Satellite Electronic 18002 CEILING FAN REMOTE CONTROLLER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4177047
Application ID	HMZjFyuH9twgsc0tidHeTA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.63kB (245420 bits)
Date Submitted	2019-02-22 00:00:00
Date Available	2019-02-22 00:00:00
Creation Date	2018-12-19 14:38:40
Producing Software	Acrobat Distiller 9.3.2 (Windows)
Document Lastmod	2019-01-09 15:35:09
Document Title	Microsoft Word - TR107E 英文说明书（SWITCH）
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

DC POWER CEILING FAN REMOTE CONTROL MANUAL
LEARNING PROCESS
NOTE: The Hand Held Remote Control System is equipped with a
learning frequency function which has code combinations to prevent
potential interference from other remote units. The frequency on your
Receiver and Transmitter units have been preset at the factory. We
recommend changing the frequency while installing your ceiling fan
instead of using the initial frequency set by the factory (Fig. 1) Please
use a small size tool to change the code switch setting.
Step: 1. Within 30 seconds of turning the Receivers AC power ON.
Press the transmitter’s “ OFF” button.
Step: 2. Hold the “OFF” button for over 4 seconds, once the receiver
has detected the frequency, the receiver will make one sound, Bi and
light flicker twice and turn off,Meanwhile the fan be turn off.This will
indicate the receiver has learned the frequency that was previously
selected on the transmitter.
A:If you would like that the receiver make sound when changing function, you could turn on the sound. The
setting way is that you pressing “OFF” button about 4 seconds when you control the ceiling fan. please note that
when you reboot power.on ,you need to wait after 30 seconds to perform this operation
B:If you don’t need the receiver make sound, you can pressing “OFF” button about 4 seconds when you control
the ceiling fan.please note that when you reboot power.on ,you need to wait after 30 seconds to perform this
operation
Note: After the AC power is on, do not press any other button on the transmitter before pressing the “OFF” button
doing so will cause the procedure to fail.
After completing the steps above, you should be able to operate the ceiling fan and light If the fan is not
responding to the transmitter, please turn the power off to the receiver. And repeat step 1 and 2.
Install the DC1.5V/AAA 2PCS batteries. Remove the batteries if not used for long periods of time to prevent
damage to the hand held remote.
FUNCTIONS OF TRANSMITTER
1.
F/R ：“F/R” BUTTION
shown on LCD : fan wind direction is up
shown on LCD :fan wind direction is down
2.
：“NATURAL FLOW” HI/LOW SPEED SWITCH
shown on LCD :Fan automatically change fan speed to make the natural
wind
3.
FAN ： 1~6 FAN SPEED(Press this button to select desired speed, there are 6
different fan speed, release the button after setting)
shown on LCD :This symbol is full when the fan in HI speed
4. OFF ： To turn the fan off
shown on LCD : turn fan off
5. LIGHT ：To turn on and turn off the light (Light function only for fans with light kit)
shown on LCD : turn light on
shown on LCD : turn light off
6. While Battery power is low as
shown on LCD, please replace new DC1.5V/AAA batteries.
Installation of transmitter wall
mount holder with two screws.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
FCC ID：2AQZU-18002
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : Administrator
Create Date                     : 2018:12:19 14:38:40+08:00
Modify Date                     : 2019:01:09 15:35:09+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2019:01:09 15:35:09+08:00
Format                          : application/pdf
Title                           : Microsoft Word - TR107E 英文说明书（SWITCH）
Creator                         : Administrator
Producer                        : Acrobat Distiller 9.3.2 (Windows)
Document ID                     : uuid:c72f597e-72b4-4b67-92e2-d0318777e31d
Instance ID                     : uuid:e3a97037-5c3d-4639-8ac5-da84fa377a51
Page Count                      : 2

EXIF Metadata provided by EXIF.tools