Scheidt and Bachmann PITBASETWN4 RFID Hitag Reader User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3433301
Application ID	enkB2UEUHTwMm9lUIJu/wQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	105.15kB (1314337 bits)
Date Submitted	2017-06-21 00:00:00
Date Available	2017-06-21 00:00:00
Creation Date	2017-04-03 09:42:59
Producing Software	Acrobat Distiller 10.0.0 (Windows)
Document Lastmod	2017-06-20 14:43:12
Document Title	Microsoft Word - MODULE_USER_PitBase-TWN4_8693421_a_0_en_GB.docx
Document Creator	PDF-T-Maker 3jg088b - 14 July 2011
Document Author:	Schiffer.Peter

PitBase with TWN4
Component Description
Language:
Article No.:
QM:
English
86 93421 (a)
D-Q-S
© Scheidt & Bachmann GmbH
Parking and access systems
Breite Strasse 132
41238 Moenchengladbach
Germany
www.scheidt-bachmann.com
Subject to change
Author: Peter Schiffer
Modification log:
Refer to chapter "Record of Revisions"
entervo and the entervo logo are trademarks of the Scheidt & Bachmann GmbH.
This manual including all of its segments is protected by copyright. Scheidt & Bachmann GmbH reserves all rights in its contents. Any utilization not approved expressly
by the copyright law is subject to prior agreement by Scheidt & Bachmann GmbH. This
applies particularly to copying, processing, translations, microfilming as well as storage and data processing in any electronic systems.
Since all information and facts are subject to technical changes, any liability for the
data contained is hereby disclaimed. Modifications of technical details, in terms of information and illustrations are reserved. Make sure to follow the updating index.
Scheidt & Bachmann GmbH cannot be made responsible for direct damage and/or
possible consequential damage due to maloperation of the product by the customer or
by third parties, unless the Product Liability Act (ProdHaftG) is concerned.
© 2015 Scheidt & Bachmann GmbH, Germany
Parking and access systems
Breite Straße 132
41238 Moenchengladbach
www.scheidt-bachmann.com
Subject to change.
Contents
Introduction .......................................................... 6
1.1
Range of Application ............................................ 6
1.2
Safety .................................................................. 6
Module Description ................................................ 7
2.1
Block Diagram ..................................................... 8
2.2
Antenna Connection ............................................ 9
2.3
FCC Information ................................................ 10
2.4
FCC Label ........................................................... 11
2.5
Technical Specifications..................................... 11
Disposal .............................................................. 12
Index .................................................................. 13
Document History................................................ 14
Notes................................................................... 15
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
Subject to change
PitBase TWN4, 86 93421 (a)
1
I n tro du ct io n
This manual describes the ChipCoin read/write module PitBase TWN4 with the
S&B article no. 04 38882 0.
Fig. 1: PitBase TWN4
1.1
Range of Application
The PitBase TWN4 is a hardware interface for encoding and evaluation of
HITAG based ChipCoins and transponder cards.
PitBase TWN4 is used exclusively in Scheidt & Bachmann devices.
1.2
Safety
Electrostatically endangered parts! Do not touch connection points!
Installed components may contain electrostatically endangered parts (ESD).
When working on the module, please take measures to protect against ESD!
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
Subject to change
PitBase TWN4, 86 93421 (a)
2
Modu le De s cr ip tion
Components
 TWN4 Core-Module (Elatec)
 S&B base board
The PitBase TWN4 has a power connector, a serial interface for the connection
of a single board computer (EPR) or a manual sales device and two antenna
connectors.
Fig. 2: PitBase TWN4 – top with the cover removed
Fig. 3: PitBase TWN4 - bottom
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
Subject to change
PitBase TWN4, 86 93421 (a)
Fig. 4: RS232 interface and power connector
2.1
Fig. 5: Antenna connectors
Block Diagram
Power
Antenna 2
TWN4
Core Module
Antenna 1
Host Interface
RS232
DSUB
RS232
Fig. 6: Block diagram
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
Subject to change
PitBase TWN4, 86 93421 (a)
2.2
Antenna Connection
ST2
ST1
Fig: Antenna connection
There are 7 connection options for the two antenna connectors.
If antennas are connected to both antenna connectors, an automatically
cycled switching between both connectors takes place (e.g. every 5 seconds
/ configurable).
Connection option 1:
Connection terminal ST1: 1 x antenna 0420830 0 (air-core coil 30x30 490μH)
Connection terminal ST2: not used
Connection option 2:
Connection terminal ST1: 1 x antenna 0423652 0 (air-core coil 30x30 490μH)
Connection terminal ST2: not used
Connection option 3:
Connection terminal ST1: 1 x antenna 0434483 0 (air-core coil 30x60 490μH)
Connection terminal ST2: not used
Connection option 4:
Connection terminal ST1: 1 x antenna 04378230 (air-core coil 30x60 490μH)
Connection terminal ST2: not used
Connection option 5:
Connection terminal ST1: 1 x antenna 0423652 0 (air-core coil 30x30 490μH)
Connection terminal ST2: 1 x antenna 04184530 (air-core coil Ø30 490μH)
Connection option 6:
Connection terminal ST1: 1 x antenna 0420830 0 (air-core coil 30x30 490μH)
Connection terminal ST2: 2 x antenna 0418532 0 connected in parallel (aircore coil Ø30 980μH)
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
Subject to change
PitBase TWN4, 86 93421 (a)
Connection option 7:
Connection terminal ST1: 2 x antenna 0431701 0 connected in parallel (aircore coil 30x30 980μH)
Connection terminal ST2: not used
2.3
FCC Information
FCC ADDENDUM
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
IC-CANADA-ADDENDUM
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
10
Subject to change
PitBase TWN4, 86 93421 (a)
2.4
FCC Label
The FCC label on the PCB provides information on the approval number:
Fig. 7: PitBase TWN4 – FCC Label
FCC ID: O5K-PITBASETWN4 / IC: 8312A-PITBASETWN4
The device that contains the PitBase TWN4 must contain the following wording in its user manual:
Contains FCC ID: O5K-PITBASETWN4
Contains IC: 8312A-PITBASETWN4
2.5
Technical Specifications
General technical data
Supported media:
 HITAG-1 transponder (125 kHz)
 HITAG-S2048 transponder (125 kHz)
Connectors:
 2 x antenna coil
 Power connection via 3.5mm jack connector
 RS232 interface
Operating voltage:
12 V DC ± 20 %
Current consumption:
approx. 100 mA
Read/write antennas:
 2 connectors
 Inductance: 490μH per connector
 approx. 3 cm read/write distance
Dimensions:
approx. 165 mm x 87 mm x 20 mm
Weight:
approx. 158 g
Temperature range:
-25°C to +80°C
Relative humidity:
±0 % ... 95 % (non-condensing)
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
11
Subject to change
PitBase TWN4, 86 93421 (a)
3
D isp osa l
Packaging materials must be disposed of according to local regulations.
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of
its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Disposing of batteries into household garbage is not permitted; you
are bound by law to return used batteries. Used batteries can contain harmful substances which can damage the environment or your
health when not disposed of correctly. Batteries also contain important commodities such as iron, zinc, manganese or nickel which
will be recycled. You may send the used batteries back to us, or you
can return them to your local recycling center free of charge (recommended). The symbol of the crossed waste container is a warning against disposing of hazardous materials into household garbage.
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
12
Subject to change
PitBase TWN4, 86 93421 (a)
4
Index
Air-core coil 9, 10
Antenna Connection 9
Introduction 6
Notes 15
Batteries 12
Block Diagram 8
Operating voltage 11
Components 7
Connectors 11
Current consumption 11
Packaging materials 12
PCB 11
Dimensions 11
Disposal 12
Document History 14
Relative humidity 11
RS232 interface 8, 11
Elatec 7
Environment 12
EPR 7
ESD 6
Safety 6
Supported media 11
Technical specifications 11
Temperature range 11
TWN4 6, 7, 11
TWN4 Core-Module 7
FCC 10, 11
Hazardous materials 12
HITAG 6
HITAG-1 11
HITAG-S2048 11
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
Weight 11
13
Subject to change
PitBase TWN4, 86 93421 (a)
5
Do cum ent Histo ry
Version
Date
Modification
Author
09/18/2015
Creation
P. Schiffer
04/03/2017
FCC Statement updated
P. Schiffer
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
14
Subject to change
PitBase TWN4, 86 93421 (a)
6
Notes
© 2015 Scheidt & Bachmann GmbH, Germany
Component Description
15
Subject to change
PitBase TWN4, 86 93421 (a)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : Schiffer.Peter
Create Date                     : 2017:04:03 09:42:59+02:00
Modify Date                     : 2017:06:20 14:43:12+02:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PDF-T-Maker 3jg088b - 14 July 2011
Metadata Date                   : 2017:06:20 14:43:12+02:00
Format                          : application/pdf
Title                           : Microsoft Word - MODULE_USER_PitBase-TWN4_8693421_a_0_en_GB.docx
Creator                         : Schiffer.Peter
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Document ID                     : uuid:63f5b2a0-0f90-49b4-9620-2ef7592a81fd
Instance ID                     : uuid:92563330-0b06-4abd-a7f2-583f5d232f11
Page Layout                     : SinglePage
Page Mode                       : UseOutlines
Page Count                      : 15

EXIF Metadata provided by EXIF.tools