Sargent 1431 Door Closer With UO/O/RO/O8/OLC/P9/RP9/P3/P3A/P4/P4A/Z/OZA Standard Duty Arms (Without Hold Ope A7139K

User Manual: Sargent 1431 Door Closer With UO/O/RO/O8/OLC/P9/RP9/P3/P3A/P4/P4A/Z/OZA Standard Duty Arms (Without Hold Ope Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 8

A7139K - 11/01/11

without the express written permission of Sargent Manufacturing Company is prohibited.

1431 DOOR CLOSER WITH STANDARD DUTY ARMS

(WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS

1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6

FOR INSTALLATION ASSISTANCE, CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

Standard Mounting Application with

0, R0, 08 or 0LC Arm

For Standard Applications – Door is mounted on the hinge side

of the door (see page 2)

Parallel Arm Application with

P9, RP9, P3, P3A, P4 or P4A Arm

For Parallel Arm Applications – Door Closer is mounted on the

top side of the door (see page 4)

Top Jamb Application with

0, R0, 0Z or 0ZA Arm

For Top Jamb Application – Door Closer is mounted on the

frame on the stop side of the door (see page 6)

without the express written permission of Sargent Manufacturing Company is prohibited.

11/01/11

A7139K

• Select closer mounting position based on the maximum door opening, as listed below

Note: For ADA applications, select the 160º position.

STANDARD APPLICATION

• Using the enclosed self adhesive template, locate and mark hole locations

Note: 3/32" pilot holes are required when Self Tapping Screws are being used

If machine screws are being used, use a drill #16 (.177) and a #12-24 tap

• Install closer body onto the door with 5/8" power adjustment nut end away from hinge

• Install foot & rod assembly onto the frames

** If butt, frame and wall conditions permit,

door will open 180º

Note: On the foot & rod assembly always

use the pivot farthest from the hinge

RIGHT HAND DOOR ILLUSTRATED, SAME DIMENSIONS APPLY FOR LEFT HAND DOOR.

*SEE PAGE 8 FOR MORTISE NUTS

• Install main arm on the closer with the index mark on the spindle aligning with #2 on the main arm (as shown)

STANDARD APPLICATION

• Opening the door slightly, slide rod into swivel arms and then close the door

• With the door closed, position the swivel arm so it is 90º to the door surface

• Tighten the arm screw securely

Adjust closer as required (See page 8 for details)

ACCESSORY INFORMATION

08 Mortise foot may be

used when the standard

surface applied foot

cannot be attached to

the top casing or where

appearance is a major

factor

Mortise Foot

1431-J Cover Plate

May be used when closer is mounted on a narrow

rail to improve appearance when closer is viewed

through glass

1431-W Corner bracket

May be used for exterior doors to keep the closer inside of building;

also to obtain full 180º door opening closer is mounted on bracket

attached to door jamb on stop side of door

Mortise nuts for bolting through the door are furnished when ordered

A7139K - 11/01/11

without the express written permission of Sargent Manufacturing Company is prohibited.

11/01/11

A7139K

• Select closer mounting position based on the maximum door opening, as listed below

Note: For ADA applications, select the 180º position.

PARALLEL APPLICATION

• Using the enclosed self adhesive template, locate and mark hole locations

Note: 3/32" pilot holes are required when Self Tapping Screws are being used

If machine screws are being used, use a drill #16 (.177) and a #12-24 tap

• Install closer body onto the door with 5/8" power adjustment nut end towards hinge

• Install foot bracket & rod assembly onto the frames

Note: P9 or RP9 arm shown.

For P3, P3A, P4,P4A arms,

use data sheet enclosed

LEFT HAND DOOR SHOWN

SAME DIMENSIONS APPLY FOR RIGHT HAND DOOR *SEE PAGE 8 FOR MORTISE NUTS

INSTRUCTIONS FOR INSTALLING PARALLEL ARM APPLICATION

Closer mounted on stop side of door

• Install main arm on the closer with index mark on spindle aligned with the number on the arm

Note: Left Hand Doors – align index mark with the #4 on the main arm (as shown)

Right hand Door – align index mark with the #5 on the main arm (as shown)

• This requires the spindle to be rotated

• Rotate the spindle on the bottom of the closer to align index mark and the required number on the arm

• Opening the door slightly, slide rod into swivel arm and then close the door

• With the door in the closed position, swivel arm so that the pivot is 1-21/2" off the door surface (as shown below)

• Tighten the arm screw securely

“

Adjust closer as required (See page 8 for details)

ACCESSORY INFORMATION

A7139K - 11/01/11

without the express written permission of Sargent Manufacturing Company is prohibited.

11/01/11

A7139K

• Select closer mounting position based Reveal Depth as listed below

TOP JAMB APPLICATION

• Locate and mark hole locations

Note: 3/32" pilot holes are required when Self Tapping Screws are being used

If machine screws are being used, use a drill #16 (.177) and a #12-24 tap

• Install closer body onto the door with 5/8" power adjustment nut end away from hinge

• Install foot & rod assembly onto the frames

INSTRUCTIONS FOR INSTALLING TOP JAMB

Closer mounted on frame above stop side of door

• Install main arm on the closer with index mark on spindle aligned with the number on the arm

Note: Left Hand Doors – align index mark with the #3 on the main arm (as shown)

Right hand Door – align index mark with the #1 on the main arm (as shown)

• This requires the spindle to be rotated

• Rotate the spindle on the top of the closer to align index mark and the required number on the arm

• Opening the door slightly, slide rod into swivel arm and then

close the door

• With the door closed, position the main arm so it is at 90º to

the door surface

• Tighten the arm screw securely

• Adjust door speed and latching speed valves to achieve the desired closing time. Recommend 6 seconds minimum

for 90º to the closed position

• If backcheck is required, adjust valve to achieve a slight cushioning effect. Auxiliary stop required.

• If closer is equipped with delayed action, regulate valve to achieve the desired delay

A7139K - 11/01/11

without the express written permission of Sargent Manufacturing Company is prohibited.

FINAL ADJUSTMENT AND REGULATING PROCEDURE

Adjust closing power to the minimum required

to reliably close and latch door

• If door is hard to open, decrease power slightly

• If door does not latch, increase power as required

• Use the chart (on the left) as a starting point

• Doors adjusted with high closing power to

overcome strong draft conditions may exceed

ADA standards

without the express written permission of Sargent Manufacturing Company is prohibited.

11/01/11

A7139K

Additional Power Adjustment

Adjusting foot for additional closing

power (for standard and top jamb

applications only)

1. For top jamb and corner bracket

applications: The door closer foot will

be attached to the door in a manner

similar to that shown for mounting the

closer body

2. For doors 2-1/4" thick: Mortise nut

shown for 1-3/4" thick doors will be

furnished along with appropriate length

through-bolts, door construction must

provide a bridge type reinforcement to

prevent the door rail form collapsing

with through-bolts are tightened.

INSTALL COVER AS FOLLOWS:

For standard an parallel arm application

• Screw short cover screw (#8-32 x 5/16") into top of case

approximately 2 turns

• Assemble plastic support and long cover screw (#8-32 x 1-1/4")

into bottom of case approximately 2 turns

• Hold support against case and slide cover into gap between

flange and screw head

• Position cover on closer and tighten screws

For top jamb application

• Assemble plastic support and long cover screw (#8-32 1-1/4")

into top of case approximately 2 turns

• Screw short cover screw (#8-32 x 5/16") into bottom of case

approximately 2 turns

• Slide cover into gap between flange and screw head. Position

cover on closer and tighten screws

Through Bolts

Sargent 1431 Door Closer With UO/O/RO/O8/OLC/P9/RP9/P3/P3A/P4/P4A/Z/OZA Standard Duty Arms (Without Hold Ope A7139K

Navigation menu

Versions of this User Manual:

Views

Navigation