Schneider Electric WISERCTPM200 Wiser200Amp PanelMeter-CT User Manual Wiser CT Specification v9 CT Final

Schneider Electric Wiser200Amp PanelMeter-CT Wiser CT Specification v9 CT Final

UserManual.wiki >

Schneider Electric >

WISERCTPM200 User Manual

User manual

2 1 General Features 1.1 System Metering type: Minimum 2 channel ZigBee SEP 1.1x power meter 1.2 Metering Measurements Power measurement (W) Power measurement reporting rate: Minimum 2 seconds for one channel. Programmable in 1 second step. Power measurement range: 45 – 48,000W/Channel Power measurement (W) With calibrated CT clamp on specified port Power measurement accuracy: PF = 1 0.8 < PF < 1 Power < 100W +/- 3W +/- 4W Power > 100W +/- 3% +/- 4% Power measurement (W) With non-calibrated CT clamp Power measurement accuracy: PF = 1 0.8 < PF < 1 Power < 100W +/- 5W +/- 6W Power > 100W +/- 5% +/- 6% • Remark: Only Computime approved CTs can be used. • Remark: Calibration and testing only be carried with current lower than 100A. 1.3 Power Supply Power supply 90- 240 VAC 1.4 Memory Backup Memory backup Non volatile memory backup. All current summation attributes saved to non volatile memory to keep cumulative current consumption through power outages. Data can be backup in every 60 seconds or longer Flash memory Store firmware for Over The Air (OTA) upgrade 1.5 Indicator LED indicator Network state indicator, minimum bi-color (red & green) 1.6 ZigBee ZigBee module ZigBee Smart Energy 1.1x Capable Frequency 2.4 - 2.48GHZ Communication range Up to 400m LOS in open site 2405-2480MHzZigBee SEP 1.1x power meter

3 2 Environmental Requirements 2.1 Environmental Ratings Min. Max. Units Operating Temperature -20 60 °C Storage Temperature -20 80 °C Operating Humidity 5 95 %RH • Indoor use only 3 Regulatory Requirements 3.1 Agency Approval FCC Regulation UL/CUL/ETL RoHS IEC 61000 4 Mechanical Outline 4.1 Base module Maximum dimensions: 6”x4.5”x2” 4.2 Current Transformer The maximum dimensions for the current transformer are show in the drawing below:

4 5 Electrical 5.1 Current Transformers (CT) The current transformers must be capable of measuring either consumption or generation. 5.2 Switches No Switch Function 1 PB Push button for manual commissioning/decommissioning (see section 7.1 for auto join requirements) 5.3 Terminals AC L1 Line 1 input voltage AC Neutral AC return CT Channel 1 Input socket 1 for CT clamp CT Channel 2 Input socket 2 for CT clamp CT Channel 3 Input socket 3 for CT clamp CT Channel 4 Input socket 4 for CT clamp

7 Key Establishment Time OTA SE Simple Metering Key Establishment Each Simple Metering Cluster shall contain the following attributes: All other clusters shall adhere to the ZigBee Smart Energy Specification.

8 7 Application Requirements 7.1 Auto Join The device shall power up initially in a state that beacons the ZigBee Smart Energy network at a minimum of once per minute to facilitate joining the HAN. This state shall also become active as soon as the device leaves a HAN. The device shall remain in this state until it joins a HAN. 7.2 Power Factor Calculation (Optional) The device shall be capable of calculating the power factor and reporting this measurement upon request. Disclaimer Schneider Electric reserves the right to make changes without further notice to any products herein to improve reliability, function, or design. Schneider Electric does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, not the rights of others. FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.The distance between user and products should be no less than 20cm