Sanyo Electric Co PBS-CS37 The Radio Cell Station for PHS WLL System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	365184
Application ID	GxmL/pft8fYVSo6RpGqRXg==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.63kB (357813 bits)
Date Submitted	2003-10-15 00:00:00
Date Available	2003-10-15 00:00:00
Creation Date	2003-09-29 15:53:52
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2003-09-29 15:53:52
Document Title	untitled

SANYO
PHS Cell Station
- User’s Manual -
Sep 12, 2002
Table of Contents
Table of contents ............................................................................................................................. 1
Installation conditions ................................................................................................................. 2,3
Fixing antenna for PBS-CS37 ........................................................................................................ 4
Condition of the antenna cable (PBS-CS37) ................................................................................ 5
Terminal block appearance ............................................................................................................ 6
Notes at the time of lid opening and closing ................................................................................. 7
Connection of the power cable .................................................................................................... 8,9
Connection of the line cable .................................................................................................... 11,12
Concerning the installation of cable ............................................................................................ 13
Warning ......................................................................................................................................... 14
Appendix (1), (2) ...................................................................................................................... 15,16
Installation conditions
] Place
\ CS shall be installed in the place where the public can not easily access.
\ Installation place shall have the structure which can support the weight of CS
and its fixing facilities.
\ Installation place shall be flat with no inclination.
\ If CS is installed in the place where it may drop down, it shall be provided
with protective measure against the drop.
\ There shall be no object around 2m of CS.
\ For the maintenance use, there shall be the space in about 500mm around the
stand.
\ CS shall be installed in the direction that the logo plate appears upwards. CS
can be placed in vertical direction with arranging the fixing metal.
Installation conditions
] Antenna
\ With fixing antennas, there shall be enough viewing angle from CS. (Target
angle: vertical: 30 degree or more, horizontal: 330 degree or more)
] ISDN Line
\ Interconnection box for ISDN line shall be available near the CS.
\ ISDN line length from the exchange to CS and its quality shall comply with
the technical standard (ANSI T1.601-1992).
] Power supply
\ AC120V shall be available with easy wiring connection work.
Fixing antenna
for PBS-CS37
PBS-CS37
Breaker
MDF
AC120V
To ISDN Line
Connection of the antenna cable
(PBS-CS37)
Case of Clockwise
] Numbering arrangement
\ Numbering arrangement of 1 - 4 shall be made
clockwise or counterclockwise.
Upper side
antenna
] Tightening torque of the antenna cable:
7 - 12 Kgf-cm.
] Wind the self-bonding tape between the
Case of Counterclockwise
antenna connector and the end of cable.
Upper side
antenna
Terminal block appearance(PBS-CS37)
] Terminal block of the power supply and line’s connections are shown below
1: Status indications LED Label
2: Reset Switch
3: Maintenance terminal connector
4: Status indications LED
5,10: Line check terminal connector
6,9: Line terminal connector
7,8: Line Status LED
11: Power supply Terminal(N)
12: GND Terminal(FG)
13: Power supply Terminal(L)
14: Earth clamp for Power cable
15: Cable gland for power cable
16: Cable gland for Line cable
17: Earth clamp for Line cable
18: GPS indications label for GPS model
Notes at the time of
lid opening and closing
] Opening
After loosening all lid’s fixation screws completely, pull
upper part and central screw of the lid, and slide. (Photo1)
Confirm that all screws are free completely and two pins of
the lid is at the right edge of two metal fittings ,therefore
rotate the lid while pulling in the direction”an arrow” like
below . (Photo2)
Closing
Tightening torque of Cap screw: 10 - 15 Kgf-cm
Tighten with M4 hexagon Socket Cap screws. (Cap screw).
Tighten 6 screws equally and well balanced, after confirming
that the waterproof packing is nonexistent between the lid
and the CS.
[Caution1] If the clamp face or waterproof packing is scarred
by screw’s cusp, the waterproof performance may not be
obtained.
[Caution 2] Photos of PBS-CS47 are used for explanations in
this User’s Manual.
(Photo1)
(Photo2)
Connection of the power cable (1)
1) Reeve the cable from the cable gland nut
into the lid.
Covering
end
Covering
Copper
shield
2) Pull the cable out to enough length that
the tip of the cable can be processed.
3) Peel the covering of the cable. (Photo 3)
4) Peeling off core line.
5) Loosen the copper shield and wind it
onto the core wire’s tip 4 turns or more.
*The cable color is generally used in Japan, and it
used in U.S.A. shall comply with the local
specifications.
70 - 90mm
interposition material:
Cut it at
the covering’ root.
(Photo3)
15mm
60 - 80mm
8 - 9mm
Copper shield
(figure)
Connection of the power cable (2)
6) Feazings processing of the core line.
Push the upper part of the connector with a
finger, and insert a core wire. (figure)
L (Loading), N (Neutral), FG (Frame Ground).
7) Combine the copper shield to the position
“FIX” of Photo 5. And tighten the cable
gland firmly.
[Caution]When the fixation of the terminal
block’s lid is imperfect, it is feared that this
CS gives hindrance to other electric devices.
8) Form core wires that are inserted into the
power supply terminal.
9) The tightening of the dome nut must be
done by hand without fail and tighten it
strongly.
10) Wind the self-bonding tape between the
surface of dome nut and the end of cable.
(figure)
N:White
FG:Red
L:Black
Formin
Fix
(photo5)
Connection of the Line cable (1)
1) Reeve the cable from the dome nut into
the lid.
2) Pull the line cable out to enough length
that the tip of the cable can be
processed.
3) Peeling of the line cable covering.
(Photo 6)
Peel off the covering of the line cable. The
length of the line cable is 100 - 120 mm.
(Photo 6)
Drain wire
Shield tape
Covering
100 - 120mm
(photo6)
Process the end of the line wire, which are
not used, with the suiting tape.
4) Loosen the shield and wind it on the
heart line of covering 4 turns or more.
(Photo 7)
Loosen these four pair lines, plug in the
designated touching sockets.
Wind the aluminum shield, and
furthermore wind drain wire here too.
(photo7)
10
Connection of the Line cable (2)
5) Loosen these four pair lines, plug in the
designated touching sockets.
Pair lines
6) Combine the copper shield to the
position where is located in the arrow
of Photo 8 below. And tighten the
cable gland firmly.
Touching socket
Touching
Before touching
After touching
(Figure)
screw
7) Plug four touching sockets to
the connector on the PWB in the
terminal block. (Photo8)
nd
rou
la m
fo
in e
r th
LA
LB
LC
LC
(photo8)
11
Connection of the Line cable (3)
8) Form core wires that are inserted into the line
connector.
Form the line cable as not touching on the block.
(Photo 9)
Pay attention that the line cable does not touch
on the packing .
9) Tighten the dome nut.
10) Wind the self-bonding tape between the surface
of dome nut and the end of cable.
(photo9)
12
Concerning the installation of cables
] Ground earth terminal of the power cable securely
In case that ground does not executed, there is the possibility that destroys the CS.
Because the surge protection by the ground wire can not perform.
] The earthing less than 10ohm (Class A) is desirable.
There is the possibility that the obstacle occurs to sounds and pictures of other
radio devices, when the earthing resistance becomes high.
] Separation distance between cables
Distance (generally 20 cm or more) shall be kept between the line cable and the
power cable for secure installation.
] The shield processing of the cable (maintenance box & breaker box)
Earthing must be executed as for the breaker box.
] Installation of lightening facility
Specifications of the CS do not specify the requirement for the installation of
lightning conductor. Don't connect the lightning cable to FG of the power
supply.
13
WARNING!
FCC RF EXPOSURE COMPLIENCE
] This cell station has been tested and complies with the Federal
Communications Commission (FCC) RF exposure limits for General
Population/Uncontrolled exposure environment.
] The design of this cell station complies with the FCC guidelines
and these international standards. This cell station complies with the
MPE requirements by providing a minimum save-distance between the
antenna and any persons. Please keep the minimum save-distance of 1.15
meters from the cell station .
] Unauthorized alteration, modifications or attachments could
impair its quality, damage the cell station, or result in violation
of FCC regulations.
14
Appendix1:Installation materials (for example)
] Materials
Antenna
Coaxial cable (upper)
Coaxial cable (lower)
Power supply cable
Line cable
Line connector
Stand
Antenna pole
Antenna Arm
Arm fixing block(upper)
Arm fixing block(lower)
Self-bonding tape
Tie band
Quantity
PBS-CS37
2pair
1set
as adequate
as adequate
15
Appendix2:Cable specifications
Kinds
Usage
Coaxial cable Antenna PHS cell
station
Power cable PHS cell
station power
supply
breaker box
Line cable
Specifications
8D-SFA (connector with one-side N style (P))
MAX: 6m
With the 2.0mm2 , 3 cores with the copper shield
tape
Outsize diameter : 9.5 – 13 Ø
Frameresisting: PE cable
The color is designated.
(black, white, green and red)
Cell station - Single line: Ø 0.5mm-4 pairs
Maintenance A category 4 or more with aluminum or copper
box
shield tape
(Shield material 0.05t over)
Outsize diameter : 6 – 8 Ø
Flame resisting: PE cable
Remarks
Accessory of
the antenna
Power cable
the equivalent
for the existing
cell station
Line cable
The equivalent
For the existing
cell station
16

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 17
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:6e80b848-b610-46f9-a996-fb49d480ee41
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2003:09:29 15:53:52+09:00
Create Date                     : 2003:09:29 15:53:52+09:00
Document ID                     : uuid:e6d5c9df-a948-4f77-a0c6-885f4cff029b
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools