Samsung Scs 26Uc4 Users Manual
SCS-26UC4 to the manual 42a38412-ef84-4335-a0a3-6ca86c557fbe
2015-01-23
: Samsung Samsung-Scs-26Uc4-Users-Manual-281420 samsung-scs-26uc4-users-manual-281420 samsung pdf
Open the PDF directly: View PDF .
Page Count: 6
Download | |
Open PDF In Browser | View PDF |
5. Allow 3 - 5 minutes for the base station to complete the startup sequence and detect both its connections and available communications. The first time the base station is used, it may take as long as one hour for the initial GPS acquisition. Your Network Extender is ready for use when all four LEDs are solid blue. Note: The optional GPS antenna cable is required only when the external GPS antenna installation is necessary. CONFIRMING NETWORK EXTENDER OPERATION LED Function Description PWR Power Solid blue: normal No light: abnormal SYS System connected Solid blue: normal Blinking red: establishing an initial network connection Solid red: abnormal GPS GPS Signal Solid blue: normal (GPS signal is received) Blinking blue or red: while searching for GPS signal Solid red: abnormal (GPS signal cannot be received, the external GPS antenna is required)* WAN WAN (Ethernet connection) Solid blue: normal Blinking blue: data communication No light: abnormal * See “External GPS Antenna” in the User Guide. TROUBLESHOOTING FOR MORE INFORMATION What if my GPS LED is still red after one hour? • Refer to the Network Extender User Guide that came with your device. • Visit verizonwireless.com/support • Call Customer Service toll free at 800-9220204 or *611 from your Verizon Wireless mobile phone. If the GPS LED is still red after one hour, you need to relocate the GPS antenna to receive a stronger signal. See “External GPS Antenna” in the User Guide. How do I know my phone is connecting through the Network Extender? Verizon Wireless Network Extender Quick Start Guide When dialing #48 on your wireless phone, an announcement will tell you if you are within range of the Network Extender. In addition, you will hear a short double tone on your wireless phone whenever making or receiving a call. The tone is played at the beginning of the call. © 2009 Verizon Wireless. All rights reserved. Verizon Wireless is a trademark of Verizon Trademark Services LLC. EP68-00361A SCS-26UC4 BEFORE YOU BEGIN Power LED To use a Verizon Wireless Network Extender you need: • An always-on broadband Internet connection with a minimum speed of 300 kbps. • An available Ethernet port on either your broadband modem or a router connected to the modem. Note: If you are connecting your Network Extender to a router, please ensure that it supports Virtual Private Networking (VPN). Most routers support this functionality, but if you are unsure of your router’s capabilities, refer to the manual that came with your router. System LED GPS Antenna CONNECTING YOUR NETWORK EXTENDER Wireless Antenna 1. Heat Vents GPS Antenna Cable Power Cord DC12V Power Port GPS LED WAN LED WAN Port Near a window (if this is not possible, see “External GPS Antenna” in the User Manual) • At least two feet away from your router if it supports Wi-Fi 2. Connect one end of the included Ethernet cable to an open port on the router (1) and connect the other end to the WAN port located at the rear of the base station (2). 3. Plug the power supply connector into the DC 12V power port located at the rear of the base station (3). 4. Insert one end of the power cord into the power supply and then plug the other end into an available outlet (4). Power Supply Ethernet Cable • For best results, place the Network Extender in an elevated location, such as the top of a bookshelf or tall cabinet. Your Network Extender package should contain the components shown below: Network Extender The Network Extender needs to be located: BEFORE YOU BEGIN Power LED To use a Verizon Wireless Network Extender you need: • An always-on broadband Internet connection with a minimum speed of 300 kbps. • An available Ethernet port on either your broadband modem or a router connected to the modem. Note: If you are connecting your Network Extender to a router, please ensure that it supports Virtual Private Networking (VPN). Most routers support this functionality, but if you are unsure of your router’s capabilities, refer to the manual that came with your router. System LED GPS Antenna CONNECTING YOUR NETWORK EXTENDER Wireless Antenna 1. Heat Vents GPS Antenna Cable Power Cord DC12V Power Port GPS LED WAN LED WAN Port Near a window (if this is not possible, see “External GPS Antenna” in the User Manual) • At least two feet away from your router if it supports Wi-Fi 2. Connect one end of the included Ethernet cable to an open port on the router (1) and connect the other end to the WAN port located at the rear of the base station (2). 3. Plug the power supply connector into the DC 12V power port located at the rear of the base station (3). 4. Insert one end of the power cord into the power supply and then plug the other end into an available outlet (4). Power Supply Ethernet Cable • For best results, place the Network Extender in an elevated location, such as the top of a bookshelf or tall cabinet. Your Network Extender package should contain the components shown below: Network Extender The Network Extender needs to be located: BEFORE YOU BEGIN Power LED To use a Verizon Wireless Network Extender you need: • An always-on broadband Internet connection with a minimum speed of 300 kbps. • An available Ethernet port on either your broadband modem or a router connected to the modem. Note: If you are connecting your Network Extender to a router, please ensure that it supports Virtual Private Networking (VPN). Most routers support this functionality, but if you are unsure of your router’s capabilities, refer to the manual that came with your router. System LED GPS Antenna CONNECTING YOUR NETWORK EXTENDER Wireless Antenna 1. Heat Vents GPS Antenna Cable Power Cord DC12V Power Port GPS LED WAN LED WAN Port Near a window (if this is not possible, see “External GPS Antenna” in the User Manual) • At least two feet away from your router if it supports Wi-Fi 2. Connect one end of the included Ethernet cable to an open port on the router (1) and connect the other end to the WAN port located at the rear of the base station (2). 3. Plug the power supply connector into the DC 12V power port located at the rear of the base station (3). 4. Insert one end of the power cord into the power supply and then plug the other end into an available outlet (4). Power Supply Ethernet Cable • For best results, place the Network Extender in an elevated location, such as the top of a bookshelf or tall cabinet. Your Network Extender package should contain the components shown below: Network Extender The Network Extender needs to be located: 1HWZRUN([WHQGHU 3R O\ SS 6X U ZH (WKHUQHW&DEOH 3 RUG U& H RZ 5RXWHU 5. Allow 3 - 5 minutes for the base station to complete the startup sequence and detect both its connections and available communications. The first time the base station is used, it may take as long as one hour for the initial GPS acquisition. Your Network Extender is ready for use when all four LEDs are solid blue. Note: The optional GPS antenna cable is required only when the external GPS antenna installation is necessary. CONFIRMING NETWORK EXTENDER OPERATION LED Function Description PWR Power Solid blue: normal No light: abnormal SYS System connected Solid blue: normal Blinking red: establishing an initial network connection Solid red: abnormal GPS GPS Signal Solid blue: normal (GPS signal is received) Blinking blue or red: while searching for GPS signal Solid red: abnormal (GPS signal cannot be received, the external GPS antenna is required)* WAN WAN (Ethernet connection) Solid blue: normal Blinking blue: data communication No light: abnormal * See “External GPS Antenna” in the User Guide. TROUBLESHOOTING FOR MORE INFORMATION What if my GPS LED is still red after one hour? • Refer to the Network Extender User Guide that came with your device. • Visit verizonwireless.com/support • Call Customer Service toll free at 800-9220204 or *611 from your Verizon Wireless mobile phone. If the GPS LED is still red after one hour, you need to relocate the GPS antenna to receive a stronger signal. See “External GPS Antenna” in the User Guide. How do I know my phone is connecting through the Network Extender? Verizon Wireless Network Extender Quick Start Guide When dialing #48 on your wireless phone, an announcement will tell you if you are within range of the Network Extender. In addition, you will hear a short double tone on your wireless phone whenever making or receiving a call. The tone is played at the beginning of the call. © 2009 Verizon Wireless. All rights reserved. Verizon Wireless is a trademark of Verizon Trademark Services LLC. EP68-00361A SCS-26UC4 5. Allow 3 - 5 minutes for the base station to complete the startup sequence and detect both its connections and available communications. The first time the base station is used, it may take as long as one hour for the initial GPS acquisition. Your Network Extender is ready for use when all four LEDs are solid blue. Note: The optional GPS antenna cable is required only when the external GPS antenna installation is necessary. CONFIRMING NETWORK EXTENDER OPERATION LED Function Description PWR Power Solid blue: normal No light: abnormal SYS System connected Solid blue: normal Blinking red: establishing an initial network connection Solid red: abnormal GPS GPS Signal Solid blue: normal (GPS signal is received) Blinking blue or red: while searching for GPS signal Solid red: abnormal (GPS signal cannot be received, the external GPS antenna is required)* WAN WAN (Ethernet connection) Solid blue: normal Blinking blue: data communication No light: abnormal * See “External GPS Antenna” in the User Guide. TROUBLESHOOTING FOR MORE INFORMATION What if my GPS LED is still red after one hour? • Refer to the Network Extender User Guide that came with your device. • Visit verizonwireless.com/support • Call Customer Service toll free at 800-9220204 or *611 from your Verizon Wireless mobile phone. If the GPS LED is still red after one hour, you need to relocate the GPS antenna to receive a stronger signal. See “External GPS Antenna” in the User Guide. How do I know my phone is connecting through the Network Extender? Verizon Wireless Network Extender Quick Start Guide When dialing #48 on your wireless phone, an announcement will tell you if you are within range of the Network Extender. In addition, you will hear a short double tone on your wireless phone whenever making or receiving a call. The tone is played at the beginning of the call. © 2009 Verizon Wireless. All rights reserved. Verizon Wireless is a trademark of Verizon Trademark Services LLC. EP68-00361A SCS-26UC4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : Yes XMP Toolkit : 3.1-702 Modify Date : 2008:12:09 11:31:50-08:00 Create Date : 2008:12:05 13:39:12-06:00 Metadata Date : 2008:12:09 11:31:50-08:00 Creator Tool : Adobe InDesign CS3 (5.0) Format : application/pdf Document ID : uuid:55700ee3-b846-4ab7-bfde-f05dc05ea665 Instance ID : uuid:91b23af8-9ba4-4e31-8e57-da2880fe131c Producer : Adobe PDF Library 8.0 Page Count : 6 Creator : Adobe InDesign CS3 (5.0)EXIF Metadata provided by EXIF.tools