Sansui HDLCD2600A User Manual LCD TELEVISION Manuals And Guides L0811658

SANSUI LCD Television Manual L0811658 SANSUI LCD Television Owner's Manual, SANSUI LCD Television installation guides

TESCO SP-4291 L0811658

User Manual: Sansui HDLCD2600A HDLCD2600A SANSUI LCD TELEVISION - Manuals and Guides View the owners manual for your SANSUI LCD TELEVISION #HDLCD2600A. Home:Electronics Parts:Sansui Parts:Sansui LCD TELEVISION Manual

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

O .E.'S

!.f SAN

26" WIDE TFT LCD TELEVISION
WITH DIGITAL TUNER

HDLCD2600A
,L_I_T¢oo_

D ! G ! T A L

If you purchase

H__r

.,.... ,..,........,_o,_,
...... o

a universal remote control from your local retailer, please contact the remote manufac-

ATTENTION

When shipped from the factory, the Signal Type option is set to the "Cable" (Cable Television) mode. If
not using Cable TV, set this menu Air/Cable
option to theMODE
"Air" position.
SELECTION

turer for the required

programming

code.

IF CONTACT WITH CUSTOMER SERVICE IS REQUIRED
PLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALL

CUSTOMER

SERVICE
ORION

FOR INFORMATION

ON OUR OTHER

- 1-800-289-0980

WEBSITE

PRODUCTS,

PLEASE

VISIT

OUR WEBSITE

www.orionsalesinc.com
Before operating

the unit, please read this manual thoroughly.

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.

WARNING:
CAUTION:

WARNING:

CAUTION:

The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT BLADE EXPOSURE.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/-I-V technician for help.
Changes or modifications not expressly approved by the party responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.

The lamp(s) within this product contain mercury.
Disposal should be in compliance with local, state or
federal laws.

The lightning flash with arrowhead
symbol, within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product's enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock.

Location of the required Marking
The rating sheet and the safety caution are
on the rear of the unit.

IMPORTANT

SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a clean dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade and the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician to replace the obsolete receptacle.

10) Protect the power cord from being walked on or pinched particularly at plug, and the point where it exits
from the apparatus.
11) Only use attachments/accessories

specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
PORTABLE CART WARNING
(symbol provided by RETAC)

13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug
damage, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.

$3126A

15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as vases,
should not be placed on the apparatus.
16) An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

IMPORTANT SAFETY INSTRUCTIONS
19) If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of
the National Electrical Code, ANSl/NFPA 70, provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE

ANTENNA LEAD
IN WIRE

GROUND
CLAMP.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS

NEC-NATIONAL
$2898A

ELECTRICAL CODE

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

20) When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21) Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
22) When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.
23) Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
24) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker
overheating and fire.
25) This reminder is provided to call the cable TV system installer's attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.

IMPORTANT SAFETY INSTRUCTIONS
CONDENSATION
Moisture will form in the operating section of the player if the player is brought from coot surroundings into a
warm room or if the temperature of the room rises suddenly. When this happens, player's performance will be
impaired. To prevent this, let the player stand in its new surroundings for about an hour before switching it on, or
make sure that the room temperature rises gradually.
Condensation may also form during the summer if the player is exposed to the breeze from an air conditioner. In
such cases, change the location of the player.
HOW TO HANDLE THE LCD PANEL
• Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur.
• If the LCD panel is broken, make absolutely sure that you do not touch the liquid in the panel. This may cause
skin inflammation.
If the liquid gets in your mouth, immediately gargle and consult with your doctor. Also, if the liquid gets in your
eyes or touches your skin, consult with your doctor after rinsing for at least 15 minutes or longer in clean water.
Possible Adverse Effects on LCD Panel: If a fixed (non-moving) pattern remains on the LCD Panel for
long periods of time, the image can become permanently engrained in the LCD Panel and cause subtle but
permanent ghost images. This type of damage is NOT COVERED BYYOUR WARRANTY. Never leave your
LCD Panel on for long periods of time while it is displaying the following formats or images:
• Fixed Images, such as stock tickers, video game patterns, TV station Iogos, and websites.
• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on
a normal (4:3) display (black bars at top and bottom of screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (black bars on left and right sides of screen).
The following symptoms are not signs of malfunction but technical limitation. Therefore we disclaim any
responsibility for these symptoms.
• LCD Panels are manufactured using an extremely high level of precision technology, however sometimes
parts of the screen may be missing picture elements or have luminous spots.
This is not a sign of a malfunction.
• Do not install the LCD Panel near electronic equipment that is susceptible to electromagnetic waves. Some
equipment placed too near this unit may cause interference.
• Effect on infrared devices -There may be interference while using infrared devices such as infrared cordless
headphones.

SAFETY PRECAUTIONS
The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause
overheating.
Do not block ventilation holes, or set up near radiators. Do not place in direct sunshine. When placing on a shelf
leave 10 cm (4 inches) free space around the entire unit.

10cmt

Notes when mounting the LCD TV on a wall
• When installing the unit on a wall, allow at least 6 cm (2 1/2
inches) clearance between the rear of the LCD TV and the wall.
Clearance of less than 6 cm (2 1/2 inches) will obstruct the vents
and may cause the interior of the unit to overheat, resulting in
damage to the unit.
• If the unit is to be mounted on the wall, contact the retailer where
you purchased the LCD TV for advice, and have the equipment
professionally installed. Incomplete or improper installation may
cause injury to you, and/or damage to the LCD TV.
• Bracket holes: To attach a wall mounting bracket (not supplied)
remove the screws and attached where indicated in the drawing
below.

Contents

IMPORTANT SAFETY INSTRUCTIONS .......................................
SAFETY PRECAUTIONS ..............................................................
Contents ........................................................................................
Features ........................................................................................
Power source .................................................................................
Parts and functions ........................................................................
Remote control ..............................................................................
Antenna connections ...................................................................
Cable TV connections ..................................................................
Connections to other equipment ..................................................
Setting the language ....................................................................

3
5
6
7
7
8
9
10
11
12
17

Memorizing channels ...................................................................
TV operation ................................................................................
Labeling channels ........................................................................
Labeling video inputs ...................................................................
Setting the V-Chip ........................................................................
Closed Caption ............................................................................
CC advanced ...............................................................................
Adjusting the picture preference ..................................................
Picture control adjustment ...........................................................
Selecting the color temperature ...................................................
Setting the picture size ................................................................
Film Mode ....................................................................................
Picture control adjustment in the PC mode .................................
DNR .............................................................................................
Sound control adjustment ............................................................
Selecting Stereo/Second Audio Program (SAP) ..........................
Selecting the audio language ......................................................
Selecting the HDMI audio input source .......................................
Turning off the built-in speakers ...................................................
Adjusting the back lighting ...........................................................
Setting the Auto Shut Off .............................................................
Resetting your settings ................................................................
Reception disturbances ...............................................................

17
18
19
20
20
21
22
22
23
23
23
24
24
25
25
25
25
26
26
26
26
26
27

Troubleshooting ...........................................................................
Specifications ..............................................................................
LIMITED WARRANTY .................................................................

28
29
30

Features
• Integrated Digital Tuner -You can view digital broadcasts without using a Digital TV Set-Top Box.
• Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for
hearing impaired viewers.
• Picture Adjustments
Using The Remote Control - The On-Screen display allows precise remote control
adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.
• Programmable
TV Sleep Timer - Operable from the remote control, the LCD -IV can be programmed for up
to 240 minutes to turn off automatically.
• V-Chip - The V-Chip function can read the rating of a broadcast program or movie content if the program is
encoded with this information. V-chip will allow you to set a restriction level.
• Digital Audio Jack (Coaxial) - When a component with a built-in Dotby Digital decoder is connected, Dolby
Digital sound can produce the effect of being in a movie theater or a concert hall.
• S-Video/Component
Video Jacks - A VCR, DVD player, satellite receiver or other audio/video component
can be connected to this unit.
• Video Input Jacks - This unit is equipped with 3 types of video input jacks. The component video in jacks and
S-video in jack enable you to watch the DVD player or the video devices with high quality picture.
• On-Screen 3 Language Display - You can select one of 3 languages, English, French or Spanish for onscreen programming.
* Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of
Dolby Laboratories.
* HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.

Power source
TO USE AC POWER
1. Connect the AC cord plug into this unit's AC INPUT jack.
2. Connect the AC cord into an AC outlet.

AC Outlet
Wider Hole

AC 120V, 60Hz

AC cord (supplied)

NOTE:
• Please make sure to insert the cord securely at both the LCD TV and the wall outlet.
• The AC cord has a grounding-type AC line plug. If the supplied AC cord does not match your AC outlet,
contact a qualified electrician, do not defeat the purpose of a grounding plug.
WARNING:
• DO NOT CONNECTTHIS UNITTO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC
CORD. THIS COULD CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE.
• DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE DISPLAYED. THIS COULD CAUSE
FIRE, ELECTRICAL SHOCK, OR DAMAGE.
CAUTION:
• WHEN THIS UNIT IS NOT USED FOR A LONG TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF
SAFETY, BE SURE TO UNPLUG IT FROM THE AC OUTLET.
• DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRICAL
SHOCK.
• IFYOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED ONE IS
RECOMMENDED. CONTACT CUSTOMER SERVICE AT 1-800-289-0980.

Parts and functions
Front

Top

POWER
button

VOLUME
+/- buttons

CHANNEL
A/V buttons

INPUT/ENTER
button

Remote sensor

POWER indicator
Red: Standby
Green: On

i "_'-__

RF (ANT) IN jack

D --

VAR (VARIABLE)

AUDIO OUT jacks

---

COAXIAL DIGITAL AUDIO OUT jack
HDMI-2 IN jack

HDMI-1 IN jack

iB4]_FT%_

i .....
Rear

[]

'_ii_

side

-- PC MONITORIN jack

i,,_,_j AUDIO _
'

PC/HDMI-1

AVl IN jacks

_
,_....... _11

AUDIO jack

(VIDEO/S-VIDEO/AUDIO

_
_,,_G_q-_-'
_t_

AUDIO (L/R) jacks
(for COMPONENT IN and AV2 VIDEO IN)

i _COM_ON_ _=-

AV2 VIDEO IN jack

COMPONENT
AC INPUT

To display the menu screen.
Press MENU button to display the menu screen.
CHANNEL
A/V buttons, VOLUME +/- buttons and ENTER
during the menu screen operations.

(L/R))

button

IN jacks

jack

can be used to select

the desired

setting

Remote control
1
2

9
10

13
14

6.CH (CHANNEL) +/-/CURSOR
• / • Buttons
- Used to operate the menu functions of the LCD
TV, and to change the channels of the LCD TV.
7. MENU Button - Use to display the On-Screen
menu function.
8. MUTE Button - To turn off the sound, press this
button once. The LCD TV will be silenced and
the symbol "Mute" will appear on the screen. The
muting feature can be released by pressing the
MUTE button again or one of the VOL (VOLUME)
+ or - buttons.

1. POWER Button - Used to turn the power on/off to
the LCD -IV.
2.SLEEP Button -To set the LCD -IV to turn off
after a preset amount of time, use the SLEEP
button on the remote control.

9. DISPLAY Button - When you press this button,
the current information will be displayed on a
screen. To remove the display from the screen,
press this button again.
10. PICTURE SIZE Button - Used to change the
picture size.
11. INPUT SELECT Button - Use to change the
external input.
12. RECALL Button -This button allows you to go
back to the previous channel selected by just
pressing the RECALL button. Press this button
again to return to the channel you were watching.

3. Direct Channel Selection Buttons (0-9) - Allows
direct access to any channel of the LCD -IV.
4.- Button -This button is the "-" button used
when selecting digital channels. Also can display
the current channel number when viewing the
program.
5. RESET Button - Press to reset the On-Screen
picture adjustments to their factory preset positions.
To use this function, select "Picture" or "Audio" in
the menu screen, then press this button.

13. CCD Button - Used to display the Closed Caption
menu screen.
14. ENTER Button - Use to enter or select
information for On-Screen operations. Also can
display the current channel number when viewing
the program.
15.VOL (VOLUME) + / -/CURSOR
• / I_ Buttons
- Used to operate the menu functions of the LCD
TV. Press the _ button to increase, or the • button
to decrease the sound level.

15
16

16. EXIT Button - Press to remove setup menu.
Before using the remote control, batteries must first be installed.

HOW TO INSTALL BATTERIES
1. Open the battery compartment

cover.

2. Install two "AA" batteries (supplied).

3. Replace the battery compartment cover.

Use two "AA" size batteries. The batteries may last
approximately one year depending on how much the
remote control is used. For best performance, it is
recommended that batteries should be replaced on a
yearly basis, or when the remote operation becomes
erratic. Do not mix old and new batteries or different
types.
BATTERY PRECAUTIONS
These precautions should be followed when using
batteries in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when
installing the batteries as indicated in the battery
compartment. Reversed batteries may cause
damage to the device.
• Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh
ones.
• If the device is not to be used for a long period of
time, remove the batteries to prevent damage or
injury from possible battery leakage.
• Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture. (Follow
battery manufacturer's directions.)

Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your
antenna system. If you are using a Cable TV service, see page 11 for Cable TV connections.

Combination

VHF/UHF

Antenna

(Single

75 ohm cable or 300 ohm twin-lead

wire)

Connect the 75 ohm cable from the combination
VHF/UHF antenna to the antenna jack.

Antenna
Jack

Co
xia,
Cable

75 ohm

If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, the use of the 300-75 ohm
matching transformer may be necessary.

Antenna

Jack

Combination

300-75 ohm
Matching
Transformer

VHF/UHF

Antenna

(Separate

VHF and UHF 300 ohm twin-lead

Connect the UHF 300 ohm twin-lead wire to
the Combiner (not supplied). Connect the VHF
300 ohm twin-lead wire to the 300-75 ohm
Matching Transformer. Attach the Transformer to
the Combiner, then attach the Combiner to the
Antenna Jack.

300-75 ohm Matching Transformer
/
VHF 300 ohm

Antennajack

Separate

VHF/UHF

_l
UHF
Combiner

Antennas

Ifll
II1_

'
300 ohm

(75 ohm VHF cable and 300 ohm UHF twin-lead

wires)

Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the Combiner (not supplied).Attach
the Combiner to the Antenna Jack.
VHF 75 ohm

An2en a
Combiner

wires)

Cable TV connections
This TV has an extended tuning range and can tune most cable channels without using a Cable TV
Converter box. Some cable companies offer "premium pay channels" where the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device which is
generally provided by the Cable TV company.

For subscribers

to basic Cable TV service

r
75 ohm
Coaxial
Cable

Antenna
Jack

@,For subscribers

For basic Cable TV service not requiring a Converter/
Descrambler box, connect the 75 ohm Coaxial Cable directly
to the Antenna Jack on the back of the TV.

I®
to scrambled

Cable TV service

If you subscribe to a Cable TV service which requires the use of a Converter/Descrambler
the incoming 75 ohm Coaxial Cable to the Converter/Descrambler
box. Using another 75
Cable, connect the output jack of the Converter/Descrambler
box to the Antenna Jack on
connections shown below. Set the TV to the output channel of the Converter/Descrambler
3 or 4) and use the Converter/Descrambler
box to select channels.

box, connect
ohm Coaxial
the TV. Follow the
box (usually channel

Incoming
75 ohm
Cable TV

Antenna
Jack
D

Cable

For subscribers
channels

Converter/
Descrambler

to unscrambled

Cable TV service

75 °hm Cable t° TV

with scrambled

premium

If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require
the use of a Converter/Descrambler
box, you may wish to use a signal Splitter and an A/B Switch box (available
from the Cable TV company or an electronics supply store). Follow the connections shown below. With the
switch in the "B" position, you can directly tune any nonscrambled channels on your TV. With the switch in the
"A" position, tune your TV to the output of the Converter/Descrambler
box (usually channel 3 or 4) and use the
Converter/Descrambler
box to tune scrambled channels.

Incoming
75
ohm
Cable TV
Cable

=E_

Converter/
Descrambler

Splitte r

A/B Switch E

Antenna
Jack
B_ 75 ohm Cable to TV.

Connections to other equipment
The exact arrangement you use to interconnect various video and audio components to the LCD TV is
dependent on the model and features of each component. Check the Owner's Manual provided with each
component for the location of video and audio inputs and outputs.
The connection diagrams below are offered as suggestions. You may need to modify them to accommodate
your particular assortment of components. The diagrams are intended to show component video and audio
interconnections only.
To connect

the LCD TV to a VCR

Left side of the LCD TV

/__

To AV1 VIDEO/AUDIO

,i,uD,o
H

(L/R) IN

)

AudioNideocord
_1

))

(not supplied)//
To Audio/Video OUT

To connect

IDEO/AUDIO (L!

Pr _

the LCD TV to a VCR with an S-Video

cord

If you connect a VCR with a S-VIDEO cord to the S-VIDEO IN jack on the LCD TV, you must also connect the
audio cords to the AV1 AUDIO(L!R) IN jacks. The S-VIDEO cord only carries the video signal. The audio signal is
separate.
Left side of the LOD TV

To S-VIDEO IN

__J_L

To S-Video OUT

S-Video cord (not supplied)

[i"

]

Audio cord (not supplied)
To AV1 AUDIO (L!R) IN

To Audio OUT

NOTE:
• When the S-video cord and the video cord are connected to each jack at the same time, the S-video cord
takes precedence over the video cord.

Connections to other equipment
To connect the LCD TV to a DVD player/Satellite

receiver

If your DVD player or Satellite receiver has a S-Video out jack, connect cords as shown.
Left side of the LCD TV

To
IN cord (not supplied)
To S-Video OUT
@ S-VIDEO
S-Video

Oo_

J
I

____

Audio cord (not supplied)
To AV1 AUDIO (L/R) IN

To Audio OUT

To connect the LCD TV to a DVD player with component video
If your DVD player has component video out jacks, connect your LCD TV to a DVD player using a component
video cord. It can greatly enhance picture quality and performance.
Left side of the LCD TV
J

To AV2 AUDIO (L!R) IN
--_)

To Audio OUT

Audiocord(notsupplied)(_

COMPONENt,

....

]

Componentvideocord(notsupplied)PB_
PR
TO COMPONENT IN
To Component OUT
NOTE:
• Component Video inputs of the unit are for use with a device which outputs 480i/1080i interlaced signals and
480p/720p progressive signals.

Connections to other equipment
To connect the LCD TV to a DTV receiver/set-top
If you connect a DTV receiver/set-top
component video cord.

box

box, connect your LCD TV to a DTV receiver/set-top

box using a

Left side of the LCD TV
/

,v V, Op4

To AV2 AUDIO (L/R) IN

1_)

COMPONENt,

To Audio OUT

Audiocord(notsupplied)(_

0000

C0mp0nentvide0c0rd(n0tsupplied)
PB_
PR
TO COMPONENT IN
To Component OUT

To connect the LCD TV to an HDMI or a DVI device
The HDMI input receives digital audio and uncompressed video from an HDMI device or uncompressed digital
video from a DVI device.
When you connect to a DVI device with an HDMI-to-DVI adapter cable, it transfers only the video signal.
Separate analog audio cords are required.
Left side of the LCD TV

•, Dll

To HDMI-2 (or1) IN

To HDMI out

HDMI cable (type A connector)

W]'
PC
UONrrOR

(not supplied)

To HDMI-1 IN

I
I

HDMI device

HDMI - to - DVI adapter cable
(HDMI type A connector)
(not supplied)

DVI device

To PC/HDMI-1 AUDIO IN
PC/_-I_

@" 11

Audio cord (not supplied)
To DVI output
NOTE:
• If you connect an external component (cable box, satellite receiver, etc.) to this LCD TV using an HDMI cable
or a DVI to HDMI cable, the image will not display if the output resolution of the component is set to 480i. To
receive the picture you must change the output resolution on the external component.
Should you require further instruction, please contact the manufacturer of the external component.
• When you connect a DVI device, you must connect only with HDMI-1.

Connections to other equipment
To connect the LCD TV to a Game or a Camcorder
The LCD TV can also be used as a TV device for many video games or camcorders. However, due to the wide
variety of signals generated by these devices and subsequent hook-up variations required, they have not all
been included in the suggested connection diagrams. You'll need to consult each component's Owner's Manual
for additional information.

Left side of the LCD TV
TV GAME

AV1 VIDEO/AUDIO (L/R) IN

_To

To Audio/
Video OUT

I V_o_l
vmEIEo
,I,uD,o
II
AUDIOII
VIDEOL R _1

CUM_UN_

Audio/Videocord
(not supplied)

Audio/Video

cord (not supplied)

To AV2 VIDEO/AUDIO

(L!R) IN

Using an AV Amplifier with built-in digital surround
If you are using an Amplifier with built-in digital surround sound, you can enjoy various audio systems including
Dolby Digital Surround audio that sounds just like the movie.
Connect an AV amplifier with built-in Dolby Digital decoder, or etc. as shown below.
Left side of the LCD TV
Subwoofer

s F °ii\
Coaxial Digital Audio Output
--

Coaxial digital cable
(not supplied)

Front
Speaker
(Right)

Cente_

To Coaxial Digital Audio Input

iA" "_mp_t
hCbult .O di[_g
ilal_--_
surround decoder as listed above

_--

Surround

Speaker (Left) _

Sp;_)er

NOTE:
• Coaxial digital audio output is active only when receiving digital broadcasting, not when receiving analog
broadcasting.
• Coaxial digital audio output doesn't output the sound of external inputs.

Connections to other equipment
To connect an audio system
This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the
TV's remote control.
To control the audio, turn on the TV and the stereo amplifier, and turn off the-rv's built-in speakers (see "Turning
off the built-in speakers" on page 25).
i
=

Left side of the TV
Amplifier
I

[]

BBBBB

ooo

0 ooo

To Audio (L) Input -'_To
/
Audio cord (not supplied) /

Audio (R) Input

NOTE:
To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set
above 0 (zero).
For example, if the volume of the TV is set to 0, you wilt not be able to hear any sound, even if the volume of the
amplifier is at its highest level.

To connect the LCD TV to a PC (Personal

Computer)

Before you connect this LCD TV to your PC, change the adjustment of your PC's Resolution and Refresh rate

(60 Hz).
Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA
connector PC MONITOR on the back of the LCD TV. Attach the connectors firmly with the screws on the plug. In
case of a Multimedia computer, connect the audio cord to the audio output of your Multimedia computer and to
the AUDIO connector of the PC/HDMI-1 AUDIO IN jack of the LCD TV.
Press INPUT SELECT on the remote control to select PC mode.
Switch on the computer. The LCD TV can operate as the computer monitor.
Left side of the LCD TV
MI

HDMk_ II III

HDMMII II

FC
MONITOR

PC
To PC MONITOR IN

1
To PC/
HDMI-1
AUDIO
IN jack

Monitor
MODE
VGA
VGA
SVGA
XGA
WXGA
WXGA
WXGA

Display modes
Resolution
640x480
720x400
800x600
1024x768
1280x768
1280x720
1360x768

Refresh rate
60Hz
70Hz
60Hz
60Hz
60Hz
60Hz
60Hz

To return to normal mode
Press INPUT SELECT again.
Audio cord (not supplied)

NOTE:
• The on-screen displays will have a different appearance in PC mode than in TV mode.
• If there is no video signal from the PC when the unit is in PC mode, "No signal" will appear on the TV-screen.

Setting the language
You can choose from three different languages
(English, French and Spanish) for the on-screen
displays.
Select the language you prefer first, then
proceed with the other menu options.
To turn on the TV, press POWER.
(POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.)

Press EXIT to return to the normal screen.
CABLE CHART
The chart below is typical of many cable system
channel allocations.
Number
on this TV
Co, responding
...........

Press MENU. The menu screen will appear.
Press • or • to select"Setup",
ENTER.

then press t,- or

Press • or • to select"Language".

1A4

........
AA

54
RR

55
SS

56
TT

57
UU

58
VV

OOO

PPP

QQQ

2K4

2p9

41
EE

42
FF

43
GG

44
HH

45
//

46
JJ

47
KK

48
LL

49
MM

50
NN

51
OO

52
PP

59
WW

A6OA

B_B

62
CCC

63
DDD

j6j_

K70 K

....
RRR

SSS

T7T79
T uBu0U

XXX

8yiy

95
A-5

96
A_

97
A-3

98
A-2

99
A-1

100
100

101
101

102
102

t03
103

104
104

105
105

106
106

t07
107

108
108

109
109

110
110

111
111

112
112

113
113

114
114

115
115

116
116

117
117

118
118

t19
t19

120
120

t21
121

122
122

123
123

t24
124

125
125

126
126

127
127

131

t32

133

134

135

181

t32

133

184

135

EoE4E F65F G6_G

...... WWW
VVV

H6F_H
Z8Z5
z

..................
86
87

53
QQ

7L1L MMM
.......... NNN

128
128

129
129

130
130

NOTE:
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.

Automatic search
NOTE:
• When you press MENU first time after purchase this
LCD TV, above screen will appear automatically.

1
2

Press • or _ to select the desired language:
English, French (Frangais) or Spanish (Espa_ol).
Press EXIT to return to the normal screen.
NOTE:
• If no buttons are pressed for more than about 60
seconds, the MENU screen will return to normal
operation automatically.

Press MENU. The menu screen will appear.
Press • or • to select "Channel", then press _ or
ENTER.
Press • or • to select "Auto Ch Memory", then
press _ or ENTER.
Press • or • to select "Automatic Search", then
press ENTER.

Memorizing channels
This TV is equipped with a channel memory
feature which allows channels to skip up or down
to the next channel set into memory, skipping
over unwanted channels. Before selecting
channels, they must be programmed into the
TV's memory. To use this TV with an antenna, set
the Tuning Band menu option to the Air mode.
When shipped from the factory, this menu option
is in the Cable mode.

The TV will begin memorizing all the channels
available in your area.
• It may take from 15 minutes to 30 minutes to
complete memorizing digital cable channels.
Depending on the reception condition, a BAR
display may not advance for several minutes,
please be patient.
Press EXIT to return to the normal screen.

Air/Cable selection
Press MENU. The menu screen will appear.
Press • or • to select "Channel", then press
or ENTER.
Press • or • to select"Auto Ch Memory", then
press _ or ENTER.
Press • or • to select"Signal

Type".

Press • or _ to select"Air" or "Cable".

NOTE:
• Memorizing channels is best accomplished during
evening "PRIMETIME" hours, as more stations are
broadcasting digital signals. Memorizing channels
can only be accomplished while a station is
broadcasting a digital signal to set that channel into
memory.
• If you are unsure of the digital channels available
in your area, you may visit www.antennaweb.org to
receive a list based on your address or zip code.
Should you require further assistance you may call
our toll-free customer service line at 1-800-289-0980.
• New digital channels may be added to your area
periodically, it is recommended to perform the
"Automatic Search" procedure regularly.

Adding
Channel
If you find a new channel unregistered, you can add
the new channel into the channel memory.
Tune in the new channel.

Press MENU. The menu screen wilt appear.

Press • or • to select "Channel", then press _ or
ENTER.
Press • or • to select"Add/Delete",
or ENTER.

then press

Press EXIT to return to the normal screen.

TV operation
To turn on the TV, press POWER.
(POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.)
Adjust
the volume
level
pressingonVOL
or -.
The volume
level will
be by
indicated
the +
screen
by white bars. As the volume level increases, so
do the number of bars. If the volume decreases,
the number of white bars also decreases.

Press • or • to select"Adding Channel", then
press I_ or ENTER. The new channel will be
added into the channel memory.
Press EXIT to return to the normal screen.
Add/Delete

channel

You can select the channel that you want to skip.
Press MENU.The

menu screen wilt appear.

2
3

Press • or • to select "Channel", then press _ or
ENTER.

4
5

Press • or • to select "Add/Delete", then press
or ENTER.

Press • or • to select the channel that you want
to skip.

Press • or _ to select "Add" or "Delete",
whichever function you want to perform.
Repeat
steps 5 - 6 for other channels you want to
add
or delete.
Press EXIT to return to the normal screen.

3
4

Set the Signal Type option to the appropriate
position (see "Air/Cable selection" on page 17).
Press the Direct Channel Selection (0-9, -)
buttons to select the channel, then press ENTER.
(If you press only channel number, channel
selection wilt be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1-9:
Press 1-9 as needed. Example, to
select channel 2, press 2.
10-99:
Press the 2 digits in order. Example, to
select channel 12, press 1, 2.
100-135: Press the 3 digits in order. Example, to
select channel 120, press 1, 2, 0.
TO SELECT DIGITAL CHANNELS
Press the first 3 digits, then press the - button,
followed by the remaining number.
Example, to select channel 015-001, press 0, 1,
5,-, 1.
• If a channel is selected with only audio content,
"Audio only" will be displayed on the screen.
• If a channel is selected with a weak digital
signal, "Digital channel signal strength is low"
will be displayed on the screen.
If the digital channel has the same analog
channel, you way be able to watch the same
channel with analog.
• If a channel is selected to which you have not
subscribed, "Digital channel is encrypted" will
be displayed on the screen.

VHF/UHF/CABLE
Clear All
All channels are deleted from the channel memory.
Press MENU.The

menu screen wilt appear.

Press • or • to select"Channel",
ENTER.
Press
• or • to select"Add/Delete",
or
ENTER.
Press
• or • to select"Clear
ENTER.

then press t,- or
then press

All", then press _ or

CHANNELS

Air

Cable

VHF
2-13
UHF
14-69

VHF
2-13
STD/H RC/I RC
14-36
37-59
60-85
86-94
95-99
100-135
01

(A) (W)
(AA) (WW)
(AAA) (ZZZ)
(86) (94)
(A-5) (A-1)
(100)(135)
(5A)

NOTE:
• If a channel with no broadcast is selected, the
sound will automatically be muted.
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.

RECALL

To select the video input source
Press INPUT SELECT, then press A/T or
corresponding Number buttons (0-6) to view a
signal from another device connected to your LCD
TV, such as a VCR or DVD player. You can select TV,
Video1, Video2, Component, HDMI1, HDMI2 or PC
depending on which input jacks you used to connect
your devices.

MUTE

OH+IPress and release OH + / -. The channel
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See "Memorizing
channels" on pages 17 and 18.

This button allows you to go back to the last channel
selected by pressing RECALL. Press RECALL again
to return to the last channel you were watching.

Press MUTE to switch off the sound. The -I-V'ssound
will be silenced and "Mute" will briefly appear on
the screen. The sound can be switched back on by
pressing this button again or the VOL + or -.

SLEEP
To set the TV to turn off after a preset amount of
time, press SLEEP on the remote control. The clock
will count up 10 minutes for each press of the SLEEP
button (Off, Oh 10m, Oh 20m ..... 2h 0m). After the
sleep time is programmed, the display will appear
briefly every ten minutes to remind you that the sleep
timer is operating. To confirm the sleep timer setting,
press SLEEP and the remaining time will be displayed for a few seconds. To cancel the sleep timer,
press SLEEP repeatedly until the display turns to Off.

oh lore

DISPLAY
Press DISPLAY to display the current information on
the screen.
When the TV receives a digital signal, the digital
information will appear.

Labeling channels
Channel label appear with the channel number
display each time you turn on the TV, select a
channel, or press DISPLAY.
You can choose any four characters to identify a
channel.

•
•
•
•
•
•

Channel number
Channel label (if preset)
V-Chip rating
Clock
Audio language
Picture size

•
•
•
•
•
•

Station name
Broadcast program name
Signal type
Sleep timer
Program guide
Resolution

When the TV receives a analog signal, the analog
information will appear.

•
•
•
•

Channel number
V-Chip rating
Sleep timer
Picture size

•
•
•
•

Channel label (if preset)
Signal type
Audio information (Stereo or SAP)
Resolution

To create channel labels
Press MENU, then press • or • to select
"Channel" menu, then press _ or ENTER.
Press • or • to select"Ch Label", then
press I_ or ENTER.
The "Ch Label" menu will appear.
Press • or _ to select a channel you want to
label, then press •.

Press • or _- repeatedly until the character you
want appears in the first space.

Press DISPLAY again to clear the call display.
NOTE:
• After 10 seconds, DISPLAY screen wilt return to
normal TV-operation automatically.

The characters rotation as follows:

To register
0"'9

<"_A.--Z
<-_* ,0 @/+=• SPACE
<

a password

<-7

If the character which you desire appears, press
ENTER.
Repeat this step to enter the rest of the
characters.
If you would like a blank space in the label name,
you must choose the empty space from the list of
characters.

Press MENU.The menu screen will appear.
Press • or • to select"Lock", then press _ or
ENTER.
Select and enter your password (4 digits) using
Number buttons (0-9), then press ENTER.

When
finishto inputting
thescreen.
label name, press
EXIT toyou
return
the normal
Repeat steps 1-5 for other channel.You can
assign a label to each channel.
To clear a Oh Label
After step 3 above, press • or • to select "Label
Clear", then press _ or ENTER.
NOTE:
The channel labels will be reset after "Automatic
Search" on page 17.

Labeling video inputs
The Video Label feature allows you to label each
input source for your TV.

">k"appears instead of the number.
Enter the same password again to confirm, then
press ENTER.
The password is now registered.
NOTE:
• If you forget the password, contact Customer
Service at 1-800-289-0980 for assistance.
Your original remote control will be required.
• To avoid forgetting the password, write it down and
keep in a safe place.

To set the V-Chip

Press MENU. The menu screen wilt appear.

Press MENU.
Press • or • to select"Lock"
=,-or ENTER.

Press
• or • to select"Setup",
ENTER.

Use Number buttons (0-9) to enter your
password. Then Lock menu wilt appear.

Press
• or • to select"Video
=,-or ENTER.

then press _ or
Label", then press

Press
label. • or • to select an input which you want to
Press • or _ to select the desired label for that
input source.

menu, then press

Press
• to select"V-Chip",
• or _ •toorselect
"On".

then press

Press • or • to select"V-Chip Set", then press
=,-or ENTER.
The V-Chip Set Menu appears.
Press • or • to select which rating will be used,
then press _ or ENTER. Each rating below will
appear.
TV Rating

VCR
DVD
DTV
SAT
DBL
HD

: Uses the default label name
:Video cassette recorder
: DVD video
: Digital TV set-top box
: Satellite box
: Cable box
: HDMI device (only for HDMI inputs)

Press EXIT to return to the normal screen.

Setting the V-Chip
An age limitation can be set to restrict children
from viewing or hearing violent scenes or
pictures that you may choose to exclude. The
restriction applies to "TV Rating" and "Movie
Rating" if this data is transmitted. You may set
this restriction separately. To use the V-Chip
function, you must register a password.

You can set the rating using age level and genre.
Age:
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA

:All children
:7 years old and above
: General audience
: Parental guidance
: 14 years old and above
: 17 years old and above

Genre:
ALL
D
L
S
V
FV

:All
: Dialogue
: Language
: Sex
:Violence
: Fantasy Violence

Movie Rating

4
5
G
PG
PG-13
R
NC-17
X

All ages
Parental guidance
Parental guidance less than 13 years old
Under 17 years old parental guidance
suggested
17 years old and above
Adult only

Press A/T/
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.2
Linearized : No
Page Count : 32
Page Layout : SinglePage
Page Mode : UseNone
Producer : Goby Monitor Application version 4, 0, 0, 13
Create Date : Thu Nov 27 04:16:29 2008
Author :
Title :
Subject :

EXIF Metadata provided by EXIF.tools

Sansui HDLCD2600A User Manual LCD TELEVISION Manuals And Guides L0811658

SANSUI LCD Television Manual L0811658 SANSUI LCD Television Owner's Manual, SANSUI LCD Television installation guides

TESCO SP-4291 L0811658

Navigation menu

Versions of this User Manual:

Views

Navigation