Sargent A6761C Installation Instructions For 10G70 & 10G71 Electro Mechanical Bored Lock 1 3/4 Door With Elect
User Manual: Sargent Installation Instructions for 10G70 & 10G71 Electro-Mechanical Bored Lock for 1 3/4 door With Elect Instruction Sheets
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
1-1/8 " LOCKSET 10 Line 23-10 Line 25-10 Line 13/16" (Typ.) 2-9/16" Ref. 3/8" dia. Raceway 2 Refer to page 2 for wiring instructions. All connections should be insulated. 5/16" dia. (2 Places) 2-1/8" dia. 1 5/16" (Typ.) See electric hinge manufacturers' template for mortise detail TEMPLET NO. 4409-1 B 16-APR-04 RELEASE DATE As part of their promise to provide innovative, fast and effective, and higher security solutions to their customers, ASSA ABLOY Group companies offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx® is a registered trademark of ASSA ABLOY, Inc. ElectroLynx® 10-Line bored-in lock door manufacturer template for solenoid functions (2-3/4", 3-3/4" & 5" backsets) Lock Raceway harness ElectroLynx Connector system Provide pocket clearance (approx. 1"x1") for ElectroLynx connector system (8-pin & 4-pin connectors) Door with raceway Pigtail Hinge 1. Always make provision(s) to protect electrical wires from abrasion 2. Minimum 3/4" dia. raceway to connect from upper corner of reinforcement to hinge pocket Note: Field modifications to doors may alter U.L. listed fire rating. Inside/outside of door 5/32" 2-15/32" Backset (see chart) 1 Power requirement: 12V AC/DC, 0.50 amps or 24V AC/DC, 0.25 amps Prep directions: Over-drill 1" dia. to a depth of 2-9/16" beyond backset to create pocket for ElectroLynx connectors 1 " Ref. Backset: See chart Wood door applications Lock edge of door Metal door: Prep for #8-32 unc machine screws 1" dia. 2-1/4" BACKSET 2-3/4" 3-3/4" 5" INSTALLATION INSTRUCTIONS FOR 10G70 & 10G71 Electro-Mechanical Bored Locks for 1-3/4" Doors With ElectroLynx® Connector System For installation assistance, contact SARGENT at 800-810-WIRE(9473) or www.sargentlock.com © SARGENT Manufacturing Company All rights reserved A6761C • • • • • • • Installation Notes: 10G70, 10G71, RX-10G70, RX-10G71 Lockbodies are available with either 12V or 24V solenoid Solenoids require either 12V or 24V AC transformer or a filtered and regulated power supply Lockbodies have an in-line bridge rectifier RX- Lockbodies are handed (RH, RHR, LH, LHR) Doors manufactured by ASSA ABLOY Group Companies are available pre-wired with ElectroLynx Doors without ElectroLynx will have to be hard wired 10 Line solenoids are not polarity sensitive Red (+), 2 Installation and wiring instructions Wire colors remain consistent with all ASSA ABLOY products Black (-), 1 8 7 8 7 6 4 5 3 2 1 6 4 5 3 These plug into each other 1. While installing the lock into the door, plug the lock's 8-Pin connector into the door's wire harness 2. Wire the Pigtail Harness to transformer or power supply 3. Verify correct voltage is being used Pigtail Harness (QC2 Shown) 2 wire with 8-pin connector) 2 1 Black (-) Red (+) Wh ite Green Orange Blue Brown Yellow CAUTION: The AC/DC voltage must not exceed 13.2 VOLTS FOR 12V LOCKS AND 26.4V for 24V locks. If voltage exceeds this value, the lock solenoid may be damaged. 4. Plug Pigtail Harness 8-pin connector into electric hinge 8-pin connector 5. Test lock: Applying voltage unlocks fail secure lock and locks fail safe lock 10G70 or 10G71 lock with 8-pin connector. Lock is not polarity sensitive. Red, 2 Black, 1 8-wire QC8 Electric Hinge with 8-pin connectors Door harness with 8 & 4 pin connectors The 4 pin connectors are not used in this application Note: Typical door harness location is shown. Other locations may exist depending on door type. Sample wiring 10G70 Series Solenoid Locks with a 12VDC or 24VDC Regulated and Filtered Power Supply. SARGENT offers both power supplies in 12VDC and 24VDC. 12VDC OR 24VDC Regulated and Filtered Power Supply Normally Closed Fire Alarm Contact (If Required) Red (+), 2 NC C * Black (-), 1 Switch or relay contacts Input +- +- L N 120VAC 60HZ Pigtail Harness (2 wires with 8-pin connector) NO GND Output 1 Output 2 120VAC L/N/G * Note: Wire 10G70 (Fail Safe) Locks to switch as shown For 10G71 (Fail Secure) Locks, wire the switch with a normally open contact to the red wire of the Pigtail Harness 8 7 6 4 5 3 2 1 Plug into 8-pin hinge connector at door Wiring for RX-10G70/71 Series Solenoid locks. The lock is either 12VAC / VDC or a 24VAC / VDC lock body. C PIN 3 WHITE NO PIN 4 GREEN NC PIN 5 ORANGE RX SWITCH- MONITORS INSIDE HANDLE (HANDED) 8 6 4 2 7 5 3 1 GE ORAN WHITE GREEN (+) PIN 2 RED LOCK BODY NC C NO RX SWITCH + (-) PIN 1 BLACK POWER 12VAC / VDC or a 24VAC / VDC Lockbody IN LINE BRIDGE RECTIFIER SOLENOID © SARGENT Manufacturing Company All rights reserved A6761C
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:d2886e88-73a5-4c3b-9156-7669d6f49c1d Producer : Acrobat Distiller 6.0.1 for Macintosh Modify Date : 2007:08:21 08:09:01-04:00 Creator Tool : QuarkXPress: pictwpstops filter 1.0 Create Date : 2007:08:20 08:35:20-04:00 Metadata Date : 2007:08:21 08:09:01-04:00 Document ID : uuid:d2a28a66-4f19-11dc-b096-000a957d8766 Format : application/pdf Creator : atobin Title : A6761C Author : atobinEXIF Metadata provided by EXIF.tools