Sargent KP8200 Keypad Mortise Lock Programming Instructions A7373

User Manual: Sargent KP8200 Keypad Mortise Lock Programming Instructions Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 23

Download
Open PDF In Browser	View PDF

KP Series
Keypad Mortise Lock

Installation & Programming
Instructions

A7373C
03/14

Copyright 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.

Table of Contents

Warning ....................................................................................3

General Description..................................................................4

Specifications...........................................................................4

Features....................................................................................5

Parts Breakdown......................................................................6

Installation Instructions...........................................................8

Operational Check..................................................................18

Programming Instructions ....................................................18

Warning

Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.

03/31/14

Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening,
and SARGENT makes no representations or warranties concerning what such impact may be in any specific
situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new
fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to
ensure compliance with all applicable codes and ratings

To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.
Do not install batteries if controller is powered by external power supply.

Warning SARGENT Mfg. Co. locksets utilizing a door position switch (DPS)
are not rated for, or intended for use in life safety applications.

1-800-810-WIRE • www.sargentlock.com • A7373C

Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

KP Series
Keypad Mortise Lock

General Description
The SARGENT KP Series Mortise Lock is designed for areas which require stand alone
authorized entry. It is a self-contained microprocessor-controlled keypad with non-volatile memory.
The keypad holds a total of 100 different user codes. User codes 01, 02 and 03 are utilized for
Master Code, Emergency Code and Supervisory Code, respectively.
This motorized 8200 mortise lock is operated by four (4) “C” alkaline batteries.
SARGENT mortise locks are designed with quality components to provide high security,
performance and durability.

03/31/14

Specifications
•

Latchbolt - Stainless Steel

•

Deadbolt - Stainless Steel

•

Guardbolt - Stainless Steel, non handed

•

Handed - Easily field reversible without
disassembling the lock body

•

Case - 12 gauge heavy duty wrought steel

•

Outside lever controlled by keypad

•

Inside lever retracts latchbolt and deadbolt

•

Locks furnished for 1 3/4” doors. Can
be furnished for other door sizes upon
request. (Consult factory)

•

UL Listed (3 hr.)

•

Accepts size 41(standard) and 42
(removable core) SARGENT mortise
cylinders (KP8276 and KP8278)

•

Key retracts latchbolt (KP8276 and
KP8278)

•

Operates utilizing any two to six digits
per code. Digits may be repeated and
codes may start with zero

•

Adjustable unlock time

•

Entry of three wrong User Codes
disables all codes for ten seconds.
Green LED flashes.

•

Piezo horn can be heard with each
keystroke or turned off by Master or
Supervisory Code

•

Last 15 transactions can be output to
printer via Data Transfer Device (DTD)

•

100 users total: one Master Code, one
Emergency Code, one Supervisory
Code, with the rest being standard
codes, passage codes, or one time
only codes

Features
•

Non-volatile memory

•

Motor driven, battery operated mortise lock

•

Battery operated with 4 (each) “C” Alkaline

•

Low battery alert – 4 chirps after code entry

•

Option Code available to sound horn every
time keypad is pressed

•

External remote “request to enter” connector
requires wire harness (52-2071)

•

External battery input connector included to
power unit in event of battery failure

•

All programming done at keypad

•

Deadbolt switch inside mortise lock allows
Emergency Code and Master Code users to
gain entry when deadbolt is thrown*

* PHR-prefix locks will not allow Emergency or Master Code users entry when deadbolt is thrown.
Entry is through key cylinder override only.

1-800-810-WIRE • www.sargentlock.com • A7373C

KP Series
Keypad Mortise Lock

Features (continued)

KP8276
•
•

KP8278
Deadbolt function
Cylinder override provided

•
•

KP8277
•
•

Deadbolt function
No cylinder override

KP8279
Cylinder override provided
No deadbolt function

•
•

No cylinder override
No deadbolt function

Keypad
Tactile keypad made of Ultraviolet stable material
LED’s indicate valid or invalid entries
Green LED indicates unlocked.Yellow LED indicates unit is in programming mode
Flashing green and yellow LED’s indicate deadbolt thrown or lock set in passage mode
Infrared LED for transaction output. Provides last 15 valid codes.

•
•
•
•
•
•
•

Outside Escutcheon with Keypad
Outside Lever Handle Assembly
Inside Lever Handle
Mortise cylinder
Inside Escutcheon with Circuit Board
and Battery Pack
Batteries (4 “C”)
Tool (security socket screw key 1/8”)

Items included in your KP8277/KP8279
Keypad Mortise Lock:

•
•
•
•
•
•

Outside Escutcheon with Keypad
Outside Lever Handle Assembly
Inside Lever Handle
Inside Escutcheon with Circuit Board
and Battery Pack
Batteries (4 “C”)
Tool (security socket screw key 1/8”)

1-800-810-WIRE • www.sargentlock.com • A7373C

Items included in your KP8276/KP8278
Keypad Mortise Lock:

03/31/14

•
•
•
•
•

03/31/14

KP Series
Keypad Mortise Lock

Parts Breakdown
KP Series Parts List

3
2
14
16

25
1

8
4

6
10

Inside of Door

1-800-810-WIRE • www.sargentlock.com • A7373C
5
15

12
17

13
19
18
KP8276
ONLY
KP8278
20

11
21

Outside of Door

KP Series
Keypad Mortise Lock
Parts Breakdown (Continued)
Req.

Description

01-0803

Battery Alkaline (“C” cell)

2
3
4
5
6

01-1119
01-0297
01-1157
01-0440
81-0467
81-0468
81-0490
81-0470
81-0471
81-4648
81-0447
81-0489
81-0513
81-0445
01-1472
01-1174

#8-32 x 1-1/2 Flat Head Screw
Security Socket Screw Key (1/8)
#8-32 x 1-1/4 Phillips Pan Head Screw
Flat Washer
Inside Lever (L.H.) A” Design
Inside Lever (R.H.) A” Design
Inside Lever B” Design
Inside Lever E” Design
Inside Lever F” Design
Inside Lever H” Design
Inside Lever J” Design
Inside Lever L” Design
Inside Lever P” Design
Inside Lever W” Design
Lever Handle Screw A, E, F & H (Lever)
Lever Handle Screw B, J, L, P & W (Lever)

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

8
9
10
11
12
13
14
15
16
17

82-0347
82-0368
81-0093
01-4388
01-1495
82-3088
52-0033
01-1500
52-2340
77-0566

Handle Spring
Spindle
LN” Rose
#8 x 1 Phillips Flat Head Screw
#8-32 x 5/8 Machine Screw
Inside Lever Adapter & Plate Assembly
Fire Stop Plate
#8 x 1/2 Pan Head Self Tapping Screw
Outside Escutcheon & Keypad Assembly
Cylinder Rosette (Size 41 Cylinder)

1
1
1
1
2
1
1
2
1
1

13-0596
13-0489
13-0490

Cylinder Rosette (Size 42 Cylinder)
Cylinder Ring (Size 41 Cylinder)
Cylinder Ring (Size 42 Cylinder)

1
1
1

19
20

13-0140
OS-8276 x LNA

Compression Spring
Outside Lever (R.H.) A” Design
(L.H.) A” Design “

1
1
1

OS-8276 x LNB
OS-8276 x LNE
OS-8276 x LNF
OS-8276 x LNH
OS-8276 x LNJ
OS-8276 x LNL
OS-8276 x LNP
OS-8276 x LNW
OS-8276 x LA

Outside Lever B” Design “
Outside Lever E” Design “
Outside Lever F” Design “
Outside Lever H” Design
Outside Lever J” Design
Outside Lever L” Design
Outside Lever P” Design
Outside Lever W” Design “
Outside Lever (R.H.) A” Design “
(L.H.) A” Design “
Outside Lever B” Design “
Outside Lever E” Design “
Outside Lever F” Design “
Outside Lever H” Design “
Outside Lever J” Design “
Outside Lever L” Design
Outside Lever P” Design “
Outside Lever W” Design
Outside Front #8-32x1/4 FL HD Screw
Lockbody Screws for Wood #12x1-1/4 FL HD (not shown)
Lockbody Screws for Metal #12-24x1/2 FL HD (not shown)
Outside Front (KP8276 & KP8277)
Outside Front (KP8278 & KP8279)

1
1
1
1
1
1
1
1
1

22
23

24
25
26

OS-8276 x LB
OS-8276 x LE
OS-8276 x LF
OS-8276 x LH
OS-8276 x LJ
OS-8276 x LL
OS-8276 x LP
OS-8276 x LW
01-1028
01-2299
01-1019
82-0084
82-0081

KP-8276-hand-finish Lockbody Assembly with deadbolt & cylinder
KP-8277-hand-finish Lockbody Assembly with deadbolt only (no cylinder)
KP-8278-hand-finish
KP-8279-hand-finish
82-3730
82-3729

Lockbody Assembly with cylinder only (no deadbolt)
Lockbody Assembly without deadbolt & without cylinder
Inside Escutcheon Assembly (Turn Lever-KP8276/KP8777)
Inside Escutcheon Assembly (Hole Plug-KP8278/KP8779)

52-4758

Inside Escutcheon Assembly (Turn Lever-KP8276 only*)

Part #

1
1
1
1
1
1
1
1
2
2
2
1
1
1

1
1
1

* PHR-prefix locks will not allow Emergency or Master Code users entry when deadbolt is thrown.
Entry is through key cylinder override only.

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

Item

KP Series
Keypad Mortise Lock

Installation Instructions
Step #1 – Verify Hand and Bevel of Door
A. Verify Hand and Bevel of Door
Stand on outside/locked side of door when determining the door hand

LHRB

Left Hand
Hinges Left
Open Inward

Left Hand
Reverse Bevel
Hinges Left
Open Outward

Right Hand
Hinges Right
Open Inward

RHRB

Right Hand
Reverse Bevel
Hinges Right
Open Outward

Fig. 1A

B. Prepare Door
Prep door according to Instruction Sheet A7454 and appropriate template:
Manufacturer Door Template: 4632

03/31/14

Documents are available at www.sargentlock.com
Inside of Door

Outside of Door
Through-bolt Hole

Ribbon Cable Hole
(Controller to Keypad)

Outside Cylinder Hole
(76 and 78 Functions)

Inside Cylinder Hole

Thumb Turn Lever Hole

Lever Handle Hole

Mortised
Pocket

Lever Handle Hole

Through-bolt Hole
Pre-drilled
and/or
Tapped Holes
(2 places)

Fig. 1B Wood Door Preparation

1-800-810-WIRE • www.sargentlock.com • A7373C

KP Series
Keypad Mortise Lock

Step #2 – Verify Hand and Bevel of Door
A. Reverse Lock Hand
Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):
1. Position lock body with red surface of locking piece visible.
2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.
3. Rotate the locking piece 180° until RED surface is on opposite side.
Note: Red indicates locked side (outside).

Right Hand
Lock Shown
Locking Slide
Red on Locked Side
Push In

B. Reverse Latch Hand
Beveled surface of latchbolt must face strike (Fig. 2B).
The deadlatch is self adjusting.
To change the hand of the latchbolt:
1. Insert the blade of a slotted screwdriver (>1/4”)
into the spade shape slot behind latch.
2. Rotate the screwdriver 90° to push latchbolt out
until back of bolt clears lock case front.

Spade
Shaped
Slot

Latchbolt

3. Rotate latchbolt 180° until the latchbolt
drops back into the lock body.

Deadlatch

Note: Latch cannot be unscrewed.

Fig. 2B

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

Fig. 2A

KP Series
Keypad Mortise Lock
Step #3 – Install Lock Body

Inside of Door

1. Insert lock body into mortised cutout (Fig. 3A).

03/31/14

Fig. 3A

2. Hold lock body loosely in place with (2) lock
body screws.
Note: Do not completely tighten screws at this time.

Outside of Door

Harness exits
Non-Cylinder side

(2) #12-24 x 1/2”
Flat Head Screws
(Metal Doors)

(2) #12 x 1-1/4”
Flat Head Screws
(Metal Doors)

Fig. 3B

1-800-810-WIRE • www.sargentlock.com • A7373C

KP Series
Keypad Mortise Lock

Step #4 – Exterior Door Options
A. Fire Stop Plate (P/N 53-0033)

Fire-rated doors require a fire stop plate on
the outside of the door (Fig. 4A).
1. Drill (2) 1/8” x 1-1/4” deep holes
in the door if not already present.

Ribbon Cable Hole

Refer to template for fire-stop
prep locations.
2. Attach with flap up and
out using (2) #8 x 1/2”
self-tapping screws for
wood and metal doors.

Slot

7/8”

Fig.4B

Fire Stop Plate

of 1-1/2”
Diameter

1-1/2”

Install weather conduit on
NON FIRE-RATED exterior
doors only.

(2) Self Tapping
Screws #8 x 1/2”
for Wood and
Metal Doors

1. Carefully insert the weather
conduit into the ribbon cable
hole on the inside of the door
(Fig. 4B).

O-Ring

Outside of Door

2. Place the O-ring around the
weather conduit on the outside and up against the door
(Fig. 4C).

Fig.4C

Step #5 – Install Weatherseal Gasket (Exterior Doors)

Fig. 4A

Peel back

1. Carefully remove adhesive backing from the gasket (Fig. 5A).
2. Apply gasket to escutcheon:
•

Starting in one place, press the adhesive side
of the gasket firmly against the escutcheon.

•

Work around the escutcheon, pressing the sticky side
of the gasket firmly against the escutcheon edge.

Fig. 5A

•

The gasket should be aligned so that all edges
of the escutcheon are covered.
3. Attach escutcheon to the door.
Note: The 43 cylinder may be used with or without a gasket.

Fig. 5B

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

B. Weather Conduit
(P/N 52-2847)

(2) 1/8” Diameter
Holes Required

03/31/14

KP Series
Keypad Mortise Lock

Step #6 – Install Outside
Escutcheon and Lever
Assembly

Install Outside
Lever Assembly

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

KP Series
Keypad Mortise Lock

Step #7 – Install Inside Escutcheon

Inside Escutcheon
Assembly

03/31/14

KP Series
Keypad Mortise Lock

Step #8 – Inside Lever Installation

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

KP Series
Keypad Mortise Lock
Step #8 – Continued

03/31/14

KP Series
Keypad Mortise Lock

Step #9 – KP8276 and KP8278 Only - Install Cylinder

Position cylinder so that the
SARGENT logo is right-side up.

Correct

1-800-810-WIRE • www.sargentlock.com • A7373C

Incorrect

Step #11 – Battery Installation

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

KP Series
Keypad Mortise Lock
Step #10 – Application of Front Plate

KP Series
Keypad Mortise Lock
7 Operational Check
•
•
•
•
•

Place key into cylinder and rotate key.
The key will retract the latchbolt.
If the deadbolt is thrown, the key will retract both the deadbolt and the latchbolt.
Inside handle lever retracts latchbolt and (if provided).
Enter 1234* to unlock outside lever handle and retract latchbolt and deadbolt (if provided).

N
Q

Deadbolt
(KP8276/KP8278)

03/31/14

Latchbolt

Inside of Door

Outside of Door

• Key should rotate freely. There should be no friction against lock case, wire harness or any
other obstructions.
• Refer to Step 7 if harness friction exists.
• Rotate cylinder further into lock case to eliminate lockbody obstruction.

Programming Instructions
The KP Keypad Lock can support 100 users. Each user is assigned a User Number in addition to
the code used for entry.
Example:

USER TYPE

USER NUMBER

USER CODE
(2-6 DIGITS)

Master

1234

Emergency

22222

Supervisor

303030

Standard

04-97

Special Factory
10 Sec. Time Preset

98
99

1-800-810-WIRE • www.sargentlock.com • A7373C

265
1368

KP Series
Keypad Mortise Lock
This Keypad Mortise Lock has 99 User Codes available for programming purposes.
• The Master Code is always User “01”. The Master Code assigns the Emergency and Supervisory Codes. It is
also used for programming and will override the deadbolt*. Users are deleted through the Master Programming
Code only.
• The Emergency Code is always User “02”. The Emergency Code will override the deadbolt* in the mortise lock
and has an unlock time of 10 seconds.
• The Supervisory Code is always User “03”. The Supervisory Code allows temporary lockout of selected users,
changes duration of unlock time, requests infrared interrogation output, and may add additional User Codes.
• The first User Code will be User “04” or higher. User numbers do not have to be used or entered sequentially.
• User codes “98” and “99” have a factory-set unlock time of ten seconds. This allows a handicapped person
extra time which would not be required by other users.
*NOTE: PHR-prefix locks will not allow Emergency or Master Code users entry when deadbolt is thrown.
Entry (with deadbolt thrown) is through key cylinder override only.

To Begin Programming:
The Keypad Mortise Lock is preset at the factory with Master Code “1234”. Entering “1234*” will unlock the
lock allowing the lever handle to retract the latchbolt.

Initial Set-Up Procedures:
• The following are typical procedures to follow when setting up your KP Series Keypad.
• If a mistake is made during any of procedures, depress the “*” several times until the yellow LED goes out.
• If no keystroke is made in a 30-sec time frame the programming up to that point will default and you will
have to start over.

All of the following procedures start with 99#.
Change Master Code:
• 1234* (Yellow LED Begins to Blink Slowly) This example uses the Factory Default Master Code
• 50# 1# 01# New Master Code* (Yellow LED Blinks Quickly)
• New Master Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)
To Enter the Emergency Code: (Unlock Duration is Factory Set at 10 Sec)
• Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 1# 02# Emergency Code* (Yellow LED Blinks Quickly)
• Emergency Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)
To Enter the Supervisory Code:
• Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 1# 03# Supervisory Code* (Yellow LED Blinks Quickly)
• Supervisory Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)
To Enter a User Code:
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 1# User Number (04-97)# User Code* (Yellow LED Blinks Quickly)
• User Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

If after the last “ *” is depressed, the yellow LED does not go out, depress “ *” once more.

KP Series
Keypad Mortise Lock
All of the following procedures start with 99# (continued).

If after the last “*” is depressed, the yellow LED does not go out, depress “*” once more.

To Enter a Passage (Maintained Mode) Code:
When Passage Mode is used, the same User Code must be used to re-lock the lock.
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 2# User Number (04-97)# User Code* (Yellow LED Blinks Quickly)
• User Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)
To Enter a One Time User Code:
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 50# 3# User Number# User Code* (Yellow LED Blinks Quickly)
• User Code* (Yellow LED Blinks Slowly) * (Yellow LED Goes Out)
To Deactivate “Beep” With the Depression of Each Key:
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 30# 0# 0# (Yellow LED Continues to Blink Slowly)
• * (Yellow LED Blinks Quickly)
• * (No Beep on Depression and Yellow LED Blinks Slowly)
• * (No Beep on Depression and Yellow LED Goes Out)
To Reactivate “Beep” With the Depression of Each Key:
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 30# 0# 1# (Yellow LED Continues to Blink Slowly)
• * (Yellow LED Blinks Quickly)
• * (Beep on Depression and Yellow LED Blinks Slowly)
• * (Beep on Depression and Yellow LED Goes Out)
To Clear the Entire Memory:
• Master Code* (Yellow LED Begins to Blink Slowly)
• 46# 00000# 00000# (Yellow LED Continues to Blink Slowly)
• * (Yellow LED Blinks Quickly)
• * (No Beep on Depression and Yellow LED Goes Out)
• PAUSE, Yellow LED Begins to Blink Again
• * (Yellow LED Goes Out)
NOTE This Deletes ALL Codes, including Master, Emergency and Supervisory. The Master Code is set back
to 1234, Door Number to 0001 and Unlock time to 5 Sec. If the Master Code is not known, Factory
Assistance will be required to clear the memory. 1-800-810-WIRE.
To Program Door Numbers into Keypad:
• Master Code* (Yellow LED Begins to Blink Slowly)
• 43# 0# Door Number# (must be four digits) (Yellow LED Blinks Slowly)
• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Blink Slowly)

03/31/14

• * (Yellow LED Goes Out)

1-800-810-WIRE • www.sargentlock.com • A7373C

KP Series
Keypad Mortise Lock
All of the following procedures start with 99# (continued).

If after the last “*” is depressed, the yellow LED does not go out, depress “*” once more.

To Interrogate Transaction Log:
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 70# 0# 0# (Yellow LED Blinks Slowly)
Seq

User

Trans

001

003

Hold an infrared printer up to the red
infrared LED (as shown). A Data Transfer
Device (DTD) can be used to download
information from the keypad to a printout.

003

001

Illustration

003

001

020

001

003

001

Door # 5666

• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Goes Out)

Door Number

For additional information, see “Transaction Log”.
Note: Seq. # 1 is the
programming request
to output the entries.
Sequence numbers 2-6
are the actual entries.

Transaction
Number
User Number

Transaction
Type

To LED
location
DataTransfer Device
(DTD)

To Reset / Clear Transaction Log
• Master Code* (Yellow LED Begins to Blink Slowly)
• 76# 00000# 00000# (Yellow LED Blinks Slowly)
• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Goes Out)
To Delete a User Number:
• User Number# (Yellow LED Blinks Slowly)
• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Blinks Slowly)
• * (Yellow LED Goes Out)
To Disable / Enable a User Number:
• Supervisory or Master Code* (Yellow LED Begins to Blink Slowly)
• 56# 0# = Enable, 1# = Disable User Number# (04-99) (Yellow LED Blinks Slowly)
• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Blinks Slowly)
• * (Yellow LED Goes Out)
To Set Unlock Time:
• Master Code* (Yellow LED Begins to Blink Slowly)
• 85# Time Duration# (01-99 Sec) 0# (Yellow LED Blinks Slowly)
• * (Yellow LED Begins to Blink Quickly)
• * (Yellow LED Blinks Slowly)
• * (Yellow LED Goes Out)
Note:

The Unlock Time is Adjustable for Momentary Operation. A 5 second unlock time is recommended to extend battery life.
Once the unlock time is entered, it is the same for ALL users except 02, 98 and 99 which are factory set for 10 seconds.

1-800-810-WIRE • www.sargentlock.com • A7373C

03/31/14

• Master Code* (Yellow LED Begins to Blink Slowly)

KP Series
Keypad Mortise Lock

Transaction Log
To output the last 15 entries, enter 99 # Supervisory or Master Code * 70 # 0 # 0 # **.
Note: Seq. # 1 is the
programming request
to output the entries.
Sequence numbers 2-6
are the actual entries.

Door Number
• 4 Digits
• Up to 9999 different doors, assigned by user
Transaction Number
• Single digit - 1-6

Door # 5666
Seq

User

Trans

001

003

• Oldest transaction - 6

003

001

User Number
• Three digits - 001 through 099

003

001

020

001

• User numbers assigned at time of programming

003

001

Door Number

• Latest transaction - 1

Transaction
Number

Transaction Types
• 001 = Access granted

Transaction
Type

User Number

• 002 = Access denied (Deadbolt thrown and code entered did not have
proper access level.)
• 003 = Log printed
Optional Equipment

Hold an infrared printer up to the red
infrared LED (as shown). A Data Transfer
Device (DTD) can be used to download
information from the keypad to a printout.

• Printer Paper (6 Rolls) - 52-0034 used for infrared printers
• Auxiliary Power Unit (APU) 52-2065 - used to unlock unit if batteries are too
weak and cylinder is not used.

Illustration

• Data Transfer Device (DTD) - used to download the user and transaction type.
• Remote Unlocking - 52-2071 - used for remote unlocking of keypad mortise
lock. When the deadbolt is thrown and the remote unlocking feature is used,
both the latchbolt and deadbolt can be retracted by turning the lever handle.

Remote unlocking
connector placement

Inside Escutcheon

1-800-810-WIRE • www.sargentlock.com • A7373C

To LED
location
DataTransfer Device
(DTD)

SARGENT Manufacturing Company
100 Sargent Drive
New Haven, CT 06511 USA
800-810-WIRE (9473) • www.sargentlock.com
Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,
electro-mechanical products and access control systems for new construction, renovation, and replacement applications.
The company’s customer base includes commercial construction, institutional, and industrial markets.
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ASSA ABLOY is the global leader in door opening solutions, dedicated to
satisfying end-user needs for security, safety and convenience.

A7373C-03/14

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2014:03:17 15:22:58-04:00
Metadata Date                   : 2014:04:01 11:18:40-04:00
Modify Date                     : 2014:04:01 11:18:40-04:00
Creator Tool                    : Adobe InDesign CC (Windows)
Instance ID                     : uuid:b9772ca1-dab5-4665-bd17-812ca4a74181
Original Document ID            : adobe:docid:indd:c6d5a1b8-1ec5-11dc-9031-b975861f0985
Document ID                     : xmp.id:8177157d-0021-c844-b2a8-24a4fbb7d52b
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4fa2090b-d25f-1847-94a0-7b55639eca7f
Derived From Document ID        : xmp.did:4fa2090b-d25f-1847-94a0-7b55639eca7f
Derived From Original Document ID: adobe:docid:indd:c6d5a1b8-1ec5-11dc-9031-b975861f0985
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC (Windows)
History Changed                 : /
History When                    : 2014:03:17 15:22:58-04:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 23
Creator                         : Adobe InDesign CC (Windows)

EXIF Metadata provided by EXIF.tools

Sargent KP8200 Keypad Mortise Lock Programming Instructions A7373

Navigation menu

Versions of this User Manual:

Views

Navigation