Sargent Installation Instructions For 268/269 Series Concealed Door Closers (with 'CSPS/CSPD' Position A7326C

User Manual: Sargent Installation Instructions for 268/269 Series Concealed Door Closers (with 'CSPS/CSPD' Door Position Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 3

Download
Open PDF In Browser	View PDF

268, 269 (CSPS OR CSPD)
SECURITY OVERHEAD CONCEALED DOOR CLOSER
WITH INTEGRATED SINGLE OR DOUBLE SWITCH
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

VERIFY THE HAND OF THE CLOSER BEFORE INSTALLING. REFERRING TO THE STAMPING ON THE CLOSER END CAP AS SHOWN

268/269 CSPS/CSPD DOOR CLOSERS ARE HANDED AND SHOULD BE SAME HAND AS DOOR

MODEL NUMBER
AND HANDING

LEFT
HAND DOOR

STOP (PUSH) SIDE

DATE CODE:
MONTH AND YEAR

PULL
HINGE SIDE

WITH POWER OFF, CONNECT WIRES AND INSTALL CLOSER INTO PREPARED FRAME WITH
SPRING ADJUSTMENT SCREW AWAY FROM HINGE. (268 CSPS DOOR CLOSER SHOWN)

RIGHT
HAND DOOR

STOP (PUSH) SIDE

INSTALL TRACK IN DOOR AS SHOWN USING
TAMPER PROOF SECURITY SCREWS
PROVIDED.

CUTOUT AWAY
FROM HINGES

OPTIONAL: 268 CSPD
DOOR CLOSER HAS TWO
SETS OF WIRES
HINGE EDGE
OF DOOR
4 EACH
12-24 X 5/8" MS
(PROVIDED)

RED– NORMALLY CLOSED
BLUE– NORMALLY OPEN
BLACK– COMMON

FROM DOOR
POSITION SWITCH

TO MONITORING SYSTEM

INSERT ARM ROLLER INTO TRACK THRU
CUTOUT AND TEMPORARILY LET ARM
LAY ON A TRACK.

When using the optional
circuit tester, refer to page 3
for instructions

ASSEMBLY OF ARM TO DOOR
CLOSER SPINDLE

1. USING 1/8" ALLEN WRENCH, TURN LATCHING
SPEED AND DOOR CLOSING SPEED VALVES
(SEE FIGURE 1) CLOCKWISE UNTIL THEY STOP.
DO NOT FORCE VALVES.
2. USING ADJUSTABLE WRENCH, ROTATE
DOOR CLOSER SPINDLE (SEE FIGURE 1)
90° CLOCKWISE FOR LEFT HAND DOOR AND
COUNTER CLOCKWISE FOR RIGHT HAND DOOR.
3. OPEN DOOR APPROXIMATELY 50° WITH THE
DOOR CLOSER SPINDLE NOW STATIONARY,
MOVE THE END OF THE ARM TO THE SPINDLE
END UNTIL SQUARE HOLE IN THE ARM LINES
UP WITH THE SPINDLE END SQUARE (AS SHOWN).
PUSH ARM UP INTO POSITION ON THE SPINDLE
AND SECURE WITH SECURITY SCREW
AND WASHER.
4. RETURN LATCHING AND DOOR SPEED
VALVES TO NORMAL POSITION

INDEX MARK
ON SPINDLE

R.H. SHOWN VIEW
LOOKING UP

MAIN

ARM

Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

A7326C 06-15-09

FINAL ADJUSTMENT AND REGULATING PROCEDURE
SWITCH ACTUATION POINT ADJUSTMENT
(SEE FIGURE 1)

1. REMOVE TOP PLATES FROM THE CLOSER (IF REQUIRED).
2. TO ACCESS THE ADJUSTMENT SCREW, OPEN THE DOOR
ABOUT 10°.
3. TO ADJUST SWITCH TO RESPOND WHEN DOOR IS NEARER
THE CLOSED POSITION, LOOSEN ADJUSTMENT SCREW
SLIGHTLY AND USING THE HEX KEY AS DRIVE ROTATE
CAM FOR SMALL ANGLE:
—CLOCKWISE FOR RIGHT HAND DOOR
—COUNTER CLOCKWISE FOR LEFT HAND DOOR
TIGHTEN THE ADJUSTMENT SCREW. CLOSE THE DOOR.
IF THE SWITCH DOES NOT RESPOND IN THE DESIRED DOOR
POSITION, REPEAT ADJUSTMENT.

1/16 HEX KEY CAM ADJUSTMENT SCREW

FIGURE 1

CLOSING SPEED
RANGE

BACKCHECK
RANGE

LATCHING
SPEED RANGE

3/16" SPRING POWER
ADJUSTING SCREW

FIGURE 2

BACKCHECK
VALVE
CLOSING
SPEED VALVE

LATCHING
SPEED VALVE

REGULATING DOOR SPEED AND LATCHING SPEED
USE 1/8" ALLEN WRENCH AND TURN VALVES CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT. SEE FIGURE 2.

REGULATING BACKCHECK
THE INTENSITY OF BACKCHECK ACTION IS REGULATED BY A BACKCHECK VALVE.
TURN CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE CHECKING.

CAUTION: SET VALVE FOR A SLIGHT CUSHIONING EFFECT; IT IS DAMAGING TO CLOSER IF
THE CHECKING ACTION IS TOO ABRUPT. BACKCHECK SHOULD NEVER BE USED IN LIEU OF
A DOOR STOP.

3/16 HEX

SPRING POWER ADJUSTMENT
FOR EXTERIOR DOORS AND WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER
AS NEEDED BY TURNING SPRING ADJUSTING SCREW CLOCKWISE.
IF NECESSARY, DECREASE SPRING POWER TO LOWER OPENING FORCE BY ROTATING
SPRING ADJUSTING SCREW COUNTERCLOCKWISE. ONLY OPEN DOOR A FEW INCHES
WHILE ADJUSTING.

INSTALL TOP PLATES USING SECURITY
SCREWS WHEN ALL ADJUSTMENTS
ARE MADE. 8 SCREWS REQUIRED

A7326C 06-15-09

ACCESSORIES

HOW TO USE CIRCUIT TESTER
1. REMOVE COVER PLATES AND PULL PLUG CONNECTION DOWN THROUGH SLOT AND DISCONNECT
2. CONNECT CIRCUIT TESTER AND PUSH PLUG CONNECTION BACK INTO SLOT SO DOOR COULD CLOSE
3. REFER TO (STEP F) FOR ADJUSTMENT INSTRUCTIONS
GREEN LIGHT ON CIRCUIT TESTER INDICATES THAT DOOR IS CLOSED, RED LIGHT INDICATES DOOR IS OPEN.
4. ONCE SWITCH IS ADJUSTED DISCONNECT CIRCUIT
TESTER AND RE-ASSEMBLE
ORDERED SEPARATELY,
USE PART NUMBER 63-4335 WHEN ORDERING

GREEN

RED

TROUBLESHOOTING 268 CSPS/CSPD
PROBLEM: NO SIGNAL FROM DOOR POSITION SWITCH TO THE MONITORING/ALARM SYSTEM
AFTER ALL POSSIBLE ADJUSTMENTS WERE MADE.
CHECK:

BLACK
(C)

SWITCH ASSEMBLY

HOW TO CHECK SWITCH ASSEMBLY:
• DISCONNECT POWER FROM THE UNIT
• REMOVE UNIT FROM FRAME
• DISCONNECT SWITCH ASSEMBLY FROM MONITORING SYSTEM
• CHECK SWITCH ASSEMBLY FOR OPEN CIRCUIT

SWITCH
BLUE
(N.O.)

RED
(N.C.)
CIRCUIT CHECK:
1. MAKE SURE SWITCH IS ACTUATED.
2. SET METER TO OHMS (Ω).
3. PUT ONE LEAD OF METER TO POST OF BLACK WIRE (C) AND OTHER LEAD TO POST OF RED WIRE (NC) ON THE
CONNECTOR. METER SHOULD SHOW OPEN CIRCUIT.
4. LOOSEN THE ADJUSTMENT SCREW AND ROTATE THE CAM TO DEACTIVATE THE SWITCH. METER SHOULD SHOW CLOSE CIRCUIT.
5. PUT ONE LEAD OF METER TO POST OF BLACK WIRE (C) AND OTHER LEAD TO POST OF BLUE WIRE (NO) ON THE CONNECTOR.
METER SHOULD SHOW OPEN CIRCUIT.
6. ROTATE THE CAM TO ACTIVATE THE SWITCH. METER SHOULD SHOW CLOSE CIRCUIT.
IF SWITCH ASSEMBLY WORKS AS DESCRIBED: – REINSTALL CLOSER
– ADJUST SWITCH ACTUATION POINT AS DESCRIBED IN STEP F
– INSTALL TOP PLATES

IF SWITCH ASSEMBLY IS WORKING PROPERLY PROBLEM MAY BE ELSEWHERE IN THE SYSTEM. CHECK THE MONITORING/ALARM SYSTEM.

A7326C 06-15-09

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments
Creator                         : QuarkXPress(R) 7.5
Create Date                     : 2009:08:07 08:23:16
Modify Date                     : 2009:08:07 08:23:16
Producer                        : QuarkXPress(R) 7.5
Title                           : Layout 1

EXIF Metadata provided by EXIF.tools

Sargent Installation Instructions For 268/269 Series Concealed Door Closers (with 'CSPS/CSPD' Position A7326C

Navigation menu

Versions of this User Manual:

Views

Navigation