Sangean Electronics 024 Bluetooth Module User Manual SPEC BM160 V1 3 20022012

Sangean Electronics Inc Bluetooth Module SPEC BM160 V1 3 20022012

User Manual

Product Specification Spec-BM160-V1.3 Page 1 of 7 www.sunitec.com.tw ® Product Features: • Bluetooth Spec. V2.1+EDR Compliant • Class 2 type Output Power • Support HSP ,HFP, A2DP and AVRCP Profiles • Integrated Switched-Mode Regulator • Integrated 150mA Battery Charger • Integrated Microphone bias • Integrated LED Driver • High-quality audio 95dB SNR on DAC playback • CVC Support for echo and Noise reduction • Support for 802.11 Co-existence • Size: 21mm x 13.5 mm x 2.35mm • Weight: 0.8g System Architecture BM160 Class 2 Multimedia Module CSR, BC57F687A05 Feb. 2012 Product Description: The BM160 is base on BlueCore5-Multimedia ROM QFN chipset from leading Bluetooth chipset supplier Cambridge Silicon Radio. BM160 interfaces a Bluetooth radio, baseband, DSP, high-quality audio codec, SMPS, LDOs, a battery charger and external EEPROM memory. BlueTunes ROM QFN uses advanced DSP features for the latest stereo enhancements and to improve audio quality; including SBC and MP3 decoder, support for FastStream(low battery codec) and 5-band EQ. The module and device firmware is fully compliant with the Bluetooth specification v2.1+EDR Applications: • Hands-free Car Kit • Stereo Headset • AV Headphones • Echo Cancellation • High Performance Mono Headsets • Wireless Speakers Specifications: Operating Frequency Band 2.4GHz ~ 2.48GHz unlicensed ISM band Bluetooth Specification V2.1+EDR Output Power Class Class 2 Operating Voltage 1.8V or 3.3V Audio Interface Analogue Dimension 21mm (L) x 13.5 (W) mm x 2.35mm (H) Specifications are subject to change without prior notice
Product Specification Spec-BM160-V1.3 Page 2 of 7 www.sunitec.com.tw ® Electrical Characteristics Absolute Maximum Rating Min Max Storage Temperature -40°C +85°C Supply Voltage, (V_CHG) -0.30V +6.5V Recommended Operating Conditions Min Max Operating Temperature Range -20°C +70°C Supply Voltage, (V_BAT) 2.7V 4.2V Supply Voltage, (V_CHG) 4.5V 6.0V Power Consumption Units Average SCO Connection HV3 (30ms interval sniff mode) mA TBD SCO Connection HV1 mA TBD ACL Data Transfer 115.2Kbps UART no traffic (Master) mA TBD ACL Data Transfer 115.2Kbps UART no traffic (Slave) mA TBD CODEC Microphone inputs and ADC/channel mA TBD DAC and loudspeaker driver, no signal/channel mA TBD Digital audio processing subsystem mA TBD VBAT = 4.2V; f = 2.441GHz; T=20°C RF Characteristics Receiver Units Min Typ Max Bluetooth Spec Sensitivity at 0.1% BER dBm - -90 -86 ≤-70 Maximum Receiver Signal dBm -20 -10 - ≥ -20 C/I Co-Channel dB - 6 11 ≤11 Adjacent Channel Selectivity C/I -1MHz dB - -6 0 ≤0 2nd Adjacent Channel Selectivity C/I -2MHz dB - -38 -30 ≤-30 3rd Adjacent Channel Selectivity C/I -3MHz dB - -45 -40 ≤-40 Image Rejection C/I dB - -16 -9 ≤-9 VBAT = 4.2V; f = 2.4441GHz; T=20°C Transmitter Units Min Typ Max Bluetooth Spec RF Output Power dBm 0 3 - -6 to +4 RF Power Control Range dB 16 24 - > 16 RF Power Range Control Resolution dB - 0.5 - - 20dB Bandwidth for Modulated Carrier KHz - 940 1000 <1000 2nd Adjacent Channel Power (+/- 2MHz) dBm - -36 -20 ≤-20 3rd Adjacent Channel Power (+/- 3MHz) dBm - -45 -40 ≤-40 VBAT = 4.2V; f = 2.4441GHz; T=20°C All specifications including pinouts and electrical specifications may be changed without prior notice
Product Specification Spec-BM160-V1.3 Page 3 of 7 www.sunitec.com.tw ® Pin Configurations PIN NO. NAME TYPE FUNCTION RE-MARK 1 AIO1 Bi-directional Programmable input/output line 2 AIO0 Bi-directional Programmable input/output line 3 RESET CMOS input with weak internal pull-up Reset if low. Input debounced so must be low for >5ms to cause a reset 4 GND GND Ground 5 PIO9 Bi-directional Programmable Input/Output Line 6 N/A 7 PIO11 Bi-directional Programmable Input/Output Line 8 PIO12 Bi-directional Programmable Input/Output Line 9 PIO13 Bi-directional Programmable Input/Output Line 10 PIO14 Bi-directional Programmable Input/Output Line 11 N/A 12 GND GND Ground 13 VDD Power 3.3V Supply For 3.3V Version VDD Power Connect to 1V8 For 1.8V Version 14 VDD_USB Power Positive Supply For UART/USB Port Connect to VDD 15 +1V8 Power +1.8V Supply 16 GND GND Ground 17 N/A 18 N/A 19 UART_RTS CMOS Output UART Request To Send (Active Low) 20 UART_CTS CMOS Input UART Clear To Send (Active Low) 21 UART_RX CMOS Input UART Data Input (Active High) 22 UART_TX CMOS Output UART Data Output (Active High) 23 N/A 24 N/A 25 TEST_EN For test purposes only, Leave unconnected 26 N/A 27 SPI_CSB CMOS Input Chip Select For Synchronous Serial Interface (Active Low) 28 SPI_MISO CMOS Output Serial Peripheral Interface Data Output 29 SPI_CLK CMOS Input Serial Peripheral Interface Data Clock 30 SPI_MOSI CMOS Output Serial Peripheral Interface Data Input 31 VRE_IN Analogue Take high to enable switch-mode regulator 32 VDD_BAT Battery terminal +ve Lithium ion/polymer battery positive terminal. Battery charger output and input to switch-mode regulator 33 GND GND Ground 34 VDD_CHG Charger input Lithium ion/polymer battery charger input 35 LED1 Open drain output LED Driver 36 LED0 Open drain output LED Driver 37 GND GND Ground 38 SPK_L_N Analogue Speaker output negative, left 39 SPK_L_P Analogue Speaker output positive, left 40 SPK_R_N Analogue Speaker output negative, right 41 SPK_R_P Analogue Speaker output positive, right 42 GND_S Analogue GND Analogue Ground 43 MIC_BIAS Analogue Microphone bias 44 MIC_B_P Analogue Microphone input positive, right 45 MIC_B_N Analogue Microphone input negative, right 46 MIC_A_P Analogue Microphone input positive, left 47 MIC_A_N Analogue Microphone input negative, left 48 GND GND Ground 49 PIO0 Bi-directional Programmable Input/Output Line 50 PIO1 Bi-directional Programmable Input/Output Line 51 PIO2 Bi-directional Programmable Input/Output Line 52 PIO3 Bi-directional Programmable Input/Output Line 53 PIO4 Bi-directional Programmable Input/Output Line 54 PIO5 Bi-directional Programmable Input/Output Line 55 PIO6 Bi-directional Programmable Input/Output Line 56 PIO7 Bi-directional Programmable Input/Output Line 57 PIO8 Bi-directional Programmable Input/Output Line 58 GND GND Ground 59 RF-IN RF RF Interface 60 GND GND Ground
Product Specification Spec-BM160-V1.3 Page 4 of 7 www.sunitec.com.tw ® Recommended Layout patterns: 11 NC6 NC13 NC 14 NC 15 +1V8 16 GND 17 NC 18 NC 1.AIO1 2.AIO0 3.RESET 4.GND 5.PIO9 6.N/A 7.PIO11 8.PIO12 9.PIO13 10.PIO14 11.N/A 12.GND 13.VDD 14.VDD_USB 15.+1V8 16.GND 17.N/A 18.N/A 19.UART_RTS 20.UART_CTS 21.UART_RX 22.UART_TX 23.N/A 24.N/A 25.TEST_EN 26.N/A 27.SPI_CSB 28.SPI_MISO 29.SPI_CLK 30.SPI_MOSI 31.VRE_IN 32.VDD_BAT 33.GND 34.VDD_CHG 35.LED1 36.LED0 37.GND 38.SPK_L_N 39.SPK_L_P 40.SPK_R_N 41.SPK_R_P 42.GND_S 43.MIC_BIAS 44.MIC_B_P 45.MIC_B_N 46.MIC_A_P 47.MIC_A_N 48.GND 49.PIO0 50.PIO1 51.PIO2 52.PIO3 53.PIO4 54.PIO5 55.PIO6 56.PIO7 57.PIO8 58.GND 59.RF 60 GND
Product Specification Spec-BM160-V1.3 Page 5 of 7 www.sunitec.com.tw ® Recommended Reflow Temperature Profile: Key features of the profile: -Initial Ramp=1-2.5℃/sec to 175℃ equilibrium -Equilibrium time=60 to 80 seconds -Ramp to Maximum temperature (250℃)=3℃/sec Max -Time above liquidus temperature(217℃): 45 - 90 seconds -Device absolute maximum reflow temperature: 250℃ MAC Address: Each Module has his MAC Address 001d df XXXXXX Concerning the dimension of the tab，only printing the last six letters of the LAP on the module. xxxxxx5.0 mm13.0 mm The tab code pastes style:
Product Specification Spec-BM160-V1.3 Page 6 of 7 www.sunitec.com.tw ® QDL Certificate
Product Specification Spec-BM160-V1.3 Page 7 of 7 www.sunitec.com.tw ® Ordering Information No Items Ordering Code (Class 2) Description 2 BlueTunes Module BM160 3 BlueTunes Module Test Kit BM160 TK Test kit to fit CSR Casira Kit 4 Titan is Antenna 2010B4844-01 GigaAnt 2.4GHz Swivel SMA Antenna BM160S Test Kit Titanis Antenna Document References References Version Specifications of the Bluetooth System V2.1+EDR, 26 July 2007 BlueTunes ROM QFN Data Sheet CS-122312-DSP1 23 Oct 2008 Document History Revision Date History Draft V0.1 2009-10-22 V1.0 2009-11-30 Official release V1.1 2009-12-01 V1.2 2009-12-02 Swap LED0 and LED1 V1.3 2012-02-20 Add BQB Certificate Contact Information Sunitec Enterprise Co., Ltd. Head Office: 3F.,No.98-1,Mincyuan Rd Sindian City, Taipei County 231,Taiwan Tel: 886-2-82191696 Fax: 886-2-82191676 China Factory: No.2,Qilin Road 2,Run Tang Ind., Dan-Keng Village Fu Ming Community, Guan-lan Town, BaoAn District, Shenzhen GuangDong China Tel: 86-755-29802983 Fax: 86-755-29802984 E-mail:sales@sunitec-cn.com & project@sunitec-cn.com http://www.sunitec-cn.com
Notice: The user should not modify or change this equipment without written approval form SANGEAN ELECTRONICS INC. Modification could void authority to use this equipment. Label for end product must include “Contains FCC ID: BYG024” or “A RF transmitter inside, FCC ID: BYG024”. FCC ID Label Graph: FCC ID: BYG024 Model: BM160-CB1-SJ This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: If the product is too small to make so many text labels, only need to indicate the FCC ID number on the label, but the above text will be printed in the manual or packaging box. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. The module has been regulatory approved for integrations which meet the following conditions: 1. The radio integration is embedded 2. The antenna must be installed such that 20 cm is maintained between the antenna and users 3. The ‘Type’ and ‘Gain’ of the antenna selected for the integration of the external antenna must meet the requirements as detailed in section. Used outside of these conditions will trigger re-approval.

Navigation menu