Sanyo Electric Co CDR032 DVD-WRITER User Manual

Sanyo Electric Co Ltd DVD-WRITER Users Manual

Users Manual

Page 2 Document No. Document Name SANYO Electric Co., Ltd. Revision History (1/1) 1. Revision History Revision No. Manager Change Description Check ApprovalFirst Edition Newly issued
Page 3 Document No. Document Name SANYO Electric Co., Ltd. Included Document List (1/1) 2. Included Document List Document Name Document No. Page No.General Description 1/3 ~ 3/3 4 Dimensions, External View and Names and Functions of Each Part 1/2 ~ 2/2 7 Terminal Description 1/3 ~ 3/3 9 Environmental Conditions 1/1 12 Reliability 1/3 ~ 3/3 13 Lot No. Reliability Description 1/1 16 Safety Standards 1/1 17 Electrical Characteristics 1/3 ~ 3/3 18 Function Description 1/3 ~ 3/3 21 Handling Manual 1/1 24 Notes for Handling 1/5 ~ 5/5 25
Page 4 Document No. Document Name SANYO Electric Co., Ltd. General Description (1/3) General Description (1) Model Name: CRD-BPDV3 DVD-R/RW: drive with MAX ×12 speed reading, (×8) speed writing, ×4 speed rewriting. DVD+R/RW: drive with MAX ×12 speed reading, ×8 speed writing, ×4 speed rewriting. CD-R drive with MAX ×48 speed reading, ×48 speed writing, and ×24 rewriting) ““““The DVD-R/RW or DVD+R/RW feature will be selectable by the firmware.”””” (2) External View External View (3) General Specifications 1) Characteristics * Half-height and built-in type * Conforms to Orange Book Part 2, 3 & DVD±R/RW for general specifications. * Equipped with the newly developed automatic strategy LSI with the data reliability enhanced. * DVD-R/RW drive with MAX ×12 speed reading(CAV), (×8) speed writing(PCAV),×4 speed rewriting(CLV) DVD+R/RW drive with MAX ×12 speed reading(CAV),×8 speed writing(PCAV), ×4speed rewriting(CLV). CD-R drive with MAX ×48 speed reading, ×48 speed writing(ZCLV), and ×24 rewriting(CLV) * ATAPI is employed to enable high speed data transmission. * Automatic loading mechanism * Emergency disc ejecting function * Data verifying function * Media condition check function * CD-DA read function * Vertical operation feasible * BURN-Proof Technology implemented “BURN-Proof” stands for Proof against Buffer Under Run error, not for proof against burning. * HD-BURN: a high-density writing technology * Safe-BP: detects recording error due to irregular mechanical characteristics. * FlexSS-BP: automatically selects the optimum recording speed for each disc. * MRW function（CD and DVD）will support.
Page 5 Document No. Document Name SANYO Electric Co., Ltd. General Description (2/3) (4) Main Specifications Items Specifications Dimensions 148 (W) × 194.2 (D) × 42.3 (H) mm Mass 1020 g Recording Form Orange-book part 2, 3 Fixed packet Disc-at-once Variable packet Track-at-once DVD-R for general 2.0 Disc at Once RecordingIncremental Recording Front Panel Eject key, Emergency eject pinhole, LED (busy and write) Headphone jack, Volume Eject Automatic loading Power Supply DC 5 × (1 ± 5 %) V DC 12 × (1 ± 10 %) V (5) Operational environment for the “write/rewrite” application software Items Specifications Host Machine IBM compatible PC (Celeron433MHz or more) (Note 1) OS MS-Windows 98SE/ME/2000/NT4.0/XP (Note 2) Memory MS-Windows 98SE/ME/NT: 128 MB or more. MS-Windows2000/WindowsXP: 128 MB required. 256 MB recommended. Hard disc Empty Storage Capacity: 5GB or more (20GB or more recommended) Average seek time: 20 ms or less Transmission rate: 2 MB/s or more Do not use the HDD which calibrate thermal during operation. CD-R (×4 ~ ×48) : MITSUI CHEMICAL , HITACHI MAXELL, RITEK, ACER, CMC (T.B.D) CD-RW (×4 ,×10, ×12, ×16,×24 ) :MITSUBISHI CHEMICAL, RICOH (T.B.D) (Note 3)Recommended Media DVD-R(×2, ×4, ×8):MITUBISHI CHEMICAL,HITACHI MAXELL, PIONEER VIDEO,TAIYO YUDEN,TDK DVD-RW(×2, ×4):PIONEER VIDEO,MITUBISHI CHEMICAL ,PRINCO DVD+R (×2.4, ×4, ×8):RICOH,MITUBISHI CHEMICAL,RITEK DVD+RW(×2.4, ×4):RICOH,MITUBISHI CHEMICAL,RITEK (T.B.D) (Note 1) If any problem occurs, negotiation is required to settle the matter. (Note 2) Windows NT4.0 doesn’t have ATAPI-DMA-Driver in the standard. Therefore, this Drive and IDE-HDD function with PIO-Mode. (Note 3) We intend to add the proper media one by one in the near future.
Page 6 Document No. Document Name SANYO Electric Co., Ltd. General Description (3/3) (6) Scope This specification is applied to the CD-R/RW/DVD-R/RW,DVD+R/RW drive “CRD-BPDV3” which is designed by SANYO Electric Co., Ltd. (7) Contents 1) Model No. CRD-BPDV3 2) Performance Write function onto CD-R/RW/DVD-R/RW/DVD+R/RW disc in combination with the write application software and CD-ROM/DVD-ROM read function, in combination with the CD-ROM/DVD-ROM application software. 3) Applications Write onto and read of the CD-R/RW/DVD-R/RW/DVD+R/RW disc. Read of CD-ROM/DVD-ROM disc. 4) Dimensions Refer to the item “Dimensions and Dimensional Drawing”. 5) Notes for handling Refer to the Manual and Notes for Handling. 6) Others a. The specifications of this product are the same as in the delivery specifications. If any fault or malfunction of the product occurs when it is used under any conditions except for our guaranteed conditions, our company has no responsibility for the claim. b. The specifications of this product are subject to change to enhance the performance. c. The change of notice is issued when the specification is changed only. d. If any doubt occurs regarding the contents of the specifications, negotiation is required to settle the matter.
Page 7 Document No. Document Name SANYO Electric Co., Ltd. Dimensions, External View and Names and Functions of Each Part (1/2) 1. Dimensions and External View (1) External View Refer to the “General Description”. (2) Dimensions and Dimensional Drawing Refer to the attached document “Dimensions and Dimensional Drawing”. (3) Names and Functions of Each Part on the Front Panel Front Panel 1. Headphone Terminal : The headphone with a stereo mini plug is connected through this terminal. 2. Headphone Volume : The volume of the headphone connected to the headphone terminal is adjusted using this volume dial. When the volume dial is turned right, the volume becomes louder. 3. BUSY indicator : Command executing. ON Reading disc, accessing condition and TOC reading condition. OFF Pause or Stop condition 4. WRITE indicator : This is ON when the data is written onto the disc. 5. EJECT key : The disc is ejected, using this key. This key is available even when the tray is moving. When the PRV command is transmitted from HOST or during writing, this key is not available. 6. Emergency eject pinhole : If the disc is not ejected when the key is pressed, because of power failure or run away of the software, this pinhole is used to take out the disc. 7. Disc tray : The disc is placed on this tray. 6 7 5 1 243
Page 8 Document No. Document Name SANYO Electric Co., Ltd. Dimensions, External View and Names and Functions of Each Part (2/2) (4) Names and Functions of Each Part on the Rear Panel Rear Panel 1. ANALOG AUDIO Connector : The audio analog signal output connector. 2. CS/SL/MA Pins : By covering the jumper block, these pins are used to set the CD-R drive to either a Master or Slave mode to work with the hard disk drive inside the personal computer. Default is Master. 3. IDE Connector : Using a 40-pin connector, the ATAPI terminal of the host computer is connected to this connector. 4. DC Connector : This is the power supply terminal. 5. FACTORY USE ONLY Pins : These pins are used only for the test in the factory. Don’t cover the jumper block on them. 6. DIGITAL AUDIO Connector : The audio digital signal output connector. 7. UDMA Pins : UDMA mode is enabled by covering the jumper block on the 2 pins of the UDMA jumper terminals. Default is ON. (Note 1) In case of using some personal computes, UDMA mode need to be disable. 1 234 6 5 7
Page 9 Document No. Document Name SANYO Electric Co., Ltd. Terminal Description (1/3) 1. AUDIO Terminals The audio signal is output through these terminals. These terminals are used when the sound board applicable to these terminals, is attached to the personal computer. 2. Jumper Terminals (CS/SL/MA) SLSLSLSL Jumper Terminals: To set to Slave mode, cover the jumper block on the 2 pins of the SL jumper terminals. If the IDE controller of the personal computer supports two devices, set the CD-R drive to Slave mode. The hard disk drive inside the personal computer is set to Master mode. MAMAMAMA Jumper Terminals: To set to Master mode, cover the jumper block on the 2 pins of the MA jumper terminals. If the IDE controller of the personal computer supports up to four devices, set the CD-R drive to either a Primary Slave, a Secondary Master or a Secondary Slave mode. Primary or Secondary is set up by the IDE controller, while Master or Slave mode is set up by covering the jumper block on the rear of the CD-R drive. The hard disk drive inside the personal computer is set to Primary Master mode. CSCSCSCS Jumper Terminals: If the personal computer is supporting CSEL (Cable Select) signal, cover the jumper block on the 2 pins of the CS jumper terminals and remain Slave and Master open. An exclusive interface cable is necessary. R-ch GND L-ch GND Slave Master Use CSEL Jumper block Jumperblock
Page 10 Document No. Document Name SANYO Electric Co., Ltd. Terminal Description (2/3) 3. IDE Connector Terminals (ATAPI CONNECTOR) The IDE terminal of the host computer is connected through these terminals. Use the 40-pin IDE cable. The pin marked “1” means pin No. 1. Connect the IDE cable of the color-coding (normally red) on one edge to pin No. 1. PIN NO. SIGNAL NAME PIN NO. SIGNAL NAME 2 Ground 1 RESET- 4 DD8 3 DD7 6 DD9 5 DD6 8 DD10 7 DD5 10 DD11 9 DD4 12 DD12 11 DD3 14 DD13 13 DD2 16 DD14 15 DD1 18 DD15 17 DD0 20 (keypin) 19 Ground 22 Ground 21 DMARQ 24 Ground 23 DIOW-:STOP 26 Ground 25 DIOR-:HDMARDY- :HSTROBE 28 CSEL 27 IORDY:DDMARDY- :DSTROBE 30 Ground 29 DMACK- 32 reserved 31 INTRQ 34 PDIAG- 33 DA1 36 DA2 35 DA0 38 CS1- 37 CS0- 40 Ground 39 DASP- 39401 2
Page 11 Document No. Document Name SANYO Electric Co., Ltd. Terminal Description (3/3) 4. DC Connector Terminals (DC INPUT) The DC power supply cable is connected through these terminals. 5V 12V GND
Page 12 Document No. Document Name SANYO Electric Co., Ltd. Environmental Conditions (1/1) Environmental Conditions Items Environmental Conditions Temperature Operation : 5 °C < to < 40 °C Storage : −30 °C < tNO < 60 °C Humidity Operation : (20 to 80) % (non-condensing) Storage : 90 % (40 °C, 48 h) Mean-Time-Between-Failure (MTBF) 30000 POH DUTY 20 % (read operation) (Note 1) Life Tray loading : 20000 cycles Traverse mechanism : 1000000 seek Vibration Operation: Read 0.98 m/s2 (0.1 G) [(10 to 500) Hz] Random Vibration Without operation (transportation): 800 cpm (13.3 Hz), 3 mm (1.06 G), Up/Down 20 min. Impact Drop Impact: 490 m/s2 (50 G), 3 directions, 6 ms (Note 1) POH : Power On Hour (live current time) DUTY : Actual operation time
Page 13 Document No. Document Name SANYO Electric Co., Ltd. Reliability (1/3) 1. Estimate Conditions 1) Standard test position For the standard test position, the + side of the Z axis shall be in the upper direction, provided that the Z axis shall be the outgoing beam and the direction of the outgoing beam shall be + side. 2) Standard Estimate Environments Temperature : (22 ± 2) °C Humidity : (50 ± 5) % RH However, when no doubt occurs regarding the judgment, the test may be performed under the following conditions. Temperature : (15 to 30) °C Humidity : (45 to 85) % RH 3) Disc to be estimated Test Disc made by ALMEDIO Inc. ROM DISK, DA DISK, CD-R DISK (RICOH), CD-RW (RICOH, MITSUBISHI CHEMICAL) DVD-R/+R(RICOH,MITSUBISHI CHEMICAL) DVD-RW/+RW(RICOH,MITSUBISHI CHEMICAL) However, when no doubt occurs regarding the judgment, TCD-784 made by ALMEDIO Inc. may be used. 4) Power Supply Voltage Power supply : DC 5 × (1 ± 5 %) V Power supply : DC 12 × (1 ± 10 %) V 2. Reliability The results should conform to the criteria of each item after the test has been performed under the following conditions. There shall be no crack, deformation or distortion from the external view of the product after the test. Unless otherwise specified, the measurement conditions of this test for each item shall be subject to the above estimate conditions. However, the temperature in this test shall be specified to the surrounding temperature of the drive unit, rather than the surrounding temperature of the set unit where this product is built-in.
Page 14 Document No. Document Name SANYO Electric Co., Ltd. Reliability (2/3) Test items Test conditions Criteria 1. Operating temperature test Operation under low temperature: +5 °C Operation under high temperature: +40 °C Leave the product for 4 hours without operation in the environmental temperatures, as above. Turn on the power and leave the product for 10 minutes. Immediately after that, check the performance under the same environmental temperatures as above. However, there should be no dew condensation. The performance should conform to the standards described in the Reliability Estimation Standard Table. 2. Practical operation temperature test Operation under low temperature: +5 °C Operation under high temperature: +40 °C Leave the product for 4 hours without operation in the environmental temperatures, as above. Turn on the power of the product and leave the product for 10 minutes. Immediately after that, check the performance under the same environmental temperatures as above. However, there should be no dew condensation. There should be no errors in the practical operation. When this product is built in the set unit, make sure that the temperature does not exceed the range described on the left. 3. Storage test under low temperature. Temperature: (−30 ± 2) °C Leave the product for 24 hours without operation in the above environmental temperature range, and then leave it at normal temperature for 24 hours. After that, measure the characteristic change. However, there should be no dew condensation. The characteristics should conform to the standards described in the Reliability Estimation Standards Table. 4. Storage test under high temperature Temperature: (60 ± 2) °C Leave the product for 24 hours without operation in the above environmental temperature range, and then leave it at normal temperature for 24 hours. After that, measure the characteristic change. However, there should be no dew condensation. The characteristics should conform to the standards described in the Reliability Estimation Standards Table. 5. Storage under high temperature and high humidity Temperature and humidity: (40 ± 2) °C, (90 ± 2) % RH Leave the product for 24 hours without operation in the above environmental temperature range, and then leave it at normal temperature for 24 hours. After that, measure the characteristic change. However, there should be no dew condensation. The characteristics should conform to the standards described in the Reliability Estimation Standards Table. 6. Unit Vibration (without operation) Amplitude:800 cpm (13.3 Hz) 3 mm (1.06 G) The above amplitude is applied to the product for 20 minutes for Up/Down direction. The characteristics should conform to the standards described in the ReliabilityEstimation Standards Table. 7. Unit Impact (without operation) Impact: 490 m/s2 (50 G), 3 directions Impact time: 6 ms Measure the performance after applying the above impact for each direction. The characteristics should conform to the standards described in the Reliability Estimation Standards Table. 8. Pick-up Slide Operation Random Seek After 1000000 times operation, the performance is checked. There should be no errors in the practical operation. 9. Jamming When the product is built in the set unit, the level of electromagnetic wave which is emitted from the unit shall conform to the local radio wave standards. (When any problems occurs, the negotiation is required to support the counter measures).
Page 15 Document No. Document Name SANYO Electric Co., Ltd. Reliability (3/3) The following table shows the reliability standards for the main parts (units) which are used in this product. Test items Test conditions Criteria 10. Laser diode life Check the recorded power after 1000 hours of operation at 60 °C. (except for breakage caused by static electricity) The error rate should be 1 % or less. 11. Spindle motor life Measure the current in the motor after 1000 hours operation. The initial value should be +35 % or less. 12. Feeder motor life After the pick-up slide operation as described in item 8, measure the consumption current in the motor. The values should be conform to the pull-out torque 1500pps 9.8×10-4 N-m (10grf-cm) or more. 3. Reliability Standards The reliability standards are as follows. 1).CD 2).DVD Items Before Test Change in Values after Test Remarks 1/3 stroke mean access time ×48 CAV speed 0.27 s or less 0.35 s or less Mean value measured after reciprocating operation for (0 to 20) min. (one way value) Items Before Test Change in Values after Test Remarks 1/3 stroke mean access time ×12 CAV speed 0.27 s or less 0.35 s or less Mean value measured after reciprocating operation for (0 to 20) min. (one way value)
Page 16 Document No. Document Name SANYO Electric Co., Ltd. Lot No. Reliability Description (1/1) Lot No. Description [Serial No. Indication] 1 2 3 4 5 6 7 8 A B C D D D D D A. Factory: Korea Tokyo Electronics: 6, Sanyo Media Tech: 3, SSHQ: 8 B. Year of manufactured: (1996: 6, 1997: 7, 1998: 8, 1999: 9, 2000: 0, 2001: 1, 2002: 2, 2003: 3, 2004: 4, 2005: 5) C. Month of manufactured: Form Jan. to Sep.: 1 ~ 9 & Form Oct. to Dec.:X ~Z (Jan: 1, Feb: 2, Mar: 3, Apr: 4, May: 5, Jun: 6, Jul: 7, Aug:8, Sep: 9, Oct: X, Nov: Y, Dec: Z) D. Manufacturing Serial No.: Start from 00001. (5 digits) When the number reach to 99999, the next is 00000, then 00001 again.
Page 17 Document No. Document Name SANYO Electric Co., Ltd. Safety Standards (1/1) Safety Standards (1) UL (UL1950 / FDA1040) (2) CUL (UL1950) (3) Label
Page 20 Document No. Document Name SANYO Electric Co., Ltd. Electrical Characteristics (3/3) Application Discs Items Specifications CD-ROM mode 1 CD-ROMXA (Video CD) mode 2 form 1, mode 2 form 2 CD-DA Applicable Photo CD Single session, multi-session CD-I, CD-G, CD-TEXT Applicable CD Extra 2 Session First Session : CD-DA Second Session : Data Disc dia. 12 cm, 8 cm Storage capacity 12 cm : 656 MB (mode 1) 748 MB (mode 2) 8 cm : 180 MB Disc thickness 1.2 mm Track pitch 1.6 µm Items Specifications DVD-R,-RW/DVD-ROM DVD-ROM,DVD-VIDEO DVD+R,+RW/DVD-ROM DVD-ROM,DVD-VIDEO Disc dia. 12 cm Storage capacity 12 cm:4.7GB Disc thickness 1.2 mm Track pitch 0.74 µm Interface Items Specifications Interface ATAPI Transfer Rate U-DMA 33 MB/s Connector Item Specifications I/O terminal (rear panel) Power connector (+5 V, +12 V 4 P) ATAPI terminal (40 P) Audio out (4 P), (2 P)
Page 21 Document No. Document Name SANYO Electric Co., Ltd. Function Description (1/3) 1. External View/Mechanism (1) Tray type disc loading system The disc is loaded on the TRAY. (2) LED Indicator BUSY : ON — Command executing conditions OFF — Pausing and stop conditions WRITE : ON — Recording condition OFF — Others (3) EJECT key The disc is taken out using this key. This key is available even when the tray is moving. However, this key is not available under the recording condition or when the PRV command is transmitted from the HOST. (4) 8 cm/12 cm disc applicable. The read of 8 cm and 12 cm pit discs and the write of 12 cm pit discs of the CD-R disc are available. 2. Data read processing (1) Read speed The standard, CD Max ×24/DVD Max ×12 are applicable. Arbitrary speed can be set using the ATAPI command. (2) Read data mode (Note 1-1) CD DVD MODE 1 2048Byte only MODE 2 / Form 1 MODE 2 / Form 2 CD-DA ISRC Media catalogue No. Sub-codeQ R-W (3) Audio playback TNO playback (MSF search) PAUSE function (Note 1-1) Audio playback becomes possible by using the host application. (as per ATAPI command specifications)
Page 22 Document No. Document Name SANYO Electric Co., Ltd. Function Description (2/3) 3. Data write processing (1) Write speed i. DVD-R ×2, ×4 (CLV), (×8)(PCAV) DVD+R ×2.4, ×4 (CLV),×8(PCAV) ii. DVD-RW ×2, ×4(CLV) DVD+RW ×2.4, ×4 (CLV) iii. CD-R ×4, ×8, ×12, ×16,(CLV) ×16 ~ ×48 (ZCLV) write speed are applicable. ( mastering write) iv. CD-RW ×4, ×10, ×12 (CLV), ×24(CAV) write speed are applicable. v. HD-BURN x6,x12x,x18,x24 ( on a conversion to CD speed) Arbitrary speed can be set using the ATAPI command. (2) Write system CD-R/RW DVD-RW DVD-RW DVD+R DVD+RW Track-at-once Disc-at-once Disc-at-once Incremental write Random over write Disc-at-once Incremental write Incremental write Packet write(variable length/fixed length) Restricted over write (3) Write data mode CD-R/RW DVD±R/RW MODE 1 CD-DA (Note 2-2) 2048Byte only MODE 2 ISRC MODE 2 / Form 1 Media catalogue No. MODE 2 / Form 2 CD-TEXT MODE 2 / Combination of Form1 and Form 2 (Note 2-1) (4) Optimum write function The strategy and write laser power are set automatically according to the characteristics of the disc. This is performed when the disc is replaced or the CLV speed is changed. In addition, the write condition is checked during writing the data, and the running OPC function which sets the optimum laser power, is performed. (5) BURN-Proof BURN-Proof is a proprietary technology, which helps the users to protect from Buffer Under Run Error. (Note 2-1) This is applicable only within the approved range of the CD-ROM and CD-ROM XA. (Note 2-2) Host computer makes and transfers the RAW data which includes pre-gap in the case of the disc-at-once writing. At this time, the track management information needs to provide instructions to transfer the start and end address of the actual audio data portion.
Page 23 Document No. Document Name SANYO Electric Co., Ltd. Function Description (3/3) 4. Servo/access (1) Servo Automatic Adjustment When the disc is loaded, the focus, tracking offset and servo gain are adjusted automatically. (2) Sled Control using the Stepping Motor Driving The mechanisms and circuits related to the sled are simplified. The micro step operation is controlled using the micro computer when the access-time-specific trapezoidal driving occurs and the read/write operation is performed. (3) High speed access using the learning function The number of tracks calculated from the CLV speed and pick-up position are corrected so that the disc program area is kept at the access time accompanied with the travel of the sled. Then, the corrected number of tracks is stored and the final number of tracks on the disc are calculated in order to reduce the number of seeks． 5. Other Functions (1) Multi-volume applicable To switch the sessions, the SESSION SELECTOR is used. (2) Disc identification codes The discs produced by each manufacturer are identified using the disc identification codes prepared by the Orange Society for the Research. This is referred to when the laser power and strategy are decided, when the writing operation is performed. (3) Device type Device type is 05 (CD-ROM) only. 6. CRD-BPDV3 Interface The host computer interface of the CRD-BPDV3 conforms to the ATAPI. 7. BURN-Proof In some case of disc condition, an error may happen by the failer of BURN-Proof function because it controls previous recorded data and new recording data by the advanced signal management system. In addition to the stated above, a BURN-Proof function also does not work correctly due to the unexpected accident like a power cut and a malfunction of PC and so forth. 8. SHOCK-BP Please refer to the latest information on the web: www.burn-proof.com. 9. Safe-BP Please refer to the latest information on the web: www.burn-proof.com. 10. HD-BURN Please refer to the latest information on the web: www.burn-proof.com.
Page 24 Document No. Document Name SANYO Electric Co., Ltd. Handling Manual (1/1) (1) How to use Before using this product, make sure that the device driver for the Combo driver is installed in the personal computer. 1) How to insert the disc. i. Turn on the power of the main machine where the product is attached. ii. Press the eject key to open the disc tray. iii. Place the disc on the tray so that the printed side is upside. iv. Press the eject key to close the disc tray. v. Read the disc. The read indicator goes on-and-off during the TOC read operation. Then the indicator goes on. Write the data onto the disc. The write indicator goes on while the data is written. 2) How to take out the disc. i. Make sure that each indicator is OFF. ii. Press the eject key to open the disc tray. iii. Take out the disc. iv. Press the eject key to close the disc tray. 3) How to take out the disc in an emergency. When the disc can't be ejected because of power failure or run-away of the software, take the following measures to force the take out of the disc. i. Prepare a steel paper clip. Extend the paper clip. ii. Insert the end of the paper clip into the emergency eject hole and press it strongly to eject the disc tray. iii. Pull the disc tray toward you and take out the disc. Push back the disc tray. (2) Product ID, Vender ID Product ID: CRD-BPDV3, Vender ID: GENERIC
Page 25 Document No. Document Name SANYO Electric Co., Ltd. Notes for Handling (1/5) 1. Don't look at the laser beam. Don't look at the laser beam source. If the laser beam hits your eyes, it might cause damage to your eyes. 2. Don't use deformed or cracked CDs and DVDs. Don't use cracked, deformed CDs and DVDs or repaired CDs and DVDs with adhesives. As the disc turns with high speed within the product, broken pieces might scatter and hurt you. 3. Don't touch the inside components of this product. Don't disassemble or modify this product. It might cause the breakdown of this product. 4. Don't touch the connector parts. If you touch the connector parts of this product, it might cause a contact fault or breakdown because of the oil from your hands or static electricity. Also, don't touch the connector part on the personal computer when this product is connected or disconnected. 5. Don't connect and disconnect this product excessively. When this product is connected and disconnected repeatedly, the connector part becomes heavily loaded and this might cause the breakdown of this product. Don't connect and disconnect this product excessively, except for necessary cases. 6. How to prevent the breakdown (1) Don't impact or vibrate this product. (2) Keep the product where no fluid or alien substances can enter into this product. (3) Don't use this product on an incline. (4) Don't move this product with the disc inside. 7. Installation Place Avoid the following places for using this product. (1) Places of high temperature or greate changes in temperature. (2) Places where sunlight can hit the product directly. (3) Places with strong vibrations. (4) Places with uneven surfaces.
Page 26 Document No. Document Name SANYO Electric Co., Ltd. Notes for Handling (2/5) 8. Maintenance (1) The dirt on this product should be cleaned off lightly with a soft cloth with some water or diluted neutral detergent. (2) Make sure not to use volatile chemicals such as benzine and thinner, because they might cause deformation and color change of the product. 9. Notes for the Handling of the Disc. (1) When you carry the disc, don’t touch the side where no letters are printed. (2) Don't write letters on the disc or attach paper or a seal. (3) Dust or finger prints on the side without any printing should be cleaned off by a soft cloth. (4) When the disc is cleaned, always clean from the center to the outer rim. (5) Don't use benzine, thinner, cleaner for analog LP or a static electricity preventing agent, because these might cause damage to the disc. (6) Keep the discs in the disc case. Don't put the disc in a place where sunlight can hit directly or the temperature increases. 10. It is prohibited from copying, selling and transfering datas and programs that are protected by the copyright to the authorities without permission. However, personal use of the sound and images that are recorded with this product is permitted. 11. Application The following applications may be supported by this product, in future. (Therefore, we are not responsible for any defects or damages using other applications. Also, some version no. of above Applications may not recognize the drive. Please contact to the Application maker.) Software DVD Player: WinDVD (InterVideo Inc.), PowerDVD Software writing Storage: NERO Version5 (AHEAD)， B’sRecorderGold(BHA) , Software DVD Video Recording: DVD it!,(Sonic Solutions), NEO DVD(Medio Streams) 12. Drive Mount This drive has holes for heat radiation at top cabinet and side cabinet. Please do not fill these ventilation holes. Please avoid any components from these ventilation holes over 5mm in order to keep circulation. 13.Recommend to use the JIS standard disc what is described the CD Logo XXX marking on the surface of disc label side. We do not guarantee the play-back function if the out of CD standard disc is inserted. Even if it can be played, the sound qualities are not guaranteed.
Page 27 Document No. Document Name SANYO Electric Co., Ltd. Notes for Handling (3/5) Dimensions The following items should be considered when enclosure chassis for this drive is designed. 1. Over 5 mm space should needed between top of drive and enclosure chassis. 2. Don’t press the production label even if there are any reasons.
Page 28 Document No. Document Name SANYO Electric Co., Ltd. Notes for Handling (4/5) Package
Page 29 Document No. Document Name SANYO Electric Co., Ltd. Notes for Handling (5/5) Package Configuration GROSS WEIGHT 12 kg 300 unit 1 pallet: 6 box × 5 stack (30 box) Pallets are to be banded and stretch-wrapped. Corner strips are attached.

Navigation menu