Sargent 55 Signal Switch For 80 Series Installation Instructions A6808C

User Manual: Sargent 55- Signal Switch for 80 Series Installation Instructions Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 2

A. Function

The 55- prefix signal switch monitors the touch bar. When the rail is depressed or dogged, the switch is de-activated.

B. Important

1. Caution: Disconnect all input power before beginning installation to prevent electrical shock and

equipment damage.

2. Installer must be a trained, experienced service person.

3. All wiring must comply with applicable local electrical codes, ordinances and regulations.

C. ElectroLynx Connector System Notes:

The system is designed to be installation friendly with quick

connectors from the electric hinge through the door to the

rail. The only wiring required is to the loose wires on the

pigtail harness assembly on the frame side of the electric

hinge.

IMPORTANT:

The plug and receptacle connectors are designed to mate

and lock together as shown in the figure. Plug the

connectors into each other with the locking mechanism

aligned as indicated.

Do NOT force connectors on any other way.

55- or 12-55-

80 Series Rail with 8-pin connector

Brown (NO), 55-

Yellow (NC), 55-

Blue (C), 55-

1

75

64

3

2

8

Plug

Locking mechanism

Receptacle

Installation and Wiring Instructions for the

55- and 12-55- Prefix (Signal Switch) 80 Series

Exit Device to ElectroLynx™ Connector System

For assistance, contact SARGENT at 800-810-WIRE (9473) or www.sargentlock.com

A6808C

Copyright ©SARGENT Manufacturing. All rights reserved.

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

D. Installation Notes

1. With new applications, a raceway harness with 8 and 4 pin connectors will be pre-installed inside door by

ASSA ABLOY door manufacturer when specified during the ordering process. Raceway harness kits are also

available for retrofit applications.

2. If door does not have a raceway harness with connectors, cut connectors off product, or consult factory for

raceway retrofit kit.

3. Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail connector

terminations and wire colors all match.

Mount exit device per instruction sheet provided

To insure trouble free operation, check that the push rail can be fully depressed. On vertical rod exit

devices, check that the latch bolts do not go into hold back position until the push rail is fully depressed.

Plug rail connector into raceway connector. Then feed through 1" hole in door. Install rail mounting bracket with two screws

supplied. Install rail insert and end cap.

Plug raceway connector into electric hinge connector, then feed through door prep. Mount electric hinge to door.

Go to (A) if wiring now. Go to (B) if wiring is to be done later.

A. Wire frame side wires to wires on pigtail harness as required using connectors allowed by local

code. Plug pigtail harness connector into electric hinge connector. Feed harnesses through frame prep

and mount electric hinge.

B. Plug pigtail harness connector into electric hinge connector. Feed harnesses through frame prep and mount

electric hinge.

1

2

3

4

E. 55- 80 Series (Signal Switch) Installation and Wiring

NOTES:

1. Switch contact rating: 2A @ 30VDC

2. Wires must be protected from abrasion

3. For use with class II circuits only

4. Wiring diagram indicates push bar extended

5. The rail, raceway, electric hinge and pigtail

connector terminations and wire colors all match

Pigtail harness

with 8-pin connector

Raceway harness with

8 & 4 pin connectors.

The 4-pin connectors

are not used.

Electric Hinge

with 8-pin connectors

Note: Typical raceway location is

shown. Other locations may exist

depending on door type.

4

55- or 12-55-

80 Series Rail with

8-pin connector

1

75

64

3

2

8

Brown (NO), 7

Yellow (NC), 8

Blue (C), 6

55-

Switch

Connections

1

32

mounting

bracket

1" dia

hole

in door

screw

location

Copyright ©SARGENT Manufacturing. All rights reserved.

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

A6808C