Sargent 8500 Series Narrow Design Rim Type Exit Device Installation Instructions A6699N

User Manual: Sargent 8500 Series Narrow Design Rim Type Exit Device Installation Instructions Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 4

1

CAUTION: BEFORE STARTING

• INSTALL MULLION IF USED

• DOOR SHOULD BE FITTED AND HUNG

• CHECK BOX LABEL FOR SIZE OF

EXIT DEVICE FUNCTION AND DESIGN

AVAILABLE STOCK LENGTHS

Length “E": 32" door

Can be cut to fit doors down to 24" wide.

Length “F": 36" door

Can be cut to fit doors down to 33" wide.

Length “J": 42" door

Can be cut to fit doors down to 37" wide.

Length “G": 48" door

Can be cut to fit doors down to 43" wide.

1

IMPORTANT: SURFACE OF DOOR WHERE EXIT

DEVICE IS TO BE APPLIED MUST BE FLUSH. CLEAR

AWAY ANY RAISED PROJECTIONS TO ALLOW EXIT

DEVICE TO REST FLAT ON SURFACE OF DOOR.

APPLY STRIKE TO FRAME

OR MULLION

650A MULLION WITH 658 FLAT

STRIKE (ALTERNATE STRIKE)

SURFACE APPLIED 649 STRIKE, 12-8500, AD8500, OR

OPTIONAL STANDARD APPLICATION

INTEGRAL STOP

657 STRIKE

SURFACE APPLIED 657 STRIKE

(STANDARD STRIKE)

BLADE STOP

657 STRIKE

ATTACH WITH SCREWS

PROVIDED. FURNISHED

WITH 650A MULLIONS

ATTACH WITH (2) STRIKE SCREWS

AND USE (2) LOCK WASHERS

BETWEEN FRAME AND STRIKE

DRILL AND COUNTERSINK FOR 1/4"

FLAT HEAD SCREWS

ALUMINUM FRAMES: DRILL (2) 3/8" HOLES FOR

MOLLY-JACK NUTS. REINFORCED METAL FRAMES:

DRILL AND TAP (2) 10-24 HOLES

DRILL (2) 3/8"

HOLES FOR

MOLLY-JACK NUTS

INSTALLATION INSTRUCTIONS

8500 / 12-8500 / AD8500 Narrow Design Rim Exit Device

FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

Copyright © 2009-2012, Sargent Manufacturing Company,

an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A6699N

STRIKE

#657

SHOWN

HORIZONTAL

REFERENCE LINE

(C CHASSIS AND

RAIL ASSEMBLY)

LCOVER

ARM

CHASSIS

VERTICAL REFERENCE

LINE (C CHASSIS)

L

RAIL

ASSEMBLY

MOUNTING

PLATE END CAP

LOCK DOWN KEY

TO OPERATE:

— DEPRESS PUSH RAIL;

— INSERT HEX KEY AND

TURN CLOCKWISE

DRILL (2) 3/8"

HOLES FOR

MOLLY-JACK NUTS

L980 MULLION

656 STRIKE

2

3

4

2MARK VERTICAL AND HORIZONTAL

REFERENCE LINES ON DOOR

41" FROM FINISHED

FLOOR, OR AS

SPECIFIED

TAPE TEMPLATE ON INSIDE OF DOOR ALONG

REFERENCE LINES. SPOT AND DRILL HOLES.

MORTISE HOLES FOR OUTSIDE TRIM, IF

REQUIRED.

PREPARE DOOR

41" FROM FINISHED

FLOOR, OR AS

SPECIFIED

TAPE

SUPPLIED

HORIZONTAL

REFERENCE LINE (C OF

STRIKE AND LATCHBOLT

L

HOLE LOCATION

(EXAMPLE)

VERTICAL REFERENCE

LINE (C OF CHASSIS)

L

8500 / 12-8500

04, 44, 10, 40 FUNCTIONS

TRIM CYLINDER TAIL FOR 1/4" TO

1/2" PROJECTION THRU DOOR,

04 / 44 FUNCTIONS.

INSTALL CYLINDER ADAPTER ON

CYLINDER BEFORE INSTALLING

CYLINDER IN DOOR.

10/40 FUNCTIONS: SAME EXCEPT

NO CYLINDER.

8500 / 12-8500

13, 15, 43, 73, 74 Functions

USING VERTICAL AND HORIZONTAL

REFERENCE LINES, ATTACH TRIM,

OUTSIDE DOOR SURFACE.

THRU-BOLT CHASSIS TO TRIM,

INSIDE DOOR SURFACE, TOP AND

BOTTOM, AS SHOWN.

8504 SHOWN

Copyright © 2009-2012, Sargent Manufacturing Company,

an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A6699N

13/16" FROM

SURFACE OF STRIKE

(REFERENCE STRIKE

TEMPLATE)

CYLINDER

ADAPTER

#34 RIM

CYLINDER

8513 SHOWN

NOTE:

CHASSIS SCREWS REQUIRED,

12-FIRE RATED DEVICES, AS SHOWN.

(2) #10-24 x 1 1/4" PH #8 OV. HD. MACHINE SCREWS

3

5APPLY HARDWARE

DETERMINE CUT OFF DIMENSION “X" BY

SUBTRACTING 1-1/8" FROM DIMENSION “Y".

MARK CUT OFF POINT ON MOUNTING RAIL.

A

X

Y

VERTICAL REFERENCE

LINE (C OF CHASSIS)

L

FOR DOOR

WITH STILE

RAIL, MUST

OVERLAP

STILE BY 5/16"

1-1/8" MIN.

PUSH

RAIL

3-1/2"

MIN.

CAUTION

DO NOT CUT CLOSER THAN 3-1/2" FROM

THE PIVOT PIN IN THE PUSH RAIL

X

Y

• CHECK BOX LABEL.

IF CUTTING IS NOT REQUIRED,

PROCEED TO STEP “B".

• IF CUTTING IS REQUIRED,

CONTINUE WITH STEP “A".

B

DEPRESS ARM INTO RAIL OPENING AND

SLIDE RAIL ONTO CHASSIS. LEVEL RAIL

AND FASTEN MOUNTING PLATE.

B

LEVEL

MOUNTING

PLATE

ATTACH MOUNTING PLATE

TO DOOR WITH

(2) ROUND HEAD SCREWS

TIGHT AGAINST

MOUNTING RAIL

Copyright © 2009-2012, Sargent Manufacturing Company,

an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A6699N

4

76 APPLY COVERS(-53) LATCH BOLT MONITERING

ADJUSTMENT

ATTACH END CAP TO

MOUNTING PLATE WITH (2)

COVER SCREWS

SCREW PACKS AND MISCELLANEOUS PARTS

Copyright © 2009-2012, Sargent Manufacturing Company,

an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A6699N

ATTACH COVER THRU RAIL INTO CHASSIS

WITH (2) #8-32 TRUSS HEAD SCREWS

Note: The latch bolt switch will come pre-set for the most

common applications. If the sensitivity needs to be adjusted,

follow the steps below.

1. Loosen screw and nut

2. Rotate switch

(up for quicker

reaction or down for

slower reaction).

3. Tighten screw and nut

4. Check operation

5. Install chassis cover

NOTE: Make sure switch is located on the mounting post and

the screw and nut are securely fastened

ATTACH COVER TO

CHASSIS WITH (2)

COVER SCREWS

Using your mobile phone,

scan this Microsoft® Tag.

Download the free mobile app

at http://gettag.mobi