Sargent Instructions For Installing 7800 Knob/8200 Lever Mortise Lock 7800Knob8200Lever Escutcheon Rose Trim
User Manual: Sargent Instructions for Installing SARGENT 7800 Knob/8200 Lever Mortise Lock Instruction Sheets
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
SARGENT 8200 Series Mortise Lock Function List 7800/8200 Mortise Locks Multi-function Lockbody Options 04, 05, 06, 13, 31, 36, 37, 38 Instructions for Installing SARGENT 7800 Knob/8200 Lever Mortise Lock U.S. Patent Numbers: 5,678,870; 7,188,870 & 7,452,012 How to Change Function of Lock: Green catch screw must be located as designated on lock case to create desired function. 3 locations: O ne for 05, 37 & 38 functions One for 04, 06, 13 & 31 functions And one for 36 function Note: When moving green catch screw to 04, 06, 13 & 31 functions, hub position must be at 45° as shown on lockcase. 03/F29 Classroom dead lock 04/F07 Storeroom closet lock 05/F04 Office or entry lock 06 Storeroom or service lock 21/F17 Dead lock 22/F16 Dead lock 23 Classroom dead lock 24/F21 Room door lock 30 Dummy trim dead lock 31 Utility lock 35 Storeroom lock 45/F12 Dormitory or exit lock 46/F11 Dormitory or exit lock 59 Double locking 65/F22 Privacy bedroom or bath lock 13/F31 Communicating or exit lock 16/F09 15/F01 Passage or closet Apartment or exit or public toilet latch lock 25/F13 Dormitory or exit lock 26/F14 Store door lock 27 Closet or storeroom lock 36 Closet lock 37/F05 Classroom lock 38/F32 Classroom security intruder latchbolt lock 39/F33 Classroom security intruder deadbolt lock 47/F08/F10 Front door lock or apartment corridor lock 48/F35 Store door lock 49 Security deadbolt 50/51F15 Hotel guest lock/Store room deadbolt lock 52 Institution deadbolt lock 66/F19 Privacy bedroom or bath lock 67/F26 Institutional privacy lock 68/F02 Privacy bedroom or bath lock 70/71 Electrical 70: Fail safe 71: Fail secure 72/73 Electrical 72: Fail safe 73: Fail secure 17/F30 Asylum or institutional lock 20/F18 Dead lock 28 Dummy trim dead lock 29 Dummy trim dead lock Standard 7800/8200 Mortise Lock Sectional Trim Description & Part Number *See How to Change Hand of Lock, page 6. 05 37 38 04 06 13 31 CHECK HUB 36 HUB 89/F06 Hold back lock Items needed to create each of the following functions: Function Outside Lever Inside Lever Trim One Side Kit Outside Cylinder Inside Cylinder 91 90 All purpose hold Classroom back lock security hold back lock 92 All purpose hold back lock 93 Dummy trim Note: Shaded Levers are Rigid at all times Thumb Turn 94 Dummy trim 95 Single trim dummy lock 43/F20 40/41/F34 Apartment Classroom security intruder corridor door lock deadbolt lock 56 Inner entry lock 55/F04 Office or entry lock 76/77* Electrical entry lock (* No cylinder on 77 function 78/79* Electrical entry lock (* No cylinder on 79 function 96 Double trim dummy lock 97 Active trim dummy lock Outside Lever & Rose Assembly (“LN” Rose with “L” Lever) NOTE: 05 FUNCTION HAS A THUMB TURN ON THE INSIDE FACE OF DOOR AND 55 FUNCTION HAS TOGGLE ON LOCK FRONT How To Change Hand of Lock If shaded, knob or 04 X X X 05 X X X lever rigid at all times Note: Red surface of locking piece must face Note: Beveled surface of latch must face secure side of door. strike. The deadlatch is self adjusting. To change hand of latch: To rotate locking piece: X*** X 1. Position lockbody with red surface of locking piece visible X X X X 2. Insert blade type screwdriver into locking piece slot to rotate locking piece 3. Push locking piece toward back of lock body and rotate 180° until RED surface shows on opposite side 06 X X 13 X X 31 X 36 X 37 X X X 38 X X X Note: 04, 06, 13 and 31 Functions require: (a) Green catch screw to be removed (b) Rotate hub to 45 degree position (c) Rotate locking piece for required hand (d) Red surface faces locked side of door (e) R otate hub to the original 45 degree position as shown on lockcase (f) Green catch screw is then reinstalled X *** 130 KB thumb turn is used with rose trim only, escutcheon trims requiring thumb turns, must be preassembled at the factory #41 Cylinder is standard for both single & double cylinder functions for 1-3/4” thick door 1. Insert screwdriver blade into the spade shaped slot Lock front Latch 2. R otate screwdriver 90º to push latch out until back of latch clears lock front. Then rotate latch 180º. Latch will then re-enter lockbody. NOTE: Trim-one-side functions always require an inside trim assembly which can be used on the inside or outside of the door (to order Trim one-side kit (for all trim except PT or FE) order part # 82-4611. (Note: Latch can not be unscrewed) DOOR HANDING INSIDE LEFT HAND RIGHT HAND OUTSIDE Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. 5 Locking piece slot LEFT HAND REVERSE BEVEL Red color indicates locked side of door or hold back side (91 and 92 Functions) INSIDE OUTSIDE RIGHT HAND REVERSE BEVEL DOOR HANDS DETERMINED FROM OUTSIDE 6 Installation for levers and knobs is identical 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 16 17 18 19 20 21 22 Part No. Description Varies ———– 81-0093 01-1495 82-3088 82-0368 82-0184 01-0079 82-3082 81-0723 ———– 77-3279 77-2595 77-0551 01-4370 01-1491 01-1154 77-0509 13-0140 82-0612 Varies Varies 01-1028 Inside lever handle - Consult factory Handle set screw 1/4-28 UNF Rose - “LN” design Machine screw #8-32 x 5/8” Inside adapter & plate assembly Spindle Cap nut Washer Adapter & plate assembly (LN design) Mounting post Outside lever handle - Consult factory Turn lever assembly - 130KB design Emergency button assembly-184KB Backplate Machine screw #6-32 x 3/8” Wood screw #6 x 3/8” Machine screw #6-32 x 1/4” KB cylinder rosette (for 8200) Compression spring Non-loosening wave spring Lockbody Outside Front Machine Screw #8-32 x 1/4” Tools Required: • Phillips screwdriver (standard size) • 1/8” Allen wrench • Phillips & flat tip screwdriver Req. 1 1 2 2 1 2 1 2 1 2 1 1 1 2 4 4 2 2 1 1 2 A7772:F 1 Installation Instructions for 7800/8200 Series Mortise Locks (Except PT Trim and FE Trim) See particular trim section for your lock Inside of door ** Note: LE3 and KE3 are designed for Concealed Cylinders, Concealed Cylinders are installed prior to attaching the Escutcheons. Outside of door (1) Important: Check template A7057 to prep door for function holes, size & location. Verify strike location according to template. Clean door pocket and verify hand of lock Instructions for WT Escutcheon Instructions for TE, CE, LE1, KE1, LE3, KE3, LW1 and KW1 Escutcheon I (2) Slide lock in door Inside of door (3) Slide outside lever & rose assembly (or lever & escutcheon assembly) through the door and lock body Note: Cylinder collar(s) are required for functions with two cylinder and cylinders longer than # 41 (1-1/8”) M Inside of door Note: Cylinder collar(s) are required for functions with two cylinder and cylinders longer than # 41 (1-1/8”) Outside of door Outside of door RH Door Shown Note: If installing trim one side, see separate instruction sheet Note: Keep door open while installing lock (4) Slide cylinder (A) through spring (B) & Inside of collar (C) (or escutcheon) and thread D door into lock until cylinder face is flush with D collar (C) (or escutcheon edge). The key slightly pulled out ofD cylinder will help to thread the cylinder G Note: SARGENT logo must be G F E horizontal & on the top portion G of the cylinder F (5) By hand with # 2 Phillips screwdriver, F Escrew tighten cylinder clamp (6) Secure lock in door with two wood screws #12 x 1-1/4” or D machine screws #12-24 x 1/2” (D) (8) Slide adapter & plate D assembly (F) over spindle & secure with two #8-32 screws (G) I (10) Attach inside lever and secure with 1/8” Allen wrench. IVerify Lock is operating correctly H prior to closing door 2 A7772:F C B A The inside & outside escutcheons are surface applied using eight #6 x 3/4” wood screws or eight #6-32 x 3/4” machine screws (item #M) Instructions for LE2, LE4, KE2 and KE4 Escutcheon Instructions for LS & KS Security Escutcheon Note: LE4 and KE4 are designed for Concealed Cylinders: Concealed Cylinders are installed prior to attaching the Escutcheons. J R/C & I/C cylinder cores require Control key(stamped”C”) to install. Must request separately. If 1 bitted - specify 11311 cut. K Inside of door L (12) Check for proper operation (13) A ttach outside front (H) with two #8-32 x 1/4” flat head screws (I) Note: To check for proper lock operation by function number (ex: 8205 = 05 function) - see 7800/8200 catalog (www.sargentlock.com). Note: Cylinder collar(s) are required for functions with two cylinder and cylinders longer than # 41 (1-1/8”) Inside of door Note: The cylinder is installed under the escutcheon. Once the escutcheon is installed, the cylinder should be backed out toward the escutcheon as far as possible. Once positioned correctly, secure cylinder in the lock body. Outside of door J H N Outside of door (11) A ssemble thumbturn/ emergency release according to instructions on bag J H A B A CE B J I C Outside of door Through-bolt the inside escutcheon to the outside escutcheon with two #8-32 x 1-7/8” screws (item #I) Note: Screw heads should be visible on inside escutcheon D (7) Slide spindle (E) into lockbody hub (9) S crew rose (J) firmly onto adapter & plate assembly (F) (or attach escutcheon) Cylinder Clamp Screw The outside escutcheon must be through-bolted with items K & L prior to attaching the inside escutcheon. Position inside escutcheon over item #L and secure with set screws (item #J) using .050” Allen wrench 3 Through-bolt the inside escutcheon to the outside escutcheon with four 1/4-20 x 1-3/8” screws (item #N) Note: Screw heads are visible on inside escutcheon Note: Double cylinder functions use the Cylinder Retaining Cap (supplied). Both cylinders are installed followed by the Cylinder Retaining Cap over each cylinder, then the escutcheons. The cylinders should then be backed out and secured in place. 4 Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.6-c011 79.156289, 2014/03/31-23:39:12 Instance ID : uuid:1c741099-f9be-9e49-9b51-fe9a921e6fac Original Document ID : adobe:docid:indd:b7206997-ef81-11e1-b0b6-85adfdf5f86f Document ID : xmp.id:1c59d11b-188d-4403-a7ef-bf9789e60681 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:f3880e2c-9bf4-45c9-8136-c0d3486bb9ea Derived From Document ID : xmp.did:4b94862b-9a60-4129-9353-29c2b1f22f04 Derived From Original Document ID: adobe:docid:indd:b7206997-ef81-11e1-b0b6-85adfdf5f86f Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2014 (Macintosh) History Changed : / History When : 2014:09:09 13:01:25-04:00 Create Date : 2014:09:09 13:01:25-04:00 Modify Date : 2014:09:09 13:01:32-04:00 Metadata Date : 2014:09:09 13:01:32-04:00 Creator Tool : Adobe InDesign CC 2014 (Macintosh) Format : application/pdf Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CC 2014 (Macintosh)EXIF Metadata provided by EXIF.tools