Savi Technology 673T-V1 RF ID Tag User Manual Savi Sensor Tag ST673 ST674 InstallGuide

Savi Technology Inc RF ID Tag Savi Sensor Tag ST673 ST674 InstallGuide

Users Manual Part 3

CHAPTER 2Installing the Tag18 Savi SensorTag ST-673 Installation GuideNote:You receive the Savi SensorTag ST-673 and metal mounting sleeve fully assembled. You can skip step 1 through step 6 to mount the unit to the jet engine container or you can follow the instructions in step 1 through step 6 if you disassembled the tag and mounting sleeve.1. Remove the front of the mounting sleeve.2. Slide the tag into the mounting sleeve until the holes on the tag align with the holes on the back of the mounting sleeve.3. Replace the front of the mounting sleeve.4. Align the hole on the front of the mounting sleeve with the holes on the tag and back of the mounting sleeve.
Mounting Savi SensorTag ST-673Savi SensorTag ST-673 Installation Guide 195. To prevent the tag from dislodging from the tag mounting sleeve as a result of sudden impact or extreme shocks, use the supplied stainless steel screws and washers through the sleeve.6. Ensure that you can see the sensor filter through the hole on the back of the mounting sleeve.7. Carefully remove the red protective film covering from the PST on the back of the sleeve. Avoid touching the PST adhesive.Use supplied screws to washers to secure the tag to the sleeve
CHAPTER 2Installing the Tag20 Savi SensorTag ST-673 Installation Guide8. Open the jet engine container and locate the humidity detection orifice.9. Unscrew the nut on the mounting sleeve.Humidity detection orifice
Mounting Savi SensorTag ST-673Savi SensorTag ST-673 Installation Guide 2110.Remove the small rubber gasket washer from the mounting sleeve.11.To mount the tag, insert the mounting sleeve and tag in the humidity detection orifice.12.Apply pressure to the tape strips by pushing firmly against the tag. To assure a good bond, apply as much finger pressure as possible and work fingers up and down the area over the tape strips.
CHAPTER 2Installing the Tag22 Savi SensorTag ST-673 Installation Guide13.On the inside of the container, replace the small rubber gasket washer and screw the nut on the mounting sleeve to secure the tag. Close the jet engine container.14.If the orifice of the container is too large for the tag to be mounted securely, insert a metal shoulder washer before replacing the rubber washer and nut. Ensure that the lip on the metal shoulder washer is inserted through the orifice and is facing the outside of the container.The metal shoulder washer must be ordered separately.Mounted tag
APPENDIX ASavi SensorTag ST-673 Installation Guide 23Savi SensorTag ST-673 SpecificationsASpecification DescriptionPhysical characteristics Length: 6 .25 inches (16 cm)Width: 2.13 inches (5.4 cm)Height: 1.13 inches (2.9 cm)Weight: 3.8 oz. (108 g)Environment Temperature: -40ºF to +158ºF (-40ºC to +70ºC) operating; -40ºF to +185ºF (-40ºC to +85ºC) storage; Tested per MIL-STD-810FHumidity: 100% non-condensingAltitude: Maximum altitude = 40,000 feet (12,192m); Tested per MIL-STD-810FRF receiver/transmitter Ultra High Frequency transceiver:Frequency: 433.92 MHzModulation: FSK, deviation +/- 50KHzData rate: 27.8KbpsData coding: ManchesterCommunication range (unobstructed): Typical range is up to 300 feet (91.44 meters) line-of-sight when mounted onto a container and communicating with a Savi Fixed Reader SR-650-101 or SaviReader 410R. Typical range is 200 feet (61 meters) line-of-sight when communicating with a Savi MobileReader SMR-650Maximum transmit power: 0.6mWAir protocol: BCS Commands, EBCS Commands (20-bit and 22-bit tag identification supported); Savi EchoPoint Air Protocol 2.1 (32-bit tag identification supported)
APPENDIX ASavi SensorTag ST-673 Specifications24 Savi SensorTag ST-673 Installation GuideLF receiver (downlink) Low Frequency Receiver (downlink)Frequency: 123 KHzModulation: ASK on-off keyingData rate: Average 1.6 Kbps, 50% duty cycleData coding: Pulse width modulationCommunication range: Up to 3.5 feet (1 meter) from Savi Mobile Reader SMR-650. Up to 12 feet (3.66 meters) from Savi Signpost SP-651 and SP-652-211Air protocol: BCS Commands, EBCS Commands (22-bit tag identification supported); Savi EchoPoint Air Protocol 2.1 (32-bit tag identification supported) and Savi EchoPoint Air Protocol 1.1Network Wireless: RF read/write capableMemory On board non-volatile 128K user memory for all tags and 32K sensor memoryHardware compatibility ✦Savi Mobile Reader SMR-650P (model SMR-650P-110 and SMR-650P-111)✦Savi Mobile Reader SMR-650 (models SMR-650-21x)✦Savi Fixed Reader SR-650-101✦Savi Signpost SP 651 and SP-652✦Savi Docking Station model SDS-2002✦Savi ST-654 Docking Station Adapter SDSA-654-01✦Savi Tag Write Cable STA-1030✦Savi Tag Write Cable Adapter STA-1031Antenna Internal UHF: Omni loop antennaInternal LF: Two integrated ferrite core antennas (orthogonally mounted)Shock and vibration Shock: Tested per MIL-STD-810F, 4 feet (1.22 meters)Vibration: Tested per MIL-STD-810F Protection type Sealed to IP 54ISO 1496 weatherproofing requirementsSpecification Description
Savi SensorTag ST-673 Installation Guide 25Power Battery type: 3.6 volt primary lithium (Li-SOCI2), A size, user replaceableBattery life: Approximately 4 years depending on usagePower management: UHF sleep mode prevents unwanted collections, enabled/disabled by LF linkDiagnostics: Reports low tag battery statusRegulatory approvals Radiated emission (intentional): U.S. emission standards as contained in FCC Part 15 and European Community emission standards as contained in EN 300 220 (433 MHz)Electromagnetic immunity: ESD compliance exposed to 8 kV air discharge or 4 kV contact discharge in accordance with EN 301 489-1Radiated emission (unintentional): U.S. emissions standards as contained in FCC Part 15 and European Community emission standards as contained in EN 301 489-1Safety approval: U.S UL 1950; European EN 60950Ordnance Safety: HERO certificationMarkings: Savi logo, product model and serial number, EMC compliance (FCC/EN), and Ordnance/HEROSensors and indicators Temperature sensor: Integrated sensor takes temperature readings based on configurable time (in minutes). Default is set to 5 minutesHumidity sensor: Integrated humidity sensor takes readings based on configurable time (in minutes). Default is set to 5 minutesBeeper: Audible beeper for tag location.Mounting Metal mounting sleeve with screws and PST for SensorTag ST-673Software Savi SmartChain for Mobile Devices, Savi SmartChain Transportation Security System (TSS), Savi SmartChain Site Manager 5.7, Savi SmartChain Client Tools 4.x, Savi SmartChain Mobile Manager 6.x, Savi Retriever 2.1Accessories Spare A size batteries; part number BAT-1125Specification Description
APPENDIX ASavi SensorTag ST-673 Specifications26 Savi SensorTag ST-673 Installation Guide

Navigation menu