Schneider Electric Weather Radio Ion7550 Users Manual PowerLogic / ION7650 Installation Guide

ION7650 to the manual f3d05de6-4626-4231-92bb-2385f84acfb1

2015-02-06

: Schneider-Electric Schneider-Electric-Weather-Radio-Ion7550-Users-Manual-526989 schneider-electric-weather-radio-ion7550-users-manual-526989 schneider-electric pdf

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

PowerLogic® ION7550 / ION7650
Energy & Power Quality Meter
Installation Guide
December 2007

PowerLogic ION7550 / ION7650 Installation Guide

Danger
This symbol indicates the presence of dangerous voltage within and outside the product enclosure
that may constitute a risk of electric shock, serious injury or death to persons if proper precautions
are not followed.

Caution
This symbol alerts the user to the presence of hazards that may cause minor or moderate injury to
persons, damage to property or damage to the device itself, if proper precautions are not followed.

Note
This symbol directs the user’s attention to important installation, operating and maintenance
instructions.

Installation Considerations
Installation and maintenance of the PowerLogic ION7550 / ION7650 meter should only be performed by qualified,
competent personnel that have appropriate training and experience with high voltage and current devices. The meter
must be installed in accordance with all local and national electrical codes.

DANGER
Failure to observe the following instructions may result in severe injury or death.

During normal operation of the ION7550 / ION7650 meter, hazardous voltages are present on its termi-

nal strips, and throughout the connected potential transformer (PT), current transformer (CT), digital (status) input, control power and external I/O circuits. PT and CT secondary circuits are capable of generating
lethal voltages and currents with their primary circuit energized. Follow standard safety precautions while
performing any installation or service work (i.e. removing PT fuses, shorting CT secondaries, etc.).
The terminal strips on the meter base should not be user-accessible after installation.
Do not use digital output devices for primary protection functions. These include applications where the
devices perform energy limiting functions or provide protection of people from injury. Do not use the
ION7550 / ION7650 in situations where failure of the devices can cause injury or death, or cause sufficient energy to be released that can start a fire. The meter can be used for secondary protection functions.
Do not HIPOT/Dielectric test the digital (status) inputs, digital outputs, or communications terminals. Refer
to the label on the ION7550 / ION7650 meter for the maximum voltage level the device can
withstand.

CAUTION
Observe the following instructions, or permanent damage to the meter may occur.
The ION7550 / ION7650 meter offers a range of hardware options that affect input ratings. The

ION7550 / ION7650 meter’s serial number label lists all equipped options. Applying current levels incom-

patible with the current inputs will permanently damage the meter. This document provides installation
instructions applicable to each hardware option.
The ION7550 / ION7650 meter’s chassis ground must be properly connected to the switchgear earth
ground for the noise and surge protection circuitry to function correctly. Failure to do so will void the
warranty.
Terminal screw torque: Barrier-type (current, voltage, and relay terminal screws: 1.35 Nm (1.00 ft-lbf)
max. Captured-wire type (digital inputs/outputs, communications, power supply: 0.90 Nm

(0.66 ft.lbf) max.

FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.

PowerLogic ION7550 / ION7650 Installation Guide

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
The Ringer Equivalence Number (REN) for the ION7550 / ION7650 optional internal modem is 0.6. Connection to
the ION7550 / ION7650 internal modem should be made via an FCC Part 68 compliant telephone cord (not
supplied). The ION7550 / ION7650 cannot be used on a public coin phone service or party line services.

Network Compatibility Notice for the Internal Modem
The internal modem in meters equipped with this option is compatible with the telephone systems of most countries
in the world. Use in some countries may require modification of the internal modem’s initialization strings. If problems
using the modem on your phone system occur, please contact Schneider Electric Technical Support.

Standards Compliance

CSA: Certified to CAN/ Certified to
CSA C22.2 No.1010-1 UL 3111
Made by Power Measurement Ltd.
PowerLogic, ION, ION Enterprise, MeterM@il, WebMeter and Modbus are either trademarks or registered
trademarks of Schneider Electric.
Covered by one or more of the following patents:
U.S. Patent No's 7010438, 7006934, 6990395, 6988182, 6988025, 6983211, 6961641, 6957158,
6944555, 6871150, 6853978, 6825776, 6813571, 6798191, 6798190, 6792364, 6792337, 6751562,
6745138, 6737855, 6694270, 6687627, 6671654, 6671635, 6615147, 6611922, 6611773, 6563697,
6493644, 6397155, 6236949, 6186842, 6185508, 6000034, 5995911, 5828576, 5736847, 5650936,
D505087, D459259, D458863, D443541, D439535, D435471, D432934, D429655, D427533.

PowerLogic ION7550 / ION7650 Installation Guide

PowerLogic ION7550 / ION7650 Models
Integrated Display Model
Comes with front optical port.

TRAN (transducer) Model
The TRAN model has no display.

Available Options
Option

ION7550

Form Factor

Current Inputs

Integ. Display
TRAN
5 MB memory
10 MB memory
Up to 256
sampling rate

Standard

Standard (RS-232,

1 Amp

Ethernet RJ45
Ethernet Fiber
Modem

(5 Amp)

Power Supply

COM
RS-485, optical)

Standard
Low Voltage

Model

Form Factor

Current Inputs

Integ. Display
Same as
ION7550
TRAN
5 MB memory
Power Supply
10 MB memory
Same as
Up to 512
ION7550
sampling rate
(standard)
1024 sampling
rate (optional)
EN50160
compliance
IEC61000-4-30
Class A
compliance

ION7650

COM
Same as

ION7550

I/O
Standard (8 digital

inputs, 3 Form C relays,
4 Form A outputs)
Extra 8 digital inputs
Four 0-1mA analog
inputs
Four 0-20 mA analog
inputs
Four -1 to 1mA analog
outputs
Four 0-20 mA analog
outputs

I/O
Same as ION7550

Security
Standard1
RMANSI2

Security
Same as

ION7550

Notes
1

Standard = password protected, no locking or sealing.

RMANSI = ANSI C12.16 approved revenue meter; meets ANSI C12.20
class 0.2 accuracy standards.

PowerLogic ION7550 / ION7650 Installation Guide

Before You Begin
Before installing the meter, familiarize yourself with the steps in this guide and
read the safety precautions presented on the “Installation Considerations”
page.

DANGER
Do not power up the meter until the current and voltage wiring is completed.

Recommended Tools

Phillips screwdriver
Precision flat-head screwdriver
Wire cutters / stripper

Meter Overview
Meter Front

Meter Back
Voltage and Current Inputs

Digital Inputs

Softkeys
ESC

Button

Optical Port

Navigation
Buttons

Analog Outputs

I/O Expansion
Card

Power
Supply

Operational
LEDs

Analog Inputs

PROG/SELECT

Button

Communications
Card

Form C
Digital Outputs

Digital
Inputs

Ground
Terminal

Form A
Digital Outputs

Front Panel Button Functions
PROG

PROG/SELECT: Press the PROG/SELECT (program or select) button to enter Setup
mode. In Setup mode, press the PROG/SELECT button to accept changes.

Press the ESC (Escape) button to return to a higher menu or discontinue a
configuration change.

ESC:
ESC

Press the UP / DOWN arrow buttons to highlight menu items, or
increment / decrement numbers.

NAVIGATION:

Press the LEFT or RIGHT arrow buttons to move to an adjacent digit.
SOFTKEY: Press a SOFTKEY button to select the parameter that you want to
configure from the sub-menus.

PowerLogic ION7550 / ION7650 Installation Guide

Unit Dimensions
Basic Model — Rear View

Basic Model — Front View

Basic Model — Side View

PowerLogic ION7550 / ION7650 Installation Guide

Step 1: Mount the Meter
Environmental Specifications
Mounting Location
Operating Range
Display Operating Range
Storage Range
Relative Humidity Range

Indoor use
-20 to +70ºC (-4 to +158ºF) Standard Power Supply
-20 to +50ºC (-4 to +122ºF) Low Voltage DC Power Supply
No formation of ice
-20 to +70ºC (-4 to +158ºF)
-40 to +85ºC (-40 to +185ºF)
5 to 95% non-condensing

Meter Battery Considerations
The meter’s battery life expectancy depends on both temperature and the
amount of time the meter is without power. For typical installations, the
battery should last 20 years or more. If the meter is not powered, the battery
will last a minimum of 7 years at room temperature.

Integrated Display Model
1.

Fit the meter into the DIN standard 192 cutout (186 mm by 186 mm).

Slide the four brackets into their slots on the back of the meter and secure
using the four Phillips head screws. Do not overtighten.
Screw

DIN 192
Cutout

Bracket

Step 2: Wire the Ground Terminal
Connect the
terminal to a good earth ground with a 2.1 mm2 (14 AWG)
wire. Ensure that the terminal nut is tightened down securely onto the ground
wire. Do not use metal door hinges as a grounding point.

PowerLogic ION7550 / ION7650 Installation Guide

Step 3: Wire the Digital I/O and Analog I/O
Form C Digital Outputs: Mechanical Relays R1 - R3
Internal Form C
Mechanical
Relay

R11

R13
R12

R11 R12 R13 R21

Type
Contacts
Wire
Connector
Voltage Rating
Rated Load @
Rated Voltage
Max. Voltage
MOV Protection
Max. Load @
Max. Voltage
Turn-On Time
Isolation
Turn-Off Time

Form C (R1, R2, R3)
K (common), Y (NO), Z (NC)
Use wiring that is appropriate for the application
Ring or split ring connector
250 VAC / 30 VDC
Resistive: 10 A (AC/DC)
Inductive (PF=0.4): 7.5 A (AC) / 5 A (DC)
380 VAC / 125 VDC between K and NO/NC
300 V max. between NO and NC
3 A (AC) / 0.2 A (DC)
15 ms max.
5,000 VAC for 60 s
5 ms max.
No load = 10,000,000 operations
Rated voltage and load = 100,000 operations
½ cycle or 1 s

Lifetime
Update time

Meter

Mechanical
relays should
always be
protected by
external fuses

Load

Alarm Lamp

External Supply

Form A Digital Outputs: Solid State Relays D1 - D4
Form A (D1, D2, D3, D4)

Wire

1.3 to 0.1 mm2 (16 to 28 AWG)
Continuous or pulse
30 VDC
80 mA per channel
Optically isolated; max. 5,000 V RMS isolation
(UL-E91231)
½ cycle or 1 s

Signal Type
Max. Load Voltage
Max. Load Current
Isolation
Scan Time

Meter

D1
- +

_
+

1.8 Wh

D2
- +

D3
- +

DIGITAL OUTPUTS
D4
- +

Internal Form A
Solid State Relay

Type

External
Relays

External Supply
30VDC max
D4 output is factory-configured to pulse once every 1.8 Wh for Class 20 meters,
or once every 0.18 Wh for Class 2 meters (for calibration testing purposes).
© 2007 Schneider Electric. All rights reserved.

PowerLogic ION7550 / ION7650 Installation Guide

Digital Inputs: S1 - S8
DIGITAL INPUTS
S
C
O
M

S S
8 7

S
6

S S
5 4

S
3

S
2

S
1

Type
Application

Self-excited (internal 30 VDC supply)
Dry contact sensing, or with external excitation

Wire

1.3 to 0.1 mm2 (16 to 28 AWG)
1 ms
20 pulses per second
1 ms
½ cycle (after timing resolution)
max. 200 VDC for 10s
130 VDC continuous

Min. Pulse Width
Max. Pulse Rate
Timing Resolution
Updated
Isolation to Ground
Max. External Voltage

Internal Excitation

External Excitation

Meter

_
S7

_
+

_
S8

30 VDC
+
SCOM

Opticallycoupled switch

30 VDC
+
+

SCOM

Opticallycoupled switch

External Supply

130 VDC max

Digital Inputs (Meter Ordering Option): DI1 - DI8
Type
Application

Self excited (internal 30 VDC supply)
Dry contact sensing, or with external excitation

Wire
Min. Pulse Width
Max. Pulse Rate
Timing Resolution
Updated
Isolation to Ground
Max. External Voltage

1.3 to 0.1 mm2 (16 to 28 AWG)
20 ms
25 pulses per second
2 ms
½ cycle (after timing resolution)
750 VDC
50 VDC continuous

Internal Excitation
Meter

External Excitation
Meter

Opticallycoupled switch

External Supply

50 VDC max

PowerLogic ION7550 / ION7650 Installation Guide

Analog Inputs (Meter Ordering Option): AI1 to AI4
AI3

AI3

Captured wire connector

Wire

1.3 to 0.1 mm2 (16 to 28 AWG)
DC current

Signal Type

+ -

AI4

Type

AI2 AI1

Available Options

0 to 20 mA (scalable 4-20 mA) or 0 to 1 mA

Input Impedance
Accuracy
Update Rate
Isolation to Ground
Isolation Impedance

24 Ω (0-20 mA option) or 475 Ω (0-1 mA option)
+/– 0.3% of full scale
1s
750 V
max 400 kΩ (channel/channel)

Thermocoupler

Voltage-toCurrent
Transducer

Meter
+
AI1

Example
application:
temperature
sensing

NOTE
Do not connect the analog inputs of the I/O card to the analog outputs on
the same I/O card.

Analog Outputs (Meter Ordering Option): AO1 to AO4
AO3

OUT COM

Type

Captured wire connector

Wire

1.3 to 0.1 mm2 (16 to 28 AWG)
DC current
0 to 20 mA (scalable 4-20 mA) or -1 to 1 mA
(scalable 0-1 mA)
500 Ω (0-20 mA option) or 10 kΩ (-1 to 1 mA
option)
+/– 0.30% of full scale
½ cycle or 1 s
min. 1 cycle for measurement + ½ cycle for ION
+ 1 s delay for hardware
750 V

Signal Type
Available Options
Driving Capability

AO4 A03 A02 AO1

Accuracy
Update Rate
Latency
Isolation to Ground

Meter
Analog
Meter

OUT

AO1

Example application: driving an
analog meter with the DC
current output

COM

NOTE
Do not connect the analog outputs of the I/O card to the analog inputs on
the same I/O card.

PowerLogic ION7550 / ION7650 Installation Guide

Step 4: Wire the Voltage and Current Inputs
V1

V2 V3 V4 Vref I11 I12 I21

3~ VOLTAGE INPUTS

I22 I31 I32 I41 I42

I51 I52

3~ CURRENT INPUTS

Voltage Inputs
Connector Type

Ring or split ring connector

Wire Gauge

3.3 to 2.1 mm2 (12 to 14 AWG)
347 V L-N RMS /600 V L-L RMS
1200 V L-N peak
1500 VAC RMS continuous
2500 VAC RMS at 60 Hz for 60 s
5 MΩ/phase (phase - Vref)

Rated Inputs
Fault Capture
Overload
Dielectric Withstand
Input Impedance

Current Inputs: Class 20 Current Inputs (5A Option)
Connector Type
Wire Gauge
Input Rating
Starting Current
Fault Capture
Max. Voltage
Overload
Dielectric Withstand
Burden
Impedance

Ring or split ring connector
5.3 to 3.3 mm2 (10 to 12 AWG):
Use 8.4 mm2 (8 AWG) for 10-20 A applications
5 A, 10 A, and/or 20 A RMS
0.005 A RMS
70 A peak
600 V RMS (CAT III IEC61010-1)
500 A RMS for 1 s, non-recurring
2500 VAC RMS at 60 Hz for 60 s
0.05 VA per phase (at 5 A)
0.002 Ω per phase

Current Inputs: Class 2 Current Inputs (1A Option)
Connector Type

Ring or split ring connector

Wire Gauge

5.3 to 3.3 mm2 (10 to 12 AWG)
1 A, 2 A, 5 A, and/or 10 A RMS
0.001 A RMS
17.5 A peak
600 V RMS (CAT III IEC61010-1)
50 A RMS for 1s, non-recurring
2500 VAC RMS at 60 Hz for 60 s
0.015 VA per phase (at 1 A)
0.015 Ω per phase

Input Rating
Starting Current
Fault Capture
Max. Voltage
Overload
Dielectric Withstand
Burden
Impedance

NOTE
The appropriate Volts Mode setting is included with each wiring diagram.
Refer to Step 8 to learn how to configure Volts Mode on the meter.

PowerLogic ION7550 / ION7650 Installation Guide

4-Wire Wye, 3-Element, Direct Connection Diagram
LOAD

LINE

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

I4 Optional

347 V L-N / 600 V L-L max.
VOLTS MODE = 4W-Wye

4-Wire Wye, 3-Element, 3 PTs Connection Diagram
LOAD

LINE

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

I4 Optional

Use PTs for voltages over 347 V L-N / 600 V L-L.
Wye (Star) wiring for PT primaries and secondaries.
VOLTS MODE = 4W-Wye

4-Wire Wye, 2½-Element, 2 PTs Connection
LOAD

LINE

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

I4 Optional

Phase B voltage (V2) displayed by meter is derived from phase A and
phase C, not measured. V2 will display a value even if no voltage is
present on Phase B. V2 values are only accurate for balanced loads.
VOLTS MODE = 3W-Wye

PowerLogic ION7550 / ION7650 Installation Guide

3-Wire Solid-Grounded Wye, 3-Element, Direct Connection
LOAD

LINE

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

When the common or star point of a 3-wire Wye system is grounded,
the meter may be connected directly without using PTs, provided that the
phase voltages are within the meter’s range.
VOLTS MODE = 4W-Wye

3-Wire Delta, 2½-Element, Direct Connection
LOAD

LINE

A
B
C

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

3A
Do not
connect

V2 V3 V4 Vref I11 I12 I21 I22 I31 I32 I41 I42 I51 I52

L / + N/-

600 V L-L max.
VOLTS MODE = Delta

3-Wire Delta, 2-Element 2 PTs & 2 CTs
LOAD

LINE

A
B
C

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

V2 V3 V4 Vref I11 I12 I21 I22 I31 I32 I41 I42 I51 I52

L / + N/-

Use PTs for voltages over 600 V L-L.
VOLTS MODE = Delta

PowerLogic ION7550 / ION7650 Installation Guide

3-Wire Delta, 2½-Element, 2 PTs & 3 CTs
LOAD

LINE

A
B
C

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

V2 V3 V4 Vref I11 I12 I21 I22 I31 I32 I41 I42 I51 I52

L / + N/-

Use PTs for voltages over 600 V L-L
VOLTS MODE = Delta

Single Phase Connection Diagram
LOAD

LINE

Fuse for N/- terminal
required if its supply
source is ungrounded
Connect G terminal
to ground for AC
power source

I4 Optional

277 V L-N / 554 V L-L max. Use PTs for higher voltages.
VOLTS MODE = Single

Using Potential Transformers
System Mode
Wye

Single Phase
Delta

Voltage Range
120 V L-N or 208 V L-L
277 V L-N or 480 V L-L
347 V L-N or 600 V L-L
over 347 V L-N or 600 V L-L
120 V L-N or 240 V L-L
277 V L-N or 554 V L-L
over 277 V L-N or 554 V L-L
up to 600 V L-L
over 600 V L-L

Requires PTs
no
no
no
yes
no
no
yes
no
yes

PowerLogic ION7550 / ION7650 Installation Guide

Step 5: Wire the Communications
RS-232 Connections (COM1)
DB9 Null Modem
Wiring Diagram

DTE
(computer)

Specification

DTE
(meter)

Meter Connected to Computer

Connector Type
Wire
Maximum Cable Length
Data Rate
Isolation
Duplex
Compliance

Null modem cable pinout
Pin 3 - Transmit Data - Pin 2
Pin 2 - Receive Data - Pin 3
Pin 7 - Request to Send- Pin 8
Pin 8 - Clear to Send- Pin 7
Pin 5 - Signal Ground- Pin 5
Pin 6 - Data Set Ready- Pin 4
Pin 4 - Data Terminal Ready- Pin 6

Meter Connected to External
Modem

DB9 female end for mating with male connector on the meter
Null modem RS-232 cable
Straight-through RS-232 cable
15.2 m (50 ft)
300 – 115,200 bps
Optical
Full
ANSI/IEEE C37.90.1-2002 surge withstand and fast transient tests

RS-485 Connections (COM1 and COM2)
SH
–
+

RS-485 Shield (electrically connected to chassis ground)
RS-485 Data Minus
RS-485 Data Plus

Connector Type
Wire
Maximum Cable Length
Data Rate
Maximum Devices (per bus)
Isolation
Duplex
Connect SH at
one end only

Compliance

Captured wire
Shielded twisted pair RS-485 cable,
0.33 mm2 (22 AWG) or larger
1219 m (4000 ft) total for entire bus
300 – 115,200 bps
32
Optical
Half
ANSI/IEEE C37.90.1-2002 surge withstand
and fast transient tests

Infrared Connections (COM4)
Interface
Location
Data Rate
Duplex

ANSI C12.18 Type II optical port
Front of meter
1,200 – 19,200 bps
Half

PowerLogic ION7550 / ION7650 Installation Guide

Ethernet Connections (if equipped)
10BASE-T / 100BASE-TX
Pin 1: Transmit Data +
Pin 2: Transmit Data Pin 3: Receive Data +
Pin 6: Receive Data -

Wire Type
Connector Type
Maximum Length

High quality Category 5 or 6 unshielded twisted pair cable
RJ45 modular
100 m (328 ft)
IEEE 802.3 10/100BASE-T for 10/100 Mbps base band CSMA/CD
Type
LANs
Data Rate
10/100 Mbps
Isolation
Transformer isolated to 1500 V RMS
Max. Connections Allowed 4 simultaneous (32 via Modbus TCP/IP)

100BASE-FX (Fiber)
62.5/125 or 50/125 micrometer multimode fiber optic
cable
Connector Type
SC
2000 m (6562 ft) full duplex
Maximum Length
400 m (1312 ft) half duplex
Data Rate
100 Mbps
Isolation
Optical
Wire Type

SC type fiber cable

Ethernet TCP/IP Service Ports
Protocol

Only one EtherGate
connection per port
is allowed at a time

Port
7700
7701
502
7801
7802
20,000
25 (configurable)

ION
Modbus RTU
Modbus TCP
EtherGate (COM1)
EtherGate (COM2)
DNP TCP
SMTP

Internal Modem Connection (COM3 if equipped)
Pin 3: Ring
Pin 4: Tip

Connector Type
Wire Type
Data Rate
Error Correction
Data Compression

RJ11
FCC Part 68 compliant telephone cord (two male
RJ11 ends)
300 bps – 56 kbps
V.42 LAPM, MNP 2-4, V.44
V.42 bis/MNP 5

PowerLogic ION7550 / ION7650 Installation Guide

Step 6: Wire the Power Supply
Specification

G L+ N_

Standard Power Supply

Type

Captured wire connector

Wire

3.3-2.1 mm2 (12-14 AWG)

Low Voltage DC
2.1-0.8 mm2 (14-18 AWG)

85-240 VAC ±10% (47-63 Hz),
20-60 VDC ±10%
or 110-300 VDC ±10%
Dielectric Withstand 2500 VAC RMS at 60 Hz for 60s
Burden
35 VA max. (15 VA typical)
18 W max. (12 W typical)
Ride-through
100 ms (6 cycles at 60 Hz) min. None

Rated Inputs

Step 7: Power Up the Meter
1.

Ensure the ground wire is securely connected on both ends.

Ensure the meter’s power supply voltage is within the allowed range.

Power up the meter.

Step 8: Set Up the Meter Using the Front Panel
The following Setup screens are available for meter configuration via the
front panel:
BASIC SETUP
COM1 SETUP
COM2 SETUP
COM3 SETUP
COM4 SETUP
NETWORK SETUP
PQ SETUP
FORMAT SETUP
DISPLAY SETUP
TIME SETUP
SECURITY SETUP
METER RESETS

Use the PROG/SELECT, ESC, softkeys and arrow buttons to configure settings.
The following example shows Volts Mode setup using the meter front panel.

Press
Press
Press

Press
Press

Press PROG/SELECT to
enter Setup Mode
from Display Mode.

Press

Use arrow buttons to
move up and down in
list. Press PROG/SELECT
to select Basic Setup.

Use arrow buttons to
move up and down in
list. Press PROG/SELECT
to select PT/CT Setup.

Press Mode softkey.
Use arrow buttons to
move up and down in
list. Press PROG/SELECT
to select Delta.

PowerLogic ION7550 / ION7650 Installation Guide

Password
A password is required for all front panel configuration changes and to enter
the Security Setup menu. The password is set to 0 (zero) in the factory. The
front panel only prompts you for the meter password once, before you make
your first configuration change. You can disable the password via the Security
Setup menu.

Selecting the Front Panel Language
Meters are shipped with English as the default front panel language.
To select another language:
1.

Press PROG/SELECT and the right arrow buttons, hold for two seconds
then release.

Scroll through the language list and select the language you want.

Press PROG/SELECT to confirm.

You can also access this setting via the Display Setup menu.

NOTE
The meter only communicates to software in English.

PowerLogic ION7550 / ION7650 Installation Guide

Front Panel Setup Menu Settings
The following table lists all settings that can be configured via the front panel.

BASIC SETUP

Setting

Description

Default

VOLTS MODE

4W-WYE

PT PRIMARY

The Potential Transformer’s primary
1 to 999,999.99
winding voltage rating

120.00

PT SECONDARY

The Potential Transformer’s
secondary winding voltage rating

1 to 999,999.99

120.00

CT PRIMARY

The Current Transformer’s primary
winding current rating

1 to 999,999.99

5.00

CT SECONDARY

The Current Transformer’s
secondary winding current rating

1 to 999,999.99

5.00

V4 PRIMARY

The Potential Transformer’s primary
1 to 999,999.99
winding voltage rating on V4

120.00

V4 SECONDARY

The Potential Transformer’s
secondary winding voltage rating
on V4

1 to 999,999.99

120.00

I4 PRIMARY

The Current Transformer’s primary
winding current rating on I4

1 to 999,999.99

5.00

I4 SECONDARY

The Current Transformer’s
secondary winding current rating
on I4

1 to 999,999.99

5.00

I5 PRIMARY

The Current Transformer’s primary
winding current rating on I5

1 to 999,999.99

5.00

I5 SECONDARY

The Current Transformer’s
secondary winding current rating
on I5

1 to 999,999.99

5.00

V NOMINAL

The V1, V2 and V3 nominal voltage
1.000 to 999,999.000
used for harmonics calculations

120.00

V4 NOMINAL

The V4 nominal voltage used for
harmonics calculations

1.000 to 999,999.000

120.00

Va POLARITY

The polarity of the Potential
Transformer on Va

Normal or Inverted

Normal

Vb POLARITY

The polarity of the Potential
Transformer on Vb

Normal or Inverted

Normal

Vc POLARITY

The polarity of the Potential
Transformer on Vc

Normal or Inverted

Normal

V4 POLARITY

The polarity of the Potential
Transformer on V4

Normal or Inverted

Normal

Ia POLARITY

The polarity of the Current
Transformer on Ia

Normal or Inverted

Normal

Ib POLARITY

The polarity of the Current
Transformer on Ib

Normal or Inverted

Normal

Ic POLARITY

The polarity of the Current
Transformer on Ic

Normal or Inverted

Normal

I4 POLARITY

The polarity of the Current
Transformer on I4

Normal or Inverted

Normal

I5 POLARITY

The polarity of the Current
Transformer on I5

Normal or Inverted

Normal

CURRENT PROBE The type of current probes being
TYPE
used with the meter

Range (Values)

The power system’s configuration – 4W-WYE, DELTA, 3W-WYE,
WYE, DELTA, etc.
SINGLE, DEMO

Factory Default, User Defined 1, Factory
or User Defined 2
Default

PowerLogic ION7550 / ION7650 Installation Guide

COM1 SETUP

Setting

Description

COM2 SETUP
COM3 SETUP

Default

PROTOCOL

The communications protocol

BAUD RATE

The data rate, in bits per second

3001, 1200, 2400, 4800, 9600, 19,200
19200, 38400, 57600, 115200

TRAN DELAY

The transmit delay in seconds

0 to 1

UNIT ID

Every meter on an RS-485 network
1 to 9999
must have a unique Unit ID number

0.010
From serial
number2

SERIAL PORT

Parity and stop bits for the port

8N1, 8N2, 8E1, 8E2, 8O1, 8O2 8N1

MODE

Hardware mode for the port

RS232 or RS485

RS232

RTS + DELAY or RTS/CTS

RTS +
DELAY

Specifies the handshake mode
FLOW CONTROL
when COM1 is set to RS232

COM4 SETUP

Range (Values)

ION, Modbus RTU, Modbus
Master, DNP V3.00,
ION
GPS:Truetime/Datum,GPS:
Arbiter, GPS:Arbiter-Vorne,
Factory, Ethergate, ModemGate

RS485 BIAS

Turns on biasing when Mastering
on the RS-485 bus

ON or OFF

OFF

PROTOCOL

The communications protocol

See COM1 protocol

ION

The data rate, in bits per second

3001, 1200, 2400, 4800, 9600,

19,200

0 to 1

0.010

BAUD RATE

19200, 38400, 57600, 115200

TRAN DELAY

The transmit delay in seconds

UNIT ID

Every meter on an RS-485 network
1 to 9999
must have a unique Unit ID number

SERIAL PORT

Parity and stop bits for the port

8N1, 8N2, 8E1, 8E2, 8O1, 8O2 8N1

RS485 BIAS

Turns on biasing when Mastering
on the RS-485 bus

ON or OFF

OFF

PROTOCOL

The communications protocol

ION, Modbus RTU, Modbus
Master, DNP V3.00,
GPS:Truetime/Datum,GPS:
Arbiter, GPS:Arbiter-Vorne,
Factory

ION

BAUD RATE

The data rate, in bits per second

3001, 1200, 2400, 4800, 9600, 19,200
19200, 38400, 57600, 115200

TRAN DELAY

The transmit delay in seconds

0 to 1

UNIT ID

Every meter on an RS-485 network
1 to 9999
must have a unique Unit ID number

102

ANSWER HR
RINGS

The number of rings during defined
0 to 255
answer hours

NON-ANSWER
HR RINGS

The number of rings during defined
0 to 255
non-answer hours

101

0.010

PROTOCOL

The communications protocol

ION, Modbus RTU, DNP V3.00,
Factory

BAUD RATE

The data rate, in bits per second

1200, 2400, 4800, 9600,
19200

9600

TRAN DELAY

The transmit delay in seconds

0 to 1

0.010

UNIT ID

Every meter on an RS-485 network
1 to 9999
must have a unique Unit ID number

SERIAL PORT

Parity and stop bits for the port

ION

103

8N1, 8N2, 8E1, 8E2, 8O1, 8O2 8N1

PowerLogic ION7550 / ION7650 Installation Guide

NETWORK SETUP

Setting

Description

PQ SETUP
FORMAT SETUP

Default

IP ADDRESS

Sets the IP address for the meter

SUBNET MASK

Used if subnetting applies to your
network

000.000.000.000 to
999.999.999.999

255.240.0.0

GATEWAY

Used in multiple network
configurations

000.000.000.000 to
999.999.999.999

0.0.0.0

DNS PRIMARY

Sets the address for the primary
DNS Server that is configured to
resolve domain names

000.000.000.000 to
999.999.999.999

none

DNS
SECONDARY

Sets the address for the secondary
DNS Server that is configured to
resolve domain names

000.000.000.000 to
999.999.999.999

none

10/100BT
CONFIG

Sets the BASE-T Ethernet max. link
speed and duplexing

Auto, 10BT half, 10BT full,
100BTX half, 100BTX full

Auto

Full Duplex or Half Duplex

Full Duplex

100BFX CONFIG Sets the Fiber Ethernet duplexing

Range (Values)
000.000.000.000 to
999.999.999.999

varies3

SNMP SERVER

Determines whether SNMP protocol
Enabled or Disabled
is enabled on the meter or not

Disabled

SWELL LIMIT

Specifies the magnitude above
which an input must rise for a swell 100 to 1000
to be recorded

106

SAG LIMIT

Specifies the magnitude below
which an input must fall for a sag to 0 to 100
be recorded

CHANGE
CRITERIA

Specifies the amount by which an
input must change during a
0 to 100
disturbance to be considered a new
sub-disturbance

NOMINAL
VOLTAGE4

Specifies the nominal voltage of the
0 to 1,000,000
power system

EVENT PRIORITY

Assigns a priority level to sag/swell
events

0 to 255

200

DIGIT GROUP

Specifies symbols used to delimit
thousands & decimal place holder

1000.0 or 1,000.0 or 1000,0

1000.0

VOLTS DECIMAL

Number of decimal places
displayed for voltages

1. to 123456789.XXX

1.XX

CURRNT
DECIMAL

Number of decimal places
displayed for currents

1. to 123456789.XXX

1.XXX

POWER DECIMAL

Number of decimal places
1. to 123456789.XXX
displayed for power measurements

1.XXX

MEAS SYMBOL

Specifies the convention used for
displaying measurements

IEEE or IEC

IEEE

PHASE LABEL

Specifies how phases are labelled

ABC, RST, XYZ, RYB, RWB, 123

ABC

PF SIGN

Specifies the power factor sign
convention used

IEEE or IEC

IEEE

PF SYMBOL

Sets how power factor is labelled
(LD = leading/LG = lagging)

LD/LG, +/-, CAP/IND

LD/LG

DATE FORMAT

Specifies how dates are displayed

MM/DD/YYYY, DD/MM/YYYY,
YYYY/MM/DD

MM/DD/
YYYY

TIME FORMAT

Specifies whether time is displayed
12 H or 24 H
in 12 hour or 24 hour clock format

24 H

DISPLAY DST

Specifies whether or not DST is
displayed

Yes

Yes or No

PowerLogic ION7550 / ION7650 Installation Guide

Setting

Description

SECURITY
SETUP

TIME SETUP

DISPLAY
SETUP

UPDATE RATE

Range (Values)

Default

Sets when the display updates

1 to 6 (seconds)

CONTRAST

Higher numbers are sharper

0 to 9

DELTA VECTORS

Specifies how vector diagrams are
displayed when in Delta mode

System or Instrument

System

LANGUAGE

Specifies the language used on the
meter’s front panel

English, Spanish, French,
Russian

English

TZ OFFSET

Sets the time zone of the meter’s
location, relative to UTC

- 12:00 to +13:00

+00:00

DST OFFSET

Sets the daylight savings time offset
-3:00 to +3:00
of the meter’s location

+00:00

SYNC SOURCE

Sets the port to receive time
synchronization signals

Ethernet, COM1, COM2,
COM3, COM4

COM1

SYNC TYPE

Specifies whether time sync signals
are received in local time or UTC

Local Time or UTC

UTC

CLOCK SOURCE Specifies time sync source

Internal, Line Freq or COMM

Line Freq

LOCAL DATE

Sets the local date

Same as Date Format setting

LOCAL TIME

Sets the local time

PASSWORD

Sets the meter password

00000000 to 99999999

00000000

ENABLED

Enables or disables meter security

Yes or No

WEB CONFIG

Enables or disables web browser
configuration of the meter

Enabled or Disabled

Enabled

WEB ACTIVE

Enables or disables internal web
server on the meter

Yes or No

Yes

A baud rate of 300 bps is only intended for paging applications.

Serial number = PA-0302B222-01, Unit ID = 2222

Default IP ADDRESS = 172.16.xxx.xxx, where the last two bytes (decimal)
match the last two bytes of the meter’s MAC address (hex).

NOMINAL VOLTAGE must be set to your system’s nominal voltage to
activate the meter’s power quality features.

Step 9: Verify Meter Operation
The LEDs on the back of the meter flash during communications.
LED

Color

Function

Ethernet 100 (Speed)

Green

Off = link at 10 Mb, On = link at 100 Mb

Ethernet TX

Green

Blinking indicates Ethernet transmission

Ethernet RX/LINK

Green

On = link up, Off = link down
Blinking indicates Ethernet reception

Modem DCD

Green

Indicates a carrier signal is detected (active
connection to the modem)

Modem RI

Green

Indicates a ring is detected by the modem

COM3 (Modem) TX

Yellow

Indicates serial transmission on COM3

COM3 (Modem) RX

Yellow

Indicates serial reception on COM3

COM2 TX

Yellow

Indicates serial transmission on COM2

COM2 RX

Yellow

Indicates serial reception on COM2

COM1 TX

Yellow

Indicates serial transmission on COM1

COM1 RX

Yellow

Indicates serial reception on COM1

PowerLogic ION7550 / ION7650 Installation Guide

The LEDs on the front panel indicate the following:
Top (green) LED indicates the meter is operational. The light
should always remain on when the meter is in service.
Middle (red) LED is a watt-hour pulser. During normal
operations this LED should blink intermittently as the meter
measures power.

Watt-hour
pulsing

Bottom (red) LED is user programmable. It can be used for
Alarm notification. See the ION7550 / ION7650 User
Guide for more information.

Front Panel

Phasor Diagrams
You can also view the meter’s phasor diagram in real time. Use the Phasor
Viewer available in PowerLogic ION Setup v2.1 and later (free download
from the PowerLogic website) to verify your meter’s wiring. See the ION Setup
online help for details.

NOTE
The following DELTA phasor diagrams are represented in System mode view.

DELTA phasors for UNITY Power Factor (resistive load)
Applicable Volts Mode = DELTA
VBC

VCA
IC

ACB Rotation

ABC Rotation

VAB

IA
VAB

IC
VBC

VCA

PowerLogic ION7550 / ION7650 Installation Guide

WYE - ABC Rotation
Applicable Volts Mode = 4W-WYE and 3W-WYE

VA
IA

Q1: Lagging PF (-)
VC

Rotation

Reactive Power

+kVAR

Q2: Leading PF (+)

VA
IB

Active Power

+kW

-kW
Q3: Lagging PF (-)

Q4: Leading PF (+)

-kVAR

Rotation

Reactive Power

Rotation

WYE - ACB Rotation
Applicable Volts Mode = 4W-WYE and 3W-WYE

VA
IA

Q1: Lagging PF (-)
VB

Rotation

Reactive Power

+kVAR

Q2: Leading PF (+)

VA
IC

Active Power

+kW

-kW
Q3: Lagging PF (-)

Q4: Leading PF (+)

-kVAR

Rotation

Reactive Power

Rotation

IA
VA

IC
VC

PowerLogic ION7550 / ION7650 Installation Guide

2 Element (3Wire) DELTA - ABC Rotation
Applicable Volts Mode = DELTA

VCA
IB

VAB
IA

Q1: Lagging PF (-)
VCA
IC
Rotation

Rotation

Reactive Power

+kVAR

Q2: Leading PF (+)

IB
VAB

IA
VBC

VBC

Active Power

Active Power
+kW

-kW
Q3: Lagging PF (-)

Q4: Leading PF (+)
VCA

VCA
IA

-kVAR

VBC

Rotation

Reactive Power

Rotation

VAB

IB
VBC

2 Element (3Wire) DELTA - ACB Rotation
Applicable Volts Mode = DELTA

IB
VAB

Q1: Lagging PF (-)
VBC
IB
Rotation

Rotation

Reactive Power

+kVAR

Q2: Leading PF (+)
VBC

VAB
IA
IC

IA
VCA

VCA

Active Power

+kW

-kW
Q3: Lagging PF (-)

Q4: Leading PF (+)
VBC

VBC

VAB

VCA

-kVAR

Reactive Power

Rotation

VAB

IB
IC
VCA

PowerLogic ION7550 / ION7650 Installation Guide

Step 10: View Meter Data
Use the softkeys to select which data to display. Use the left and right arrow
buttons to scroll through the available display screens.

Display Screens
Softkey
V,I,PF
Volts
Amps
Power
Energy1
Demand1
Pk Dmd1
V Bar, I Bar, P Bar
Summary1, Summary2
D Inputs
DI - I/O
D-Output
Anlg - I/O
Phasors
Name Plt
Events
Setpoint
Energy2
Demand2
Pk Dmd2
THD
V1 Harm, V2 Harm,...
I1 Harm, I2 Harm,...
TOU
TOU Egy
TOU Dmd1 & TOU Dmd2
*PQ Freq
*PQ Vmag1
*PQ Vmag2
*PQ Flk1
*PQ Flk2
*PQ Vdist
*PQ Vunb
*PQ Vhrm1
*PQ Vhrm2
V-Trend, I-Trend, P-Trend
*

Contents
Volts, Amps, Power Factor
Volts
Amps
Total Power
Energy delivered
Demand delivered
Peak Demand delivered
Voltage, Current and Power Bar Graphs
Volts/Amps Summary, Power Summary
Digital Inputs
Digital I/O on expansion I/O card
Digital Outputs
Analog In and Out
Phasors
Nameplate information
Events
Setpoint status
Energy received
Demand received
Peak Demand received
Volts and Amps Total Harmonic Distortion
V1, V2, V3, V4 harmonics
I1, I2, I3, I4, I5 harmonics
Time Of Use Active Rate / Season
TOU Energy delivered
TOU Peak Demand 1 and 2
Power Quality Power Frequency
PQ Supply Voltage 1
PQ Supply Voltage 2
PQ Flicker 1
PQ Flicker 2
PQ Voltage Disturbance
PQ Voltage Unbalance
PQ Voltage Harmonics 1
PQ Voltage Harmonics 2
Voltage, Current, Power Trends

Additional display screens for ION7650 meters with EN50160 option.

PowerLogic ION7550 / ION7650
with WebMeter and MeterM@il

Installation Guide

For further assistance
please contact us at:

Schneider Electric
Power Monitoring and Control
2195 Keating Cross Road
Saanichton, BC
Canada V8M 2A5
Tel: 1-250-652-7100
295 Tech Park Drive, Suite 100
Lavergne, TN 37086
USA
Tel: 1-615-287-3400
Electropole (38 EQI)
31, rue Pierre Mendès France
F - 38050 Grenoble Cédex 9
Tel : + 33 (0) 4 76 57 60 60
Getting technical support:
Contact your local Schneider Electric sales
representative for assistance or go to the
www.powerlogic.com website.

PowerLogic, ION, ION Enterprise, MeterM@il, WebMeter
and Modbus are either trademarks or registered
trademarks of Schneider Electric.
Electrical equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
70002-0247-10
© 2007 Schneider Electric. All rights reserved.
12/2007

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Creator Tool                    : FrameMaker 7.1
Modify Date                     : 2007:12:10 10:39-08:00
Create Date                     : 2007:12:10 10:31:11Z
Metadata Date                   : 2007:12:10 10:39-08:00
Format                          : application/pdf
Title                           : PowerLogic ION7550 / ION7650 Installation Guide
Creator                         : Schneider Electric
Document ID                     : uuid:905f310e-337b-49c7-8f48-6922ce5746cd
Instance ID                     : uuid:3186533f-5433-40ac-9094-e4019f35bcaa
Has XFA                         : No
Page Count                      : 28
Author                          : Schneider Electric

EXIF Metadata provided by EXIF.tools

Schneider Electric Weather Radio Ion7550 Users Manual PowerLogic / ION7650 Installation Guide

ION7650 to the manual f3d05de6-4626-4231-92bb-2385f84acfb1

Navigation menu

Versions of this User Manual:

Views

Navigation