Sargent Installation Instructions For 281 Door Closers With O10/H10/SSO Arms A7921C

User Manual: Sargent Installation Instructions For 281 Door Closers With O10/H10/SSO Arms Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 4

281 DOOR CLOSERS WITH O10, H10 & SSO ARMS

INSTALLATION INSTRUCTIONS

281 SERIES ADJUSTABLE FROM SIZE 1 THRU 6

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.

FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.

DRILL AND TAP DOOR

AND FRAME FOR #12-

24 MACHINE SCREWS.

RIGHT HAND SHOWN,

LEFT HAND OPPOSITE.

*NOTE: FOR MAXIMUM

POWER, INSTALL FOR

110° OPENING

PULL SIDE PULL SIDE

PUSH SIDE PUSH SIDE

LEFT HAND DOOR RIGHT HAND DOOR

CLOSERS ARE NON-HANDED

ATTACH ARM TO FACE OF FRAME.

B

RIGHT HAND SHOWN

FOR H10 ARM ONLY

C

INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS. MOUNT CLOSER WITH SPRING

ADJUSTING SCREW AWAY FROM HINGE. SEE PAGE 2 FOR THRU BOLT INFO.

1

ALTERNATE: PREASSEMBLE ARM PRIOR TO

ATTACHING TO STOP.

C1

A

Copyright © 2012, 2014, Sargent Manufacturing Company, an ASSA ABLOY

Group company. All rights reserved. Reproduction in whole or in part without

the express written permission of Sargent Manufacturing Company is prohibited.

A7921C

ACCESSORIES

OPTIONAL: USE MORTISE NUTS (#4TB)

WHEN THRU-BOLTING IS REQUIRED

DA. ATTACH ARM WITH INDEX MARK ON SPINDLE

ALIGNED AS SHOWN BELOW

B. SECURE WITH SCREW AND WASHER.

D1

* WARNING: IF NOT PROPERLY INDEXED, DOOR

CLOSER WILL NOT FUNCTION PROPERLY.

!! !!

ALTERNATE METHOD FOR ATTACHING

PREASSEMBLED ARM

281 DROP PLATE USED WITH NARROW TOP RAILS.

EA. INSTALL PIVOT AS SHOWN

B. USE SCREW TO SECURE PIVOT AND ARMS AS SHOWN

2

CLOSER VALVES

Copyright © 2012, 2014, Sargent Manufacturing Company, an ASSA ABLOY

Group company. All rights reserved. Reproduction in whole or in part without

the express written permission of Sargent Manufacturing Company is prohibited.

A7921C

FINAL ADJUSTMENT AND REGULATING PROCEDURES

F

3

HINSTALL COVER WITH TWO SCREWS AS SHOWN.

SSP INCLUDES HANDED METAL COVER

(NOT SHOWN) AND 6 LOBE SECURITY SCREWS.

GAdjust Closing power to the minimum required to reliably

close and latch door

· If door is hard to open, decrease power slightly

· If door does not latch, increase power as required

· Use the chart below as a starting point

Doors adjusted with high closing power to overcome strong

draft conditions may exceed ADA standards

+-

DOOR WIDTH EXTERIOR DOORS *INTERIOR DOORS

(INCHES)

24-30 Turn screw 2-7 Turn screw 1-5

30-36 Turn screw 7-11 Turn screw 3-6

36-42 Turn screw 11-15 FACTORY SET

42-48 Turn screw 15-17 Turn screw 8 & up

SPRING POWER ADJUSTMENT GUIDELINES

INCREASE

POWER

DECREASE

POWER

ADJUST CLOSING

POWER WITH A 1/4"

HEX WRENCH

· Adjust Door speed, and Latching speed valves to

achieve the desired closing time. Recommend 6

seconds minimum from 90° to the closed position.

· If Backcheck is required, adjust valve to achieve a

slight cushioning effect. Auxiliary stop required

· If closer is equipped with Delayed Action, regulate

valve to achieve the desired delay.

USE 1/8" HEX WRENCH

TO ADJUST VALVES

BACKCHECK

RANGE

DELAYED ACTION

RANGE

CLOSING SPEED

RANGE

LATCHING SPEED

RANGE

Copyright © 2012, 2014, Sargent Manufacturing Company, an ASSA ABLOY

Group company. All rights reserved. Reproduction in whole or in part without the

express written permission of Sargent Manufacturing Company is prohibited.

A7921C

4

Copyright © 2012, 2014, Sargent Manufacturing Company, an ASSA ABLOY

Group company. All rights reserved. Reproduction in whole or in part without

the express written permission of Sargent Manufacturing Company is prohibited.

A7921C

4 5/8"

- -

REVISED TABLE DIMENSION "B", 15" WAS 14"

-A

B

ZONE

10/25/13

REV.

REVISIONS

DESCRIPTION DATE APPROVED

ORIGINAL RELEASE PER PCP07-0047

MOUNTING POSITIONS

MAX. DOOR

OPENING DIM. A DIM. B

110 7 1/2" 15-1/2"

160 4 1/2" 11 1/8"

JCN 2/14/07

Form Rev. 28Oct2005

.

100 Sargent Drive New Haven, CT 06511

B

A

C

D

A

B

C

D

1234

1234

DWG No. SH

1:4

UNLESS OTHERWISE SPECIFIED

REV

RELEASE DATE

1

DWG No.

.XX

1/64

1

.01

FRACTION

ANGLE

A7956

TOLERANCE

2-8-07

2-7-07

2-6-07

DE

ST

GPF

BGS

CONFIDENTIAL

8/10/06

CHECKED BY/DATE

B

TITLE:

SIZE

.XXX

SCALE:

.005

100 Sargent Drive New Haven, CT 06511

DOOR CLOSERS

PER ANSI Y14.5M -1994

COMPANY.

REV

MAT'L

ART.

1of 1

C

PROD CTRL/FNL REL

FNL APPROVAL/DATE

INTERPRET DRAWING

WRITTEN PERMISSION OF THE SARGENT MANUFACTURING

ALL DIMENSION ARE IN INCHES.

FNL APPROVAL/DATE

SARGENT Manufacturing Company

SHEET:

MFG ENG/DATE

DRAWN BY/DATE

281 O10/H10 TEMPLATE

A7956

THIS DOCUMENT IS THE CONFIDENTIAL PROPERTY OF

SARGENT MANUFACTURINGAND IS NOT TO BE REPRODUCED,

USED OR DISCLOSED BY ANYONE WITHOUT THE EXPRESS

TEMPLATE NO

Manufacturing Company

GLASS

OR H10 HEAVY DUTY STANDARD ARM

OF HINGE

281 SERIES DOOR CLOSER WITH O10

12 GAUGE MINIMUM REINFORCEMENT REQUIRED ON METAL DOORS AND FRAMES.

281 COVER

NOTES

3.

DOOR WILL OPEN TO 180° IF CLOSER COVER DOES NOT INTERFERE WITH ADJACENT WALL

4.

A 281-J PLATE MAY BE USED WHEN COVER IS VISIBLE THROUGH GLASS

4

FACE OF DOOR

FRAME REINFORCEMENT

FACE OF FRAME

DOOR

REINFORCEMENT

1.

1

281 MOUNTING PLATE

C

L

2. RIGHT HAND DOOR SHOWN, LEFT HAND OPPOSITE

1

COVER

A7956 B

#12-24 x 5/8" FLAT HEAD

MACHINE SCREWS OR #12 X

1 1/2" SCREWS PROVIDED

#12-24 x 3/4" PAN HEAD

MACHINE SCREWS OR #12 X

1 1/2" SCREWS PROVIDED

3

DIM. "B"

DIM "A"

2 7/8"

10 3/8"

1/4"

MIN RAIL

2 3/16"

1"

MAX REVEAL

1 1/4"

2 1/2"

12"

7/8"

13/16"