Schneider Electric 33950 Wireless RF Key Fob User Manual C Bus RF Wireless Key Fob and Visor Remote

Download:
Mirror Download [FCC.gov]
Document ID	1388604
Application ID	h85vVYBsvKpctUl/Ea1+hA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.8kB (310062 bits)
Date Submitted	2010-12-09 00:00:00
Date Available	2010-12-09 00:00:00
Creation Date	2010-06-29 17:35:58
Producing Software	Acrobat Distiller 9.3.2 (Windows)
Document Lastmod	2010-06-29 17:36:04
Document Title	C-Busâ„¢ RF Wireless Key Fob and Visor Remote
Document Creator	Acrobat PDFMaker 9.1 for Word
Document Author:	06/2010

C-Bus™ RF Wireless Key Fob and Visor Remote
SLC5800TXBDKF and SLC5800TXBDVR for use with
RF Wireless Control Systems
Instruction Bulletin
Retain for future use.
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
63249-420-342A1
06/2010
HAZARD CATEGORIES AND SPECIAL SYMBOLS
Read these instructions carefully and look at the equipment to become
familiar with the device before trying to install, operate, service, or maintain
it. The following special messages may appear throughout this bulletin or on
the equipment to warn of potential hazards or to call attention to information
that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label
indicates that an electrical hazard exists which will result in personal injury if
the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
Danger indicates an immediately hazardous situation which, if not
avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not
avoided, can result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not
avoided, can result in minor or moderate injury.
Caution, used without the safety alert symbol, indicates a potentially
hazardous situation which, if not avoided, can result in property
damage or improper operation.
NOTE: Provides additional information to clarify or simplify a procedure.
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained
only by qualified personnel. This document is not intended as an instruction
manual for untrained persons. No responsibility is assumed by Schneider
Electric for any consequences arising out of the use of this manual.
FCC CLASS B
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:



Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications to this device that are not expressly
approved by Schneider Electric could void the user's authority to
operate this equipment.
© 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
63249-420-342A1
06/2010
ABOUT THE RF KEY FOB AND VISOR REMOTE
The C-Bus™ Wireless RF Key Fob and Visor Remote provides
C-Bus protocol commands to remotely controlled buttons on RF
wireless wall units and plug adapter units.
The two radio frequency (RF) remote controls work up to 50 to 70
feet (15 to 20 meters) from a unit they control. Unlike an infrared
remote, which operates on line-of-sight, an RF remote signal cannot
be blocked by obstructions. The user can control a unit by pointing a
remote in any direction, including away from the unit.
Up to three separate wall units or plug adapter buttons can be
controlled by a remote control unit. The buttons can be on various
units on different wireless networks. A single button on a wall unit or
plug adapter unit can be controlled by up to two RF remote controls.
Before You Begin
Before using the key fob and visor remote, inspect it carefully. Verify
the catalog number on the box label.
Table 1: Contents of the Box
Part Number
Description
Quantity
SLC5800TXBDVR
RF Wireless Visor Remote Control
SLC5800TXBDKF
RF Wireless Key Fob
REMOTE CONTROL BUTTONS
KEY:
Buttons A, B, and C
are individual
programmable control
buttons. Each button
controls a wall unit or
a plug adapter button.
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
INSTALLING THE BATTERIES
Battery Tips and Precautions






Use new CR2032 batteries and verify that all batteries are the
same type.
Keep batteries out of the reach of children.
Verify that the positive (+) and negative (–) battery polarities line
up with the battery-case polarities.
Replace batteries that have been in use two or more years.
Recycle or properly dispose of used batteries.
Try changing the batteries if your remote does not control units.
The remote’s range decreases when the batteries’ power is low.
NOTE: The Short name will not lose programmed data when the
batteries are replaced.
FIRE OR CHEMICAL HAZARD
The batteries used in this unit may present a risk of fire or chemical
burn if not handled properly.

Do not recharge, disassemble, heat above 212 °F (100 °C), or
incinerate.

Recycle or properly dispose of used batteries.

Replace with identical type.
 Follow all battery manufacturers' instructions.
Failure to follow these instructions can result in injury or
equipment damage.
© 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
63249-420-342A1
06/2010
Key Fob Battery Installation
1. Using a small flat-head screw driver, gently pry off the bottom of
the key fob.
2. Remove the old battery from the key fob.
3. Insert the new battery. Verify that the positive and negative
terminals match the symbols inside the battery compartment.
4. Replace the back cover by positioning the cover and snapping it
into place.
Figure 1: Removing the Key Fob Battery
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
Visor Remote Battery Installation
1. Using a small Phillips screw driver, remove the two screws from
the back of the visor remote.
2. Remove the back of the visor remote.
3. Remove the old battery from the visor remote.
4. Insert the new battery. Verify that the positive and negative
terminals match the symbols inside the battery compartment.
5. Replace the back cover by positioning the cover and snapping it
into place.
6. Tighten the screws on the back of the visor remote.
Figure 2: Removing the Visor Remote Battery
© 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
63249-420-342A1
06/2010
PROGRAMMING THE KEY FOB
Follow the guidelines below to make the Key Fob functional.

Program C-Bus Wireless units to recognize the key fob's
buttons.
 Program the key fob, wall units, and plug adapter units using
learn mode.
Learn mode is activated on the remote by removing the back cover
(see the "Installing the Batteries" section to remove the back cover),
and sliding the switch down to the Learn position. Refer to the steps
below to activate learn mode and to program the key fob.
Use the following procedure to assign a button on the key fob to a
button on a C-Bus Wireless wall unit or plug adapter unit:
NOTE: Assigning a button on the key fob to a button on a C-Bus
Wireless unit does not unlearn previous assignments to other units.
To do this, follow the instructions in the "Clearing Remote
Assignments" section.
1. Set the key fob to learn mode by sliding the switch across to
the Learn position.
2. Replace the back cover.
3. On the wall unit, press the Learn button to activate learn mode.
4. On the key fob, press the button you want to assign.
5. Quickly press the button on the wall unit you want the key fob
to control (within 30 seconds of pressing the remote button).
NOTE: All units on the network will enter Learn mode at this
time.
6. Repeat steps 4 and 5 to program additional buttons.
7. When you have finished programming the key fob buttons,
press the learn button on the wall unit to exit learn mode.
8. Remove the back cover on the key fob, slide the learn mode
switch on the back to the Use position, then replace the back
cover.
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
PROGRAMMING THE VISOR REMOTE
Follow the guidelines below to make the Visor Remote functional.

Program C-Bus Wireless units to recognize the visor remote's
buttons.
 Program the visor remote, wall units, and plug adapter units
using learn mode.
Learn mode is activated on the remote by removing the back cover
(see the "Installing the Batteries" section to remove the back cover),
and sliding the switch down to the Learn position. Refer to the steps
below to activate learn mode and to program the visor remote.
Use the following procedure to assign a button on the visor remote
to a button on a C-Bus Wireless wall unit or plug adapter unit:
NOTE: Assigning a button on the visor remote to a button on a
C-Bus Wireless unit does not unlearn previous assignments to
other units. To do this, follow the instructions in the "Clearing
Remote Assignments" section.
1. Set the visor remote to learn mode by sliding the switch across
to the Learn position.
2. Replace the back cover.
3. On the wall unit, press the Learn button to activate learn mode.
4. On the visor remote, press the button you want to assign.
5. Quickly press the button on the wall unit you want the visor
remote to control (within 30 seconds of pressing the remote
button).
NOTE: All units on the network will enter Learn mode at this
time.
6. Repeat steps 4 and 5 to program additional buttons.
7. When you have finished programming the visor remote buttons,
press the learn button on the wall unit to exit learn mode.
8. Remove the back cover on the visor remote, slide the learn
mode switch on the back to the Use position, then replace the
back cover.
© 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
63249-420-342A1
06/2010
CLEARING REMOTE ASSIGNMENTS
To clear an individual remote assignment learned by a specific
button on a wall unit or plug adapter unit, reassign the same remote
button to the wall unit or plug adapter button. Assigning a button
once programs it. Assigning it again clears it.
To clear all remote assignments (from all remote controls) learned
by an individual wall unit or plug adapter unit:
1. Set the remote control to learn mode by sliding the switch across
to the Learn position.
2. On the wall unit or plug adapter unit, press the learn button to
activate learn mode.
3. Press one of the assignable buttons on the remote control.
4. Press twice one of the buttons on the wall unit or plug adapter
unit.
5. Wait until the indicator lights on the wall unit return to a slow
alternating flash. Then press the learn button on the wall unit or
plug adapter to exit learn mode.
6. Slide the learn mode switch on the back to the Use position.
10
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
SPECIFICATIONS
Parameter
Description
Supply voltage
CR2032 batteries
Radio frequency
916 MHz
Transmitting power
10 mW
Wood frame / brick veneer construction
Typical range (range depends
on building construction and the 50 to 70 feet (15 to 20 m)
proximity to dense or metallic
Brick, stone, or steel frame construction
objects)
35 to 50 feet (10 to 15 m)
Steel reinforced concrete construction
20 to 35 feet (5 to 10 m)
Maximum range (open air)
165 feet (50 m)
Operating temperature range
32 to 104 °F (0 to 40 °C)
Operating humidity range
10 to 95% RH
© 2010 Schneider Electric. All Rights Reserved.
11
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
63249-420-342A1
06/2010
DIMENSIONS
Figure 3: Key Fob Dimensions
Figure 4: Visor Remote Dimensions
12
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
STANDARDS
The key fob and visor remote complies with the following Standards:
Table 2: U.S. and Canadian Product Safety Standards and U.S.
FCC Regulations
Standards/Regulations
FCC Part 15
© 2010 Schneider Electric. All Rights Reserved.
Title
Class B Digital Device for Home or Office Use
13
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
14
63249-420-342A1
06/2010
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010
© 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
15
C-Bus™ RF Wireless Key Fob and Visor Remote
Instruction Bulletin
SUPPORT AND SERVICE
Contact the Customer Information Center for technical support by
phone at 1-888-778-2733 or e-mail at
lightingcontrol.support@us.schneider-electric.com.
Contact your local Schneider Electric service representative or
C-Bus™ system certified installer for repairs or service to your
network.
You may also find helpful information on our web site at
www.Schneider-Electric.us.
Schneider Electric, USA
320 Tech Park Drive, Suite 100
La Vergne, TN, 37086
1-888-778-2733
www.schneider-electric.us
C-Bus, Saturn and Neo are trademarks or registered trademarks of
Schneider Electric and/or its affiliates in the United States and/or other
countries.
Electrical equipment should be installed, operated, serviced, and
maintained only by qualified personnel. No responsibility is assumed by
Schneider Electric for any consequences arising out of the use of this
material.
© 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1
06/2010

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Modify Date                     : 2010:06:29 17:36:04-05:00
Create Date                     : 2010:06:29 17:35:58-05:00
Metadata Date                   : 2010:06:29 17:36:04-05:00
Producer                        : Acrobat Distiller 9.3.2 (Windows)
Format                          : application/pdf
Creator                         : 06/2010
Title                           : C-Bus™ RF Wireless Key Fob and Visor Remote
Description                     : Instruction Bulletin
Document ID                     : uuid:91764ead-9ccf-41f6-b140-b22e1e51c599
Instance ID                     : uuid:8bc1dde3-f71f-4189-aebe-bfce327d41fc
Subject                         : 28
Company                         : Square D Company
Manager                         : SLC5800TXBDKF and SLC5800TXBDVR for use with RF Wireless Control Systems
Comments                        : 
Source Modified                 : D:20100629221437
Headline                        : Instruction Bulletin
Page Layout                     : OneColumn
Page Count                      : 16
Author                          : 06/2010
Keywords                        : 63249-420-342A1

EXIF Metadata provided by EXIF.tools