Sargent A7741A 1331 Series Door Closer Installation Instructions With JUO (JO & JP9) Arms A7741

User Manual: Sargent 1331 Series Door Closer Installation Instructions with JUO (JO & JP9) Arms Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

A7741A

Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All
rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.

SARGENT® 1331
DOOR CLOSER INSTALLATION
INSTRUCTIONS WITH JUO (JO & JP9) ARMS
Strength Adjustable From Size 1 Thru 6
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE
Auxiliary door stop required
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477 or www.Sargentlock.com

Choose From 1 of the 3 Applications

JO Standard Arm

JP9 Parallel Arm

JO Top Jamb Arm

Use Standard & Parallel Full Size Templates Provided

Pre-drill - 3/32” holes
for self tapping screws or #16 drill for
#12-24 tap for machine screws

NOTE: With swing clear hinges, use data sheets provided.
*1/4" Variance allowed for retrofit of existing closers
With fasteners provided, secure closer body to door with power adjustment away from hinge.

Using optional mortise nuts when through-bolting
Frame
Frame

Door
Doorstop
stop

Mortise
nutnut
Mortise

Power Adjustment
f

Drill 1/4"
dia.
hole Dia.
for hole
screws

Drill 3/8"
Dia.dia.
Drill
3/8"
hole for
mortise
hole
for
mortise
nut
body
nut body

Unreinforced
Unreinforced door
door

A7741A

1331 STANDARD APPLICATION JO ARM
INSTALLATION INSTRUCTIONS

Determine maximum degree of door opening required. Use a #16 drill. Drill and tap door and frame for 12-24 machine screws.
When using the included self tapping screw, pre-drill with a 3/32” drill *Provides maximum power for heavy or drafty doors

*(120° - 12")
180° - 10-1/8"

1"
1-3/8"

*(120° - 6-12")
180° - 4-5/8"

3/4"
12"
Right hand shown, left hand similar.
With provided fasteners, install foot to frame and secure
closer body to door with power adjustment
away from hinge

For additional power move foot towards hinge
edge of door

Move foot
pivot to hole
nearest hinge

Hinge edge of door

Power Adjustment

On both right and left hand doors, secure main arm to top spindle
with screw and washer provided. Align flat mark as shown

Flat mark

Open door and insert foot into main arm. Close door fully, and while
pushing arm as shown in picture, tighten arm bolt

Arm
Bolt

A7741A

90°

See page 5 for closer
adjustment and cover
installation

A7741A

Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group
company. All rights reserved. Reproduction in whole or in part without the express
written permission of Sargent Manufacturing Company is prohibited.

A7741A

1331 JP9 PARALLEL ARM INSTRUCTIONS

Determine maximum degree of door opening required. Use a #16
drill. Drill and tap door and frame for 12-24 machine screws.
When using the included self tapping screws, predrill with a 3/32"
drill.
*Provides maximum power for heavy
or drafty doors

Center line
of hinge

3-1/2"
3/4"
12"

*(120° - 3-3/4")
180° - 1-1/4"
Right hand shown, left hand opposite.

*(120° - 9-12")
180° - 7"

Center line
of hinge

With fasteners provided, install foot to stop and closer body to
door with power adjustment toward hinge

3/8"
7/16"

3/8"

1" minimum stop
width required

2-3/4"

Power adjustment

3
With wrench on bottom spindle,
preload/index by turning spindle as
shown and secure main arm to top
spindle with flat mark as indicated at
left with screw and washer

Flat mark
Left Hand Door

Right Hand Door

Open door and insert foot into main arm. Close door fully while holding elbow 1-1/4” from door. Tighten arm bolt

1-1/4"
Arm Bolt

Accessory Information

See page 5 for
adjustment and
cover installation
Drop Plate

2-1/2" Min.
1331D
Drop plate used when
top rail is less than 2 1/2"

581-1 Blade Stop Spacer Kit
Metal spacer for use on 1/2" blade
stops on aluminum store fronts

A7741A

CLOSER ADJUSTMENT AND COVER INSTALLATION
1331 JO TOP JAMB INSTRUCTIONS

THE 1331 IS FACTORY ADJUSTED FOR MOST APPLICATIONS, HOWEVER,
ADDITIONAL ADJUSTMENT MAY BE REQUIRED DUE TO ACTUAL CONDITIONS

Determine maximum degree of door opening required.
Use a #16 drill. Drill and tap door and frame for 12-24
machine screws. When using provided self tapping screws,
predrill with a 3/32" drill

*(120° - 6-7/8")

12"

3/4"

180° - 4-3/4" Center line
of hinge

1/2"

1-7/8"
2"

180° - 10-1/4"

*Provides maximum power for heavy or drafty doors

With provided fasteners, install foot to door and closer body
to frame with power adjustment away from hinge

Power Adjustment

Slow
down

Adjusting foot for additional closing power

Move foot
pivot to hole
nearest hinge

Hinge Edge

Speed
up

1/8" HEX wrench

Sweep (Closing)
speed range

Backcheck
range

Hinge edge of door

Note: 2" maximum reveal allowed

IF ADJUSTMENTS ARE INEFFECTIVE, CHECK INDEXING AS SHOWN IN STEP 3 AND CHECK FOR
CORRECT TEMPLATING

*(120° - 12-3/8")

Right hand shown, left
hand similar

MINIMUM RECOMMENDED DOOR CLOSING TIME FOR DOORS OPENED TO 90° IS 6 SECONDS.
Use 1/8" hex (Allen) wrench to adjust valves as needed
SWEEP AND LATCHING SPEEDS:
Turn valves clockwise to slow down or counterclockwise to speed up door movement
BACKCHECK:
To regulate the intensity of backcheck action, turn valve clockwise to increase or counterclockwise to decrease checking
CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. CLOSER CAN BE DAMAGED IF THE CHECKING ACTION IS TOO
ABRUPT. NEVER USE THE BACKCHECK AS A DOOR STOP. ALWAYS USE A DOOR STOP TO STOP THE DOOR

Latching speed
range
Spring power adjustment
1/8"

On both right and left hand doors, secure main arm to top spindle with screw and washer provided. Align flat mark as shown
Sweep

CLOSING POWER:
Backcheck
Certain applications may require closing power adjustment:
If the door will not latch properly, increase power by turning
the power adjustment clockwise in full turn increments.
If the door is hard to open, reduce power by turning the power
adjustment counter-clockwise in full turn increments.

Flat mark

Open door and insert foot into main arm. Close door fully, and while
pushing arm as shown in picture, tighten arm bolt

6
Accessories

Arm
Bolt

Latch

Cover Installation
Move insert if needed. Install cover with two #6- 32 X 5/16" machine screws as shown

90°

Insert

See page 5 for adjustment and cover installation
Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All
rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.

A7741A

CLOSER ADJUSTMENT AND COVER INSTALLATION
1331 JO TOP JAMB INSTRUCTIONS

THE 1331 IS FACTORY ADJUSTED FOR MOST APPLICATIONS, HOWEVER,
ADDITIONAL ADJUSTMENT MAY BE REQUIRED DUE TO ACTUAL CONDITIONS

Determine maximum degree of door opening required.
Use a #16 drill. Drill and tap door and frame for 12-24
machine screws. When using provided self tapping screws,
predrill with a 3/32" drill

*(120° - 6-7/8")

12"

3/4"

180° - 4-3/4" Center line
of hinge

1/2"

1-7/8"
2"

180° - 10-1/4"

*Provides maximum power for heavy or drafty doors

With provided fasteners, install foot to door and closer body
to frame with power adjustment away from hinge

Power Adjustment

Slow
down

Adjusting foot for additional closing power

Move foot
pivot to hole
nearest hinge

Hinge Edge

Speed
up

1/8" HEX wrench

Sweep (Closing)
speed range

Backcheck
range

Hinge edge of door

Note: 2" maximum reveal allowed

IF ADJUSTMENTS ARE INEFFECTIVE, CHECK INDEXING AS SHOWN IN STEP 3 AND CHECK FOR
CORRECT TEMPLATING

*(120° - 12-3/8")

Right hand shown, left
hand similar

Latching speed
range
Spring power adjustment
1/8"

On both right and left hand doors, secure main arm to top spindle with screw and washer provided. Align flat mark as shown
Sweep

Flat mark

Open door and insert foot into main arm. Close door fully, and while
pushing arm as shown in picture, tighten arm bolt

6
Accessories

Arm
Bolt

Latch

Cover Installation
Move insert if needed. Install cover with two #6- 32 X 5/16" machine screws as shown

90°

Insert

A7741A

1331 JP9 PARALLEL ARM INSTRUCTIONS

Center line
of hinge

3-1/2"
3/4"
12"

*(120° - 3-3/4")
180° - 1-1/4"
Right hand shown, left hand opposite.

*(120° - 9-12")
180° - 7"

Center line
of hinge

With fasteners provided, install foot to stop and closer body to
door with power adjustment toward hinge

3/8"
7/16"

3/8"

1" minimum stop
width required

2-3/4"

Power adjustment

3
With wrench on bottom spindle,
preload/index by turning spindle as
shown and secure main arm to top
spindle with flat mark as indicated at
left with screw and washer

Flat mark
Left Hand Door

Right Hand Door

Open door and insert foot into main arm. Close door fully while holding elbow 1-1/4” from door. Tighten arm bolt

1-1/4"
Arm Bolt

Accessory Information

See page 5 for
adjustment and
cover installation
Drop Plate

2-1/2" Min.
1331D
Drop plate used when
top rail is less than 2 1/2"

581-1 Blade Stop Spacer Kit
Metal spacer for use on 1/2" blade
stops on aluminum store fronts

A7741A

1331 STANDARD APPLICATION JO ARM
INSTALLATION INSTRUCTIONS

*(120° - 12")
180° - 10-1/8"

1"
1-3/8"

*(120° - 6-12")
180° - 4-5/8"

3/4"
12"
Right hand shown, left hand similar.
With provided fasteners, install foot to frame and secure
closer body to door with power adjustment
away from hinge

For additional power move foot towards hinge
edge of door

Move foot
pivot to hole
nearest hinge

Hinge edge of door

Power Adjustment

On both right and left hand doors, secure main arm to top spindle
with screw and washer provided. Align flat mark as shown

Flat mark

Open door and insert foot into main arm. Close door fully, and while
pushing arm as shown in picture, tighten arm bolt

Arm
Bolt

A7741A

90°

See page 5 for closer
adjustment and cover
installation

A7741A

Copyright © 2008, Sargent Manufacturing Company, an ASSA ABLOY Group
company. All rights reserved. Reproduction in whole or in part without the express
written permission of Sargent Manufacturing Company is prohibited.

A7741A

Choose From 1 of the 3 Applications

JO Standard Arm

JP9 Parallel Arm

JO Top Jamb Arm

Use Standard & Parallel Full Size Templates Provided

Pre-drill - 3/32” holes
for self tapping screws or #16 drill for
#12-24 tap for machine screws

Using optional mortise nuts when through-bolting
Frame
Frame

Door
Doorstop
stop

Mortise
nutnut
Mortise

Power Adjustment
f

Drill 1/4"
dia.
hole Dia.
for hole
screws

Drill 3/8"
Dia.dia.
Drill
3/8"
hole for
mortise
hole
for
mortise
nut
body
nut body

Unreinforced
Unreinforced door
door

A7741A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2008:11:18 11:18:03Z
Creator Tool                    : QuarkXPress(R) 7.31
Modify Date                     : 2009:10:06 10:00:59-04:00
Metadata Date                   : 2009:10:06 10:00:59-04:00
Producer                        : QuarkXPress(R) 7.31
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments
Format                          : application/pdf
Title                           : A7741A
Document ID                     : uuid:5bc2f42a-16bb-4efd-baa2-79bccc6c19ae
Instance ID                     : uuid:273e7f89-5c4e-4014-afb0-874e23d43812
Page Count                      : 8
Creator                         : QuarkXPress(R) 7.31

EXIF Metadata provided by EXIF.tools

Sargent A7741A 1331 Series Door Closer Installation Instructions With JUO (JO & JP9) Arms A7741

Navigation menu

Versions of this User Manual:

Views

Navigation