5. On/Off Volume

Turns On/Off and adjusts the output volume.

6. Treble Control

Use to control high frequencies.

7. Bass Control

Use to control low frequencies.

8. Mic Input Jack

To transmit your voice,connect a microphone to this

jack.

9. Headphone Jack

To listen in privacy,connect headphones here.

10.

Detachable Stand Top

Base Installation

Tilt/Swivel Base | Attaching and Removing the Base

Tilt/Swivel Base

With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable

viewin

le.

The base is detachable.

Attachin

and Removin

the Base

our monitor was su

lied with the base detached, attach the base as follows.

Remove the twist-tie before attaching the base to the monitor.

Attachin

the Base

1. Place the monitor upside-down on a flat work surface.

2. Align the tabs on the base with the corresponding slots on the bottom of the monitor.

3. Press the base onto the monitor until the tabs are fully engaged in the slots.

4. Push the base toward the front of the monitor until the release latch clicks into the locked

position.

* Do not bend the snap.

Removin

the Base

5. Squeeze and pull up on the release latch on the base.

6. Push the base toward the back of the monitor and lift up to remove the base.

The base will align with the monitor slots in only one position.

Installing the Monitor Driver(Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM

included with this monitor. Driver installation is slightly different from one operating

system to another. Follow the directions appropriate for the operating system you

have.

Prepare a blank disk and download the driver program file at the Internet web site shown

here.

zInternet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)

http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

1. Insert the CD into the CD-ROM drive.

2. Click "Windows"

3. Choose your monitor model in the model list, then click the "OK".

4. If you can see following message window, then click the "Continue Anyway" button.

Then click "OK". (Microsoft® Windows® XP/2000 Operating System)

5. Monitor driver installation is completed.

This monitor driver is under certified MS logo and this installation doesn't

damage your system. The certified driver will be posted on Samsung

Monitor homepage.

http://www.samsung.com/.

Installing the Monitor Driver(Manual)

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

When prompted by the operating system for the monitor driver, insert the CD-ROM

included with this monitor. Driver installation is slightly different from one operating

system to another. Follow the directions appropriate for the operating system you

have.

Prepare a blank disk and download the driver program file at the Internet web site shown

here.

zInternet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)

http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" icon.

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".

4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.

6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".

7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the

model list and click the "Next" button.

8. If you can see following message window, then click the "Continue Anyway" button. Then

click "OK" button.

9. Click the "Close" button, then click "OK" button continually.

This monitor driver is under certified MS logo and this installation doesn't

damage your system. The certified driver will be posted on Samsung

Monitor homepage.

http://www.samsung.com/.

10. Monitor driver installation is completed.

Microsoft® Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "Insert disk" window.

2. Click the "Browse" button on the "File Needed" window.

3. Choose A:(D:\Driver) then click the "Open" button and then click "O

" button.

How to install

1. Click "Start" , "Setting" , "Control Panel".

2. Double click the "Display" Icon.

3. Choose the "Settings" tab and then click "Advanced..".

4. Choose "Monitor".

5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.

6. Choose "Display a list of the known drivers for this device so that I can choose a

specific driver" then click "Next" and then click "Have disk".

7. Click the "Browse" button then choose A:(D:\Driver).

8. Click the "Open" button, then click "OK" button.

9. Choose your monitor model and click the "Next" button then click "Next" button.

10. Click the "Finish" button then the "Close" button.

If you can see the "Digital Signature Not Found" window then click the "Yes"button.

And click the "Finish" button then the "Close" button.

Case1: If the "Properties" button is inactive, it means your monitor is properly configured.

Please stop installation

Case2: If the "Properties" button is active, click the "Properties" button then follow next steps

continually.

Microsoft® Windows® Millennium Operating System

1. Click "Start" , "Setting" , "Control Panel".

2. Double click "Display" icon.

3. Select the "Settings" tab and click "Advanced Properties" button.

4. Select the "Monitor" tab.

5. Click the "Change" button in the "Monitor Type" area.

6. Choose "Specify the location of the driver".

7. Choose "Display a list of all the driver in a specific location.." then click "Next" button.

8. Click the "Have Disk" button

9. Specify A:\(D:\driver) then click "OK" button.

10. Select "Show all devices" and choose the monitor that corresponds to the one you

connected to your computer and click "OK".

11. Continue choosing "Close" button and "OK" button until you close the Display Properties

dialogue box.

Microsoft® Windows® NT Operating System

1. Click Start, Settings, Control Panel, and then double-click Display icon.

2. In Display Registration Information window, click Settings Tab and then click All Display

Modes.

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)

and then click OK.

4. Click Apply button if you see the screen working normally after clicking Test. If the screen is

not normal, change to a different mode (lower mode of resolution, colors or frequency).

If there is no Mode at All Display Modes, select the level of resolution and vertical

frequency by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. The third screen is for setting your mouse.

3. Set a mouse for your computer.

4. The next screen is for selecting a keyboard.

5. Set a Keyboard for your computer.

6. The next screen is for setting your monitor.

7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency

directly.)

8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)

9. Enter the model name of your monitor. This information will not affect the actual execution

of X-Window.

10. You have finished setting up your monitor.

Execute X-Window after setting other requested hardware.

Natural Color

Natural Color Software Pro

ram

One of the recent problems in using a computer is that the color of the images printed out by a

printer or other images scanned by a scanner or a digital camera are not the same as those

shown on the monitor.

The Natural Color S/W is the very solution for this problem. It is a color administration system

developed by Samsung Electronics in association with Korea Electronics &

Telecommunications Research Institute (ETRI).

This is only available for Samsung monitors and ensures that the color of the images on the

monitor are the same as the printed or scanned images.

For more information, refer to Help (F1) in the software program.

Installing the Natural Color Software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural

Color screen will appear. Click on Natural Color in the startup window to install the Natural

Color software.

To install the program manually, insert the CD included with the Samsung monitor into the CD-

ROM Drive, click the Windows [Start] button, select select [Execute].

Enter D:\color\NCProSetup.exe and then press the <Enter> key.

(If the drive where the CD is inserted is not D:\, enter the applicable drive.)

Uninstalling the Natural Color Software Program

Select [Settings]/[Control Panel] from the [Start] menu and then double-click [Add/Delete a

program].

Select Natural Color from the list and then click the

[

Add/Delete

]

button.

User Control Buttons

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Use to select the OSD menu.

Direct-Access Features

Brightness

SyncMaster 591S/591V/591SG/594MG

Menu Description

When OSD is not on the screen, push the button to adjust brightness.

Contrast

Menu Description

When OSD is not on the screen, push the button to adjust Contrast.

OSD Functions

Select an icon that you want to know from the OSD menu to display a text or animation

explanation of that icon.

Menu Description Play/Stop

You can use the on-screen menus to change the brightness

according to personal preference.

You can use the on-screen menus to change the contrast

according to personal preference.

A "Moiré" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the horizontal moire adjustments.

A "Moirë" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the vertical moire adjustments.

The Degauss feature will remove color impurities caused by

magnetic fields.

Use the recall feature to reset these monitor settings to their

original levels: Position, Size, Pincushion, Trapezoid,

Parallelogram, Pinbalance, Rotation, H-Moire,and V-Moire.

Note: If you have selected "Yes", all settings listed above will

be reset. All other settings will remain the same.

Menu Description Play/Stop

Color temperature is a measure of the 'warmth' of the image

colors. (6500K / 9300K)

Use to adjust the monitor color setting.(Red)

Use to adjust the monitor color setting.(Green)

Use to adjust the monitor color setting.(Blue)

Standard Red Green Blue (sRGB) is a defined default color

space. If a monitor, printer and scanner are all calibrated to

the sRGB color characteristics, then you can find color

matching from each peripheral.

Note:When the monitor is in the sRGB mode, Brightness /

Contrast adjustment is not available.

Menu Description Play/Stop

Follow these instructions to change the horizontal position of

the monitor's entire display.

Follow these instructions to change the vetical position of the

monitor's entire display.

Follow these instructions to change the horizontal size of the

monitor's entire display.

Follow these instructions to change the vertical size of the

monitor's entire display.

Adjust the pincushion setting when the sides of the display

are bowed in or bowed out.

Adjust the pinbalance setting when the sides of the display

are bowed towards the left or right.

Adjust the trapezoid setting when the top or bottom of the

display is too large or small.

Adjust the parallelogram setting when the display is leaning

left or right.

Provides information about the display timing and sync signals polarity(user mode).

These screens do not allow any changes to the settings, they are for information only.

User Control Buttons

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Use to select the OSD menu.

Direct-Access Features

Brightness

SyncMaster 592V

Menu Description

When OSD is not on the screen, push the button to adjust brightness.

Contrast

Menu Description

When OSD is not on the screen, push the button to adjust Contrast.

OSD Functions

Select an icon that you want to know from the OSD menu to display a text or animation

explanation of that icon.

Menu Description Play/Stop

You can use the on-screen menus to change the brightness

according to personal preference.

You can use the on-screen menus to change the contrast

according to personal preference.

A "Moiré" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the horizontal moire adjustments.

A "Moirë" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the vertical moire adjustments.

The Degauss feature will remove color impurities caused by

magnetic fields.

Use the recall feature to reset these monitor settings to their

original levels: Position, Size, Pincushion, Trapezoid,

Parallelogram, Pinbalance, Rotation, H-Moire,and V-Moire.

Note: If you have selected "Yes", all settings listed above will

be reset. All other settings will remain the same.

Menu Description Play/Stop

Color temperature is a measure of the 'warmth' of the image

colors. (6500K / 9300K)

Use to adjust the monitor color setting.(Red)

Use to adjust the monitor color setting.(Green)

Use to adjust the monitor color setting.(Blue)

Standard Red Green Blue (sRGB) is a defined default color

space. If a monitor, printer and scanner are all calibrated to

the sRGB color characteristics, then you can find color

matching from each peripheral.

Note:When the monitor is in the sRGB mode, Brightness /

Contrast adjustment is not available.

Menu Description Play/Stop

Follow these instructions to change the horizontal position of

the monitor's entire display.

Follow these instructions to change the vetical position of the

monitor's entire display.

Follow these instructions to change the horizontal size of the

monitor's entire display.

Follow these instructions to change the vertical size of the

monitor's entire display.

Adjust the pincushion setting when the sides of the display

are bowed in or bowed out.

Adjust the pinbalance setting when the sides of the display

are bowed towards the left or right.

Adjust the trapezoid setting when the top or bottom of the

display is too large or small.

Adjust the parallelogram setting when the display is leaning

left or right.

Provides information about the display timing and sync signals polarity(user mode).

These screens do not allow any changes to the settings, they are for information only.

User Control Buttons

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Use to select the OSD menu.

Direct-Access Features

Brightness

SyncMaster 793S/793V/793SG/794MG/

783DF/793DF/793MG

Menu Description

When OSD is not on the screen, push the button to adjust brightness.

Contrast

Menu Description

When OSD is not on the screen, push the button to adjust Contrast.

OSD Functions

Select an icon that you want to know from the OSD menu to display a text or animation

explanation of that icon.

Menu Description Play/Stop

You can use the on-screen menus to change the brightness

according to personal preference.

You can use the on-screen menus to change the contrast

according to personal preference.

A "Moiré" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the horizontal moire adjustments.

A "Moirë" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the vertical moire adjustments.

The Degauss feature will remove color impurities caused by

magnetic fields.

Use the recall feature to reset these monitor settings to their

original levels: Position, Size, Pincushion, Trapezoid,

Parallelogram, Pinbalance, Rotation, H-Moire,and V-Moire.

Note: If you have selected "Yes", all settings listed above will

be reset. All other settings will remain the same.

Menu Description Play/Stop

Color temperature is a measure of the 'warmth' of the image

colors. (6500K / 9300K)

Use to adjust the monitor color setting.(Red)

Use to adjust the monitor color setting.(Green)

Use to adjust the monitor color setting.(Blue)

Standard Red Green Blue (sRGB) is a defined default color

space. If a monitor, printer and scanner are all calibrated to

the sRGB color characteristics, then you can find color

matching from each peripheral.

Note:When the monitor is in the sRGB mode, Brightness /

Contrast adjustment is not available.

Menu Description Play/Stop

Follow these instructions to change the horizontal position of

the monitor's entire display.

Follow these instructions to change the vetical position of the

monitor's entire display.

Follow these instructions to change the horizontal size of the

monitor's entire display.

Follow these instructions to change the vertical size of the

monitor's entire display.

Adjust the pincushion setting when the sides of the display

are bowed in or bowed out.

Adjust the pinbalance setting when the sides of the display

are bowed towards the left or right.

Adjust the trapezoid setting when the top or bottom of the

display is too large or small.

Adjust the parallelogram setting when the display is leaning

left or right.

Adjust the rotation setting when the entire display is tilted left

or right.

Provides information about the display timing and sync signals polarity(user mode).

These screens do not allow any changes to the settings, they are for information only.

User Control Buttons

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Use to select the OSD menu.

Direct-Access Features

Brightness

SyncMaster 794V/788DF Plus

Menu Description

When OSD is not on the screen, push the button to adjust brightness.

Contrast

Menu Description

When OSD is not on the screen, push the button to adjust Contrast.

OSD Functions

Select an icon that you want to know from the OSD menu to display a text or animation

explanation of that icon.

Menu Description Play/Stop

You can use the on-screen menus to change the brightness

according to personal preference.

You can use the on-screen menus to change the contrast

according to personal preference.

A "Moiré" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the horizontal moire adjustments.

A "Moirë" pattern can appear on your screen, looking like a

series of concentric circles or arcs. To eliminate this pattern,

use the vertical moire adjustments.

The Degauss feature will remove color impurities caused by

magnetic fields.

Use the recall feature to reset these monitor settings to their

original levels: Position, Size, Pincushion, Trapezoid,

Parallelogram, Pinbalance, Rotation, H-Moire,and V-Moire.

Note: If you have selected "Yes", all settings listed above will

be reset. All other settings will remain the same.

Menu Description Play/Stop

Color temperature is a measure of the 'warmth' of the image

colors. (6500K / 9300K)

Use to adjust the monitor color setting.(Red)

Use to adjust the monitor color setting.(Green)

Use to adjust the monitor color setting.(Blue)

Standard Red Green Blue (sRGB) is a defined default color

space. If a monitor, printer and scanner are all calibrated to

the sRGB color characteristics, then you can find color

matching from each peripheral.

Note:When the monitor is in the sRGB mode, Brightness /

Contrast adjustment is not available.

Menu Description Play/Stop

Follow these instructions to change the horizontal position of

the monitor's entire display.

Follow these instructions to change the vetical position of the

monitor's entire display.

Follow these instructions to change the horizontal size of the

monitor's entire display.

Follow these instructions to change the vertical size of the

monitor's entire display.

Adjust the pincushion setting when the sides of the display

are bowed in or bowed out.

Adjust the pinbalance setting when the sides of the display

are bowed towards the left or right.

Adjust the trapezoid setting when the top or bottom of the

display is too large or small.

Adjust the parallelogram setting when the display is leaning

left or right.

Adjust the rotation setting when the entire display is tilted left

or right.

Provides information about the display timing and sync signals polarity(user mode).

These screens do not allow any changes to the settings, they are for information only.

Installation

1. Insert the installation CD into the CD-ROM drive.

2. Click the MagicTune™ installation file.

3. Select installation Language, Click "Next".

4. When the Installation Shield Wizard window appears, click "Next."

5. Select "I agree to the terms of the license agreement" to accept the terms of use.

6. Choose a folder to install the MagicTune™ program.

7. Click "Install."

8. The "Installation Status" window appears.

9. Click "Finish."

10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.

Double-click the icon to start the program.

Installation Problems

The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network

environment.

System Requirements

zWindows 2000

zWindows XP Home Edition

zWindows XP Professional

zWindows Vista™

Hardware

z32 MB Memory above

z60 MB Hard disk space above

* For more information, visit the MagicTune™ website.

MagicTune™ execution icon may not appear depending on specification of computer

system or monitor. If that happens, press F5 Key.

It is recommended using MagicTune™ in Windows® 2000 or

later.

Uninstall

The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the

Windows® Control Panel.

Perform the following steps remove MagicTune™ .

1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on

Windows® XP, go to [Control Panel] in the [Start] menu.

2. Click the "Add or Remove Programs" icon in Control Panel.

3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™ ." Click on it to highlight

it.

4. Click the "Change/Remove" button to remove the program.

5. Click "Yes" to begin the uninstall process.

6. Wait until the "Uninstall Complete" dialog box appears.

Visit the MagicTune™ website for technical support for MagicTune™ , FAQs (questions and answers) and

software upgrades.

Check List

Before calling for service, check the information in this section to see if you can remedy any

problems yourself. If you do need assistance, please call the phone number on the

Information section or contact your dealer.

Symptom Check List Solutions

No images on the

screen. I cannot turn on

the monitor.

Is the power cord

connected properly?

Check the power cord connection and

supply.

Can you see ""

the screen?

Check the signal cable connection.

If the power is on, reboot

the computer to see the

initial screen(the login

screen), which can be

seen.

If the initial screen (the login screen)

appears, boot the computer in the applicable

mode (the safe mode for Windows

ME/XP/2000) and then change the

frequency of the video card.

(Refer to the Preset Timing Modes)

Note: If the initial screen (the login screen)

does not appear, contact a service center or

your dealer.

Can you see ""

the screen?

You can see this message when the signal

from the video card exceeds the maximum

resolution and frequency that the monitor

can properly handle.

Adjust the maximum resolution and

frequency that the monitor can handle

properly.

There is no image on the

screen.

Is the power indicator on

the monitor blinking at 1

second intervals?

The monitor is in PowerSaver mode.

Press any key on the keyboard to activate

the monitor and restore the image on the

screen.

The image on the screen

is shaking.

Check the monitor

configuration to see if it

is in Interlace Mode.

(Interlace Mode: Vertical

frequency 43 Hz, 87 Hz

(i), etc)

Change the vertical frequency to Non-

Interlace mode by referring to the video card

manual.

Are there any magnetic

products such as a

power adapter, speaker

or a high voltage wire

near by?

Move the monitor away from anything that

can create a strong magnetic field.

Is the voltage stable? The screen image can appear to shake or

vibrate at a particular time of day due to low

supply voltage.

The screen image can also appear to shake or vibrate if there is a

problem with the video card or the computer's main board.

The screen shows

strange colors or just

black and white.

Is the screen displaying

only one color as if

looking at the screen

through a cellophane

paper?

Check the signal cable connection.

Make sure the video card is fully inserted in

it's slot.

Have the screen colors

become strange after

running a program or

due to a crash between

applications?

Reboot the computer.

Has the video card been

set properly?

Set the video card by referring to the video

card manual.

The screen suddenly has

become unbalanced.

Have you changed the

video card or the driver?

Adjust screen image position and size using

the OSD.

Have you adjusted the

resolution or frequency

on the monitor?

Adjust the resolution and frequency of the

video card.

(Refer to the Preset Timing Modes).

The screen can be unbalanced due to the cycle of the video card

signals. Readjust Position by referring to the OSD.

The screen is out of

focus or OSD cannot be

adjusted.

Have you adjusted the

resolution or frequency

on the monitor?

Adjust the resolution and frequency of the

video card.

(Refer to the Preset Timing Modes).

The screen is partially

distorted.

Are there any magnetic

products such as an

adapter, speaker or a

high voltage wire near

the monitor?

Enter the OSD and perform a "Degauss".

Keep the monitor away from any magnetic

products.

LED is blinking but no

images on the screen.

Is the frequency properly

adjusted when checking

the Display Timing on

the menu?

Adjust the frequency properly by referring to

the video card manual and the Preset Timing

Modes.

(The maximum frequency per resolution may

differ from product to product.)

There are only 16 colors

shown on the screen.

The screen colors have

changed after changing

the video card.

Have the Windows

colors been set properly?

Windows ME/2000/XP:

Set the colors properly at the Control Panel

→ Display → Settings.

Has the video card been

set properly?

Set the video card by referring to the video

card manual.

There is a message that

reads "Unrecognized

monitor, Plug & Play

(VESA DDC) monitor

found".

Have you installed the

monitor driver?

Install the monitor driver according to the

Driver Installation Instructions.

See the video card

manual to see if the Plug

& Play (VESA DDC)

function can be

supported.

Install the monitor driver according to the

Driver Installation Instructions.

Check when

MagicTune™ does not

function properly.

MagicTune™ feature is

found only on PC (VGA)

with Window OS that

supports Plug and Play.

* To check whether your PC is available for

MagicTune™ feature, follow the

steps below (When Windows is XP);

Control Panel → Performance and

Maintenance → System → Hardware →

Device Manager → Monitors → After

deleting Plug and Play monitor, find 'Plug

and Play monitor' by searching new

Hardware.

MagicTune™ is an additional software for

the monitor. Some graphic cards may not

support your monitor. When you have a

problem with the graphic card, visit our

website to check the compatible graphic

card list provided.

http://www.samsung.com/monitor/magictune

MagicTune™ doesn't

work properly.

Have you changed your

PC or video graphic

card?

Download the latest program. The program

can be downloaded

http://www.samsung.com/monitor/magictune.

Did you install the

program?

Reboot the computer after installing the

program for the first time. If a copy of the

program is already installed, remove it,

reboot the computer, and then install the

program again. You need to reboot the

computer for it to operate normally after

installing or removing the program.

Visit the MagicTune™ website and download the installation software for MagicTune™

MAC.

Check the following items if there is trouble with the monitor.

1. Check if the power cord and the video cables are properly connected to the computer.

2. Check if the computer beeps more than 3 times when booting.

(If it does, request an after-service for the main board of the computer.)

3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video)

driver and the monitor driver.

4. Check if the scanning ratio of the video screen is set at 50Hz ~ 160Hz .

(Do not exceed 65Hz when using the maximum resolution.)

5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,

remove the Display Adapter at the "Control Panel→System→Device Administrator" and then

reboot the computer to reinstall the adapter (video) driver.

If problems repeatedly occur, contact an authorized service center.

Q & A

Question Answer

How can I change the

frequency?

Frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version

of the driver used. (Refer to the computer or the video card

manual for details.)

How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control

Panel→Display→Settings.

* Contact the video card manufacturer for details.

How can I set the Power Saving

function?

Windows ME/XP/2000 : Set the function at BIOS-SETUP of the

computer or the screen saver. (Refer to Windows/Computer

Manual).

The monitor makes a sound

when it is turned on.

This is normal as some sound may be generated when the metal

case and the electromagnet, which are installed to block any

electromagnetic waves, interact with each other.

How can I clean the outer

case/Picture tube?

Disconnect the power cord and then clean the monitor with a soft

cloth, using either a cleaning solution or plain water.

Do not leave any remains of the detergent nor scratch the case.

Do not allow any water to go inside the monitor.

Self-Test Feature Check

Self-Test Feature Check | Warning Messages | Environment | Useful Tips

Your monitor provides a self test feature that allows you to check whether your monitor is

functioning properly.

Self-Test Feature Check

1. Turn off both your computer and the monitor.

2. Unplug the video cable from the back of the computer.

3. Turn on the monitor.

If the monitor is functioning properly, you will see a box in the illustration below.

This box appears during normal operation if the video cable becomes disconnected or

damaged.

4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the

monitor.

If your monitor screen remains blank after using the previous procedure, check your video

controller and computer system; your monitor is functioning properly.

Warning Messages

If there is something wrong with the input signal, the message below appears on the screen

or the screen goes blank although the power indicator LED is still on. The message may

indicate that the monitor is out of scan range or that you need to check the signal cable.

Environment

The location and the position of the monitor may influence the quality and other

features of the monitor.

1. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer

to another room.

2. Remove all electronic devices such as radios, fans, clocks and telephones that are

within 3 feet (one meter) of the monitor.

3. Degauss the monitor if any devices were removed from the area.

Useful Tips

zA monitor recreates visual signals received from the computer. Therefore, if there is trouble with

the computer or the video card, this can cause the monitor to become blank, have poor coloring,

noise, unavailable video mode, etc. In this case, first check the source of the problem, and then

contact a service center or your dealer.

zJudging the monitor's working condition

If there is no image on the screen or a ""

message comes up, disconnect the cable from the

computer while the monitor is still powered on.

{If there is a message coming up on the screen or if the screen goes white, this means the

monitor is in working condition.

{In this case, check the computer for trouble.

General

Model Name SyncMaster 591S/591V/591SG/594MG

Picture Tube

Type 15" (38 cm) FST (35 cm viewable)

Deflection angle 90 °

Dot Pitch 0.24 mm (Horizontal)

Resolution

Optimum resolution 800 x 600 @ 85 Hz

Maximum resolution 1024 x 768 @ 70 Hz

Active Display

Horizontal 267 ± 4 mm

Vertical 200 ± 4 mm

Synchronization

Horizontal 30 ~ 55 kHz

Vertical 50 ~ 120 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vp-p Positive at 75 Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

65 MHz

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Dimensions (WxDxH)

361 x 379.2 x 347 mm / 14.2 x 14.9 x 13.7 inch (After installation of Stand)

Weight

11.0 kg / 24.3 lbs

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor

and the computer systems will provide the best operating conditions and monitor settings. In most

cases, the monitor installation will proceed automatically, unless the user wishes to select alternate

settings.

Note: Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can

be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy

by switching your monitor into a low-power mode when it has not been used for a certain amount of

time. The monitor automatically returns to normal operation when you press a key on the keyboard. For

energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for

long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in

your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power-off mode

Power Indicator Green Green, Blinking

Power Consumption Less than 50 W (at the windows pattern) Less than 1 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the

screen will be adjusted automatically. However, if the signal differs, the screen may go blank while

the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 640 x 480 43.300 85.000 36.000 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of

the screen horizontally is called the Horizontal Cycle and the inverse

number of the Horizontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image

many times per second to display an image to the user. The

frequency of this repetition is called the Vertical Frequency or Refresh

Rate. Unit: Hz

General

Model Name SyncMaster 592V

Picture Tube

Type 15" (38 cm) FST (35 cm viewable)

Deflection angle 90 °

Dot Pitch 0.24 mm (Horizontal)

Resolution

Optimum resolution 800 x 600 @ 85 Hz

Maximum resolution 1024 x 768 @ 70 Hz

Active Display

Horizontal 267 ± 4 mm

Vertical 200 ± 4 mm

Synchronization

Horizontal 30 ~ 55 kHz

Vertical 50 ~ 120 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vp-p Positive at 75 Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

65 MHz

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Dimensions (WxDxH)

361 x 376 x 346 mm / 14.2 x 14.8 x 13.6 inch (After installation of Stand)

Weight

10.3 kg / 22.7 lbs

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor

and the computer systems will provide the best operating conditions and monitor settings. In most

cases, the monitor installation will proceed automatically, unless the user wishes to select alternate

settings.

Note: Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can

be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy

by switching your monitor into a low-power mode when it has not been used for a certain amount of

time. The monitor automatically returns to normal operation when you press a key on the keyboard. For

energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for

long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in

your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power-off mode

Power Indicator Green Green, Blinking

Power Consumption Less than 50 W (at the windows pattern) Less than 1 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the

screen will be adjusted automatically. However, if the signal differs, the screen may go blank while

the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 640 x 480 43.300 85.000 36.000 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of

the screen horizontally is called the Horizontal Cycle and the inverse

number of the Horizontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image

many times per second to display an image to the user. The

frequency of this repetition is called the Vertical Frequency or Refresh

Rate. Unit: Hz

General

Model Name SyncMaster 793S/793V/793SG/794MG

Picture Tube

Type 17" (43 cm) FSE (40.6 cm viewable)

Deflection angle 90 °

Dot Pitch 0.23 mm (Horizontal)

Resolution

Optimum resolution 1024 x 768 @ 85 Hz

Maximum resolution 1280 x 1024 @ 65 Hz

Active Display

Horizontal 312 ± 4 mm

Vertical 234 ± 4 mm

Synchronization

Horizontal 30 ~ 70 kHz

Vertical 50 ~ 160 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vp-p Positive at 75 Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

110 MHz

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Dimensions (WxDxH)

401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand)

Weight

13.8 kg / 30.4 lbs

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor

and the computer systems will provide the best operating conditions and monitor settings. In most

cases, the monitor installation will proceed automatically, unless the user wishes to select alternate

settings.

Note: Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can

be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy

by switching your monitor into a low-power mode when it has not been used for a certain amount of

time. The monitor automatically returns to normal operation when you press a key on the keyboard. For

energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for

long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in

your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power-off mode

Power Indicator Green Green, Blinking

Power Consumption Less than 55 W (at the windows pattern) Less than 1 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the

screen will be adjusted automatically. However, if the signal differs, the screen may go blank while

the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

VESA, 1024 x 768 68.700 85.000 94.500 +/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of

the screen horizontally is called the Horizontal Cycle and the inverse

number of the Horizontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image

many times per second to display an image to the user. The

frequency of this repetition is called the Vertical Frequency or Refresh

Rate. Unit: Hz

General

Model Name SyncMaster 794V

Picture Tube

Type 17" (43 cm) FSE (40.6 cm viewable)

Deflection angle 90 °

Dot Pitch 0.23 mm (Horizontal)

Resolution

Optimum resolution 1024 x 768 @ 85 Hz

Maximum resolution 1280 x 1024 @ 65 Hz

Active Display

Horizontal 312 ± 4 mm

Vertical 234 ± 4 mm

Synchronization

Horizontal 30 ~ 70 kHz

Vertical 50 ~ 160 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vp-p Positive at 75 Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

110 MHz

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Dimensions (WxDxH)

401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand)

Weight

12.8 kg / 28.2 lbs

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor

and the computer systems will provide the best operating conditions and monitor settings. In most

cases, the monitor installation will proceed automatically, unless the user wishes to select alternate

settings.

Note: Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can

be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy

by switching your monitor into a low-power mode when it has not been used for a certain amount of

time. The monitor automatically returns to normal operation when you press a key on the keyboard. For

energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for

long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in

your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power-off mode

Power Indicator Green Green, Blinking

Power Consumption Less than 55 W (at the windows pattern) Less than 1 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the

screen will be adjusted automatically. However, if the signal differs, the screen may go blank while

the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

VESA, 1024 x 768 68.700 85.000 94.500 +/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of

the screen horizontally is called the Horizontal Cycle and the inverse

number of the Horizontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image

many times per second to display an image to the user. The

frequency of this repetition is called the Vertical Frequency or Refresh

Rate. Unit: Hz

General

Model Name SyncMaster 783DF/793DF/793MG/788DF Plus

Picture Tube

Type 17" (43 cm) Flat (40.6 cm viewable)

Deflection angle 90 °

Dot Pitch 0.20 mm (Horizontal)

Resolution

Optimum resolution 1024 x 768 @ 85 Hz

Maximum resolution 1280 x 1024 @ 65 Hz

Active Display

Horizontal 312 ± 4 mm

Vertical 234 ± 4 mm

Synchronization

Horizontal 30 ~ 70 kHz

Vertical 50 ~ 160 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vp-p Positive at 75 Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

110 MHz

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz

Dimensions (WxDxH)

401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand)

Weight

14.3 kg / 31.5 lbs

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor

and the computer systems will provide the best operating conditions and monitor settings. In most

cases, the monitor installation will proceed automatically, unless the user wishes to select alternate

settings.

Note: Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can

be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy

by switching your monitor into a low-power mode when it has not been used for a certain amount of

time. The monitor automatically returns to normal operation when you press a key on the keyboard. For

energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for

long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in

your computer. Use the software utility installed on your computer to set up this feature.

State Normal Operation Power-off mode

Power Indicator Green Green, Blinking

Power Consumption Less than 55 W (at the windows pattern) Less than 1 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the

screen will be adjusted automatically. However, if the signal differs, the screen may go blank while

the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

VESA, 1024 x 768 68.700 85.000 94.500 +/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of

the screen horizontally is called the Horizontal Cycle and the inverse

number of the Horizontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image

many times per second to display an image to the user. The

frequency of this repetition is called the Vertical Frequency or Refresh

Rate. Unit: Hz

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care center.

North America

U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com

CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca

MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx

Latin America

ARGENTINE 0800-333-3733 http://www.samsung.com/ar

BRAZIL 4004-0000 http://www.samsung.com/br

CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl

COLOMBIA 01-8000112112 http://www.samsung.com.co

COSTA RICA 0-800-507-7267 http://www.samsung.com/latin

ECUADOR 1-800-10-7267 http://www.samsung.com/latin

EL SALVADOR 800-6225 http://www.samsung.com/latin

GUATEMALA 1-800-299-0013 http://www.samsung.com/latin

JAMAICA 1-800-234-7267 http://www.samsung.com/latin

PANAMA 800-7267 http://www.samsung.com/latin

PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin

REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin

TRINIDAD & TOBAGO 1-800-7267-864 http://www.samsung.com/latin

VENEZUELA 0-800-100-5303 http://www.samsung.com/latin

Europe

SyncMaster 591V/591S/592V/793V/794V/793DF/793S/783DF

BELGIUM 02 201 2418 http://www.samsung.com/be

CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz

DENMARK 70 70 19 70 http://www.samsung.com/dk

FINLAND 030-6227 515 http://www.samsung.com/fi

FRANCE 3260 SAMSUNG(7267864)

(€ 0,15/min) http://www.samsung.com/fr

GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de

HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu

ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it

LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu

NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.samsung.com/nl

NORWAY 815-56 480 http://www.samsung.com/no

POLAND 0 801 801 881 http://www.samsung.com/pl

PORTUGAL 80 8 200 128 http://www.samsung.com/pt

REPUBLIC OF IRELAND 0818 717 100 http://www.samsung.com/uk

SLOVAKIA 0800-SAMSUNG (7267864) http://www.samsung.com/sk

SPAIN 902 10 11 30 http://www.samsung.com/es

SWEDEN 0771-400 200 http://www.samsung.com/se

SWITZERLAND 0800-7267864 http://www.samsung.com/ch

U.K 0870 SAMSUNG (7267864) http://www.samsung.com/uk

CIS

ESTONIA 800-7267 http://www.samsung.ee

LATVIA 800-7267 http://www.samsung.com/lv

LITHUANIA 8-800-77777 http://www.samsung.lt

KAZAKHSTAN 8 800 080 1188 http://www.samsung.kz

RUSSIA 8-800-200-0400 http://www.samsung.ru

UKRAINE 8-800-502-0000 http://www.samsung.com/ur

UZBEKISTAN 140-1234 http://www.samsung.uz

Asia Pacific

AUSTRALIA 1300 362 603 http://www.samsung.com/au

CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn

HONG KONG 3698-4698 http://www.samsung.com/hk

INDIA 3030 8282, 1800 1100 11 http://www.samsung.com/in

INDONESIA 0800-112-8888 http://www.samsung.com/id

JAPAN 0120-327-527 http://www.samsung.com/jp

MALAYSIA 1800-88-9999 http://www.samsung.com/my

PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph

SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg

THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th

TAIWAN 0800-329-999 http://www.samsung.com/tw

VIETNAM 1 800 588 889 http://www.samsung.com/vn

Middle East & Africa

SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za

U.A.E 800SAMSUNG (7267864)

8000-4726 http://www.samsung.com/mea

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the

higher the resolution. The distance between two dots of the same color is called the 'Dot

Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image

for the user. The frequency of this repetition per second is called the Vertical Frequency or

Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally

is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal

Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom sequentially is called the

Non-Interlace method while showing odd lines and then even lines in turn is called the

Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a

clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer

and the monitor to exchange information automatically. This monitor follows the international

standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called the

'resolution'. This number shows the accuracy of the display. A high resolution is good for

performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1024 X 768, this means the screen is composed of 1024

horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).

Authorit

Information in this document is subject to change without notice.

2007 Samsun

Electronics Co., Ltd. All ri

hts reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics

Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and

Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are

registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and

logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other

product names mentioned herein may be the trademarks or registered trademarks of their

respective owners.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care center.

North America

U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com

CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca

MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx

Latin America

ARGENTINE 0800-333-3733 http://www.samsung.com/ar

BRAZIL 4004-0000 http://www.samsung.com/br

CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl

COLOMBIA 01-8000112112 http://www.samsung.com.co

COSTA RICA 0-800-507-7267 http://www.samsung.com/latin

ECUADOR 1-800-10-7267 http://www.samsung.com/latin

EL SALVADOR 800-6225 http://www.samsung.com/latin

GUATEMALA 1-800-299-0013 http://www.samsung.com/latin

JAMAICA 1-800-234-7267 http://www.samsung.com/latin

PANAMA 800-7267 http://www.samsung.com/latin

PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin

REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin

TRINIDAD & TOBAGO 1-800-7267-864 http://www.samsung.com/latin

VENEZUELA 0-800-100-5303 http://www.samsung.com/latin

Europe

BELGIUM 02 201 2418 http://www.samsung.com/be

SyncMaster 591SG/594MG/794MG/793SG

CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz

DENMARK 70 70 19 70 http://www.samsung.com/dk

FINLAND 030-6227 515 http://www.samsung.com/fi

FRANCE 3260 SAMSUNG(7267864)

(€ 0,15/min) http://www.samsung.com/fr

GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de

HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu

ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it

LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu

NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.samsung.com/nl

NORWAY 815-56 480 http://www.samsung.com/no

POLAND 0 801 801 881 http://www.samsung.com/pl

PORTUGAL 80 8 200 128 http://www.samsung.com/pt

REPUBLIC OF IRELAND 0818 717 100 http://www.samsung.com/uk

SLOVAKIA 0800-SAMSUNG (7267864) http://www.samsung.com/sk

SPAIN 902 10 11 30 http://www.samsung.com/es

SWEDEN 0771-400 200 http://www.samsung.com/se

SWITZERLAND 0800-7267864 http://www.samsung.com/ch

U.K 0870 SAMSUNG (7267864) http://www.samsung.com/uk

CIS

ESTONIA 800-7267 http://www.samsung.ee

LATVIA 800-7267 http://www.samsung.com/lv

LITHUANIA 8-800-77777 http://www.samsung.lt

KAZAKHSTAN 8 800 080 1188 http://www.samsung.kz

RUSSIA 8-800-200-0400 http://www.samsung.ru

UKRAINE 8-800-502-0000 http://www.samsung.com/ur

UZBEKISTAN 140-1234 http://www.samsung.uz

Asia Pacific

AUSTRALIA 1300 362 603 http://www.samsung.com/au

CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn

HONG KONG 3698-4698 http://www.samsung.com/hk

INDIA 3030 8282, 1800 1100 11 http://www.samsung.com/in

INDONESIA 0800-112-8888 http://www.samsung.com/id

JAPAN 0120-327-527 http://www.samsung.com/jp

MALAYSIA 1800-88-9999 http://www.samsung.com/my

PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph

SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg

THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th

TAIWAN 0800-329-999 http://www.samsung.com/tw

VIETNAM 1 800 588 889 http://www.samsung.com/vn

Middle East & Africa

SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za

U.A.E 800SAMSUNG (7267864)

8000-4726 http://www.samsung.com/mea

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the

higher the resolution. The distance between two dots of the same color is called the 'Dot

Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image

for the user. The frequency of this repetition per second is called the Vertical Frequency or

Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally

is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal

Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom sequentially is called the

Non-Interlace method while showing odd lines and then even lines in turn is called the

Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a

clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer

and the monitor to exchange information automatically. This monitor follows the international

standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called the

'resolution'. This number shows the accuracy of the display. A high resolution is good for

performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1024 X 768, this means the screen is composed of 1024

horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).

Green

The Green CDT monitor has adopted a Well-Being CDT that is coated with a Vital & Pure coating,

which radiates far infrared and anion.

MagicGreen is different from Green. They have different functions.

There is no sterilization/deodorization function.

Vital

Coating

Radiates far infrared and anion by applying a specialized ceramic on the

surface of the CDT funnel.

Authorit

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics

Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and

Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are

registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and

logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other

product names mentioned herein may be the trademarks or registered trademarks of their

respective owners.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care center.

North America

U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com

CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca

MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx

Latin America

ARGENTINE 0800-333-3733 http://www.samsung.com/ar

BRAZIL 4004-0000 http://www.samsung.com/br

CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl

COLOMBIA 01-8000112112 http://www.samsung.com.co

COSTA RICA 0-800-507-7267 http://www.samsung.com/latin

ECUADOR 1-800-10-7267 http://www.samsung.com/latin

EL SALVADOR 800-6225 http://www.samsung.com/latin

GUATEMALA 1-800-299-0013 http://www.samsung.com/latin

JAMAICA 1-800-234-7267 http://www.samsung.com/latin

PANAMA 800-7267 http://www.samsung.com/latin

PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin

REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin

TRINIDAD & TOBAGO 1-800-7267-864 http://www.samsung.com/latin

VENEZUELA 0-800-100-5303 http://www.samsung.com/latin

Europe

BELGIUM 02 201 2418 http://www.samsung.com/be

SyncMaster 793MG/788DF Plus

CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz

DENMARK 70 70 19 70 http://www.samsung.com/dk

FINLAND 030-6227 515 http://www.samsung.com/fi

FRANCE 3260 SAMSUNG(7267864)

(€ 0,15/min) http://www.samsung.com/fr

GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de

HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu

ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it

LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu

NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.samsung.com/nl

NORWAY 815-56 480 http://www.samsung.com/no

POLAND 0 801 801 881 http://www.samsung.com/pl

PORTUGAL 80 8 200 128 http://www.samsung.com/pt

REPUBLIC OF IRELAND 0818 717 100 http://www.samsung.com/uk

SLOVAKIA 0800-SAMSUNG (7267864) http://www.samsung.com/sk

SPAIN 902 10 11 30 http://www.samsung.com/es

SWEDEN 0771-400 200 http://www.samsung.com/se

SWITZERLAND 0800-7267864 http://www.samsung.com/ch

U.K 0870 SAMSUNG (7267864) http://www.samsung.com/uk

CIS

ESTONIA 800-7267 http://www.samsung.ee

LATVIA 800-7267 http://www.samsung.com/lv

LITHUANIA 8-800-77777 http://www.samsung.lt

KAZAKHSTAN 8 800 080 1188 http://www.samsung.kz

RUSSIA 8-800-200-0400 http://www.samsung.ru

UKRAINE 8-800-502-0000 http://www.samsung.com/ur

UZBEKISTAN 140-1234 http://www.samsung.uz

Asia Pacific

AUSTRALIA 1300 362 603 http://www.samsung.com/au

CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn

HONG KONG 3698-4698 http://www.samsung.com/hk

INDIA 3030 8282, 1800 1100 11 http://www.samsung.com/in

INDONESIA 0800-112-8888 http://www.samsung.com/id

JAPAN 0120-327-527 http://www.samsung.com/jp

MALAYSIA 1800-88-9999 http://www.samsung.com/my

PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph

SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg

THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th

TAIWAN 0800-329-999 http://www.samsung.com/tw

VIETNAM 1 800 588 889 http://www.samsung.com/vn

Middle East & Africa

SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za

U.A.E 800SAMSUNG (7267864)

8000-4726 http://www.samsung.com/mea

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the

higher the resolution. The distance between two dots of the same color is called the 'Dot

Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image

for the user. The frequency of this repetition per second is called the Vertical Frequency or

Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally

is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal

Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom sequentially is called the

Non-Interlace method while showing odd lines and then even lines in turn is called the

Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a

clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer

and the monitor to exchange information automatically. This monitor follows the international

standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called the

'resolution'. This number shows the accuracy of the display. A high resolution is good for

performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1024 X 768, this means the screen is composed of 1024

horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).

MagicGreen

The MagicGreen CDT monitor has adopted a Well-Being CDT that is coated with a Vital &

Pure coating, which radiates far infrared and anion and provides antibacterial and deodorizing

effects.

zVital Coating Radiates far infrared and anion by applying a specialized ceramic on the

surface of the CDT funnel.

zPure Coating Provides antibacterial deodorizing effects by treating the surface with

photocatalyst TiO2 and Nano Silver.

Authorit

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics

Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and

Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are

registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and

logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other

product names mentioned herein may be the trademarks or registered trademarks of their

respective owners.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment) - Europe only

(Applicable in the European Union and other European countries with

separate collection systems)

This marking shown on the product or its literature, indicates that it should not

be disposed with other household wastes at the end of its working life. To

prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this

product, or their local government office, for details of where and how they

can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and

conditions of the purchase contract. This product should not be mixed with

other commercial wastes for disposal.

Samsung 591Sg Users Manual File

SyncMaster 794V 10246002

591SG 10254139

Navigation menu

Versions of this User Manual:

Views

Navigation