Sargent 8500 Series Narrow Design Rim Type Exit Device Installation Instructions A6699N

User Manual: Sargent 8500 Series Narrow Design Rim Type Exit Device Installation Instructions Instruction Sheets

Open the PDF directly: View PDF PDF.
Page Count: 4

DownloadSargent 8500 Series Narrow Design Rim Type Exit Device Installation Instructions A6699N
Open PDF In BrowserView PDF
INSTALLATION INSTRUCTIONS
8500 / 12-8500 / AD8500 Narrow Design Rim Exit Device
FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

CAUTION: BEFORE STARTING
• INSTALL MULLION IF USED
• DOOR SHOULD BE FITTED AND HUNG
• CHECK BOX LABEL FOR SIZE OF
EXIT DEVICE FUNCTION AND DESIGN

IMPORTANT: SURFACE OF DOOR WHERE EXIT
DEVICE IS TO BE APPLIED MUST BE FLUSH. CLEAR
AWAY ANY RAISED PROJECTIONS TO ALLOW EXIT
DEVICE TO REST FLAT ON SURFACE OF DOOR.

AVAILABLE STOCK LENGTHS
Length “E": 32" door
Can be cut to fit doors down to 24" wide.
Length “F": 36" door
Can be cut to fit doors down to 33" wide.

MOUNTING
PLATE

END CAP

RAIL
ASSEMBLY

Length “J": 42" door
Can be cut to fit doors down to 37" wide.
Length “G": 48" door
Can be cut to fit doors down to 43" wide.
VERTICAL REFERENCE
LINE (C CHASSIS)
L
STRIKE
#657
SHOWN

LOCK DOWN KEY
TO OPERATE:
— DEPRESS PUSH RAIL;
— INSERT HEX KEY AND
TURN CLOCKWISE

CHASSIS

ARM
HORIZONTAL
REFERENCE LINE
(C
L CHASSIS AND
RAIL ASSEMBLY)

1

COVER
650A MULLION WITH 658 FLAT
STRIKE (ALTERNATE STRIKE)

APPLY STRIKE TO FRAME
OR MULLION

Surface applied 649 strike, 12-8500, AD8500, or
optional standard application
INTEGRAL STOP
657 STRIKE

ATTACH WITH SCREWS
PROVIDED. FURNISHED
WITH 650A MULLIONS

SURFACE APPLIED 657 STRIKE
(STANDARD STRIKE)

ATTACH WITH (2) STRIKE SCREWS
AND USE (2) LOCK WASHERS
BETWEEN FRAME AND STRIKE

BLADE STOP
657 STRIKE

DRILL AND COUNTERSINK FOR 1/4"
FLAT HEAD SCREWS

L980 MULLION
656 STRIKE

ALUMINUM FRAMES: DRILL (2) 3/8" HOLES FOR
MOLLY-JACK NUTS. REINFORCED METAL FRAMES:
DRILL AND TAP (2) 10-24 HOLES
DRILL (2) 3/8"
HOLES FOR
MOLLY-JACK NUTS

DRILL (2) 3/8"
HOLES FOR
MOLLY-JACK NUTS

Copyright © 2009-2012, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

A6699N

1

2

MARK VERTICAL AND HORIZONTAL
REFERENCE LINES ON DOOR

13/16" FROM
SURFACE OF STRIKE
(REFERENCE STRIKE
TEMPLATE)

3

PREPARE DOOR
TAPE TEMPLATE ON INSIDE OF DOOR ALONG
REFERENCE LINES. SPOT AND DRILL HOLES.
MORTISE HOLES FOR OUTSIDE TRIM, IF
REQUIRED.

41" FROM FINISHED
FLOOR, OR AS
SPECIFIED

HORIZONTAL
REFERENCE LINE (C LOF
STRIKE AND LATCHBOLT
HOLE LOCATION
(EXAMPLE)

41" FROM FINISHED
FLOOR, OR AS
SPECIFIED

4

TAPE
SUPPLIED

VERTICAL REFERENCE
LINE (CL OF CHASSIS)

8500 / 12-8500
04, 44, 10, 40 FUNCTIONS

CYLINDER
ADAPTER

8500 / 12-8500
13, 15, 43, 73, 74 Functions

Trim cylinder tail for 1/4" to
1/2" projection thru door,
04 / 44 functions.

Using vertical and horizontal
reference lines, attach trim,
outside door surface.

Install cylinder adapter on
cylinder BEFORE installing
cylinder in door.

Thru-bolt chassis to trim,
inside door surface, top and
bottom, as shown.

10/40 functions: same except
no cylinder.

#34 RIM
CYLINDER

8513 SHOWN

8504 SHOWN

2

Copyright © 2009-2012, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

A6699N

NOTE:
CHASSIS SCREWS REQUIRED,
12-FIRE RATED DEVICES, AS SHOWN.
(2) #10-24 x 1 1/4" PH #8 OV. HD. Machine Screws

5

APPLY HARDWARE

A DETERMINE CUT OFF DIMENSION “X" BY

SUBTRACTING 1-1/8" FROM DIMENSION “Y".
MARK CUT OFF POINT ON MOUNTING RAIL.
• CHECK BOX LABEL. 			
IF CUTTING IS NOT REQUIRED,
PROCEED TO STEP “B".
• IF CUTTING IS REQUIRED, 		
CONTINUE WITH STEP “A".

FOR DOOR
WITH STILE
RAIL, MUST
OVERLAP
STILE BY 5/16"

VERTICAL REFERENCE
LINE (CL OF CHASSIS)

1-1/8" MIN.

X
Y

PUSH
RAIL
CAUTION
DO NOT CUT CLOSER THAN 3-1/2" FROM
THE PIVOT PIN IN THE PUSH RAIL

B

3-1/2"
MIN.

B DEPRESS ARM INTO RAIL OPENING AND
SLIDE RAIL ONTO CHASSIS. LEVEL RAIL
AND FASTEN MOUNTING PLATE.
LEVEL
MOUNTING
PLATE

TIGHT AGAINST
MOUNTING RAIL

ATTACH MOUNTING PLATE
TO DOOR WITH
(2) ROUND HEAD SCREWS

Copyright © 2009-2012, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

A6699N

3

6

(-53) LATCH BOLT MONITERING
ADJUSTMENT

Note: The latch bolt switch will come pre-set for the most
common applications. If the sensitivity needs to be adjusted,
follow the steps below.
1. Loosen screw and nut
2. R
 otate switch
(up for quicker
reaction or down for
slower reaction).
3. Tighten screw and nut
4. Check operation
5. Install chassis cover

7

ATTACH END CAP TO
MOUNTING PLATE WITH (2)
COVER SCREWS
ATTACH COVER THRU RAIL INTO CHASSIS
WITH (2) #8-32 TRUSS HEAD SCREWS
ATTACH COVER TO
CHASSIS WITH (2)
COVER SCREWS

NOTE: Make sure switch is located on the mounting post and
the screw and nut are securely fastened
Using your mobile phone,
scan this Microsoft® Tag.
Download the free mobile app
at http://gettag.mobi

SCREW PACKS AND MISCELLANEOUS PARTS

4

Copyright © 2009-2012, Sargent Manufacturing Company,
an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

A6699N

APPLY COVERS
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00
Instance ID                     : uuid:f9a7f2e8-f1b3-c744-ac46-3a5848fb219e
Document ID                     : adobe:docid:indd:7a2add94-4a59-11e1-aed2-a42f25295b6c
Original Document ID            : adobe:docid:indd:7a2add94-4a59-11e1-aed2-a42f25295b6c
Rendition Class                 : proof:pdf
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:66D31674072068118C14989FBE1DCDAC, xmp.iid:67D31674072068118C14989FBE1DCDAC, xmp.iid:DBCCC31F0E2068118A6DAE099A16B3D6, xmp.iid:80AA31B70E2068118A6DAE099A16B3D6, xmp.iid:B9B094BA0F2068118A6DAE099A16B3D6, xmp.iid:3EB53D27372068118C14F9921864C2E1, xmp.iid:3FB53D27372068118C14F9921864C2E1, xmp.iid:62711B270E2068118C1496A199313631, xmp.iid:83CC4D3D0E2068118C1496A199313631, xmp.iid:10681DD6122068118C1496A199313631, xmp.iid:56F7D8AA132068118C1496A199313631, xmp.iid:4B9183A6252068118C1496A199313631, xmp.iid:C5F2A2B2252068118C1496A199313631, xmp.iid:A13D64222A2068118C1496A199313631, xmp.iid:035F6C342A2068118C1496A199313631, xmp.iid:8DE71E0F212068118C148816D73C9DD7
History When                    : 2012:01:27 09:23:05-05:00, 2012:01:27 09:23:05-05:00, 2012:02:03 13:31:26-05:00, 2012:02:03 13:35:40-05:00, 2012:02:03 13:42:55-05:00, 2012:02:08 15:22:03-05:00, 2012:02:08 15:27:35-05:00, 2012:02:15 10:16:37-05:00, 2012:02:15 10:17:14-05:00, 2012:02:15 10:50:09-05:00, 2012:02:15 10:56:06-05:00, 2012:02:15 13:04:49-05:00, 2012:02:15 13:05:09-05:00, 2012:02:15 13:36:55-05:00, 2012:02:15 13:37:25-05:00, 2012:02:17 13:32:18-05:00
History Software Agent          : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata
Create Date                     : 2012:02:27 16:23:20-05:00
Modify Date                     : 2012:02:27 16:23:23-05:00
Metadata Date                   : 2012:02:27 16:23:23-05:00
Creator Tool                    : Adobe InDesign CS5 (7.0)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 11461 bytes, use -b option to extract), (Binary data 11628 bytes, use -b option to extract)
Doc Change Count                : 44
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 4
Creator                         : Adobe InDesign CS5 (7.0)
EXIF Metadata provided by EXIF.tools

Navigation menu