Sargent A7741A 1331 Series Door Closer Installation Instructions With JUO (JO & JP9) Arms A7741

User Manual: Sargent 1331 Series Door Closer Installation Instructions with JUO (JO & JP9) Arms Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 8

Frame

Unreinforced

door

Door stop

Mortise nut

Drill 3/8" Dia.

hole for mortise

nut body

Dia. hole

f

1

SARGENT®1331 DOOR CLOSER INSTALLATION

INSTRUCTIONS WITH JUO (JO & JP9) ARMS

Strength Adjustable From Size 1 Thru 6

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE

Auxiliary door stop required

FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477 or www.Sargentlock.com

Choose From 1 of the 3 Applications

OR

Pre-drill - 3/32” holes

for self tapping screws or #16 drill for

#12-24 tap for machine screws

Use Standard & Parallel Full Size Templates Provided

JO Standard Arm JP9 Parallel Arm JO Top Jamb Arm

*1/4" Variance allowed for retrofit of existing closers

NOTE: With swing clear hinges, use data sheets provided.

Frame

Door stop

Unreinforced door

Mortise nut

Drill 3/8" dia.

hole for mortise

nut body

Drill 1/4" dia.

hole for screws

8

With fasteners provided, secure closer body to door with power adjust-

ment away from hinge.

Power Adjustment

Using optional mortise nuts when through-bolting

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

2 7

1331 STANDARD APPLICATION JO ARM

INSTALLATION INSTRUCTIONS

Determine maximum degree of door opening required. Use a #16 drill. Drill and tap door and frame for 12-24 machine screws.

When using the included self tapping screw, pre-drill with a 3/32” drill *Provides maximum power for heavy or drafty doors

2

3

45

*(120° - 12")

180° - 10-1/8"

*(120° - 6-12")

180° - 4-5/8"

2" 1"

1-3/8"

12"

3/4"

With provided fasteners, install foot to frame and secure

closer body to door with power adjustment

away from hinge

Right hand shown, left hand similar.

2A

++

Move foot

pivot to hole

nearest hinge

For additional power move foot towards hinge

edge of door

Hinge edge of door

On both right and left hand doors, secure main arm to top spindle

with screw and washer provided. Align flat mark as shown

Open door and insert foot into main arm. Close door fully, and while

pushing arm as shown in picture, tighten arm bolt

See page 5 for closer

adjustment and cover

installation

Power Adjustment

Flat mark

Arm

Bolt 90°

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group

company. All rights reserved. Reproduction in whole or in part without the express

written permission of Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

1

6 3

*(120° - 3-3/4")

180° - 1-1/4"

Center line

of hinge

12"

3-1/2"

3/4"

With fasteners provided, install foot to stop and closer body to

door with power adjustment toward hinge

With wrench on bottom spindle,

preload/index by turning spindle as

shown and secure main arm to top

spindle with flat mark as indicated at

left with screw and washer

1

1331 JP9 PARALLEL ARM INSTRUCTIONS

2

Right hand shown, left hand opposite.

3

4Open door and insert foot into main arm. Close door fully while holding elbow 1-1/4” from door. Tighten arm bolt

5See page 5 for

adjustment and

cover installation

*Provides maximum power for heavy

or drafty doors

1" minimum stop

width required

Accessory Information

2-1/2" Min.

1331D

Drop plate used when

top rail is less than 2 1/2"

Power adjustment

*(120° - 9-12")

180° - 7"

7/16"

2-3/4"

2" 3/8"

3/8"

Center line

of hinge

1-1/4"

Arm Bolt

Left Hand Door Right Hand Door

Flat mark

Determine maximum degree of door opening required. Use a #16

drill. Drill and tap door and frame for 12-24 machine screws.

When using the included self tapping screws, predrill with a 3/32"

drill.

581-1 Blade Stop Spacer Kit

Metal spacer for use on 1/2" blade

stops on aluminum store fronts

Drop Plate

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

4

2

3

1

1331 JO TOP JAMB INSTRUCTIONS

4

5

With provided fasteners, install foot to door and closer body

to frame with power adjustment away from hinge 2A

++

Adjusting foot for additional closing power

Move foot

pivot to hole

nearest hinge

Hinge edge of door

Open door and insert foot into main arm. Close door fully, and while

pushing arm as shown in picture, tighten arm bolt

On both right and left hand doors, secure main arm to top spindle with screw and washer provided. Align flat mark as shown

See page 5 for adjustment and cover installation

Determine maximum degree of door opening required.

Use a #16 drill. Drill and tap door and frame for 12-24

machine screws. When using provided self tapping screws,

predrill with a 3/32" drill

Note: 2" maximum reveal allowed

Right hand shown, left

hand similar

*(120° - 6-7/8")

180° - 4-3/4"

2"

1-7/8"

Power Adjustment

Hinge Edge

3/4" 12"

1/2"

*(120° - 12-3/8")

180° - 10-1/4"

Center line

of hinge

Accessories

Arm

Bolt 90°

Flat mark

5

THE 1331 IS FACTORY ADJUSTED FOR MOST APPLICATIONS, HOWEVER,

ADDITIONAL ADJUSTMENT MAY BE REQUIRED DUE TO ACTUAL CONDITIONS

1/8" HEX wrench

Backcheck

range

Sweep (Closing)

speed range

Latching speed

range

Sweep

Latch

Backcheck

Spring power adjustment

Slow

down

Speed

up

5MINIMUM RECOMMENDED DOOR CLOSING TIME FOR DOORS OPENED TO 90° IS 6 SECONDS.

Use 1/8" hex (Allen) wrench to adjust valves as needed

SWEEP AND LATCHING SPEEDS:

Turn valves clockwise to slow down or counterclockwise to speed up door movement

BACKCHECK:

To regulate the intensity of backcheck action, turn valve clockwise to increase or counterclockwise to decrease checking

CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. CLOSER CAN BE DAMAGED IF THE CHECKING ACTION IS TOO

ABRUPT. NEVER USE THE BACKCHECK AS A DOOR STOP. ALWAYS USE A DOOR STOP TO STOP THE DOOR

IF ADJUSTMENTS ARE INEFFECTIVE, CHECK INDEXING AS SHOWN IN STEP 3 AND CHECK FOR

CORRECT TEMPLATING

1/8"

Cover Installation

Move insert if needed. Install cover with two #6- 32 X 5/16" machine screws as shown

6

Insert

CLOSER ADJUSTMENT AND COVER INSTALLATION

*Provides maximum power for heavy or drafty doors

CLOSING POWER:

Certain applications may require closing power adjustment:

If the door will not latch properly, increase power by turning

the power adjustment clockwise in full turn increments.

If the door is hard to open, reduce power by turning the power

adjustment counter-clockwise in full turn increments.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

4

2

3

1

1331 JO TOP JAMB INSTRUCTIONS

4

5

With provided fasteners, install foot to door and closer body

to frame with power adjustment away from hinge 2A

++

Adjusting foot for additional closing power

Move foot

pivot to hole

nearest hinge

Hinge edge of door

Open door and insert foot into main arm. Close door fully, and while

pushing arm as shown in picture, tighten arm bolt

On both right and left hand doors, secure main arm to top spindle with screw and washer provided. Align flat mark as shown

See page 5 for adjustment and cover installation

Determine maximum degree of door opening required.

Use a #16 drill. Drill and tap door and frame for 12-24

machine screws. When using provided self tapping screws,

predrill with a 3/32" drill

Note: 2" maximum reveal allowed

Right hand shown, left

hand similar

*(120° - 6-7/8")

180° - 4-3/4"

2"

1-7/8"

Power Adjustment

Hinge Edge

3/4" 12"

1/2"

*(120° - 12-3/8")

180° - 10-1/4"

Center line

of hinge

Accessories

Arm

Bolt 90°

Flat mark

5

THE 1331 IS FACTORY ADJUSTED FOR MOST APPLICATIONS, HOWEVER,

ADDITIONAL ADJUSTMENT MAY BE REQUIRED DUE TO ACTUAL CONDITIONS

1/8" HEX wrench

Backcheck

range

Sweep (Closing)

speed range

Latching speed

range

Sweep

Latch

Backcheck

Spring power adjustment

Slow

down

Speed

up

5MINIMUM RECOMMENDED DOOR CLOSING TIME FOR DOORS OPENED TO 90° IS 6 SECONDS.

Use 1/8" hex (Allen) wrench to adjust valves as needed

SWEEP AND LATCHING SPEEDS:

Turn valves clockwise to slow down or counterclockwise to speed up door movement

BACKCHECK:

To regulate the intensity of backcheck action, turn valve clockwise to increase or counterclockwise to decrease checking

CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. CLOSER CAN BE DAMAGED IF THE CHECKING ACTION IS TOO

ABRUPT. NEVER USE THE BACKCHECK AS A DOOR STOP. ALWAYS USE A DOOR STOP TO STOP THE DOOR

IF ADJUSTMENTS ARE INEFFECTIVE, CHECK INDEXING AS SHOWN IN STEP 3 AND CHECK FOR

CORRECT TEMPLATING

1/8"

Cover Installation

Move insert if needed. Install cover with two #6- 32 X 5/16" machine screws as shown

6

Insert

CLOSER ADJUSTMENT AND COVER INSTALLATION

*Provides maximum power for heavy or drafty doors

CLOSING POWER:

Certain applications may require closing power adjustment:

If the door will not latch properly, increase power by turning

the power adjustment clockwise in full turn increments.

If the door is hard to open, reduce power by turning the power

adjustment counter-clockwise in full turn increments.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

6 3

*(120° - 3-3/4")

180° - 1-1/4"

Center line

of hinge

12"

3-1/2"

3/4"

With fasteners provided, install foot to stop and closer body to

door with power adjustment toward hinge

With wrench on bottom spindle,

preload/index by turning spindle as

shown and secure main arm to top

spindle with flat mark as indicated at

left with screw and washer

1

1331 JP9 PARALLEL ARM INSTRUCTIONS

2

Right hand shown, left hand opposite.

3

4Open door and insert foot into main arm. Close door fully while holding elbow 1-1/4” from door. Tighten arm bolt

5See page 5 for

adjustment and

cover installation

*Provides maximum power for heavy

or drafty doors

1" minimum stop

width required

Accessory Information

2-1/2" Min.

1331D

Drop plate used when

top rail is less than 2 1/2"

Power adjustment

*(120° - 9-12")

180° - 7"

7/16"

2-3/4"

2" 3/8"

3/8"

Center line

of hinge

1-1/4"

Arm Bolt

Left Hand Door Right Hand Door

Flat mark

Determine maximum degree of door opening required. Use a #16

drill. Drill and tap door and frame for 12-24 machine screws.

When using the included self tapping screws, predrill with a 3/32"

drill.

581-1 Blade Stop Spacer Kit

Metal spacer for use on 1/2" blade

stops on aluminum store fronts

Drop Plate

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

2 7

1331 STANDARD APPLICATION JO ARM

INSTALLATION INSTRUCTIONS

Determine maximum degree of door opening required. Use a #16 drill. Drill and tap door and frame for 12-24 machine screws.

When using the included self tapping screw, pre-drill with a 3/32” drill *Provides maximum power for heavy or drafty doors

2

3

45

*(120° - 12")

180° - 10-1/8"

*(120° - 6-12")

180° - 4-5/8"

2" 1"

1-3/8"

12"

3/4"

With provided fasteners, install foot to frame and secure

closer body to door with power adjustment

away from hinge

Right hand shown, left hand similar.

2A

++

Move foot

pivot to hole

nearest hinge

For additional power move foot towards hinge

edge of door

Hinge edge of door

On both right and left hand doors, secure main arm to top spindle

with screw and washer provided. Align flat mark as shown

Open door and insert foot into main arm. Close door fully, and while

pushing arm as shown in picture, tighten arm bolt

See page 5 for closer

adjustment and cover

installation

Power Adjustment

Flat mark

Arm

Bolt 90°

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group

company. All rights reserved. Reproduction in whole or in part without the express

written permission of Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

1

Frame

Unreinforced

door

Door stop

Mortise nut

Drill 3/8" Dia.

hole for mortise

nut body

Dia. hole

f

1

SARGENT®1331 DOOR CLOSER INSTALLATION

INSTRUCTIONS WITH JUO (JO & JP9) ARMS

Strength Adjustable From Size 1 Thru 6

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE

Auxiliary door stop required

FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477 or www.Sargentlock.com

Choose From 1 of the 3 Applications

OR

Pre-drill - 3/32” holes

for self tapping screws or #16 drill for

#12-24 tap for machine screws

Use Standard & Parallel Full Size Templates Provided

JO Standard Arm JP9 Parallel Arm JO Top Jamb Arm

*1/4" Variance allowed for retrofit of existing closers

NOTE: With swing clear hinges, use data sheets provided.

Frame

Door stop

Unreinforced door

Mortise nut

Drill 3/8" dia.

hole for mortise

nut body

Drill 1/4" dia.

hole for screws

8

With fasteners provided, secure closer body to door with power adjust-

ment away from hinge.

Power Adjustment

Using optional mortise nuts when through-bolting

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.

A7741A

Copyright ©2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All

rights reserved. Reproduction in whole or in part without the express written permission of

Sargent Manufacturing Company is prohibited.