Sargent Installation Instructions For 268/269 Series Concealed Door Closers (with 'CSPS/CSPD' Position A7326C

User Manual: Sargent Installation Instructions for 268/269 Series Concealed Door Closers (with 'CSPS/CSPD' Door Position Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 3

WITH POWER OFF, CONNECT WIRES AND INSTALL CLOSER INTO PREPARED FRAME WITH

SPRING ADJUSTMENT SCREW AWAY FROM HINGE. (268 CSPS DOOR CLOSER SHOWN)

INSERT ARM ROLLER INTO TRACK THRU

CUTOUT AND TEMPORARILY LET ARM

LAY ON A TRACK.

VERIFY THE HAND OF THE CLOSER BEFORE INSTALLING. REFERRING TO THE STAMPING ON THE CLOSER END CAP AS SHOWN

A

ASSEMBLY OF ARM TO DOOR

CLOSER SPINDLE

1. USING 1/8" ALLEN WRENCH, TURN LATCHING

SPEED AND DOOR CLOSING SPEED VALVES

(SEE FIGURE 1) CLOCKWISE UNTIL THEY STOP.

DO NOT FORCE VALVES.

2. USING ADJUSTABLE WRENCH, ROTATE

DOOR CLOSER SPINDLE (SEE FIGURE 1)

90° CLOCKWISE FOR LEFT HAND DOOR AND

COUNTER CLOCKWISE FOR RIGHT HAND DOOR.

3. OPEN DOOR APPROXIMATELY 50° WITH THE

DOOR CLOSER SPINDLE NOW STATIONARY,

MOVE THE END OF THE ARM TO THE SPINDLE

END UNTIL SQUARE HOLE IN THE ARM LINES

UP WITH THE SPINDLE END SQUARE (AS SHOWN).

PUSH ARM UP INTO POSITION ON THE SPINDLE

AND SECURE WITH SECURITY SCREW

AND WASHER.

4. RETURN LATCHING AND DOOR SPEED

VALVES TO NORMAL POSITION

LEFT

HAND DOOR

RIGHT

HAND DOOR

PULL

HINGE SIDE

PULL

HINGE SIDE

STOP (PUSH) SIDE STOP (PUSH) SIDE

268/269 CSPS/CSPD DOOR CLOSERS ARE HANDED AND SHOULD BE SAME HAND AS DOOR

RED– NORMALLY CLOSED

BLUE– NORMALLY OPEN

BLACK– COMMON

FROM DOOR

POSITION SWITCH TO MONITORING SYSTEM

MAINARM

INDEX MARK

ON SPINDLE

R.H. SHOWN

VIEW

LOOKING UP

OPTIONAL: 268 CSPD

DOOR CLOSER HAS TWO

SETS OF WIRES

4 EACH

12-24 X 5/8" MS

(PROVIDED)

B

DE

DATE CODE:

MONTH AND YEAR

MODEL NUMBER

AND HANDING

When using the optional

circuit tester, refer to page 3

for instructions

CINSTALL TRACK IN DOOR AS SHOWN USING

TAMPER PROOF SECURITY SCREWS

PROVIDED.

HINGE EDGE

OF DOOR

CUTOUT AWAY

FROM HINGES

1

268, 269 (CSPS OR CSPD)

SECURITY OVERHEAD CONCEALED DOOR CLOSER

WITH INTEGRATED SINGLE OR DOUBLE SWITCH

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.

FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.

All rights reserved. Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A7326C 06-15-09

REGULATING DOOR SPEED AND LATCHING SPEED

USE 1/8" ALLEN WRENCH AND TURN VALVES CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT. SEE FIGURE 2.

REGULATING BACKCHECK

THE INTENSITY OF BACKCHECK ACTION IS REGULATED BY A BACKCHECK VALVE.

TURN CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE CHECKING.

INSTALL TOP PLATES USING SECURITY

SCREWS WHEN ALL ADJUSTMENTS

ARE MADE. 8 SCREWS REQUIRED

2

SWITCH ACTUATION POINT ADJUSTMENT

(SEE FIGURE 1)

1. REMOVE TOP PLATES FROM THE CLOSER (IF REQUIRED).

2. TO ACCESS THE ADJUSTMENT SCREW, OPEN THE DOOR

ABOUT 10°.

3. TO ADJUST SWITCH TO RESPOND WHEN DOOR IS NEARER

THE CLOSED POSITION, LOOSEN ADJUSTMENT SCREW

SLIGHTLY AND USING THE HEX KEY AS DRIVE ROTATE

CAM FOR SMALL ANGLE:

—CLOCKWISE FOR RIGHT HAND DOOR

—COUNTER CLOCKWISE FOR LEFT HAND DOOR

TIGHTEN THE ADJUSTMENT SCREW. CLOSE THE DOOR.

IF THE SWITCH DOES NOT RESPOND IN THE DESIRED DOOR

POSITION, REPEAT ADJUSTMENT.

CLOSING SPEED

RANGE

LATCHING

SPEED RANGE

BACKCHECK

RANGE

FIGURE 1

F

G

FINAL ADJUSTMENT AND REGULATING PROCEDURE

H

3/16 HEX

CAUTION: SET VALVE FOR A SLIGHT CUSHIONING EFFECT; IT IS DAMAGING TO CLOSER IF

THE CHECKING ACTION IS TOO ABRUPT. BACKCHECK SHOULD NEVER BE USED IN LIEU OF

A DOOR STOP.

I

J

R

SPRING POWER ADJUSTMENT

FOR EXTERIOR DOORS AND WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER

AS NEEDED BY TURNING SPRING ADJUSTING SCREW CLOCKWISE.

IF NECESSARY, DECREASE SPRING POWER TO LOWER OPENING FORCE BY ROTATING

SPRING ADJUSTING SCREW COUNTERCLOCKWISE. ONLY OPEN DOOR A FEW INCHES

WHILE ADJUSTING.

1/16 HEX KEY CAM ADJUSTMENT SCREW

FIGURE 2

3/16" SPRING POWER

ADJUSTING SCREW

BACKCHECK

VALVE

CLOSING

SPEED VALVE

LATCHING

SPEED VALVE

Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.

All rights reserved. Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A7326C 06-15-09

PROBLEM: NO SIGNAL FROM DOOR POSITION SWITCH TO THE MONITORING/ALARM SYSTEM

AFTER ALL POSSIBLE ADJUSTMENTS WERE MADE.

CHECK: SWITCH ASSEMBLY

HOW TO CHECK SWITCH ASSEMBLY:

•DISCONNECT POWER FROM THE UNIT

• REMOVE UNIT FROM FRAME

• DISCONNECT SWITCH ASSEMBLY FROM MONITORING SYSTEM

• CHECK SWITCH ASSEMBLY FOR OPEN CIRCUIT

CIRCUIT CHECK:

1. MAKE SURE SWITCH IS ACTUATED.

2. SET METER TO OHMS (Ω).

3. PUT ONE LEAD OF METER TO POST OF BLACK WIRE (C) AND OTHER LEAD TO POST OF RED WIRE (NC) ON THE

CONNECTOR. METER SHOULD SHOW OPEN CIRCUIT.

4. LOOSEN THE ADJUSTMENT SCREW AND ROTATE THE CAM TO DEACTIVATE THE SWITCH. METER SHOULD SHOW CLOSE CIRCUIT.

5. PUT ONE LEAD OF METER TO POST OF BLACK WIRE (C) AND OTHER LEAD TO POST OF BLUE WIRE (NO) ON THE CONNECTOR.

METER SHOULD SHOW OPEN CIRCUIT.

6. ROTATE THE CAM TO ACTIVATE THE SWITCH. METER SHOULD SHOW CLOSE CIRCUIT.

IF SWITCH ASSEMBLY WORKS AS DESCRIBED: – REINSTALL CLOSER

– ADJUST SWITCH ACTUATION POINT AS DESCRIBED IN STEP F

– INSTALL TOP PLATES

IF SWITCH ASSEMBLY IS WORKING PROPERLY PROBLEM MAY BE ELSEWHERE IN THE SYSTEM. CHECK THE MONITORING/ALARM SYSTEM.

SWITCH

BLACK

(C)

BLUE

(N.O.)

RED

(N.C.)

3

TROUBLESHOOTING 268 CSPS/CSPD

HOW TO USE CIRCUIT TESTER

1. REMOVE COVER PLATES AND PULL PLUG CONNECTION DOWN THROUGH SLOT AND DISCONNECT

2. CONNECT CIRCUIT TESTER AND PUSH PLUG CONNECTION BACK INTO SLOT SO DOOR COULD CLOSE

3. REFER TO (STEP F) FOR ADJUSTMENT INSTRUCTIONS

GREEN LIGHT ON CIRCUIT TESTER INDICATES THAT DOOR IS CLOSED, RED LIGHT INDICATES DOOR IS OPEN.

4. ONCE SWITCH IS ADJUSTED DISCONNECT CIRCUIT

TESTER AND RE-ASSEMBLE

ORDERED SEPARATELY,

USE PART NUMBER 63-4335 WHEN ORDERING

GREEN

RED

ACCESSORIES

Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.

All rights reserved. Reproduction in whole or in part without the express written

permission of Sargent Manufacturing Company is prohibited.

A7326C 06-15-09