Sargent 55 Signal Switch For 80 Series Installation Instructions A6808C
User Manual: Sargent 55- Signal Switch for 80 Series Installation Instructions Instruction Sheets
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Installation and Wiring Instructions for the 55- and 12-55- Prefix (Signal Switch) 80 Series Exit Device to ElectroLynx™ Connector System For assistance, contact SARGENT at 800-810-WIRE (9473) or www.sargentlock.com A. Function The 55- prefix signal switch monitors the touch bar. When the rail is depressed or dogged, the switch is de-activated. B. Important 1. Caution: Disconnect all input power before beginning installation to prevent electrical shock and equipment damage. 2. Installer must be a trained, experienced service person. 3. All wiring must comply with applicable local electrical codes, ordinances and regulations. 55- or 12-5580 Series Rail with 8-pin connector 8 7 6 4 5 3 2 1 Blue (C), 55Brown (NO), 55Yellow (NC), 55- C. ElectroLynx Connector System Notes: The system is designed to be installation friendly with quick connectors from the electric hinge through the door to the rail. The only wiring required is to the loose wires on the pigtail harness assembly on the frame side of the electric hinge. Locking mechanism Plug Receptacle IMPORTANT: The plug and receptacle connectors are designed to mate and lock together as shown in the figure. Plug the connectors into each other with the locking mechanism aligned as indicated. Do NOT force connectors on any other way. Copyright © SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited. A6808C D. Installation Notes 1. With new applications, a raceway harness with 8 and 4 pin connectors will be pre-installed inside door by ASSA ABLOY door manufacturer when specified during the ordering process. Raceway harness kits are also available for retrofit applications. 2. If door does not have a raceway harness with connectors, cut connectors off product, or consult factory for raceway retrofit kit. 3. Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail connector terminations and wire colors all match. E. 55- 80 Series (Signal Switch) Installation and Wiring 55Switch Connections mounting bracket Electric Hinge with 8-pin connectors Yellow (NC), 8 screw location 1" dia hole in door Brown (NO), 7 Blue (C), 6 8 7 6 4 5 3 Pigtail harness with 8-pin connector 2 1 1 4 3 NOTES: 1. 2. 3. 4. 5. Raceway harness with 8 & 4 pin connectors. The 4-pin connectors are not used. Switch contact rating: 2A @ 30VDC Wires must be protected from abrasion For use with class II circuits only Wiring diagram indicates push bar extended The rail, raceway, electric hinge and pigtail connector terminations and wire colors all match 2 55- or 12-5580 Series Rail with 8-pin connector Note: Typical raceway location is shown. Other locations may exist depending on door type. 1 Mount exit device per instruction sheet provided To insure trouble free operation, check that the push rail can be fully depressed. On vertical rod exit devices, check that the latch bolts do not go into hold back position until the push rail is fully depressed. 2 Plug rail connector into raceway connector. Then feed through 1" hole in door. Install rail mounting bracket with two screws supplied. Install rail insert and end cap. 3 Plug raceway connector into electric hinge connector, then feed through door prep. Mount electric hinge to door. 4 Go to (A) if wiring now. Go to (B) if wiring is to be done later. A. Wire frame side wires to wires on pigtail harness as required using connectors allowed by local code. Plug pigtail harness connector into electric hinge connector. Feed harnesses through frame prep and mount electric hinge. B. Plug pigtail harness connector into electric hinge connector. Feed harnesses through frame prep and mount electric hinge. Copyright © SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited. A6808C
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 2 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Creator : QuarkXPress(R) 7.31 Modify Date : 2008:05:08 15:25:37 Create Date : 2008:05:08 15:25:37 Producer : QuarkXPress(R) 7.31 Title : Layout 1EXIF Metadata provided by EXIF.tools