Savant Technologies GE Lighting a Savant 94440 Wireless Lamp Fixture (433 MHz) User Manual GE telligent Lutron InstructionSheet V2

GE Lighting Wireless Lamp Fixture (433 MHz) GE telligent Lutron InstructionSheet V2

Contents

Instruction

Integrated Dimming
With integrated dimming you can control your
lights without using an in wall dimmer switch. You
can also set moods or scenes by connecting
multiple lights to the same wireless remote.
Your Lutron® Pico® wireless remote is pre-paired to
work with the GE telligent™ LED lamp with
integrated dimming. See instructions to pair
multiple lights with a single remote.
For more wireless remote set up and information
on, tabletop pedestals, faceplates, and mounting
adaptors, visit lutron.com/ picoremote.
Instructions and Setup
Dims to off
Brightens
Dims
Brightens to
full intensity
Tap once:
Adjusts to
favorite level
Press and hold
for 6 seconds:
Saves new
favorite level
Remote Control
10-year battery life
30 feet or more wireless range
OPTIONAL: How to control multiple light bulbs.
To pair additional telligent™ LED light bulbs with this remote control.
No Setup Required
Remote and LED in package are pre-paired.
Simply keep the light switch on and remote will work at any time. The remote will not work if
the light switch connected to the lamp is turned off.
1 2 3
Repeat these steps to pair additional light bulbs.
Control up to 10 GE telligent™ LEDs with 1 remote.
x3
3 seconds
Turn off the light
bulb with the
light switch and
wait 3 seconds.
The battery in this device contains Perchlorate material, special handling may apply.
For more information visit www.dtsc.ca.gov/hazardouswaste/perchlorate.
Turn on the
light bulb with
the light switch.
Immediately press and hold the bottom
button on the remote control until the
light bulb flashes 3 times.
OFF ON
The GE telligent lamp will turn on to full
brightness every time power is applied. For
example, turning the lamp off then on with a
light switch will turn the lamp on to full
brightness.
Programming of multiple
Lutron Pico remotes with
GE telligent™ LED lamps
Lutron Pico® remotes can be paired to any
number of GE telligent™ LED lamps within
range of the RF signal (at least 30 feet,
through most walls and floors). All lamps
will be controlled together by the paired
Pico® remote. For Pico® remotes with a
“Favorite” button, different paired lamps
can be programmed to different levels to
create a “scene”. This can be done by
following a simple procedure:
1. Ensure all lamps are paired to the
selected Pico® remote following the
provided procedure.
2. Unscrew or turn off power to all but one
paired lamp. Use the raise and lower
buttons on the Pico® remote until the
desired light level is reached for that
lamp. Press and hold the Favorite button
until the lamp acknowledges the light
level is saved.
3. Unscrew or remove power from the
just-programmed lamp, and apply power to
the next lamp. Repeat the raise/lower/save
procedure for the second lamp.
4. Repeat the procedure, applying power to
one single lamp at a time and saving the
light levels until all lamps have a Favorite
light level saved.
When power is reapplied to all lamps,
pressing the Favorite button will cause
them all to go to their different saved levels.
Note: all lamps paired to a Pico® remote
will go to a Favorite light level; lamps
cannot have an “unaffected” Favorite
level. Lamps can have different Favorite
light levels for each paired Pico® remote.
Un-pairing a Pico® remote from a
lamp
Following this procedure will prevent the
Pico® remote from controlling any lamps
associated with it. Note that lamps must
be powered on (but do not need to be
turned on) and within wireless range. All
programmed lamps should be powered on
for at least 30 seconds before starting this
procedure!
Press the Off button on the remote three
times within one second.
Hold the Off button for five seconds, until
the green LED on the Pico® remote turns on.
Press the Off button on the remote
three more times within one second. Any
associated lamps which are turned on and
within range will no longer be controlled
by the Pico® remote.
Restoring a lamp to its factory
default settings
This procedure will cause the lamp to no
longer be associated with ANY Pico®
remotes (including any that were
factory-paired in the same package). A
Pico® remote will need to be re-paired
with a lamp before the lamp can be
controlled again. All Favorite light levels
will also be lost.
To restore a lamp to its factory-default
settings, and clear all programming, follow
the “Un-pairing a Pico® remote from a
lamp” procedure within the first 30
seconds of a lamp powering up using an
already-paired Pico® remote. If successful
the lamp will flash three times, return to
full brightness, and the Pico® remote will
no longer control the lamp.
1.
2.
3.

Navigation menu