Sargent Instructions For Installing 351 Series Door Closers With PS & PSH Holder Arms A7343G Low Res
User Manual: Sargent Instructions for Installing 351 Series Door Closers with PS & PSH Holder Arms Instruction Sheets
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
351 Door Closers with PS/PSH Arms Installation Instructions 351 SERIES ADJUSTABLE FROM SIZE 1 THRU 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE For assistance, contact SARGENT at 800-727-5477 or www.sargentlock.com 1 Determine maximum degree of door opening or hold open (PSH) required. Drill and tap door and frame for #12-24 machine screws. When using self-tapping screws provided, predrill with 3/32" drill. DEGREE OF DOOR OPENING AT “HOLD OPEN” n 85° DIM. “A” 10-9/16" DIM. “B” 11-5/16" 90° 9-7/8" 10-5/8" 95° 9-3/16" 9-15/16" 100° 8-5/8" 9-3/8" 105° 8-1/8" 8-7/8" 110° 7-5/8" 8-3/8" 2-5/8" (From stop) n Dimensions for given degree based on 4-1/2" butts. If 3-1/2" or 6" hinge is used, hold open angle will change by less than 1/2°. B 2-1/2" Dead stop occurs 3° beyond hold open. C L OF HINGE 9" C L OF HINGE A Pull Side Pull Side Push Side Push Side Left Hand Door Right Hand Door Closers are Non-Handed 13/16" 1-7/8" + 5/16" or IMPORTANT NOTICE PRE-DRILL 3/32" HOLES FOR SELFTAPPING SCREWS OR TAP #12-24 FOR MACHINE SCREWS 2 3-1/16" 2-11/16" Install stop with 1/4" hex wrench to match hand of door. Turn stop counterclockwise until seated very tight. 1/4" HEX WRENCH 13/16" 1-15/16" 3-7/8" Install door closer to door with spring adjustment nut away from hinge. Right Hand Door Shown SPRING ADJUSTMENT NUT 3A PLUG 3B STOP Mount foot bracket to door stop. PSH arm shown PS similar RH 1/2" 7/8" 5/8" Use fifth hole spacer when required IMPORTANT: Use a minimum of 5 screws. 3C Alternate: Pre-assemble arm prior to attaching to stop. NOTE: 351 closer bodies are non-handed. It is important that the closer body is installed with “RH” symbol at top for right hand doors, “LH” symbol at top for left hand doors. Copyright © SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited. A7343G 1 4 * A. Rotate bottom spindle 45° with wrench B. Assemble main arm with index mark 4A Alternate Method: Attach pre-assembled arm positioned as shown C. Secure with screw and washer C B Left Hand Door Opposite C RH B A A 5 3 2 4 1 A. Open door and install pivot as shown B. Use screw to secure pivot and arms 5 1 5 A 2 B 3 4 If not properly indexed, DOOR !! * WARNING: CLOSER will not FUNCTION PROPERLY !! Accessories OPTIONAL: Use mortise nuts (#4TB) when through-bolting is required 125 VF Bracket for flush frame and door condition Flush frame Door See Page 1 for Templating Dimensions 125 V Bracket for narrow frame condition 351-D Drop Bracket Used with narrow top rails 581-2 Spacer Used with blade stops 351-D Drop Bracket D O O R 2 A7343G Copyright © SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited. Final Adjustment and Regulating Procedures 6 Minimum recommended door closing time is 6 seconds for doors opened to 90 degrees. Use 1/8" Hex (Allen) wrench to adjust valves as needed.* Closing and latching speeds: Turn valves clockwise to slow down or counterclockwise to speed up door movement. Backcheck: To regulate the intensity of backcheck action turn valve clockwise to increase or counterclockwise to decrease checking. CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. CLOSER CAN BE DAMAGED IF THE CHECKING ACTION IS TOO ABRUPT. NEVER USE THE BACKCHECK AS A DOOR STOP. ALWAYS USE A DOOR STOP TO STOP THE DOOR. Delayed Action Feature (optional feature on some models): “Delayed Action” provides slow door closing through the delayed action range. Turn valve clockwise to slow down or counterclockwise to speed up door movement. SPEED UP SLOW DOWN Delayed Action Range Closing Speed Range Latching Speed Range Backcheck Range 1/8" Hex socket wrench * If adjustments are ineffective, check indexing from step 4. 7 Adjust power to allow door to close and latch. Increase NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT DOOR WIDTH (INCHES) EXTERIOR DOORS 24-30 TURN nut 1-3 TURN nut 1-3 30-36 FACTORY SET FACTORY SET 36-42 TURN nut 1-4 TURN nut 1-3 42-48 TURN nut 7-9 TURN nut 4-6 INTERIOR DOORS Adjusting door to close due to high draft conditions may exceed ADA standards. Consult local ordinances when fire doors are involved. 8 9 Install cover as shown. Decrease To adjust holder arm (PSH only) All PSH arms are set in hold open at the factory. To inactivate, turn the adjusting nut approximately 1-1/2 turns counter-clockwise. Adjusting nut INSERT IS REMOVABLE. PLACE IN UNUSED OPENING. Copyright © SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited. A7343G 3 Copyright © SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited. A7343G 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00 Instance ID : uuid:036107d8-6203-3040-bad2-73ecd12c1815 Document ID : adobe:docid:indd:e92ab914-9346-11e0-bd82-9074606a0773 Original Document ID : adobe:docid:indd:e92ab914-9346-11e0-bd82-9074606a0773 Rendition Class : proof:pdf History Action : saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:628F0020082068118A6DB2BEDDD58100, xmp.iid:638F0020082068118A6DB2BEDDD58100, xmp.iid:9FB5023F0A2068118A6DB2BEDDD58100, xmp.iid:E41400D0152068118A6DB2BEDDD58100, xmp.iid:C02C9701162068118A6DB2BEDDD58100, xmp.iid:30BC01A9162068118A6DB2BEDDD58100, xmp.iid:F5C2A9F7162068118A6DB2BEDDD58100, xmp.iid:05B0762B172068118A6DB2BEDDD58100 History When : 2011:06:13 09:47:16-04:00, 2011:06:13 09:47:16-04:00, 2011:06:13 10:02:27-04:00, 2011:06:13 11:25:14-04:00, 2011:06:13 11:26:38-04:00, 2011:06:13 11:31:19-04:00, 2011:06:13 11:33:30-04:00, 2011:06:13 11:34:57-04:00 History Software Agent : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Create Date : 2011:06:13 11:37:14-04:00 Modify Date : 2011:06:13 11:37:20-04:00 Metadata Date : 2011:06:13 11:37:20-04:00 Creator Tool : Adobe InDesign CS5 (7.0) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 3836 bytes, use -b option to extract), (Binary data 12739 bytes, use -b option to extract) Doc Change Count : 65 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 4 Creator : Adobe InDesign CS5 (7.0)EXIF Metadata provided by EXIF.tools