Sanyo Stb0810C1 Users Manual
STB1020C1 to the manual 7d29215c-90e3-449e-9284-519af047db1a
2015-01-26
: Sanyo Sanyo-Stb0810C1-Users-Manual-336986 sanyo-stb0810c1-users-manual-336986 sanyo pdf
Open the PDF directly: View PDF 
.
Page Count: 52
| Download | |
| Open PDF In Browser | View PDF |
TECHNICAL & SERVICE MANUAL STB0810C1 STB1010C1 STB1020C1 STB1220C1 STB0811C1 STB1023C1 STB1123C1 STB0823H1 FILE NO. Destination: U.S.A. SANYO 26˝ THROUGH THE WALL AIR CONDITIONERS & HEAT PUMP COOLING ONLY MODEL COOLING & ELECTRIC HEATING MODEL Model No. Product Code No. Model No. Product Code No. STB0810C1–S 1 851 005 66 STB0811C1–S 1 851 005 69 STB1010C1–S 1 851 005 65 STB1023C1–S 1 851 005 51 STB1020C1–S 1 851 005 68 STB1123C1–S 1 851 005 70 STB1220C1–S 1 851 005 67 STB0810C1 STB1010C1 STB1020C1 STB1220C1 HEAT PUMP MODEL Model No. Product Code No. STB0823H1–S 1 851 005 52 STB0811C1 STB1023C1 STB1123C1 STB0823H1 REFERENCE NO. SM700487 IMPORTANT! Please Read Before Starting When Installing Place of Installation • If possible, install the unit in a shady location. This air conditioner meets strict safety and operating standards. As the installer or service person, it is an important part of your job to install or service the system so it operates safely and efficiently. • Install it at a spot where optimum air circulation can be obtained. No chairs or other obstructions are allowed in front of the air conditioner. • Keep enough space from any outside obstruction (wall, bush, etc.). For safe installation and trouble-free operation, you must: Dimension of Wall Opening • Carefully read the INSTRUCTION MANUAL and INSTALLATION INSTRUCTIONS attached to each air conditioner before beginning. Wall opening of 26-1/8" x 15-3/4" is required • Follow each installation or repair step exactly as shown. • Observe all local, state, and national electrical codes. • Pay close attention to all warning and caution notices given in this manual. | Ã C | Ã C 15 3 / 4 Minimum Wall Sleeve Opening This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death. Be sure to use lintel to support the block and brick above the sleeve to retain the weight of the unit This symbol refers to a hazard or unsafe practice which can result in personal injury or product or property damage. If Necessary, Get Help These instructions are all you need for most installation sites and maintenance conditions. If you require help for a special problem, contact our sales/service outlet or your certified dealer for additional instructions. Trim molding (if desired) Caulk (4sides) Room side SPECIAL PRECAUTIONS WARNING 26 1 / 8 Minimum 5" from the floor When Wiring 15 7 / 8 " 16 7 / 8 " Outside Box and receptacle ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH. ONLY A QUALIFIED, EXPERIENCED ELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM. • As a safety measure, it is recommended that two people install the unit. • Hold the unit securely, and be careful not to drop any parts if the air conditioner is being installed on an upper floor of a multistory building. • All wiring must conform to local electrical codes. • Each unit must be properly grounded with a ground (or earth) wire or through the supply wiring. When Servicing • DO NOT, under any circumstances, cut or remove the third (ground) prong from the power cord plug. • Turn the power OFF at the main power box (mains) before opening the unit to check or repair electrical parts and wiring. • DO NOT use an adapter Plug or extension cord. • DO NOT use a damaged power cord, plug, or wall outlet. Replace them immediately. • Keep fingers and clothing away from any moving parts. • DO NOT change the internal wiring or any part of the system. • Clean up the site after you finish, remembering to check that no metal scraps or bits of tools have been left inside the unit being serviced. • DO NOT turn the air conditioner on and off by plugging and unplugging. Use the Operation switch. Others CAUTION When Transporting Be careful when picking up and moving the air conditioner. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin aluminum fins on the air conditioner can cut your fingers. • Ventilate any enclosed areas when installing or testing the refrigeration system. Escaped refrigerant gas, on contact with fire or heat, can produce dangerously toxic gas. • Confirm upon completing installation that no refrigerant gas is leaking. If escaped gas comes in contact with a stove, gas water heater, electric room heater or other heat source, it can produce dangerously toxic gas. i HOW TO USE THIS MANUAL This manual is designed to help service personnel to understand basic functions, operation and possible troubles and their remedies on SANYO 26˝ Through The Wall Air Conditioner. You can use this manual both as a reference to find specific information about the capacity, construction of the unit, and as a source of information to help you set up and maintain the air conditioner. Please use this manual to make your work easier, keep the air conditioner functioning well, and keep your customer satisfied. Please read IMPORTANT ! precautional information on the previous page before you start actual work. SANYO 26˝ THROUGH THE WALL A/C MODEL IDENTIFICATION SANYO 26˝ Through The Wall Air Conditioner is identified by a model number. Cooling or heating capacity, electrical information and special features included on the air conditioner are indicated on the model number. Example STB 1 0 2 3 C 1 Development Flag Type Type C : Cooling STB : SANYO 26˝ Thru the wall Capacity H : Heat Pump Electric Heater Size 0 : No Electric Heater 1 : 1.2 kW 3 : 3.4 kW 08 : 8,000 BTU/h class 10 : 10,000 BTU/h class 11 : 11,000 BTU/h class Power Supply 1 : 60Hz 115 V 2 : 60Hz 230 / 208 V 12 : 12,000 BTU/h class NOTE To identify the correct model number of your air conditioner, you must find the nameplate. The name plate is usually located in front of electric component box (behind the grille). First, remove the grille to access the electric component box. ii Table of Contents Page 1. OPERATING RANGE ............................................................................................................................... 1 2. SPECIFICATIONS 2-1. Unit Specifications .......................................................................................................................... 2 2-2. Major Component Specifications ................................................................................................... 4 2-3. Other Component Specifications.................................................................................................... 6 3. DIMENSIONAL DATA............................................................................................................................... 7 4. REFRIGERANT FLOW DIAGRAM .......................................................................................................... 8 5. PERFORMANCE DATA 5-1. Cooling Capacity ........................................................................................................................... 9 5-2. Heating Capacity ........................................................................................................................... 17 6. ELECTRICAL DATA 6-1. Electrical Characteristics ............................................................................................................... 18 6-2. Electrical Wiring Diagrams ............................................................................................................ 21 6-3. P.C.B. Ass'y (Printed Pattern) ........................................................................................................ 27 7. TROUBLESHOOTING 7-1. Check before and after troubleshooting ........................................................................................ 28 7-2. Air conditioner does not operate .................................................................................................... 29 7-3. Some part of air conditioner does not operate .............................................................................. 31 7-4. Air conditioner operates, but abnormalities are observed ............................................................. 33 7-5. If a sensor is defective ................................................................................................................... 34 8. CHECKING ELECTRICAL COMPONENTS 8-1. Measurement of Insulation Resistance .......................................................................................... 35 8-2. Checking Motor Capacitor .............................................................................................................. 36 8-3. Checking Fan Motor Winding ......................................................................................................... 36 8-4. Checking Compressor Motor Winding............................................................................................ 36 8-5. Checking Thermistor ...................................................................................................................... 36 9. DISASSEMBLY PROCEDURE 9-1. Removing Front Grille..................................................................................................................... 37 9-2. Removing Wall Sleeve ................................................................................................................... 37 9-3. Removing Electrical Component Box ............................................................................................. 37 9-4. Removing Electric Heater............................................................................................................... 38 9-5. Removing Blower Wheel ................................................................................................................ 39 9-6. Removing Evaporator..................................................................................................................... 39 9-7. Removing Condenser..................................................................................................................... 40 9-8. Removing Propeller Fan................................................................................................................. 40 9-9. Removing Fan Motor ...................................................................................................................... 41 10.FUNCTION 10-1. Room temperature Control ............................................................................................................ 42 10-2. Defrosting Operation (Heating)....................................................................................................... 45 APPENDIX .................................................................................................................................................. 46 iii 1. OPERATING RANGE ■ COOLING ONLY MODEL Models STB0810C1 STB1010C1 Temperature Cooling STB1020C1 STB1220C1 Indoor Air Intake Temp. Outdoor Air Intake Temp. Maximum 95°F D.B. / 71°F W.B. 115°F D.B. Minimum 67°F D.B. / 57°F W.B. 67°F D.B. ■ COOLING & ELECTRIC HEATING MODEL Models STB0811C1 STB1023C1 STB1123C1 Cooling Heating Temperature Indoor Air Intake Temp. Outdoor Air Intake Temp. Maximum 95°F D.B. / 71°F W.B. 115°F D.B. Minimum 67°F D.B. / 57°F W.B. 67°F D.B. Maximum 80°F D.B. / 67°F W.B. Minimum — D.B. / — W.B. ■ HEAT PUMP MODEL Model STB0823H1 Cooling Heating Temperature Indoor Air Intake Temp. Maximum 95°F D.B. / 71°F W.B. 115°F D.B. Minimum 67°F D.B. / 57°F W.B. 67°F D.B. Maximum 80°F D.B. / 67°F W.B. 75°F D.B. / 65°F W.B. Minimum — D.B. / — W.B. 17°F D.B. / 15°F W.B. 1 Outdoor Air Intake Temp. 2. SPECIFICATIONS 2-1. Unit Specifications Models STB0810C1 STB1010C1 STB1020C1 Model Number STB1220C1 STB0810C1 STB1010C1 STB1020C1 STB1220C1 115 115 230 / 208 230 / 208 Voltage (V) Performance Cooling Capacity Air Flow....Hi Dihumidification BTU/h CFM (CMM) Pints/h Electrical Rating Available voltage range Cooling Amperes Watts Power factor EER Starting amperes Recommeded Circuit Protection 8,200 270 (7.65) 2.0 V A W % BTU/hW A A 104 ~ 126 8.3 940 98 8.7 43 15 Parallel Plug Type Features Controls / Temperature control Control unit Timer Fan speeds Airflow direction (Indoor) COOLING 10,200 9,700 / 9,500 11,500 / 11,300 270 (7.65) 270 (7.65) 270 (7.65) 2.7 2.6 3.2 10.6 1,200 98 8.5 53 15 Parallel 253 ~ 187 5.0 / 5.3 6.1 / 6.6 1,140 / 1,110 1,350 / 1,330 99 / 100 96 / 97 8.5 / 8.5 8.5 / 8.5 30 34 15 15 Tandem Tandem Mechanical / Thermostat 2 2 Horizontal Vertical Air filter Air exhaust Compressor R22-Amount charged at shipment Refrigerant control Operation sound Indoor : Hi / Lo Outdoor : Hi / Lo Dimensions & Weight Unit dimensions (Refer to page 7) Height Width Depth Package dimensions Height Width Depth Weight Net Shipping Shipping volume OZ 20.1 dB-A dB-A 57 / 55 63 / 60 In In In In In In lbs lbs Cuft 2 Manual Manual Washable Yes Rotary (Hermetic) 28.2 23.3 Capillary tube 60 / 57 60 / 57 68 / 64 68 / 64 28.2 60 / 57 68 / 64 15-3/4 25-15/16 21-1/2 18-5/16 29-1/8 24-11/16 82 93 90 101 89 100 93 104 7.62 DATA SUBJECT TO CHANGE WITHOUT NOTICE. Remarks: Rating conditions are: Cooling : Indoor air temperature 80°F D.B. / 67°F W.B. Heating : Indoor air temperature Outdoor air temperature 95°F D.B. / 75°F W.B. Outdoor air temperature Parallele 115V 15AMP 2 Tandem 230/208V 15AMP 70°F D.B. 47°F D.B. / 43°F W.B. Perpendicular 230/208V 20AMP Wall Receptacles Wall Sleeve Dimension 2 Models STB0811C1 STB1023C1 STB1123C1 Model Number STB0823H1 STB0811C1 STB1023C1 STB1123C1 STB0823H1 115 230 / 208 230 / 208 230 / 208 Voltage (V) Performance Cooling Capacity Heat pump Capacity Electric Heating Capacity Air Flow....Hi Dihumidification Electrical Rating Available voltage range Cooling Amperes Watts Power factor EER Starting amperes Heat pump Amperes Watts COP Electric Heater Amperes Watts Element Recommeded Circuit Protection BTU/h BTU/h BTU/h CFM (CMM) Pints/h V A W % BTU/hW A A W W/W A W kW A Plug Type Features Controls / Temperature control Control unit Timer Fan speeds Airflow direction (Indoor) Air filter Air exhaust Compressor R22-Amount charged at shipment Refrigerant control Operation sound Indoor : Hi / Lo Outdoor : Hi / Lo Dimensions & Weight Unit dimensions (Refer to page 7) Height Width Depth Package dimensions Height Width Depth Weight Net Shipping Shipping volume COOLING & ELECTRIC HEATING HEAT PUMP 8,000 9,500 / 9,300 11,300 / 11,000 8,000 / 7,800 — — — 7,500 / 7,400 4,040 11,250 / 9,200 11,250 / 9,200 11,250 / 9,200 250 (7.08) 250 (7.08) 250 (7.08) 250 (7.08) 2.0 2.6 3.2 2.0 104 ~ 126 8.3 920 96 8.7 43 — — — 12.0 1,350 1.22 15 Parallel 5.0 / 5.3 1,120 / 1,090 97 / 99 8.5 / 8.5 30 — — — 15.5 / 14.2 3,550 / 2,930 3.4 20 253 ~ 187 6.0 / 6.5 1,330 / 1,310 96 / 97 8.5 / 8.5 34 — — — 15.5 / 14.2 3,550 / 2,930 3.4 20 Perpendicular 4.2 / 4.5 940 / 920 97 / 98 8.5 / 8.5 25 4.0 / 4.3 880 / 870 2.5 / 2.5 15.5 / 14.2 3,550 / 2,930 3.4 20 Mechanical / Thermostat 2 Horizontal Vertical OZ 20.1 dB-A dB-A 57 / 55 64 / 61 In In In In In In lbs lbs Cuft 2 2 Manual Manual Washable Yes Rotary (Hermetic) 23.3 27.2 Capillary tube 60 / 56 60 / 56 68 / 62 68 / 62 2 28.2 3 57 / 55 64 / 61 15-3/4 25-15/16 21-1/2 18-5/16 29-1/8 24-11/16 82 93 89 100 95 106 90 101 7.62 DATA SUBJECT TO CHANGE WITHOUT NOTICE. 3 2-2. Major Component Specifications Models STB0810C1 STB1010C1 Model Number STB1020C1 STB1220C1 STB0810C1 STB1010C1 STB1020C1 STB1220C1 Rotary (Hermetic) Rotary (Hermetic) Rotary (Hermetic) Rotary (Hermetic) C-1R62H2D C-R80H2C C-R76H6K C-R95H6C Controller PCB Part No. Controls Control circuit fuse Compressor Type Compressor model ( Parts code No. ) Source ( 80663842-S ) ( 80680342-S ) ( 80677946-S ) ( 80695246-S ) 115V 1-phase 60Hz 115V 1-phase 60Hz 230-208V 1-phase 60Hz 230-208V 1-phase 60Hz Nominal output W 625 800 750 950 Compressor oil ... Amount cc SUNISO 4GSD-T....350 SUNISO 4GSD-T....350 SUNISO 4GSD-T....350 SUNISO 4GSD-T....450 Ω C-R: 1.010 C-R: 0.639 C-R: 2.288 C-R: 1.886 Coil resistance (at 77°F) Safety device Type Overload relay C-S: 5.996 C-S: 2.410 C-S: 5.385 C-S: 0.639 External protector External protector External protector External protector MRA99038-9201 MRA98869-9200 MRA98748-9200 MRA98735-9201 Operating temp. Open °F 293±9 302±9 311±9 293±9 Close °F 156±20 156±20 156±20 156±20 Trip in 6 to sec.at 30.5A Trip in 6 to 16 sec. at 40A Trip in 6 to 16 sec. at 24A Trip in 6 to 16 sec. at 24A 25 35 20 22.5 400 400 400 400 Operating amp.(at 77 °F) Run capacitor µF VAC Fan & Fan Motor Fan Type Indoor (Dia. / Depth) In Outdoor (Dia. / Depth) In Centrifigal (Dia 7-3/32 : Depth 3-17/32) Puropeller (Dia 12-19/32 : Depth 3-3/8) Fan motor model ... Q'ty Source KFC6S-91A1P...1 KFC6S-91A6P...1 115V 1-phase 60Hz 230-208V 1-phase 60Hz 6...1,110(115V) 6...1,080(208V) 1,100(230V) 90 90 No. of poles ... rpm, High (V) Nominal output W Coil resistance (at 68°F) Ω Safety device BLU-BLN: 16.59 WHT-BLN: 33.46 BLU-PNK: 17.19 WHT-PNK: 59.31 Type Operating temp. Open Close Run capacitor WHT-BLN: 60.10 BLU-YEL: 7.84 Thermal protector Thermal protector °F 248±9 248±9 °F 171±27 171±27 µF 16 4 220 440 VAC Heat Exch. Coil Evaporator Coil Aluminum plate fin / Copper tube Rows 2 Fins per inch Face area Condenser ft 2 2 3 19.5 19.5 19.5 15.9 1.049 1.049 1.049 1.049 Coil Aluminum plate fin / Copper tube Rows Fins per inch Face area 2 ft 2 2 3 3 3 18.1 14.1 14.1 18.1 1.075 1.075 1.075 1.075 DATA SUBJECT TO CHANGE WITHOUT NOTICE. 4 Models STB0811C1 STB1023C1 Model Number STB1123C1 STB0823H1 STB0811C1 STB1023C1 STB1123C1 STB0823H1 Controller PCB Part No. 851-0-5171-660-00 Controls POW-STBH Control circuit fuse Compressor Type Compressor model ( Parts code No. ) Source Rotary (Hermetic) Rotary (Hermetic) Rotary (Hermetic) Rotary (Hermetic) C-1R62H2D C-R76H6K C-R95H6C C-1R65H6W ( 80663842-s) ( 80677946-S ) ( 80695246-S ) ( 80665146-S ) 115V 1-phase 60Hz 230-208V 1-phase 60Hz 230-208V 1-phase 60Hz 230-208V 1-phase 60Hz Nominal output W 625 750 950 650 Compressor oil ... Amount cc SUNISO 4GSD-T....350 SUNISO 4GSD-T....350 SUNISO 4GSD-T....450 SUNISO 4GSD-T....350 Ω C-R: 1.010 C-R: 2.288 C-R: 1.886 C-R: 3.311 Coil resistance (at 77°F) Safety devices Type Overload relay C-S: 5.996 C-S: 5.385 C-S: 0.639 C-S: 3.529 External protector External protector External protector External protector MRA99082-9201 MRA98869-9200 MRA98735-9201 MRA99038-9201 Operating temp. Open °F 293±9 311±9 293±9 293±9 Close °F 156±20 156±20 156±20 156±20 Trip in 6 to sec.at 30.5A Trip in 6 to 16 sec. at 24A Trip in 6 to 16 sec. at 24A Trip in 6 to 16 sec. at 16.5A 25 20 22.5 22.5 400 400 400 400 Operating amp.(at 77 °F) Run capacitor µF VAC Fan & Fan Motor Fan Type Indoor (Dia. / Depth) In Outdoor (Dia. / Depth) In Fan motor model ... Q'ty Source No. of poles ... rpm, High (V) Nominal output W Coil resistance (at 68°F) Ω Safety device Type Operating temp. Open Close Run capacitor Centrifigal (Dia 7-3/32 : Depth 3-17/32) Puropeller (Dia 12-19/32 : Depth 3-3/8) KFC6S-91A1P...1 KFC6S-91A6P...1 115V 1-phase 60Hz 230-208V 1-phase 60Hz 6...1,110(115V) 6...1,080(208V) 1,100(230V) 90 90 BLU-BLN: 16.59 WHT-BLN: 60.10 BLU-YEL: 7.84 WHT-BLN: 33.46 BLU-PNK: 17.19 WHT-PNK: 59.31 Thermal protector Thermal protector °F 248±9 248±9 °F 171±27 171±27 µF 16 4 220 440 VAC Heat Exch. Coil Evaporator Coil Aluminum plate fin / Copper tube Rows 2 Fins per inch Face area Condenser ft 2 2 3 19.5 19.5 15.9 14.1 1.049 1.049 1.049 1.049 Coil Aluminum plate fin / Copper tube Rows Fins per inch Face area 3 ft 2 2 3 3 3 18.1 14.1 18.1 14.1 1.075 1.075 1.075 1.075 DATA SUBJECT TO CHANGE WITHOUT NOTICE. 5 2-3. Other Component Specifications Models STB0810C1 STB0811C1 STB1010C1 STB1023C1 STB1020C1 STB1123C1 STB1220C1 STB0823H1 Room Thermostat YTB-2U136 Model Openrating temp. YTB-2U358 STB1020C1 STB0810C1 STB1220C1 STB1010C1 STB0811C1 STB1123C1 Cold °F ON: 65 / OFF: 61±3 (Diff: 4 Deg) Warm °F ON: 90 / OFF:86 PTC Thermister (for compressor start up) STB1023C1 PTH491A04AR470N500 Model STB0810C1 STB0811C1 Resistance at 77°F Ω 47±30% Relay (Heater) VC20A-115-S Model VC20A-230-S STB0811C1 STB1023C1 STB1123C1 Coil rating AC115V , 60Hz AC208/230V , 60Hz Contact rating AC265V , 22A AC265V , 22A AH-H06S AH-H10S Electoric Heater Ass'y Model STB0811C1 STB1023C1 STB0823H1 STB1123C1 Heater Element Rating 1.22 kW , 115V Resistance Ω Watt Dinsty w/in2 Dimension Heater Thermo. In 9.5±1.5% (at 68°F) 13.6±1.5% (at 68°F) 8.9 13.2 Dia 3/8 , Leng 36 Type Dia 3/8 , Leng 36 CS-7L Openrating temp Fuse 3.4 kW , 230V °F OFF : 122±5 / ON : 95±9 Type SF-152U Openrating temp °F 306±5 Power Trnsformer ATR-J64ULN2 Model STB0823H1 Rating Primary AC220V , 60Hz Secondary AC19V , 0.3A Thermister (Room sensor) PBC-41E-S29 Model Resistance STB0823H1 at 32°F kΩ 15±5% Thermister (Outdoor coil) PBC-41E-S14 Model Resistance STB0823H1 at 32°F kΩ 15±5% 4-way Valve (Solenoid coil) CHV-01AQ503UA1(Coil) / CHV-01U1(Valve) Model STB0823H1 Coil raiting AC208/230V (60Hz) , 6W 6 3. DIMENSIONAL DATA Models STB0810C1 STB0811C1 STB1010C1 STB1023C1 STB1020C1 STB1123C1 STB1220C1 STB0823H1 ■ Unit Dimension Top view /16" 15 21 - /2" 1 15 - 3 /4" 25 - Front view Side view Unit : inch ■ Wall Sleeve Dimension ■ Dimension of Wall Opening 26 - /8 1 " Wall opening of 26-1/8˝ x 15-3/4˝ is required /8" 5 15 - /8" 7 16 " 26 Minimum Wall Sleeve Opening 15 - /4" 3 Unit : inch 7 4. REFRIGERANT FLOW DIAGRAM Models STB0810C1 STB0811C1 STB1010C1 STB1023C1 STB1020C1 STB1123C1 STB1220C1 Compressor Condenser Evaporator Accumulator Capillary tube Accumulator Compressor STB0823H1 4-way valve Capillary tube Outdoor heat exchanger Indoor heat exchanger Model Capillary tube Cooling cycle Check valve 8 Heating cycle 5. PERFORMANCE DATA 5-1. Cooling Capacity Model STB0810C1 115 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 8,200 BTU/h 270 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 8,260 0.60 6,260 7,310 8,260 8,260 8,260 8,260 9,350 0.62 5,170 6,220 7,270 8,320 8,860 8,860 9,430 0.64 4,050 5,100 6,150 7,200 8,250 9,300 10,000 0.66 3,970 5,020 6,070 7,120 8,170 10,610 0.67 3,850 4,900 5,950 7,000 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 7,900 7,540 7,180 6,750 0.65 0.70 0.75 0.79 6,100 5,940 5,780 5,580 7,150 6,990 6,830 6,630 7,900 7,540 7,180 6,750 7,900 7,540 7,180 6,750 7,900 7,540 7,180 6,750 7,900 7,540 7,180 6,750 8,480 8,090 7,710 7,250 0.67 0.72 0.77 0.81 5,010 4,840 4,680 4,490 6,060 5,890 5,730 5,540 7,110 6,940 6,780 6,590 8,160 7,990 7,710 7,250 8,480 8,090 7,710 7,250 8,480 8,090 7,710 7,250 9,020 8,610 # 8,200 7,710 0.69 0.74 0.79 0.84 3,890 3,730 3,570 3,380 4,940 4,780 4,620 4,430 5,990 5,830 5,670 5,480 7,040 6,870 6,720 6,530 8,090 7,920 7,770 7,580 9,020 8,610 8,200 7,710 9,560 9,130 8,690 8,170 0.71 0.76 0.82 0.86 3,820 3,660 3,500 3,320 4,860 4,710 4,550 4,370 5,910 5,760 5,600 5,420 6,960 6,810 6,650 6,470 8,010 7,860 7,700 7,520 10,150 9,670 9,130 8,540 0.73 0.78 0.84 0.89 3,690 3,530 3,360 3,170 4,740 4,580 4,400 4,220 5,790 5,630 5,450 5,260 6,840 6,680 6,500 6,310 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 9 110 (43.3) 6,210 0.84 5,350 6,210 6,210 6,210 6,210 6,210 6,670 0.86 4,260 5,310 6,360 6,670 6,670 6,670 7,090 0.89 3,150 4,200 5,250 6,290 7,090 7,090 7,520 0.91 3,090 4,140 5,190 6,240 7,290 7,950 0.94 2,970 4,020 5,070 6,120 Model STB1010C1 115 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 10,200 BTU/h 270 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 10,280 0.80 7,220 8,270 9,320 10,280 10,280 10,280 11,630 0.82 6,130 7,180 8,230 9,280 10,330 11,030 11,730 0.85 5,000 6,050 7,090 8,140 9,190 10,240 12,430 0.87 4,900 5,950 7,000 8,050 9,100 13,190 0.89 4,760 5,810 6,850 7,900 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 9,830 9,380 8,940 8,390 0.87 0.93 1.00 1.06 7,000 6,790 6,580 6,320 8,050 7,840 7,630 7,370 9,100 8,890 8,680 8,390 9,830 9,380 8,940 8,390 9,830 9,380 8,940 8,390 9,830 9,380 8,940 8,390 10,550 10,070 9,590 9,010 0.89 0.95 1.02 1.09 5,910 5,700 5,490 5,240 6,960 6,750 6,540 6,290 8,010 7,800 7,580 7,330 9,060 8,850 8,630 8,380 10,110 9,900 9,590 9,010 10,550 10,070 9,590 9,010 11,220 10,710 # 10,200 9,590 0.92 0.98 1.05 1.12 4,780 4,570 4,360 4,110 5,830 5,620 5,410 5,160 6,880 6,670 6,460 6,210 7,930 7,720 7,510 7,260 8,980 8,770 8,560 8,310 10,030 9,820 9,610 9,360 11,890 11,350 10,810 10,160 0.94 1.01 1.08 1.15 4,690 4,480 4,280 4,040 5,740 5,530 5,330 5,090 6,790 6,580 6,380 6,140 7,840 7,630 7,430 7,190 8,890 8,680 8,480 8,240 12,620 12,030 11,350 10,630 0.97 1.04 1.11 1.18 4,550 4,340 4,100 3,860 5,600 5,390 5,150 4,900 6,650 6,440 6,200 5,950 7,700 7,490 7,250 7,000 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 10 110 (43.3) 7,730 1.13 6,020 7,070 7,730 7,730 7,730 7,730 8,290 1.15 4,930 5,980 7,030 8,080 8,290 8,290 8,820 1.19 3,810 4,860 5,910 6,960 8,010 8,820 9,350 1.22 3,740 4,790 5,840 6,890 7,940 9,880 1.26 3,610 4,650 5,700 6,750 Model STB1020C1 230 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 9,700 BTU/h 270 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 9,770 0.76 6,980 8,030 9,080 9,770 9,770 9,770 11,060 0.78 5,890 6,940 7,990 9,040 10,090 10,490 11,150 0.80 4,760 5,810 6,860 7,910 8,960 10,010 11,820 0.83 4,670 5,720 6,770 7,820 8,870 12,550 0.84 4,530 5,580 6,630 7,680 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 9,350 8,920 8,500 7,980 0.82 0.88 0.94 0.97 6,780 6,580 6,380 6,140 7,830 7,630 7,430 7,190 8,880 8,680 8,480 7,980 9,350 8,920 8,500 7,980 9,350 8,920 8,500 7,980 9,350 8,920 8,500 7,980 10,030 9,570 9,120 8,570 0.84 0.90 0.97 1.00 5,690 5,490 5,290 5,050 6,740 6,540 6,340 6,100 7,790 7,580 7,390 7,150 8,840 8,630 8,440 8,200 9,890 9,570 9,120 8,570 10,030 9,570 9,120 8,570 10,670 10,180 # 9,700 9,120 0.87 0.93 1.00 1.03 4,560 4,360 4,160 3,930 5,610 5,410 5,210 4,980 6,660 6,460 6,260 6,030 7,710 7,510 7,310 7,080 8,760 8,560 8,360 8,130 9,810 9,610 9,410 9,120 11,310 10,800 10,280 9,670 0.89 0.96 1.03 1.06 4,470 4,280 4,090 3,860 5,520 5,330 5,140 4,910 6,570 6,380 6,190 5,960 7,620 7,430 7,240 7,010 8,670 8,480 8,290 8,060 12,000 11,440 10,800 10,110 0.92 0.98 1.05 1.09 4,340 4,140 3,920 3,690 5,390 5,190 4,970 4,740 6,440 6,240 6,020 5,790 7,490 7,290 7,070 6,840 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 11 110 (43.3) 7,350 1.00 5,860 6,910 7,350 7,350 7,350 7,350 7,890 1.02 4,760 5,810 6,860 7,890 7,890 7,890 8,390 1.06 3,650 4,700 5,750 6,800 7,850 8,390 8,890 1.09 3,580 4,630 5,680 6,730 7,780 9,400 1.12 3,450 4,500 5,550 6,600 Model STB1220C1 230 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 11,500 BTU/h 270 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 11,590 0.92 7,880 8,930 9,980 11,030 11,590 11,590 13,110 0.94 6,790 7,840 8,890 9,940 10,990 12,040 13,220 0.97 5,650 6,700 7,750 8,800 9,850 10,900 14,020 1.00 5,550 6,600 7,650 8,700 9,750 14,880 1.02 5,380 6,430 7,480 8,530 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 11,080 10,580 10,070 9,460 0.99 1.06 1.14 1.21 7,620 7,370 7,130 6,830 8,670 8,420 8,180 7,880 9,720 9,470 9,230 8,930 10,770 10,520 10,070 9,460 11,080 10,580 10,070 9,460 11,080 10,580 10,070 9,460 11,890 11,350 10,810 10,160 1.02 1.09 1.17 1.24 6,530 6,280 6,040 5,740 7,580 7,330 7,090 6,790 8,630 8,380 8,140 7,840 9,680 9,430 9,190 8,890 10,730 10,480 10,230 9,940 11,780 11,350 10,810 10,160 12,650 12,070 # 11,500 10,810 1.05 1.13 1.21 1.28 5,400 5,150 4,900 4,620 6,450 6,200 5,950 5,670 7,500 7,250 7,000 6,720 8,550 8,300 8,050 7,770 9,600 9,350 9,100 8,810 10,650 10,400 10,150 9,860 13,410 12,800 12,190 11,460 1.08 1.16 1.24 1.32 5,300 5,050 4,810 4,530 6,350 6,100 5,860 5,580 7,400 7,150 6,910 6,630 8,450 8,200 7,960 7,680 9,500 9,250 9,010 8,730 14,230 13,560 12,800 11,980 1.11 1.19 1.27 1.35 5,140 4,890 4,620 4,330 6,190 5,940 5,670 5,380 7,240 6,990 6,720 6,430 8,290 8,040 7,770 7,480 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 12 110 (43.3) 8,710 1.28 6,480 7,530 8,580 8,710 8,710 8,710 9,350 1.31 5,390 6,440 7,490 8,540 9,350 9,350 9,950 1.35 4,260 5,310 6,360 7,410 8,460 9,510 10,540 1.39 4,190 5,230 6,280 7,330 8,380 11,140 1.43 4,040 5,090 6,140 7,190 Model STB0811C1 115 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 8,000 BTU/h 250 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 8,060 0.59 5,970 6,940 7,910 8,060 8,060 8,060 9,120 0.61 4,960 5,930 6,900 7,870 8,650 8,650 9,200 0.62 3,920 4,890 5,860 6,830 7,800 8,780 9,750 0.64 3,840 4,810 5,790 6,760 7,730 10,350 0.65 3,720 4,690 5,660 6,640 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 7,710 7,360 7,010 6,580 0.64 0.68 0.73 0.79 5,810 5,650 5,490 5,300 6,780 6,620 6,460 6,270 7,710 7,360 7,010 6,580 7,710 7,360 7,010 6,580 7,710 7,360 7,010 6,580 7,710 7,360 7,010 6,580 8,270 7,900 7,520 7,070 0.65 0.70 0.75 0.81 4,800 4,630 4,470 4,290 5,770 5,610 5,450 5,260 6,740 6,580 6,420 6,230 7,710 7,550 7,390 7,070 8,270 7,900 7,520 7,070 8,270 7,900 7,520 7,070 8,800 8,400 # 8,000 7,520 0.67 0.72 0.77 0.84 3,750 3,600 3,440 3,250 4,730 4,570 4,410 4,220 5,700 5,540 5,380 5,200 6,670 6,510 6,350 6,170 7,640 7,480 7,330 7,140 8,610 8,400 8,000 7,520 9,330 8,900 8,480 7,970 0.69 0.74 0.80 0.86 3,680 3,530 3,370 3,190 4,660 4,500 4,350 4,160 5,630 5,470 5,320 5,130 6,600 6,440 6,290 6,110 7,570 7,420 7,260 7,080 9,900 9,430 8,900 8,340 0.71 0.76 0.82 0.88 3,570 3,410 3,230 3,040 4,540 4,380 4,200 4,020 5,510 5,350 5,180 4,990 6,480 6,320 6,150 5,960 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 13 110 (43.3) 6,060 0.85 5,070 6,040 6,060 6,060 6,060 6,060 6,500 0.87 4,050 5,030 6,000 6,500 6,500 6,500 6,920 0.90 3,020 3,990 4,970 5,940 6,910 6,920 7,340 0.92 2,970 3,940 4,910 5,880 6,850 7,750 0.95 2,860 3,830 4,800 5,770 Model STB1023C1 230 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 9,500 BTU/h 250 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 9,570 0.74 6,700 7,670 8,640 9,570 9,570 9,570 10,830 0.76 5,690 6,660 7,630 8,600 9,580 10,270 10,930 0.79 4,640 5,610 6,580 7,550 8,530 9,500 11,580 0.81 4,550 5,520 6,500 7,470 8,440 12,290 0.83 4,410 5,380 6,360 7,330 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 9,160 8,740 8,320 7,820 0.80 0.86 0.92 0.96 6,500 6,300 6,100 5,860 7,470 7,270 7,070 6,840 8,440 8,240 8,040 7,810 9,160 8,740 8,320 7,820 9,160 8,740 8,320 7,820 9,160 8,740 8,320 7,820 9,820 9,380 8,930 8,390 0.83 0.88 0.95 0.99 5,490 5,290 5,090 4,850 6,460 6,260 6,060 5,830 7,430 7,230 7,030 6,800 8,400 8,200 8,000 7,770 9,370 9,170 8,930 8,390 9,820 9,380 8,930 8,390 10,450 9,980 # 9,500 8,930 0.85 0.91 0.98 1.02 4,440 4,240 4,040 3,810 5,410 5,210 5,020 4,790 6,380 6,180 5,990 5,760 7,350 7,150 6,960 6,730 8,320 8,130 7,930 7,700 9,300 9,100 8,900 8,670 11,080 10,570 10,070 9,470 0.87 0.94 1.01 1.05 4,350 4,160 3,970 3,740 5,330 5,130 4,940 4,710 6,300 6,100 5,910 5,690 7,270 7,080 6,880 6,660 8,240 8,050 7,860 7,630 11,760 11,200 10,570 9,900 0.90 0.96 1.03 1.08 4,220 4,020 3,800 3,570 5,190 5,000 4,780 4,540 6,160 5,970 5,750 5,520 7,140 6,940 6,720 6,490 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 14 110 (43.3) 7,200 1.01 5,580 6,550 7,200 7,200 7,200 7,200 7,720 1.03 4,570 5,540 6,510 7,480 7,720 7,720 8,220 1.07 3,530 4,500 5,470 6,450 7,420 8,220 8,710 1.10 3,460 4,440 5,410 6,380 7,350 9,210 1.13 3,340 4,310 5,280 6,250 Model STB1123C1 230 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 11,300 BTU/h 250 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 11,380 0.90 7,610 8,590 9,560 10,530 11,380 11,380 12,890 0.93 6,610 7,580 8,550 9,520 10,490 11,470 13,000 0.96 5,550 6,520 7,490 8,460 9,430 10,410 13,770 0.98 5,450 6,420 7,390 8,360 9,330 14,620 1.00 5,290 6,260 7,230 8,200 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 10,890 10,400 9,900 9,300 0.98 1.04 1.12 1.19 7,360 7,110 6,860 6,570 8,330 8,080 7,830 7,540 9,300 9,050 8,800 8,510 10,280 10,020 9,780 9,300 10,890 10,400 9,900 9,300 10,890 10,400 9,900 9,300 11,680 11,150 10,620 9,980 1.00 1.07 1.15 1.22 6,350 6,100 5,850 5,560 7,320 7,070 6,820 6,530 8,290 8,040 7,790 7,500 9,270 9,010 8,770 8,470 10,240 9,990 9,740 9,450 11,210 10,960 10,620 9,980 12,430 11,870 # 11,300 10,620 1.03 1.11 1.19 1.26 5,290 5,040 4,800 4,510 6,260 6,020 5,770 5,480 7,240 6,990 6,740 6,450 8,210 7,960 7,710 7,430 9,180 8,930 8,690 8,400 10,150 9,900 9,660 9,370 13,180 12,580 11,980 11,260 1.06 1.14 1.22 1.30 5,200 4,950 4,710 4,430 6,170 5,920 5,680 5,400 7,140 6,890 6,650 6,370 8,110 7,870 7,630 7,340 9,080 8,840 8,600 8,310 13,980 13,320 12,580 11,770 1.09 1.17 1.25 1.33 5,040 4,790 4,520 4,230 6,020 5,770 5,490 5,200 6,990 6,740 6,460 6,170 7,960 7,710 7,430 7,140 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 15 110 (43.3) 8,560 1.26 6,210 7,180 8,160 8,560 8,560 8,560 9,190 1.29 5,200 6,170 7,150 8,120 9,090 9,190 9,770 1.33 4,160 5,130 6,100 7,070 8,040 9,020 10,360 1.37 4,080 5,050 6,020 6,990 7,970 10,950 1.41 3,940 4,910 5,880 6,850 Model STB0823H1 230 V Single phase 60 Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °F (°C) W.B. D.B. 59 (15.0) 63 (17.2) 67 (19.4) 70 (21.1) 73 (22.8) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 70 (21.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 73 (22.8) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 77 (25.0) 80 (26.7) 84 (28.9) 88 (31.1) 8,000 BTU/h 250 CFM TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC SHC TC CM SHC SHC SHC SHC 67 (19.4) 8,060 0.61 5,980 6,950 7,920 8,060 8,060 8,060 9,120 0.62 4,960 5,940 6,910 7,880 8,650 8,650 9,200 0.64 3,920 4,890 5,870 6,840 7,810 8,780 9,750 0.66 3,850 4,820 5,790 6,760 7,740 10,350 0.67 3,730 4,700 5,670 6,640 CONDENSER OUTDOOR AMBIENT TEMP. °F( °C) 75 85 95 105 (23.9) (29.4) (35.0) (40.6) 7,710 7,360 7,010 6,580 0.66 0.70 0.75 0.80 5,810 5,650 5,490 5,300 6,790 6,630 6,470 6,270 7,710 7,360 7,010 6,580 7,710 7,360 7,010 6,580 7,710 7,360 7,010 6,580 7,710 7,360 7,010 6,580 8,270 7,900 7,520 7,070 0.67 0.72 0.77 0.82 4,800 4,640 4,480 4,290 5,770 5,610 5,450 5,260 6,750 6,580 6,430 6,240 7,720 7,560 7,400 7,070 8,270 7,900 7,520 7,070 8,270 7,900 7,520 7,070 8,800 8,400 # 8,000 7,520 0.69 0.74 0.80 0.85 3,760 3,600 3,450 3,260 4,730 4,570 4,420 4,230 5,700 5,550 5,390 5,200 6,680 6,520 6,360 6,170 7,650 7,490 7,330 7,150 8,620 8,400 8,000 7,520 9,330 8,900 8,480 7,970 0.71 0.76 0.82 0.87 3,690 3,530 3,380 3,200 4,660 4,510 4,350 4,170 5,630 5,480 5,320 5,140 6,610 6,450 6,300 6,110 7,580 7,420 7,270 7,090 9,900 9,430 8,900 8,340 0.73 0.78 0.84 0.90 3,570 3,410 3,240 3,050 4,550 4,390 4,210 4,020 5,520 5,360 5,180 5,000 6,490 6,330 6,150 5,970 TC : Total Cooling Capacity (BTU/h) SHC : Sensible Heat Capacity (BTU/h) CM : Compressor Input (kW) Rating conditions (#Mark) are Outdoor Ambient Temp. 95°F (35°C) D.B. Indoor Air Intake Temp. 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. 16 110 (43.3) 6,060 0.85 5,070 6,040 6,060 6,060 6,060 6,060 6,500 0.87 4,060 5,030 6,000 6,500 6,500 6,500 6,920 0.90 3,030 4,000 4,970 5,950 6,920 6,920 7,340 0.92 2,970 3,950 4,920 5,890 6,860 7,750 0.95 2,860 3,830 4,810 5,780 5-2. Heating Capacity (Heat pump Performance) STB0823H1 Fan speed : High Heating capacity ratio (%) Model 120 110 100 90 80 70 60 50 40 30 20 10 0 17 20 30 40 47 50 60 Outdoor ambient temperature (°F DB) NOTE 1) ● … Point of rating condition Black dot in the chart indicates the following rating condition. Indoor: 70°F (21.1°C) D.B. Outdoor: 47°F (8.3°C) D.B. / 43°F (6.1°C) W.B. 2) Above characteristics indicates heat pump heating operation, which does not include elctric heater operation. 3) Because this air conditioner heats a room by drawing in the heat of the outside air (heat pump system), the heating efficiency will fall off when the outdoor temperature is very low, which consequently makes the room temperature decrease. At this time, heat is provided by the electric heater instead of heat pump. See page 44 for detail. 17 6. ELECTRICAL DATA 6-1. Electrical Characteristics Cooling only models Model STB0810C1 Outdoor Unit Fan Motor Performance at Rating Conditions Compressor 115V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input Model Complete Unit A 1.26 7.04 8.3 kW 0.145 0.795 0.94 A 1.26 8.34 9.6 kW 0.145 0.935 1.08 STB1010C1 Outdoor Unit Fan Motor Performance at Rating Conditions 115V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input Model Complete Unit Compressor A 1.26 9.34 10.6 kW 0.145 1.055 1.20 A 1.26 11.04 12.3 kW 0.145 1.255 1.40 STB1020C1 Outdoor Unit Fan Motor Performance at Rating Conditions Compressor 230 / 208V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input Model Complete Unit A 0.61 / 0.64 kW 0.142 / 0.132 A 0.61 / 0.64 kW 0.142 / 0.132 4.39 / 4.66 0.998 / 0.978 4.99 / 5.26 1.118 / 1.098 5.0 1.14 5.6 1.26 / 5.3 / 1.11 / 5.9 / 1.23 STB1220C1 Outdoor Unit Fan Motor Performance at Rating Conditions Complete Unit Compressor 230 / 208V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input A 0.61 / 0.64 kW 0.142 / 0.132 A 0.61 / 0.64 kW 0.142 / 0.132 Rating Conditions 5.49 / 5.96 1.208 / 1.198 6.29 / 6.96 1.428 / 1.438 6.1 1.35 6.9 1.57 / / 1.33 / 7.6 / 1.57 : Indoor Air Temperature 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. Outdoor Air Temperature 95°F (35°C) D.B. Full Load Conditions : Indoor Air Temperature 90°F (32.2°C) D.B. / 73°F (22.8°C) W.B. Outdoor Air Temperature 110°F (43.3°C) D.B. 18 6.6 Cooling & electric heating models Model STB0811C1 Outdoor Unit Fan Motor Performance at Rating Conditions Compressor 115V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input Model Complete Unit A 1.26 7.04 8.3 kW 0.145 0.775 0.92 A 1.26 8.34 9.6 kW 0.145 0.945 1.09 STB1023C1 Outdoor Unit Fan Motor Performance at Rating Conditions 230 / 208V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input Model Complete Unit Compressor A 0.61 / 0.64 kW 0.142 / 0.132 A 0.61 / 0.64 kW 0.142 / 0.132 4.39 / 4.66 0.978 / 0.958 4.99 / 5.26 1.128 / 1.088 5.0 1.12 5.6 1.27 / 5.3 / 1.09 / 5.9 / 1.22 STB1123C1 Outdoor Unit Fan Motor Performance at Rating Conditions Complete Unit Compressor 230 / 208V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input A 0.61 / 0.64 kW 0.142 / 0.132 A 0.61 / 0.64 kW 0.142 / 0.132 Rating Conditions 5.39 / 5.86 1.188 / 1.178 6.29 / 6.86 1.408 / 1.408 6.0 1.33 6.9 1.55 / / 7.5 / 1.54 : Indoor Air Temperature 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. Outdoor Air Temperature 95°F (35°C) D.B. Full Load Conditions : Indoor Air Temperature 90°F (32.2°C) D.B. / 73°F (22.8°C) W.B. Outdoor Air Temperature 110°F (43.3°C) D.B. 19 6.5 / 1.31 Heat pump model Model STB0823H1 COOLING Outdoor Unit Fan Motor Performance at Rating Conditions Complete Unit Compressor 230 / 208V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input A 0.61 / 0.64 kW 0.142 / 0.132 A 0.61 / 0.64 kW 0.142 / 0.132 3.59 / 3.86 0.798 / 0.788 4.29 / 4.46 0.948 / 0.918 4.2 0.94 4.9 1.09 / 4.5 / 0.92 / 5.1 / 1.05 Rating Conditions : Indoor Air Temperature 80°F (26.7°C) D.B. / 67°F (19.4°C) W.B. Outdoor Air Temperature 95°F (35°C) D.B. Full Load Conditions : Indoor Air Temperature 90°F (32.2°C) D.B. / 73°F (22.8°C) W.B. Outdoor Air Temperature 110°F (43.3°C) D.B. HEATING Outdoor Unit Fan Motor Performance at Rating Conditions Compressor 230 / 208V 1-phase 60Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input Rating Conditions Complete Unit A 0.61 / 0.64 kW 0.142 / 0.132 A 0.61 / 0.64 kW 0.142 / 0.132 3.39 / 3.66 0.738 / 0.738 4.09 / 4.51 0.898 / 0.888 4.0 0.88 4.7 1.04 / / 5.2 / 1.02 : Indoor Air Temperature 70°F (21.1°C) D.B. Outdoor Air Temperature 47°F (8.3°C) D.B. / 43°F (6.1°C) W.B. Full Load Conditions : Indoor Air Temperature 80°F (26.7°C) D.B. Outdoor Air Temperature 75°F (23.9°C) D.B. / 65°F (18.3°C) W.B. 20 4.3 / 0.87 WARNING 6-2. Electrical Wiring Diagrams Models STB0810C1 To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical STB1010C1 LAYOUT FOR ELECTRIC PARTS Room thermo Main switch Capacitor (FM) Fancycle switch Capacitor (CM) Clip power cord Thermistor 21 WARNING Models STB1020C1 To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts. STB1220C1 LAYOUT FOR ELECTRIC PARTS Room thermo Main switch Capacitor (FM) Fancycle switch Capacitor (CM) Clip power cord 22 WARNING Model To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts. STB0811C1 LAYOUT FOR ELECTRIC PARTS Main switch Room thermo Capacitor (FM) Fancycle switch Capacitor (CM) Relay heater 23 Thermistor To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts. WARNING Models STB1023C1 STB1123C1 LAYOUT FOR ELECTRIC PARTS Main switch Room thermo Capacitor (FM) Fancycle switch Capacitor (CM) Relay heater 24 WARNING Model STB0823H1 25 To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts. WARNING Model To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts. STB0823H1 LAYOUT FOR ELECTRIC PARTS Varistor Main control switch Capacitor (FM) Control switch temp. setting Fan switch Lid Thermistor room temp. Power pack control PCB Power cord Power transformer Capacitor (CM) BEFORE OPENING THE BOX AFTER OPENING THE BOX 26 6-3. P.C.B. Ass'y (Printed Pattern) POW–STBH (For model STB0823H1) 27 7. TROUBLESHOOTING 7-1. Check before and after troubleshooting WARNING Hazardous voltage can cause ELECTRIC SHOCK or DEATH. Disconnect power or turn off circuit breaker before you start checking or servicing. 7-1-1. Check power supply. ● Check that voltage is in specified range (±10% of the rating). ● Check that power is being supplied. 7-1-2. Check lead wires and connectors. ● Check that coating of lead wires is not damaged. ● Check that lead wires and connectors are firmly connected. ● Check that wiring is correct. 28 7-2. Air conditioner does not operate. 7-2-1. Circuit breaker trips (or fuse blows). A. When the circuit breaker is set to ON, it is tripped soon. (Resetting is not possible.) ● There is a possibility of ground fault. ● Check insulation resistance. If resistance value is 2MΩ or less, insulation is defective (“NO”). Wall outlet (Receptacle) Power plug 1 Circuit breaker Window type air conditioner Power supply Ground WARNING * Set circuit breaker to OFF. 1 Pull the power plug out of the wall outlet. • Measure insulation resistance of unit. Insulation of unit is defective. NO • Measure insulation resistance of electrical parts. (Example) Compressor, Fan motor, Capacitor, Relay etc. NOTE 1. If any poorly insulated part is found, exclude that part from circuit with other parts properly connected, and then measure insulation resistance of entire air conditioner again to locate defective part. 2. Replace defective part with new one. 29 B. Circuit breaker trips in several minutes after turning the air conditioner on. ● There is a possibility of short circuit. • Check capacity of circuit breaker. Replace with suitable one (larger capacity). NO Capacity of circuit breaker is suitable. (Only for heat pump model) • Measure resistance of 4-way valve's winding. • Measure resistance of fan motor winding. • Measure resistance of compressor motor winding. 7-2-2. Neither fan motor nor compressor motor runs. A. Power is not supplied. • Check power supply. Circuit breaker is tripped. Reset breaker. Power failure Wait for recovery or contact power company. NO Power is being supplied to the unit. B. Check "MODE selector" on the control panel. (Cooling only models) and (Cooling & electric heating models) Set to "COOL". • Check that MODE selector switch is not set at "OFF". If it is set at OFF. (Heat pump model) Set to "COOL" or "HEAT". C. Check transformer. (Only for heat pump model) • Check continuity of primary and secondary winding to see if the lead wires are disconnected. 30 Check PCB Ass'y. 7-3. Some part of air conditioner does not operate. 7-3-1. Only fan does not run. • Check fan rotation. Turn fan gently once or twice by hand. • Check fan casing foreign matter on inside. Fan cannot be turned. Fan motor burnout or foreign matter in bearings. • Measure resistance of fan motor winding. OK • Check fan motor capacitor and 4P-connectors (Socket and Plug). (Only for heat pump model) • Check PCB Ass'y . (Power pack) 7-3-2. Electric heater does not work. Both for (cooling & electric heating models) and (heat pump model) • Measure resistance of electric heater winding. • Measure coil resistance of heater relay. • Check to see if the circuit of heater thermostat is opened or closed ? • Check continuity for thermal fuses. Blown Replace them. (Only for heat pump model) • Check PCB Ass'y. (Power pack) 31 Remove foreign matter or repair. Repair or replace. 7-3-3. Only compressor unit does not run. A. Check setting temperature. COOL mode HEAT mode (Only for heat pump model) Is room temperature too low ? Is room temperature too high ? NO NO Try to lower setting temperature by thermostat knob cooler. Try to raise setting temperature by thermostat knob warmer. B. Check compressor and electrical parts. Overload relay is working. (OLR) • Check compressor motor capacitor. YES • Measure resistance of compressor motor winding. Temperature of compressor is abnormally high. YES (Only for 115V models) • Check PTC thermistor. YES Refrigerant gas shortage. Charge refrigerant gas (R22). NO Rotor may be locked up. Cooling only models CAUTION Cooling & electric heating models ● If the unit is turned off during cooling, DO NOT restart it immediately, as this can damage it. Wait at least 3 minutes or so before starting it again. Heat pump model ● The compressor does not start up immediately even when the MODE selector switch is set to COOL or HEAT (It starts operating in about 3 minutes). ● This is because rough 3-minute timer is built into the heat pump model in order to protect the compressor. When operation is started up or restarted, the fan operation begins immediately but the compressor starts operating after about 3-minute lag. 32 7-4. Air conditioner operates, but abnormalities are observed. 7-4-1. Operation does not switch from HEAT to COOL (or COOL to HEAT). (Only for heat pump model) • Measure resistance of 4–way valve's winding. OK Check PCB Ass'y . (Power pack) 7-4-2. Poor cooling or heating. • Measure temperature of suction and discharge air of air conditioner. Temperature difference is small. Possibility of gas shortage. Charge refrigerant gas (R22). Temperature difference between suction and discharge air is large enough (In cooling operation: approx. 14 °F or more). • Check for clogging of air filter. Clean filter. Air filter is clogged. • Fan speed is set to LOW. YES Set fan speed to HIGH. Reduce cooling or heating load or replace the air conditioner with larger capacity. • Review cooling load estimate, if performance of air conditioner is normal. 7-4-3. Excessive cooling or heating. • Set temperature is suitable. NO Set temperature to higher or lower value using thermostat. 33 7-5. If a sensor is defective. (Only for heat pump model) 7-5-1. Room temp. thermistor (RTH) is defective. A. Open When thermistor opens, the air conditioner will be in the following conditions as the controller tries to detect extremely low room temperature. a) In Cooling mode: The air conditioner soon stops and will not start again. (Thermo.OFF) Compressor does not run. b) In Heating mode: The air conditioner continues to operate. (Thermo.ON) (Heat pump) Electric heater does not stop. As a result, the room becomes too warm. Temperature sensor B. Short Lead wires When thermistor is short, the air conditioner will be in the following conditions as the controller tries to detect extremely high room temperature. Thermistor Structure a) In Cooling mode: The air conditioner continues to operate. (Thermo.ON) Compressor does not stop. As a result, the room becomes too cold. b) In Heating mode: The air conditioner soon stops and will not start again. (Thermo.OFF) (Heat pump) Neither compressor nor electric heater runs. NOTE Definition of Open or Short Circuit of Sensor (Thermistor) Open... A lead wire is broken or disconnected or the circuit inside the temperature sensor is open . Short... The protective cover of a lead wire has been damaged, and the exposed wire is touching another metal part, or both lead wires have become exposed and are touching each other. Alternatively, the circuit inside the temperature sensor is closed. 34 8. CHECKING ELECTRICAL COMPONENTS 8-1. Measurement of Insulation Resistance Power plug ● The insulation is in good condition if the resistance exceeds 2MΩ. Ground Probe 8-1-1. Power Cord and Unit Insulation tester Clamp the grounding prong of the power plug with a lead clip of the insulation resistance tester and measure the resistance by placing a probe on either of the two power blade. (Fig. 1) Fig. 1 NOTE The shape of the power plug may differ from that of the air conditioner which you are servicing. Then, also measure the resistance between the grounding prong and other power blade. (Fig. 1) Probe 8-1-2. Measurement of Insulation Resistance for Electrical Parts Disconnect the lead wires of the desired electric part from terminal plate, switch, capacitor, etc. Similarly disconnect the connector. Then measure the insulation resistance. (Figs. 2 to 3) Clip Copper tube or metallic part Insulation tester Refer to Electric Wiring Diagram. Fig. 2 From fan motor, compressor and other parts NOTE If the probe cannot enter the poles because the hole is too narrow then use a probe with a thinner pin. Metallic part Probe Clip Insulation tester Fig. 3 Fig. 4 35 8-2. Checking Motor Capacitor Remove the lead wires from the capacitor terminals, and then place probes on the capacitor terminals as shown in Fig. 4. Observe the deflection of the pointer, setting the resistance measuring range of the multimeter to the maximum value. Multimeter The capacitor is “good” if the pointer bounces to a great extent and then gradually returns to its original position. The range of deflection and deflection time differ according to the capacity of the capacitor. 8-3. Checking Fan Motor Winding Referring to the electrical diagram, disconnect fan motor connectors, and measure the resistance between each lead wire with a multimeter. Compressor motor capacitor The multimeter should be set in the X1 range. If the fan motor is hot, allow a few minutes until it gets cooled down. Fan motor capacitor When the resistances between each lead wire are those listed in "2-2. Major Component Specifications" the fan motor should be normal. Fig. 4 8-4. Checking Compressor Motor Winding Checking compressor motor winding can be done in the similar manner. Multimeter Remove the terminal cover of the compressor motor, setting the resistance measuring range of the multimeter to "X1Ω" and check the continuity between each pair out of the 3 terminals as shown in Fig. 5. Refer to "2-2. Major Component Specifications" for coil resistance. ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, ,,,,,,,,,, Compressor motor coil terminal Fig. 5 8-6. Checking Thermistor (Only for heat pump model) Unplug the 2P connector connected to PCB Ass´y and measure the resistance of the thermistor with a multimeter, which is set in the X1 kΩ range. If the thermistor is normal, the multimeter should read approximately 15kΩ at 32˚F. 36 9. DISASSEMBLY PROCEDURE 9-1. Removing Front Grille Wall sleeve Front grille 1) Pull the bottom part of the front grille toward you. (Fig. 1-➀) 2) Lift up and unhook the grille to remove it. (Fig. 1-➁) ➁ ➀ Fig. 1 9-2. Removing Wall Sleeve Wall sleeve (1) While supporting the bottom part of the unit, pull it out of the wall sleeve. (Fig. 2) Unit Fig. 2 9-3. Removing Electrical Component Box Knob (1) Remove knobs and the control panel from the electrical component box.(Fig. 3) Control panel Electrical compornent box Fig. 3 (2) Remove the screws holding the lid of the electrical component box, and also remove the wire clamp holding the lead wires. (Fig. 4) Lid Wire clamp 37 Fig. 4 ➀ (3) Remove the following screws. (Fig. 5) ➀ 2 screws holding the component box ➁ 2 screws holding the ventilator knob ➂ 1 screw holding the power supply cord ➁ ➂ Fig. 5 (4) Disconnect the wiring connectors and lead wires connecting the following electrical parts in the electrical component box.(Fig. 6) • Compressor motor capacitor • Fan motor capacitor Compressor motor capacitor Fan motor capacitor Fig. 6 9-4. Removing Electric Heater Top cover plate (1) Remove the 6 screws holding the top cover plate. (Fig. 7) Fig. 7 (2) Remove the 5 screws holding the blade Ass´y. (Fig. 8) Blade Ass´y 38 Fig. 8 (3) Lift the electrical heater up out of the unit. (Fig. 9) (4) Remove the 4 screws holding the electric heater and take off the evaporator’s casing plate. (Fig. 10) Electric heater Fig. 9 Fig. 10 9-5. Removing Blower Wheel Blower wheel (1) Remove the electric heater. Refer to “9-4. Removing Electric Heater.” (2) Loosen the bolt holding the blower wheel on the motor shaft. (Fig. 11) Fig. 11 (3) Remove the blower wheel from the unit. (Fig. 12) Blower wheel Fig. 12 9-6. Removing Evaporator (1) Remove the top cover plate and blade Ass´y. Refer to “9-4. 1) and 2) Removing Electric Heater.” (2) Remove the screws holding the evaporator. (Fig. 13) Fig. 13 39 Condenser casing 9-7. Removing Condenser (1) Remove the screws holding the condenser casing. (Fig. 14) Fig. 14 (2) Remove the screws holding the condenser. (Fig. 15) (3) Hold the lower part of the condenser with both hands and tilt slightly, then lift up carefully to avoid distorting the copper tube. Condenser Fig. 15 9-8. Removing Propeller Fan (1) Remove the condenser. Refer to “9-7. Removing Condenser.” (2) Loosen the bolt holding the propeller fan on the motor shaft. (Fig. 16) Fig. 16 Condenser Propeller fan (3) Remove the propeller fan from the motor shaft. (Fig. 17) Fig. 17 40 9-9. Removing Fan Motor (1) Remove the condenser. Refer to “9-7. Removing Condenser.” (2) Remove the propeller fan. Refer to “9-8. Removing Propeller Fan.” (3) Remove the 3 screws of the fan motor mounting plate. (Fig. 18) Fan motor 41 Fig. 18 10. FUNCTION 10-1. Room Temperature Control Room temperature control is obtained by cycling the compressor ON and OFF. Cooling Only Model Models STB0810C1 STB1010C1 STB1020C1 STB1220C1 ■ Cooling ● Thermo. ON : When the room temperature rises above T + 4°F (T°F is set temperature). Compressor ➞ ON ● Thermo. OFF : When the room temperature falls below set temperature T°F. Compressor ➞ OFF Room temp. T+4 °F set temp. T °F Compressor Fan motor ON ON OFF Set speed 42 OFF Cooling & Electric Heating Model Models STB0811C1 STB1023C1 STB1123C1 ■ Cooling ● Thermo. ON : When the room temperature rises above T + 4°F (T°F is set temperature). Compressor ➞ ON ● Thermo. OFF : When the room temperature falls below set temperature T°F. Compressor ➞ OFF Room temp. T+4 °F T °F set temp. Compressor ON ON OFF OFF Set speed Fan motor ■ Heating ● Heater ON : When the room temperature falls below T – 4°F (T°F is set temperature). Heater ➞ ON ● Heater OFF : When the room temperature rises above set temperature T°F. Heater ➞ OFF Room temp. set temp. T °F T–4 °F Heater Fan motor ON OFF ON OFF Set speed 43 Heat Pump Model Model STB0823H1 ■ Cooling ● Once the compressor stops, it will not start running again for about 3 minutes. ● Thermo. ON : When the room temperature rises above T + 1°F (T°F is set temperature). Compressor ➞ ON ● Thermo. OFF : When the room temperature falls below set temperature T°F. Compressor ➞ OFF Room temp. set temp. T+1°F T °F 3 minutes or more Compressor ON OFF 3 minutes ON ON OFF ■ Heating (Except during defrosting operation) ● Once the compressor stops, it will not start running again for about 3 minutes. ● Thermo. ON : When the room temperature falls below T°F (T°F is set temperature). Compressor ➞ ON ● Thermo. OFF : When the room temperature rises above T + 1°F. Compressor ➞ OFF ● Changeover to Heater ON : When the room temperature falls below T – 4°F, the unit turns off heat pump operation and electric heater comes on instead of compressor. ● Changeover to Heat pump : When the room temperature rises above T – 3°F, the unit resumes heat pump operation and compressor comes on instead of electric heater. Room temp. set temp. T+1 °F T °F T–3 °F T–4 °F 3 minutes or more Compressor Heater OFF OFF ON OFF ON 3 minutes ON OFF OFF 44 ON 3 minutes ON ON OFF OFF ON OFF OFF 10-2. Defrosting Operation (Heating) Heat Pump Model Model STB0823H1 ■ Defrosting Flowchart Compressor ON Temperature of outdoor heat exchanger coil is blow 14°F. NO YES ● ● Defrosting begins Compressor ➞ OFF Electric Heater ➞ ON Temperature of outdoor heat exchanger coil is higher than 39°F. NO YES Release of defrosting ■ Defrosting Mode Timing Chart Start of defrosting Compressor Electric heater Solenoid coil (4-way valve) Fan motor Release of defrosting ON OFF ON OFF ON OFF ON ON Set speed Outdoor heat 39 °F exch coil temp. 14 °F NOTE Once the air conditioner enters defrosting mode, it will not release defrosting until the outdoor heat exchanger coil temperature rises above 39°F. During this period, heat is provided by electric heater instead of by the heat pump. 45 APPENDIX Control Panel ■ Cooling Only Model Models STB0810C1 STB1010C1 STB1020C1 STB1220C1 THERMOSTAT SELECTOR OFF LOW FAN LOW COOL HIGH FAN HIGH COOL Thermostat Mode selector COOLER ■ Cooling & Electric Heating Model Models STB0811C1 STB1023C1 STB1123C1 THERMOSTAT SELECTOR LOW FAN OFF LOW HEAT HIGH FAN LOW COOL Thermostat WARMER COOLER HIGH HEAT HIGH COOL Mode selector ■ Heat Pump Model Model STB0823H1 THERMOSTAT SELECTOR LOW HEAT HIGH HEAT OFF FAN LOW COOL HIGH COOL Thermostat Mode selector WARMER COOLER 46 Fan Switch The location of Fan Switch differ according to models. When set to CYCLE, fan operation synchronizes with that of compressor's (or heater's) thermo ON and thermo OFF, thereby saving power. When set to CONT, fan continues to operate regardless of thermo ON or thermo OFF condition. Fan switch CYCLE Fan switch FAN CONT CYCLE Cooling Only Model Heat Pump Model Cooling & Electric Heating Model 47 CONT May. / 2001 / 850 Printed in Japan For Parts or Service Contact SANYO HVAC SERVICE CENTER SANYO Fisher Service Company 1165 Allgood Road, Suite 22, Marietta, GA 30062 U.S.A. 300 Applewood Crescent, Concord, Ontario, L4K 5C7, CANADA
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:05:15 18:56:13 Producer : Acrobat Distiller 3.0 for Power Macintosh Modify Date : 2001:05:15 20:43:43 Page Count : 52EXIF Metadata provided by EXIF.tools